Unsteady natural convection from a horizontal annulus filled with a porous medium

The unsteady natural convection flow from a horizontal cylindrical annulus filled with a non-Darcy porous medium has been studied. The unsteadiness in the problem arises due to the impulsive change in the wall temperature of the outer cylinder. The Navier–Stokes equations along with the energy equation governing the unsteady natural convection flow have been solved by the finite-volume method. The effect of time variation on the heat transfer is more pronounced only in a small time interval immediately after the start of the impulsive motion and the steady state is reached after certain time. The results show that the annulus completely filled with a porous medium has the best insulating effectiveness. Convection in the horizontal annulus is confined mostly at top and bottom regions. Hence, only these regions should be insulated. In case of annulus partially filled with a porous material, insulating the region near the outer cylinder is more effective than insulating the region near the inner cylinder. The effect of Darcy number on the heat transfer is more pronounced than that of the Grashof number.

Understanding data flow and security requirements in wireless Body Area Networks for healthcare

The Body Area Network (BAN) is an emerging technology that focuses on monitoring physiological data in, on and around the human body. BAN technology permits wearable and implanted sensors to collect vital data about the human body and transmit it to other nodes via low-energy communication. In this paper, we investigate interactions in terms of data flows between parties involved in BANs under four different scenarios targeting outdoor and indoor medical environments: hospital, home, emergency and open areas. Based on these scenarios, we identify data flow requirements between BAN elements such as sensors and control units (CUs) and parties involved in BANs such as the patient, doctors, nurses and relatives. Identified requirements are used to generate BAN data flow models. Petri Nets (PNs) are used as the formal modelling language. We check the validity of the models and compare them with the existing related work. Finally, using the models, we identify communication and security requirements based on the most common active and passive attack scenarios.

Long-term effects of physical activity level on changes in healthy body mass index over 12 years in young adult women

Objectives To examine the effects of overall level and timing of physical activity (PA) on changes from a healthy body mass index (BMI) category over 12 years in young adult women. Patients and Methods Participants in the Australian Longitudinal Study on Women's Health (younger cohort, born 1973-1978) completed surveys between 2000 (age 22-27 years) and 2012 (age 34-39 years). Physical activity was measured in 2000, 2003, 2006, and 2009 and was categorized as very low, low, active, or very active at each survey, and a cumulative PA score for this 9-year period was created. Logistic regression was used to examine relationships between PA accumulated across all surveys (cumulative PA model) and PA at each survey (critical periods PA model), with change in BMI category (from healthy to overweight or healthy to obese) from 2000 to 2012. Results In women with a healthy BMI in 2000, there were clear dose-response relationships between accumulated PA and transition to overweight (P=.03) and obesity (P<.01) between 2000 and 2012. The critical periods analysis indicated that very active levels of PA at the 2006 survey (when the women were 28-33 years old) and active or very active PA at the 2009 survey (age 31-36 years) were most protective against transitioning to overweight and obesity. Conclusion These findings confirm that maintenance of very high PA levels throughout young adulthood will significantly reduce the risk of becoming overweight or obese. There seems to be a critical period for maintaining high levels of activity at the life stage when many women face competing demands of caring for infants and young children.

Accumulation of glycine in the fat body of the silkworm, bombyx mori L. [31]

INVESTIGATIONS of intestinal transport of amino-acids in the locust1,2 and silkworm3,4 have shown no evidence for active accumulation in a transport from the insect gut of amino-acids. When glycine-2-14C was administered in vivo to fifth instar larvae of the silkworm, 96 per cent of the radioactivity was incorporated into various tissues within 1 h whereas in vitro only 19 per cent of the activity was transported by the mid-gut of silkworm (unpublished work). These results suggested that continued absorption of glycine by the intestine could be aided by a facilitated diffusion mechanism in which amino-acids are rapidly removed from the site of absorption either by accumulation into other tissues or by degradation. Although the insect fat body has been assigned both accumulatory and dissimilatory roles5, the mechanism of accumulation of amino-acids has not been investigated. Our present experiments show that the silkworm fat body possesses an efficient mechanism for accumulating glycine and that both the accumulation and the release of glycine are metabolically controlled.

Steady flow of a maxwell fluid in a porous cylindrical annulus with circular cross-section

When a fluid with memory is injected into any flow region some assumptions regarding the initial state of stress have to be made in order to determine the state of stress at any subsequent instant. For a Maxwell fluid, it is assumed that the fluid near the surface of injection is suddenly stressed and responds by starting flow in accordance with the mechanical model chosen. The flow of a Maxwell fluid with a single relaxation time has been determined under the above assumption in the following two cases: (i) annulus between two porous concentric circular cylinders, and (ii) space between two porous and infinitely extending parallel plates. The nature of flow in the present case is similar to that of the Reiner-Rivlin fluids obtained by Narasimhan2).

Significant effects of Pgi genotype and body reserves on lifespan in the Glanville fritillary butterfly

Individuals with a particular variant of the gene phosphoglucose isomerase (Pgi ) have been shown to have superior dispersal capacity and fecundity in the Glanville fritillary butterfly (Melitaea cinxia), raising questions about the mechanisms that maintain polymorphism in this gene in the field. Here, we investigate how variation in the Pgi genotype affects female and male life history under controlled conditions. The most striking effect is the longer lifespan of genotypes with high dispersal capacity, especially in nonreproducing females. Butterflies use body reserves for somatic maintenance and reproduction, but
different resources (in thorax versus abdomen) are used under dissimilar conditions, with some interactions with the Pgi genotype. These results indicate life-history trade-offs that involve resource allocation and genotype!environment interactions, and these trade-offs are likely to contribute to the maintenance of Pgi polymorphism in the natural populations.

Steady laminar flow with suction or injection and heat transfer through porous pipe

Following the method due to Bhatnagar (P. L.) [Jour. Ind. Inst. Sic., 1968, 1, 50, 1], we have discussed in this paper the problem of suction and injection and that of heat transfer for a viscous, incompressible fluid through a porous pipe of uniform circular cross-section, the wall of the pipe being maintained at constant temperature. The method utilises some important properties of differential equations and some transformations that enable the solution of the two-point boundary value and eigenvalue problems without using trial and error method. In fact, each integration provides us with a solution for a suction parameter and a Reynolds number without imposing the conditions of smallness on them. Investigations on non-Newtonian fluids and on other bounding geometries will be published elsewhere.

Studies in bubble formation - IV: bubble formation at porous discs

Bubble formation from porous discs submerged in liquids of different physical properties has been investigated. It is found the number of sites effective for bubble formation is much smaller than the total potentially available sites. The number of effective sites is found to be a function of the surface tension, viscosity, and density of the liquid and the gas flow rate through the disc. A model proposed on the basis of bubble formation from an isolated nozzle and the close packed arrangement of the formed bubbles, explains the phenomenon adequately. © 1970.

Flow of a power law fluid in an annulus with porous walls

The steady flow of a power law fluid in annuli with porous walls is investigated. The solution for the axial velocity component is obtained as a power series in terms of the cross flow Reynolds number, the first term of the series giving the solution for the case of the solid wall annulus. The cross flow is restricted to be such that the rate of injection of fluid at one wall of the annulus is equal to the rate of suction at the other wall and also we have considered only very small values of the cross flow velocity. The velocity profiles are drawn for different values of n and for different gaps and the results are discussed in detail. The behaviour of the average flux, in different eases is also discussed.

Compressible axially symmetric laminar boundary layer flow in the stagnation region of a blunt body in the presence of magnetic field

In this paper, the steady laminar viscous hypersonic flow of an electrically conducting fluid in the region of the stagnation point of an insulating blunt body in the presence of a radial magnetic field is studied by similarity solution approach, taking into account the variation of the product of density and viscosity across the boundary layer. The two coupled non-linear ordinary differential equations are solved simultaneously using Runge-Kutta-Gill method. It has been found that the effect of the variation of the product of density and viscosity on skin friction coefficient and Nusselt number is appreciable. The skin friction coefficient increases but Nusselt number decreases as the magnetic field or the total enthalpy at the wall increases

Loading of itraconazole into porous silica and silicon microparticles: characterization and dissolution tests

Most new drug molecules discovered today suffer from poor bioavailability. Poor oral bioavailability results mainly from poor dissolution properties of hydrophobic drug molecules, because the drug dissolution is often the rate-limiting event of the drug’s absorption through the intestinal wall into the systemic circulation. During the last few years, the use of mesoporous silica and silicon particles as oral drug delivery vehicles has been widely studied, and there have been promising results of their suitability to enhance the physicochemical properties of poorly soluble drug molecules. Mesoporous silica and silicon particles can be used to enhance the solubility and dissolution rate of a drug by incorporating the drug inside the pores, which are only a few times larger than the drug molecules, and thus, breaking the crystalline structure into a disordered, amorphous form with better dissolution properties. Also, the high surface area of the mesoporous particles improves the dissolution rate of the incorporated drug. In addition, the mesoporous materials can also enhance the permeability of large, hydrophilic drug substances across biological barriers. T he loading process of drugs into silica and silicon mesopores is mainly based on the adsorption of drug molecules from a loading solution into the silica or silicon pore walls. There are several factors that affect the loading process: the surface area, the pore size, the total pore volume, the pore geometry and surface chemistry of the mesoporous material, as well as the chemical nature of the drugs and the solvents. Furthermore, both the pore and the surface structure of the particles also affect the drug release kinetics. In this study, the loading of itraconazole into mesoporous silica (Syloid AL-1 and Syloid 244) and silicon (TOPSi and TCPSi) microparticles was studied, as well as the release of itraconazole from the microparticles and its stability after loading. Itraconazole was selected for this study because of its highly hydrophobic and poorly soluble nature. Different mesoporous materials with different surface structures, pore volumes and surface areas were selected in order to evaluate the structural effect of the particles on the loading degree and dissolution behaviour of the drug using different loading parameters. The loaded particles were characterized with various analytical methods, and the drug release from the particles was assessed by in vitro dissolution tests. The results showed that the loaded drug was apparently in amorphous form after loading, and that the loading process did not alter the chemical structure of the silica or silicon surface. Both the mesoporous silica and silicon microparticles enhanced the solubility and dissolution rate of itraconazole. Moreover, the physicochemical properties of the particles and the loading procedure were shown to have an effect on the drug loading efficiency and drug release kinetics. Finally, the mesoporous silicon particles loaded with itraconazole were found to be unstable under stressed conditions (at 38 qC and 70 % relative humidity).

The Path to a Porous Semiconductor Multilayer

Thin films are the basis of much of recent technological advance, ranging from coatings with mechanical or optical benefits to platforms for nanoscale electronics. In the latter, semiconductors have been the norm ever since silicon became the main construction material for a multitude of electronical components. The array of characteristics of silicon-based systems can be widened by manipulating the structure of the thin films at the nanoscale - for instance, by making them porous. The different characteristics of different films can then to some extent be combined by simple superposition. Thin films can be manufactured using many different methods. One emerging field is cluster beam deposition, where aggregates of hundreds or thousands of atoms are deposited one by one to form a layer, the characteristics of which depend on the parameters of deposition. One critical parameter is deposition energy, which dictates how porous, if at all, the layer becomes. Other parameters, such as sputtering rate and aggregation conditions, have an effect on the size and consistency of the individual clusters. Understanding nanoscale processes, which cannot be observed experimentally, is fundamental to optimizing experimental techniques and inventing new possibilities for advances at this scale. Atomistic computer simulations offer a window to the world of nanometers and nanoseconds in a way unparalleled by the most accurate of microscopes. Transmission electron microscope image simulations can then bridge this gap by providing a tangible link between the simulated and the experimental. In this thesis, the entire process of cluster beam deposition is explored using molecular dynamics and image simulations. The process begins with the formation of the clusters, which is investigated for Si/Ge in an Ar atmosphere. The structure of the clusters is optimized to bring it as close to the experimental ideal as possible. Then, clusters are deposited, one by one, onto a substrate, until a sufficiently thick layer has been produced. Finally, the concept is expanded by further deposition with different parameters, resulting in multiple superimposed layers of different porosities. This work demonstrates how the aggregation of clusters is not entirely understood within the scope of the approximations used in the simulations; yet, it is also shown how the continued deposition of clusters with a varying deposition energy can lead to a novel kind of nanostructured thin film: a multielemental porous multilayer. According to theory, these new structures have characteristics that can be tailored for a variety of applications, with precision heretofore unseen in conventional multilayer manufacture.

High Rate Capability of Porous LiNi1/3Co1/3Mn1/3O2 Synthesized by Polymer Template Route

Layered LiNi1/3Co1/3Mn1/3O2, which is isostructural with LiCoO2, is considered as a potential cathode material for Li-ion batteries. Submicrometer sized porous particles are useful for high discharge rates. The present work involves a synthesis of submicrometer sized porous particles of LiNi1/3Co1/3Mn1/3O2 using a triblock copolymer as a soft template. The precursor obtained from the reaction is heated at different temperatures between 600 and 900 degrees C for 6 h to get the final product samples. The compound attains increased crystallinity with an increase in the temperature of preparation. However, there is a decrease in the surface area and also in the porosity of the sample. Nevertheless, the LiNi1/3Co1/3Mn1/3O2 sample prepared at 900 degrees C exhibits a high rate capability and stable capacity retention on cycling. The electrochemical performance of LiNi1/3Co1/3Mn1/3O2 prepared in the absence of the polymer template is inferior to that of the sample prepared in the presence of the polymer template. (C) 2010 The Electrochemical Society. [DOI: 10.1149/1.3364944] All rights reserved.

The Physical Strenuousness of Work is Slightly Associated with an Upward Trend in the Body Mass Index

This paper explores the relationship between the physical strenuousness of work and the body mass index in Finland, using individual microdata over the period 1972-2002. The data contain self-reported information about the physical strenuousness of a respondent’s current occupation. Our estimates show that the changes in the physical strenuousness of work can explain around 8% at most of the definite increase in BMI observed over the period. The main reason for this appears to be that the quantitative magnitude of the effect of the physical strenuousness of work on BMI is rather moderate. Hence, according to the point estimates, BMI is only around 1.5% lower when one’s current occupation is physically very demanding and involves lifting and carrying heavy objects compared with sedentary job (reference group of the estimations), other things being equal. Accordingly, the changes in eating habits and the amount of physical activity during leisure time must be the most important contributors to the upward trend in BMI in industrialised countries, but not the changes in the labour market structure.