Simulations to design an online motion compensation system for scanned particle beams

Respiration-induced target motion is a major problem in intensity-modulated radiation therapy. Beam segments are delivered serially to form the total dose distribution. In the presence of motion, the spatial relation between dose deposition from different segments will be lost. Usually, this results in over-and underdosage. Besides such interplay effects between target motion and dynamic beam delivery as known from photon therapy, changes in internal density have an impact on delivered dose for intensity-modulated charged particle therapy. In this study, we have analysed interplay effects between raster scanned carbon ion beams and target motion. Furthermore, the potential of an online motion strategy was assessed in several simulations. An extended version of the clinical treatment planning software was used to calculate dose distributions to moving targets with and without motion compensation. For motion compensation, each individual ion pencil beam tracked the planned target position in the lateral aswell as longitudinal direction. Target translations and rotations, including changes in internal density, were simulated. Target motion simulating breathing resulted in severe degradation of delivered dose distributions. For example, for motion amplitudes of +/- 15 mm, only 47% of the target volume received 80% of the planned dose. Unpredictability of resulting dose distributions was demonstrated by varying motion parameters. On the other hand, motion compensation allowed for dose distributions for moving targets comparable to those for static targets. Even limited compensation precision (standard deviation similar to 2 mm), introduced to simulate possible limitations of real-time target tracking, resulted in less than 3% loss in dose homogeneity.

Photochemistry of Halogens in the Marine Atmosphere

Diatomic halogen molecules diffusing into the marine atmosphere are photodissociated to atoms in daylight more rapidly than they undergo other fates. The geochemistry of ‘gaseous halogens’ is considered in terms of photolysis rates and the secondary reactions of the atoms produced. Diatomic halogens could be photolyzed predominantly by day and adsorbed on aerosol by night without yielding diurnal variations in currently measurable variables. Halogen atoms in the marine atmosphere react with ozone more rapidly than with other marine tropospheric constituents, this reaction yielding haloxy radicals that are also reactive.

Nanostructure and mechanical measurement of highly oriented lamellae of melt-drawn HDPE by scanning probe microscopy

Scanning probe microscopy was used to simultaneously determine the molecular chain structure and intrinsic mechanical properties, including anisotropic elastic modulus and friction, for lamellae of highly oriented high-density polyethylene (HDPE) obtained by the melt-drawn method. The molecular-scale image of the highly oriented lamellae by friction force microscopy (FFM) clearly shows that the molecular chains are aligned parallel to the drawing direction, and the periodicities along and perpendicular to the drawing direction are 0.26 and 0.50 nm, respectively. The results indicate that the exposed planes of the lamellae resulting from the melt-drawn method are (200), which is consistent with results of transmission electron microscopy and electron diffraction. Because of the high degree of anisotropy in the sample, coming from alignment of the molecular chains along the drawing direction, the measured friction force, F, determined by FFM is strongly dependent on the angle, theta, between the scanning direction and the chain axis. The force increases as theta is increased from 0 degrees (i.e., parallel to the chain axis) to 90 degrees (i.e., perpendicular to the chain axis). The structural anisotropy was also found to strongly influence the measurements of the transverse chain modulus of the polymer by the nanoindentation technique. The measured value of 13.8 GPa with transverse modulus was larger than the value 4.3 GPa determined by wide-angle X-ray diffraction, which we attributed to anisotropic deformation of the lamellae during nanoindentation measurements that was not accounted for by the elastic treatment we adopted from Oliver and Pharr. The present approach using scanning probe microscopy has the advantage that direct correlations between the nanostructure, nanotribology, and nanomechanical properties of oriented samples can be determined simultaneously and simply.

Study of elastic modulus and yield strength of polymer thin films using atomic force microscopy

Nanometer-scale elastic moduli and yield strengths of polycarbonate (PC) and polystyrene (PS) thin films were measured with atomic force microscopy (AFM) indentation measurements. By analysis of the AFM indentation force curves with the method by Oliver and Pharr, Young's moduli of PC and PS thin films could be obtained as 2.2 +/- 0.1 and 2.6 +/- 0.1 GPa, respectively, which agree well with the literature values. By fitting Johnson's conical spherical cavity model to the measured plastic zone sizes, we obtained yield strengths of 141.2 MPa for PC thin films and 178.7 MPa for PS thin films, which are similar to2 times the values expected from the literature. We propose that it is due to the AFM indentation being asymmetric, which was not accounted for in Johnson's model. A correction factor, epsilon, of similar to0.72 was introduced to rescale the plastic zone size, whereupon good agreement between theory and experiment was achieved.

Experimental measurement of polyethylene chain modulus by scanning force microscopy

Nanoindentation technique and scanning force microscopy have been used to measure directly the polyethylene modulus along the chain axis. Single crystals of polyethylene were employed in order to obtain well-aligned chain segments. To minimize effects of scanner creep, a Z scan rate of 3 Hz was employed. The "X Rotate" value of 25 degrees was selected to eliminate effects of lateral tip motion. The results were analyzed by the Oliver -Pharr method for which direct observation and measurement of the contact area are not required. Considering the influence of tip roundness on the projected contact area, the nanoindentation results were analyzed by the Sawa method. The chain modulus obtained from the thinner polyethylene single crystal sample was 204 +/- 21 GPa by the Oliver-Pharr method and 168 +/- 17 GPa by the Sawa method. The lower values than expected were due to substrate effects and anisotropy of chain deformation during nanoindentation. An extrapolation of the chain modulus obtained by various strains to zero nanoindentation eliminated the effect of substrate and anisotropy of chain deformation. The corresponding chain modulus obtained from the thicker sample was 278 GPa by the Oliver-Pharr method and 267 GPa by the Sawa method, respectively, in better agreement with the value of 340 Cpa determined theoretically. (C) 2001 Elsevier Science Ltd. All rights reserved.

大气活性气态汞采样和分析方法

改进了利用镀KCl扩散管采集大气活性气态汞分析方法。实验证明：在450℃条件下加热10min 被扩散管捕获的活性气态汞会被热解出。该法最低检出限为3 pg，具有成本低、分析方法简单、省时及采样管能多次使用等优点。

Curso de nivelación para los alumnos de nuevo ingreso en la Escuela Universitaria de Arquitectura Técnica de la Universidad Politécnica de Madrid

En la Escuela Universitaria de Arquitectura Técnica de Madrid, se ha desarrollado un curso que cabe denominar de Nivelación. Incluyó un conjunto de actividades destinadas a lograr que los alumnos accedieran con éxito al mundo Universitario. Era un curso dirigido a los alumnos que una vez concluido el bachillerato y superadas las Pruebas de Acceso a Estudios Universitarios habían sido admitidos para cursar el primer curso de los estudios conducentes al título universi-tario oficial de Arquitecto Técnico. El curso ha sido impartido por profesores de la Escuela Universitaria de Arquitectura Técnica de la Universidad Politécnica de Madrid adscritos, respectivamente, a los Departamentos "EXPRE-SIÓN GRAFICA APLICADA A LA EDIFICACIÓN", "MATEMÁTICAS APLICADAS A LA ARQUITECTURA TÉCNICA" y "TECNOLOGÍA DE LA EDIFICACIÓN". Cada uno de los tres Departamentos concretó inicialmente las asignaturas y los temarios a des-arrollar sí bien a lo largo del proceso las enseñanzas se produjeron algunas modificaciones para una mejor adaptación del curso a las necesidades reales de los alumnos. En la ponencia se analizarán los avances y descubrimientos de los profesores en sus respectivos campos y se presentarán las conclusiones obtenidas así como las posibles modificaciones para futuras ediciones de cursos similares.

Functional genomic hypothesis generation and experimentation by a robot scientist

King R. D., Whelan, K. E., Jones, F. M., Reiser, P. G. K., Bryant, C. H., Muggleton, S., Kell, D. B. and Oliver, S. G. (2004) Functional genomic hypothesis generation and experimentation by a robot scientist. Nature 427 (6971) p247-252

Application of metabolomics to plant genotype discrimination using statistics and machine learning

Janet Taylor, Ross D King, Thomas Altmann and Oliver Fiehn (2002). Application of metabolomics to plant genotype discrimination using statistics and machine learning. 1st European Conference on Computational Biology (ECCB). (published as a journal supplement in Bioinformatics 18: S241-S248).

A novel breast tissue density classification framework

Oliver, A., Freixenet, J., Marti, R., Pont, J., Perez, E., Denton, E. R. E., Zwiggelaar, R. (2008). A novel breast tissue density classification framework. IEEE Transactions on Information Technology in BioMedicine, 12 (1), 55-65

Behaviour and rationality in corporate governance

Marnet, Oliver, 'Behaviour and rationality in corporate governance', Journal of Economic Issues (2005) 39(3) pp.613-632 RAE2008

History repeats itself: The failure of rational choice models in corporate governance

Marnet, Oliver, 'History repeats itself: The failure of rational choice models in corporate governance', Critical Perspectives on Accounting (2005) 18(2) pp.191-210 RAE2008

Intersubject Regularity in the Intrinsic Shape of Human V1

Previous studies have reported considerable intersubject variability in the three-dimensional geometry of the human primary visual cortex (V1). Here we demonstrate that much of this variability is due to extrinsic geometric features of the cortical folds, and that the intrinsic shape of V1 is similar across individuals. V1 was imaged in ten ex vivo human hemispheres using high-resolution (200 μm) structural magnetic resonance imaging at high field strength (7 T). Manual tracings of the stria of Gennari were used to construct a surface representation, which was computationally flattened into the plane with minimal metric distortion. The instrinsic shape of V1 was determined from the boundary of the planar representation of the stria. An ellipse provided a simple parametric shape model that was a good approximation to the boundary of flattened V1. The aspect ration of the best-fitting ellipse was found to be consistent across subject, with a mean of 1.85 and standard deviation of 0.12. Optimal rigid alignment of size-normalized V1 produced greater overlap than that achieved by previous studies using different registration methods. A shape analysis of published macaque data indicated that the intrinsic shape of macaque V1 is also stereotyped, and similar to the human V1 shape. Previoud measurements of the functional boundary of V1 in human and macaque are in close agreement with these results.