Material transport in self-assembled InAs/GaAs quantum dot ensemble

Introducing the growth interruption between the InAs deposition and subsequent GaAs growth in self-assembled quantum dot (QD) structures, the material transport process in the InAs layers has been investigated by photoluminescence and transmission electron microscopy measurement. InAs material in structures without misfit dislocations transfers from the wetting layer to QDs corresponding to the red-shift of PL peak energy due to interruption. On the other hand, the PL peak shifts to higher energy in the structures with dislocations. In this case, the misfit dislocations would capture the InAs material from the surrounding wetting layer and coherent islands leading to the reduction of the size of these QDs. The variations in the PL intensity and Linewidth are also discussed.

Influence of interdot electronic coupling on photoluminescence spectra of self-assembled InAs/GaAs quantum dots

The influence of interdot electronic coupling on photoluminescence (PL) spectra of self-assembled InAs/GaAs quantum dots (QDs) has been systematically investigated combining with the measurement of transmission electron microscopy. The experimentally observed fast red-shift of PL energy and an anomalous reduction of the linewidth with increasing temperature indicate that the QD ensemble can be regarded as a coupled system. The study of multilayer vertically coupled QD structures shows that a red-shift of PL peak energy and a reduction of PL linewidth are expected as the number of QD layers is increased. On the other hand, two layer QDs with different sizes have been grown according to the mechanism of a vertically correlated arrangement. However, only one PL peak related to the large QD ensemble has been observed due to the strong coupling in InAs pairs. A new possible mechanism to reduce the PL linewidth of QD ensemble is also discussed.

The enhancement of diffusion by strain of InAs quantum dots in a GaAs matrix

We investigate the annealing behavior of Photoluminescence (PL) from self-assembled InAs quantum dots (QDs) with different thicknesses GaAs cap layers. The diffusion introduced by annealing treatment results in a blue-shift of the QD PL peak, and a decrease in the integrated intensity. The strain present in QDs enhances the diffusion, and the QDs with the cap layers of different thicknesses will experience a strain of different strength. This can lend to a, better understanding of the larger blue-shift of the PL peak of the deeper buried QDs, and the different variance of the full width at half maximum of the luminescence from QDs with the cap layers of different thicknesses.

实时数据流系统降载方法研究

随着信息技术的发展，出现了大量的数据流应用，如传感器数据处理、网络监控、金融数据分析等。在这些应用中，数据是一种连续、时变、有序、无限的序列，查询大多数都是采用连续查询方式。这种数据和查询的连续性对管理系统的资源需求很大。当系统资源不能满足查询处理要求，即查询处理任务超过系统的最大处理能力，用户的查询将得不到及时、正确地处理。同时，如果查询处理时间超过了查询截止期需求，查询结果就没有意义，甚至会造成灾难性后果。目前，很多研究都集中于数据流系统的降载，对支持实时查询处理的实时数据流系统降载的研究比较少。 本论文主要研究支持实时查询处理的实时数据流管理系统中的降载方法，主要包括如下三个方面：随机降载方法、语义降载方法与共享滑动窗口连接操作的降载方法。最后，通过实时数据流管理系统测试平台验证了所提出算法在提高系统吞吐量与降低截止期错失率方面表现出良好的性能。 针对实时数据流应用需求，提出了一种适合实时查询的数据流处理框架结构RT-DSPA和相应的多层过载处理策略MLOHS，为降载方法的研究提供一个框架基础。RT-DSPA分为用户层、DSMS层以及数据源层多个功能模块，具有多层性、可扩展性、健壮性以及可配置性的特点。 在随机降载方面，提出了一种基于数据流流速的负载估计算法；在实时数据流处理框架与负载估计算法的基础上，提出了一种截止期敏感的随机降载算法RLS-EDA。由于系统负载经常波动较大，该算法利用截止期的特点，使用暂存所丢弃元组技术充分地利用CPU空闲资源，使降载执行后系统的吞吐量得到提高，进而尽可能地降低查询截止期错失率；最后，讨论了降载过程中的队列维护策略、含共享操作符查询网络中的降载位置以及降载操作符插入查询网络的算法。实验结果表明，在系统负载波动较大的情况下，RLS-EDA算法表现出良好的性能。 在充分了解数据流及查询特征的情况下，语义降载表现出更好的降载效果。为明确语义降载时使用到的语义，提出了元组价值、价值等级的概念，给出价值等级划分时发生冲突的解决方法。设计了适合实时数据流管理系统的价值等级–执行开销优先级表和截止期–价值密度优先级表，其在确定优先级时可考虑多维因素。基于这两种优先级表设计，提出了相对应的语义降载算法SLS-PT-VD&EC和SLS-PT-D&TVD。基于优先级表的语义降载算法能够灵活地满足用户的不同需求，同时提高系统降载时的性能。 最后，针对共享滑动窗口连接操作符的过载情况，利用查询截止期的特点，提出了一种基于暂存丢弃元组技术的共享滑动窗口连接的降载算法LS-SJRT；为减小LS-SJRT算法的降载开销，提出了一种改进的基于调节滑动窗口宽度的共享滑动窗口连接降载算法LS-SJRT-CW。实验结果显示这两种算法在共享连接操作符过载时都能够表现出较好的性能。

Monodisperse raspberry-like gold submicrometer spheres: Large-scale synthesis and interface assembling for colloid sphere array

We first suggested a one-pot method to synthesize monodisperse raspberry-like submicrometer gold spheres (MRSGS) with high yield. The resulting gold spheres were characterized by scanning electron microscopy, transmission electron microscopy, energy-dispersed X-ray spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and electrochemical technology. It was found that the rough structure provided by raspberry-like gold spheres led to a tremendous electrochemical active area, which was very important because these novel hierarchical gold spheres will probably find important applications in biosensors, electrocatalysis, and others.

One Pot, Facile Synthesis of Hierarchical Silver Nanostrip Assembling Architecture

Here we present a simple wet-chemical approach to synthesize flower-like silver nanostrip assembling architecture at room temperature. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) images indicate that these microstructures with the diameter of similar to 500nm exhibit hietarchical characteristic. X-ray diffraction (XRD), energy-dispersed X-ray spectroscopy (EDX) and Raman spectroscopy indicate that poly (o-diaminobenzene) (PDB) also exists in the silver hierarchical microstructure.

Solvothermal synthesis of well-dispersed NaMgF3 nanocrystals and their optical properties

Complex metal fluoride NaMgF3 nanocrystals were successfully synthesized via a solvothermal method at a relatively low temperature with the presence of oleic acid, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectra, photoluminescence (PL) excitation and emission spectra, respectively. fit the synthetic process, oleic acid as a Surfactant played a Crucial role in confining the growth and solubility of the NaMgF3 nanocrystals. The as-prepared NaMgF3 nanocrystals have quasi-spherical shape with a narrow distribution. A possible formation mechanism of the nanocrystals was proposed based on the effect of oleic acid. The as-prepared NaMgF3 nanocrystals are highly crystalline and well-dispersed in cyclohexane to form stable and clear colloidal Solutions, which demonstrate a strong emission band centered at 400 nm in photoluminescence (PL) spectra compared with the cyclohexane solvent.

Self-assembly of ionic liquids-stabilized Pt nanoparticles into two-dimensional patterned nanostructures at the air-water interface

In this paper, we demonstrate the self-assembly of ionic liquids (ILs)-stabilized Pt nanoparticles into two-dimensional (2D) patterned nanostructures at the air-water interface under ambient conditions. Here, ILs are not used as solvents but as mediators by virtue of their pronounced self-organization ability in synthesis of self-assembled, highly organized hybrid Pt nanostructures. It is also found that the morphologies of the 2D patterned nanostructures are directly connected with the quantities of ILs. Due to the special structures of ILs-stabilized Pt nanoparticles, 2D patterned Pt nanostructures can be formed through the pi-pi stack interactions and hydrogen bonds. The resulting 2D patterned Pt nanostructures exhibit good electrocatalytic activity toward oxygen reduction.

Syntheses of Ag, PbSe, and PbTe nanocrystals and their binary self-assembly exploration at low size-ratio

Nanocrystals of Ag, PbSe, and PbTe were prepared via a high-temperature organic solution approach, respectively. Using a size-selection technique, the size-distribution of each set of nanocrystals could be fine-tuned and finally monodisperse products were achieved. Superlattice structure of binary self-assemblies in low size-ratio were also explored and characterized by transmission electron microscopy. It is realized that a success of achieving binary self-assembly pattern is greatly dependent on several key factors including particle size-distributions, relative concentrations of both components, as well as the size-ratios between Ag and PbSe (or PbTe) nanocrystals.

Synthesis and self-assembly of cetyltrimethylammonium bromide-capped gold nanoparticles

In this article, cetyltrimethylammonium bromide (CTAB)-capped gold nanoparticles were synthesized successfully by using CTAB as a phase-transfer catalyst and stabilizer simultaneously in a two-phase toluene/water system. The as-prepared gold nanoparticles were characterized and analyzed by virtue of X-ray photoelectron spectroscopy, UV-visible absorbance spectroscopy, and infrared spectroscopy. The particle size information and collective self-assembling properties of the CTAB-capped gold nanoparticles on carbon-coated copper grid and mica were evaluated by transmission electron microscopy and atomic force microscopy, respectively. As a result it is demonstrated that the 3-D CTAB monolayers on a gold cluster are in the disordered liquid state. The interparticle spacing can be controlled either physically by the inherent particle-to-particle interactions or chemically by molecular linker. The assembly of both nanoparticles and linker-bridged nanonetworks on mica follows a hydrophobic interaction mechanism.

Determination of molecular weight and molecular sizes of polymers by high temperature gel permeation chromatography with a static and dynamic laser light scattering detector

Flow-mode static and dynamic laser light scattering (SLS/DLS) studies of polymers, including polystyrene, polyethylene, polypropylene and poly(dimethylsiloxane) (PDMS), in 1,2,4-trichlorobenzene (TCB) at 150 degreesC were performed on a high temperature gel permeation chromatography (GPC) coupled with a SLS/DLS detector. Both absolute molecular weight (M) and molecular sizes (radius of gyration, R-g and hydrodynamic radius, R-h) of polymers eluting from the GPC columns were obtained simultaneously. The conformation of different polymers in TCB at 150 degreesC were discussed according to the scaling relationships between R-g, R-h and M and the rho-ratio (p = R-g/R-h). Flow-mode DLS results of PDMS were verified by batch-mode DLS study of the same sample. The presented technique was proved to be a convenient and quick method to study the shape and conformation of polymers in solution at high temperature. However, the flow-mode DLS was only applicable for high molecular weight polymers with a higher refractive index increment such as PDMS.

Influence of capping ligands on the self-organizations of gold nanoparticles into superlattice from CTAB reverse micelles

Gold nanoparticles with size 3-10 nm (diameter) were prepared by the reduction of HAuCl4 in a CTAB/octane + 1-butanol/H2O reverse micelle system using NaBH4 as the reducing agent. The as-formed gold nanoparticle colloid was characterized by UV/vis absorption spectrum and transmission electron microscopy(TEM). Various capping ligands, such as alkylthiols with different chain length and shape, trioctylphosphine (TOP), and pyridine are used to passivate the gold nanoparticles for the purpose of self-organization into superstructures. It is shown that the ligands have a great influence on the self-organization of gold nanoparticles into superlattices, and dodecanethiol C12H25SH is confirmed to be the best ligand for the self-organization. Self-organization of C12H25SH-capped gold nanoparticles into 1D, 2D and 3D superlattices has been observed on the carbon-coated copper grid by TEM without using any selective precipitation process.

Formation of ordered arrays of gold nanoparticles from CTAB reverse micelles

In this presentation, a reverse micelle technique was described to create colloid gold nanoparticles and their self-organization into superlattices. Gold nanoparticles were prepared by the reduction of HAuCL4 in CTAB/octane + 1-butanol/H2O reverse micelle system using NaBH4 as reducing agent. Dodecanethiol (C12H25SH) was used to passivate the gold nanoparticles immediately after formation of the gold colloid. After re-dispersing in toluene under ultrasonication, a supernatant containing nearly monodispersed dodecanethiol-capped gold nanoparticles was obtained. Self-organization of the gold nanoparticles into 1D, 2D and 3D superlattices was observed on the carbon-coated copper grid by TEM. UV-vis absorption spectra were also used to characterize the gold colloids with and without dodecanethiol capping. (C) 2001 Elsevier Science B.V. All rights reserved.

LB multilayers and superlattice films of erbium fatty acid salts

Multilayers of Y-type bilayers of pure and mixed erbium palmitate(EP), nonadecanate(Er) and behenate(EB) on CaF2 substrates were prepared by conventional Langmuir-Blodgett (LB) method. II is demonstrated that two systems composed of alternating bilayer of different fatty acid salts are unidimensional superlattices. These LB films were characterized by means of x-ray photoelectronic Spectrometry (XPS), FTIR and x-ray diffraction (XRD) measurements.