Effects of engine cooling water temperature on performance and exhaust emission characteristics of a multi-cylinder CI engine operated with Jatropha-Butanol blend

Renewable alternatives such as biofuels and optimisation of the engine operating parameters can enhance engine performance and reduce emissions. The temperature of the engine coolant is known to have significant influence on engine performance and emissions. Whereas much existing literature describes the effects of coolant temperature in engines using fossil derived fuels, very few studies have investigated these effects when biofuel is used as an alternative fuel. Jatropha oil is a non-edible biofuel which can substitute fossil diesel for compression ignition (CI) engine use. However, due to the high viscosity of Jatropha oil, technique such as transesterification, preheating the oil, mixing with other fuel is recommended for improved combustion and reduced emissions. In this study, Jatropha oil was blended separately with ethanol and butanol, at ratios of 80:20 and 70:30. The fuel properties of all four blends were measured and compared with diesel and jatropha oil. It was found that the 80% jatropha oil + 20% butanol blend was the most suitable alternative, as its properties were closest to that of diesel. A 2 cylinder Yanmar engine was used; the cooling water temperature was varied between 50°C and 95°C. In general, it was found that when the temperature of the cooling water was increased, the combustion process enhanced for both diesel and Jatropha-Butanol blend. The CO2 emissions for both diesel and biofuel blend were observed to increase with temperature. As a result CO, O2 and lambda values were observed to decrease when cooling water temperature increased. When the engine was operated using diesel, NOX emissions correlated in an opposite manner to smoke opacity; however, when the biofuel blend was used, NOX emissions and smoke opacity correlated in an identical manner. The brake thermal efficiencies were found to increase slightly as the temperature was increased. In contrast, for all fuels, the volumetric efficiency was observed to decrease as the coolant temperature was increased. Brake specific fuel consumption was observed to decrease as the temperature was increased and was higher on average when the biofuel was used, in comparison to diesel. The study concludes that the effects of engine coolant temperature on engine performance and emission characteristics differ between biofuel blend and fossil diesel operation. The coolant temperature needs to be optimised depending on the type of biofuel for optimum engine performance and reduced emissions.

Upgrading biomass fast pyrolysis liquids

A comprehensive examination is made of the characteristics and quality requirements of bio-oil from fast pyrolysis of biomass. An appreciation of the potential for bio-oil to meet a broad spectrum of applications in renewable energy has led to a significantly increased R&D activity that has focused on addressing liquid quality issues both for direct use for heat and power and indirect use for biofuels and green chemicals. This increased activity is evident in North America, Europe, and Asia with many new entrants as well as expansion of existing activities. The only disappointment is the more limited industrial development and also deployment of fast pyrolysis processes that are necessary to provide the basic bio-oil raw material. © 2012 American Institute of Chemical Engineers (AIChE).

Saccharomyces Cerevisiae as a biotechnological tool for ageing research:studies on translation and metabolism

The yeast Saccharomyces cerevisiae is an important model organism for the study of cell biology. The similarity between yeast and human genes and the conservation of fundamental pathways means it can be used to investigate characteristics of healthy and diseased cells throughout the lifespan. Yeast is an equally important biotechnological tool that has long been the organism of choice for the production of alcoholic beverages, bread and a large variety of industrial products. For example, yeast is used to manufacture biofuels, lubricants, detergents, industrial enzymes, food additives and pharmaceuticals such as anti-parasitics, anti-cancer compounds, hormones (including insulin), vaccines and nutraceuticals. Its function as a cell factory is possible because of the speed with which it can be grown to high cell yields, the knowledge that it is generally recognized as safe (GRAS) and the ease with which metabolism and cellular pathways, such as translation can be manipulated. In this thesis, these two pathways are explored in the context of their biotechnological application to ageing research: (i) understanding translational processes during the high-yielding production of membrane protein drug targets and (ii) the manipulation of yeast metabolism to study the molecule, L-carnosine, which has been proposed to have anti-ageing properties. In the first of these themes, the yeast strains, spt3?, srb5?, gcn5? and yTHCBMS1, were examined since they have been previously demonstrated to dramatically increase the yields of a target membrane protein (the aquaporin, Fps1) compared to wild-type cells. The mechanisms underlying this discovery were therefore investigated. All high yielding strains were shown to have an altered translational state (mostly characterised by an initiation block) and constitutive phosphorylation of the translational initiation factor, eIF2a. The relevance of the initiation block was further supported by the finding that other strains, with known initiation blocks, are also high yielding for Fps1. A correlation in all strains between increased Fps1 yields and increased production of the transcriptional activator protein, Gcn4, suggested that yields are subject to translational control. Analysis of the 5´ untranslated region (UTR) of FPS1 revealed two upstream open reading frames (uORFs). Mutagenesis data suggest that high yielding strains may circumvent these control elements through either a leaky scanning or a re-initiation mechanism. In the second theme, the dipeptide L-carnosine (ß-alanyl-L-histidine) was investigated: it has previously been shown to inhibit the growth of cancer cells but delay senescence in cultured human fibroblasts and extend the lifespan of male fruit flies. To understand these apparently contradictory properties, the effects of L-carnosine on yeast were studied. S. cerevisiae can respire aerobically when grown on a non-fermentable carbon source as a substrate but has a respiro-fermentative metabolism when grown on a fermentable carbon source; these metabolisms mimic normal cell and cancerous cell metabolisms, respectively. When yeast were grown on fermentable carbon sources, in the presence of L-carnosine, a reduction in cell growth and viability was observed, which was not apparent for cells grown on a non-fermentable carbon source. The metabolism-dependent mechanism was confirmed in the respiratory yeast species Pichia pastoris. Further analysis of S. cerevisiae yeast strains with deletions in their nutrient-sensing pathway, which result in an increase in respiratory metabolism, confirmed the metabolism-dependent effects of L-carnosine.

Heterogeneous catalysts for converting renewable feedstocks to fuels and chemicals

The combination of dwindling oil reserves and growing concerns over carbon dioxide emissions and associated climate change is driving the urgent development of routes to utilise renewable feedstocks as sustainable sources of fuel and chemicals. Catalysis has a rich history of facilitating energy-efficient selective molecular transformations and contributes to 90% of chemical manufacturing processes and to more than 20% of all industrial products. In a post-petroleum era, catalysis will be central to overcoming the engineering and scientific barriers to economically feasible routes to biofuels and chemicals. This chapter will highlight some of the recent developments in heterogeneous catalytic technology for the synthesis of fuels and chemicals from renewable resources, derived from plant and aquatic oil sources as well as lignocellulosic feedstocks. Particular attention will be paid to the challenges faced when developing new catalysts and importance of considering the design of pore architectures and effect of tuning surface polarity to improve catalyst compatibility with highly polar bio-based substrates.

In situ aberration corrected-transmission electron microscopy of magnesium oxide nanocatalysts for biodiesels

Biofuels are promising renewable energy sources and can be derived from vegetable oil feedstocks. Although solid catalysts show great promise in plant oil triglyceride transesterification to biodiesel, the identification of active sites and operating surface nanostructures created during their processing is essential for the development of efficient heterogeneous catalysts. Systematic, direct observations of dynamic MgO nanocatalysts from a magnesium hydroxide-methoxide precursor were performed under controlled calcination conditions using novel in situ aberration corrected-transmission electron microscopy at the 0.1 nm level and quantified with catalytic reactivity and physico-chemical studies. Surface structural modifications and the evolution of extended atomic scale glide defects implicate coplanar anion vacancies in active sites in the transesterification of triglycerides to biodiesel. The linear correlation between surface defect density (and therefore polarisability) and activity affords a simple means to fine tune new, energy efficient nanocatalysts for biofuel synthesis. © 2009 Springer Science+Business Media, LLC.

Catalytic upgrading of bio-oils by esterification

Biomass is the term given to naturally-produced organic matter resulting from photosynthesis, and represents the most abundant organic polymers on Earth. Consequently, there has been great interest in the potential exploitation of lignocellulosic biomass as a renewable feedstock for energy, materials and chemicals production. The energy sector has largely focused on the direct thermochemical processing of lignocellulose via pyrolysis/gasification for heat generation, and the co-production of bio-oils and bio-gas which may be upgraded to produce drop-in transportation fuels. This mini-review describes recent advances in the design and application of solid acid catalysts for the energy efficient upgrading of pyrolysis biofuels.

Thermal processing of miscanthus, sugarcane bagasse, sugarcane trash and their acid hydrolysis residues

The research presented in this thesis was developed as part of DIBANET, an EC funded project aiming to develop an energetically self-sustainable process for the production of diesel miscible biofuels (i.e. ethyl levulinate) via acid hydrolysis of selected biomass feedstocks. Three thermal conversion technologies, pyrolysis, gasification and combustion, were evaluated in the present work with the aim of recovering the energy stored in the acid hydrolysis solid residue (AHR). Mainly consisting of lignin and humins, the AHR can contain up to 80% of the energy in the original feedstock. Pyrolysis of AHR proved unsatisfactory, so attention focussed on gasification and combustion with the aim of producing heat and/or power to supply the energy demanded by the ethyl levulinate production process. A thermal processing rig consisting on a Laminar Entrained Flow Reactor (LEFR) equipped with solid and liquid collection and online gas analysis systems was designed and built to explore pyrolysis, gasification and air-blown combustion of AHR. Maximum liquid yield for pyrolysis of AHR was 30wt% with volatile conversion of 80%. Gas yield for AHR gasification was 78wt%, with 8wt% tar yields and conversion of volatiles close to 100%. 90wt% of the AHR was transformed into gas by combustion, with volatile conversions above 90%. 5volO2%-95vol%N2 gasification resulted in a nitrogen diluted, low heating value gas (2MJ/m3). Steam and oxygen-blown gasification of AHR were additionally investigated in a batch gasifier at KTH in Sweden. Steam promoted the formation of hydrogen (25vol%) and methane (14vol%) improving the gas heating value to 10MJ/m3, below the typical for steam gasification due to equipment limitations. Arrhenius kinetic parameters were calculated using data collected with the LEFR to provide reaction rate information for process design and optimisation. Activation energy (EA) and pre-exponential factor (ko in s-1) for pyrolysis (EA=80kJ/mol, lnko=14), gasification (EA=69kJ/mol, lnko=13) and combustion (EA=42kJ/mol, lnko=8) were calculated after linearly fitting the data using the random pore model. Kinetic parameters for pyrolysis and combustion were also determined by dynamic thermogravimetric analysis (TGA), including studies of the original biomass feedstocks for comparison. Results obtained by differential and integral isoconversional methods for activation energy determination were compared. Activation energy calculated by the Vyazovkin method was 103-204kJ/mol for pyrolysis of untreated feedstocks and 185-387kJ/mol for AHRs. Combustion activation energy was 138-163kJ/mol for biomass and 119-158 for AHRs. The non-linear least squares method was used to determine reaction model and pre-exponential factor. Pyrolysis and combustion of biomass were best modelled by a combination of third order reaction and 3 dimensional diffusion models, while AHR decomposed following the third order reaction for pyrolysis and the 3 dimensional diffusion for combustion.

Catalyst design for biorefining

The quest for sustainable resources to meet the demands of a rapidly rising global population while mitigating the risks of rising CO2 emissions and associated climate change, represents a grand challenge for humanity. Biomass offers the most readily implemented and low-cost solution for sustainable transportation fuels, and the only non-petroleum route to organic molecules for the manufacture of bulk, fine and speciality chemicals and polymers. To be considered truly sustainable, biomass must be derived fromresources which do not compete with agricultural land use for food production, or compromise the environment (e.g. via deforestation). Potential feedstocks include waste lignocellulosic or oil-based materials derived from plant or aquatic sources, with the so-called biorefinery concept offering the co-production of biofuels, platform chemicals and energy; analogous to today's petroleum refineries which deliver both high-volume/low-value (e.g. fuels and commodity chemicals) and lowvolume/ high-value (e.g. fine/speciality chemicals) products, thereby maximizing biomass valorization. This article addresses the challenges to catalytic biomass processing and highlights recent successes in the rational design of heterogeneous catalysts facilitated by advances in nanotechnology and the synthesis of templated porous materials, as well as the use of tailored catalyst surfaces to generate bifunctional solid acid/base materials or tune hydrophobicity.

Land resource requirements for bioenergy in India

This study presents a two stage process to determine suitable areas to grow fuel crops: i) FAO Agro Ecological Zones (AEZ) procedure is applied to four Indian states of different geographical characteristics; and ii) Modelling the growth of candidate crops with GEPIC water and nutrient model, which is used to determine potential yield of candidate crops in areas where irrigation water is brackish or soil is saline. Absence of digital soil maps, paucity of readily available climate data and knowledge of detailed requirements of candidate crops are some of the major problems, of which, a series of detailed maps will evaluate true potential of biofuels in India.

Experimental investigation of the fuel properties of glidfuel, palm oil mill effluent biodiesel and blends

Biofuels derived from industry waste have potential to substitute fossil fuels (Diesel and Gasoline) in internal combustion (IC) engines. Use of waste streams as fuels would help to reduce considerably life-cycle greenhouse gas emissions and minimise waste processing costs. In this study an investigation into the fuel properties of two waste derived biofuels were carried out, they are: (i) Glidfuel (GF) biofuel - a waste stream from paper industry, and (ii) Palm Oil Mill Effluent (POME) biodiesel - biodiesel produced from palm oil industry effluent through various treatment and transesterification process. GF and POME was mixed together at various proportions and separately with fossil diesel (FD) to assess the miscibility and various physical and chemical properties of the blends. Fuel properties such as kinematic viscosity, higher heating value, water content, acid number, density, flash point temperature, CHNO content, sulphur content, ash content, oxidation stability, cetane number and copper corrosion ratings of all the fuels were measured. The properties of GF, POME and various blends were compared with the corresponding properties of the standard FD. Significance of the fuel properties and their expected effects on combustion and exhaust emission characteristics of the IC engine were discussed. Results showed that most properties of both GF and POME biodiesel were comparable to FD. Both GF and POME were miscible with each other, and also separately with the FD. Flash point temperatures of GF and POME biodiesel were 40.7°C and 158.7°C respectively. The flash point temperature of GF was about 36% lower than corresponding FD. The water content in GF and FD were 0.74 (% wt) and 0.01 (% wt) respectively. Acidity values and corrosion ratings of both GF and POME biodiesel were low compared to corresponding value for FD. The study concluded that optimum GF-POME biofuel blends can substitute fossil diesel use in IC engines.

Síntese e caracterização de niobiosilicatos para produção de biocombustível

The mesoporous materials has been an special attention, among them was discovered in the 1990´s the mesoporous molecular sieve of SBA-15 type. The good features of the SBA- 15 makes this material very promising in catalysis, however, due to the absence of native active sites, it has low catalytic activity. In this way, different metals and oxides have been included in this molecular sieve as a means of introducing active sites and increase its catalytic activity. Among the oxides that are being researched, there is the niobium oxide, which presents strong acid sites and exists in abundance. Brazil is the largest producer of the mineral. On the other hand, the production of biofuels has been desired, but it requires the development of new catalysts for this purpose. The aim of this work was to develop silicate of niobium by impregnation and by new synthesis method for application in the cracking of moringa oil. The methodology consisted of inserting the niobium oxide either by postsynthesis process using wet impregnation and direct insertion. For direct insert a new method was developed for pH adjustment, being tested different pH, and the pH 2.2 was used different ratios of Si/Nb. The materials were characterized by different techniques such as: XRD, N2 adsorption, SEM, EDS, UV-visible, TG/DTG, DSC, TEM, acidity by thermodesorption of n-butilamine and FTIR. After this part of the catalysts developed by the two methods were tested in the thermocatalytic cracking of moringa oil, being used a simple distillation. All silicates of Niobium obtained showed a highly ordered structure, having high specific areas, good distribution of pore diameters, beyond present a morphology in the form of fibers. In the catalysts after synthesis was observed that the niobium inserted has so as octahedrally and tetrahedrally coordinated, demonstrating that there were also oxides formed on the external surface of SBA-15. The materials obtained in the direct synthesis are only tetrahedrally coordinated. The new synthesis method of pH adjusting by using the buffer solution for it, proved to be very efficient for the production of such materials, because the materials obtained showed characteristics and structures similar to the molecular sieve of SBA-15 type. Among the pH tested the material that presented better characteristics was synthesized at pH 2.2. The application of these materials in catalytic cracking showed a higher formation of organic liquids when compared to thermal cracking, in addition to significantly reducing the acidity and residues formed, demonstrating that the use of silicates of Niobium increases both the conversion and the selectivity of the products.

Os limites constitucionais ao exercício de direito de patente e seus reflexos na indústria do petróleo, gás natural e biocombustíveis

This dissertation deals with the constitutional limits on the exercise of patent rights and its effects on the oil, natural gas and biofuels. Held with the support of ANP / PETROBRAS, It seeks to show how the law will limit the exercise of industrial property, based on a reinterpretation of private law by the constitutional development perspective . Today it is a fact that Petrobras, a Brazilian joint venture, has the latest technology in various sectors of the oil industry, and is one of the highest investments in developing new technologies. The overall objective of this thesis is to establish the relationship between the public interest of the Petroleum Industry, Natural Gas and Biofuels and constitutional limits to the free exercise of patent rights, then confirm or refute our hypothesis that Article 71 on Industrial Property Law is contrary to the existing objectives in Article 3 of the Constitution of the Federative Republic of Brazil. The research aims to examine the relevant aspects of the legal nature attributed to IPGN constitutionally confronting the constitutional limits on the free exercise of patent rights, with the purpose to outline the state of the performance limits in the regulation of the economy, in particular the application of feasibility limitations on the right of property in favor of national interest on the strategic energy industry. The aim is to confront the fundamental rights to property and economic development, against the public interest, limiting these first. As to the objectives, the research will be theoretical and descriptive and harvest of industrial property, respect the possible impact of regulatory standards and limiting the right of ownership in the oil industry. To establish how the state will mitigate the intellectual property right, we discuss, at first, a definition of public interest from the general theory of state and sovereign character in order to establish a new concept of national interest and popular interest, which will in turn the definition of our concept of public interest. In the second phase, will be addressed the issue of industrial property rights and how to will be free exercise thereof, in the constitutional sphere, infra, and demonstrating the use of industrial property rights with examples of market and IPGN . After situating the industrial property rights in the constitution and national legislation, establish their relationship with the national and regional development, will be addressed in this chapter in particular the patent law, as most usual form of intellectual property protection in IPGN. Used a study highlighting the number of patents in the area of the analyzed industry, demonstrating with hard data the importance of a sector for industrial development. The relationship between the social function of intellectual property and the constitutional objective of development was characterized to demonstrate the strategic nature of oil to Brazil in the national and international scene, and put into question the hypothesis of the research which provides that even with large investments the lack of legal certainty in the sector turns out not to have a considerable volume of investment as it could.

Efeitos de fungicidas alternativos em folhas de Carthamus tinctorius L. (Asteraceae), potencial espécie para cultivo em agricultura familiar

The currently main development model on global society is driven by an economic rationality that endangers the environment and social justice. More and more, attention to this way of production and consumption is increasing, boosting research for sustainable development, with an environmental rationality that can harmonize nature preservation and welfare of all socioeconomic classes. One of the efforts on this sense is changing the sources supplying the energy demand, replacing fossil fuels for renewable and cleaner sources, such as biofuels. Carthamus tinctorius (safflower) is an oilseed crop with potential for biodiesel production, with good oil yield and chemical profile, allied to good adaptation to climates such like the northeastern semiarid lands of Brazil. With public policies fomentation, the use of this species may be an interesting alternative for family farming. In farming in general, the use of pesticides to prevent and combat diseases and plagues is common, which is not a sustainable practice. Thus, there are researched alternative, less dangerous substances. In this study, it was aimed to assess if neem (Azadirachta indica) leaf extract (20% m/v) and Bordeaux mixture (copper sulfate) have effects on safflower. It was also aimed to verify acceptance of farmers on safflower crop in Apodi, a municipality in Rio Grande do Norte state, Brazil, in view of it being localized in the aimed region for this crop cultivation. Besides that, understanding that the farmers’ knowledge and inclination to adopt the crop is fundamental for the introduction of this species and socioeconomic growth due to its exploration. In addition, a booklet with basic information on safflower was produced. In the field experiment, the fungicides were pulverized on plants cultivated in field experimental plots, with collection of leaf samples for analysis on anatomy, cuticle, and epicuticular wax morphology, the protective layer that interfaces with the surrounding ambient. In Apodi, forty-five farmers from Potiguar Cooperative of Apiculture and Sustainable Rural Development (COOPAPI) underwent semi-structured interviews, which also addressed their assessment on currently cultivated crops and perception of pesticide uses and sustainable alternatives. After comparing using analysis of variance, it was found that there was no difference between treatments in the experiment, as well as no anatomical or morphological modifications. Safflower acceptation among farmers was wide, with 84% of interviewees believing in a perspective of good incomes. The current scenario, comprised of low crop diversity, fragile in face of droughts and plagues, can partially explain this opinion. The booklet was effective in catching people attention for the species potential. There was wide acknowledgement on the importance of alternative pesticides, justified by health security. Based on the assessed parameter in the results of this research, the treatments here utilized may be recommended as fungicides for safflower. Given the crop susceptibility to fungi in heavy rainy period, it is advised that its potential introduction on the region shall be focused on semiarid areas.

Consórcio de cártamo e feijão caupi: alternativa para a produção de biodiesel na agricultura familiar

The new development strategies should operate mainly in the areas of energy efficiency and sustainable agriculture. Thus, the substitution of fossil fuels with biofuels, such as biodiesel, is increasingly on the agenda. The cultivation of oilseed plants for biodiesel production must take place in integrated systems that enable best environmental benefits and are more economically significant. The objectives of this study were to assess the morphological, anatomic, and physiological characteristics of safflower (Carthamus tinctorius L., promising oilseed for biodiesel production) grown in monoculture and intercropping with cowpea bean (Vigna unguiculata L. Walp.); and identify socioeconomic family farmers and verify their acceptance about safflower as an energy crop. The methodology used for the analysis of safflower growth in monoculture and intercropped with beans, were morphoanatomical and histochemical analyzes, made with samples of plants grown in the field in two cropping systems throughout the range of the life cycle of these plants. There were no changes in growth and anatomy of plants, even in the consortium, which is satisfactory to indicate the intercropping system for those crops and can be a good alternative for the family farmer, who may have safflower as a source of income without giving up planting their livelihood. To check the acceptance of safflower by farmers, interviews were made to family farmers by Canudos agrovila in Ceará-Mirim/RN. It was noticed that many of them accept the introduction of safflower as oil crop, although unaware of the species, and that, being more resistant to drought, safflower help in the stability of families who depend on the weather conditions for success their current crops. In general, it is concluded that safflower has features that allows it to be grown in consortium for biodiesel production combined with the production of food, such as cowpea, and can be used enabling better development for family farmers.