Estudo sobre o efeito dos parâmetros de processamento dos pós e sinterização do aço inox 316l reforçado com NbC

This masther dissertation presents a contribution to the study of 316L stainless steel sintering aiming to study their behavior in the milling process and the effect of isotherm temperature on the microstructure and mechanical properties. The 316L stainless steel is a widely used alloy for their high corrosion resistance property. However its application is limited by the low wear resistance consequence of its low hardness. In previous work we analyzed the effect of sintering additives as NbC and TaC. This study aims at deepening the understanding of sintering, analyzing the effect of grinding on particle size and microstructure and the effect of heating rate and soaking time on the sintered microstructure and on their microhardness. Were milled 316L powders with NbC at 1, 5 and 24 hours respectively. Particulates were characterized by SEM and . Cylindrical samples height and diameter of 5.0 mm were compacted at 700 MPa. The sintering conditions were: heating rate 5, 10 and 15◦C/min, temperature 1000, 1100, 1200, 1290 and 1300◦C, and soaking times of 30 and 60min. The cooling rate was maintained at 25◦C/min. All samples were sintered in a vacuum furnace. The sintered microstructure were characterized by optical and electron microscopy as well as density and microhardness. It was observed that the milling process has an influence on sintering, as well as temperature. The major effect was caused by firing temperature, followed by the grinding and heating rate. In this case, the highest rates correspond to higher sintering.

Estudo da sinterização de cavacos de aço ferritico

This research studies the sintering of ferritic steel chips from the machining process. Were sintered metal powder obtained from machining process chips for face milling of a ferritic steel. The chip was produced by machining and characterized by SEM and EDS, and underwent a process of high energy mill powder characterized also by SEM and EDS. Were constructed three types of matrixes for uniaxial compression (relation l / d greater than 2.5). The differences in the design of the matrixes were essentially in the direction of load application, which for cylindrical case axial direction, while for the rectangular arrays, the longer side. Two samples were compressed with different geometries, a cylindrical and rectangular with the same compaction pressure of 700 MPa. The samples were sintered in a vacuum resistive furnace, heating rate 20 °C / min., isotherm 1300 °C for 60 minutes, and cooling rate of 25 °C / min to room temperature. The starting material of the rectangular sample was further annealed up to temperature of 800 ° C for 30 min. Sintered samples were characterized by scanning electron microscopy, optical microscopy and EDS. The sample compressed in the cylindrical matrix did not show a regular density reflecting in the sintered microstructure revealed by the irregular geometry of the pores, characterizing that the sintering was not complete, reaching only the second phase. As for the specimen compacted in the rectangular array, the analysis performed by scanning electron microscopy, optical microscopy and EDS indicate a good densification, and homogeneous microstructure in their full extent. Additionally, the EDS analyzes indicate no significant changes in chemical composition in the process steps. Therefore, it is concluded that recycling of chips, from the processed ferritic steel is feasible by the powder metallurgy. It makes possible rationalize raw material and energy by manufacture of known properties components from chips generated by the machining process, being benefits to the environment

Estudo da adição de resíduo de scheelita em matriz cerâmica: formulação, propriedades físicas e microestrutura

Extractivism mineral is considered an activity highly degrading, due to the large volume of material that he moves in the form of ore and residues. The vast majority of mining companies do not show any technology or economically viable application that will allow the recycling of mineral residue, these being launched in areas receiving located the "open skies" degrade the environment. In Rio Grande do Norte to the production of ceramic red restricts their activities to the production of products such as: solid bricks, ceramic blocks, tiles, among others. Seeking to unite experiences and technical information that favor sustainable development, with important benefits to the construction sector and civil society in general, the present work studies the incorporation of the residue of scheelite in ceramic matrix kaolinitic, coming from the municipality of Boa Saúde - RN, in percentage of 5 %, 10 %, 20 %, 30% 40% and 50 %, by evaluating its microstructure, physical properties and formulation. The raw materials were characterized through the trials of X ray fluorescence, Diffraction of X rays, Differential Thermal Analysis and Termogravimetric Analysis. The samples were formed and fired at temperatures of 850o, 900o, 1000o, 1050o, 1100o, 1150o and 1200 oC, with isotherm of 1 hour and heating rate of 10 oC/min. Assays were performed technological of loss to fire, Water Absorption, Apparent Porosity, Apparent Density, Mass Loss in Fire and Bending Resistance; in addition to the Scanning Electron Microscopy, analyzing their physical and mechanical properties. The use of residue of scheelite in ceramic mass kaolinitic provided a final product with technological properties that meet the technical standards for the production of bricks and roofing tiles, with the percentage of 20% of waste that showed the best results

Avaliação da espécie vegetal Croton cajucara Benth como inibidor de biocorrosão em aço carbono Aisi 1020

Actually in the oil industry biotechnological approaches represent a challenge. In that, attention to metal structures affected by electrochemical corrosive processes, as well as by the interference of microorganisms (biocorrosion) which affect the kinetics of the environment / metal interface. Regarding to economical and environmental impacts reduction let to the use of natural products as an alternative to toxic synthetic inhibitors. This study aims the employment of green chemistry by evaluating the stem bark extracts (EHC, hydroalcoholic extract) and leaves (ECF, chloroform extract) of plant species Croton cajucara Benth as a corrosion inhibitor. In addition the effectiveness of corrosion inhibition of bioactive trans-clerodane dehydrocrotonin (DCTN) isolated from the stem bark of this Croton was also evaluated. For this purpose, carbon steel AISI 1020 was immersed in saline media (3,5 % NaCl) in the presence and absence of a microorganism recovered from a pipeline oil sample. Corrosion inhibition efficiency and its mechanisms were investigated by linear sweep voltammetry and electrochemical impedance. Culture-dependent and molecular biology techniques were used to characterize and identify bacterial species present in oil samples. The tested natural products EHC, ECF and DCTN (DMSO as solvent) in abiotic environment presented respectively, corrosion inhibition efficiencies of 57.6% (500 ppm), 86.1% (500 ppm) and 54.5% (62.5 ppm). Adsorption phenomena showed that EHC best fit Frumkin isotherm and ECF to Temkin isotherm. EHC extract (250 ppm) dissolved in a polar microemulsion system (MES-EHC) showed significant maximum inhibition efficiency (93.8%) fitting Langmuir isotherm. In the presence of the isolated Pseudomonas sp, EHC and ECF were able to form eco-compatible organic films with anti-corrosive properties

On the interaction of bovine serum albumin with ionic surfactants: Temperature induced EPR changes of a maleimide nitroxide reflect local protein dynamics and probe solvent accessibility

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Caracterização físico-química de complexo de inclusão entre hidroximetilnitrofurazona e hidroxipropil-beta-ciclodextrina

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

THE EFFECT of ANIONIC SORPTION on THE METAKAOLINITE

This paper reports an investigation on the effect of thermal activation of kaolinite. It is well known that during calcinations (400-650 degrees C), kaolinite loses the OH lattice water and is transformed into metakaolinite or amorphous material. Arsenic is trace element that is toxic to animals including humans. The adsorption of arsenic on kaolinite was investigated at varying pH and thermal pretreatment. Calcination of sample is carried out at 650 degrees C for 3 h. The decomposition of kaolinite is recorded using methods of thermal analysis. The resultant product is identified by XRD. Laboratory experiments were conducted examining the effect of arsenic by thermally modified kaolinite. The Langmuir isotherm was used to describe arsenite and arsenate sorption by the calcined kaolinite. The equilibrium parameters used were based on experimental data obtained for the dynamic adsorption process of arsenic. Removal of arsenate using natural kaolinite was satisfactory, whereas arsenic was not removed by adsorption with thermally modified kaolinite. Moreover, the adsorption of arsenic by kaolinite and metakaolinite decreases with increasing pH.

Computational analysis and physico-chemical characterization of an inclusion compound between praziquantel and methyl-beta-cyclodextrin for use as an alternative in the treatment of schistosomiasis

Schistosomiasis is still an endemic disease in many regions, with 250 million people infected with Schistosoma and about 500,000 deaths per year. Praziquantel (PZQ) is the drug of choice for schistosomiasis treatment, however it is classified as Class II in the Biopharmaceutics Classification System, as its low solubility hinders its performance in biological systems. The use of cyclodextrins is a useful tool to increase the solubility and bioavailability of drugs. The aim of this work was to prepare an inclusion compound of PZQ and methyl-beta-cyclodextrin (MeCD), perform its physico-chemical characterization, and explore its in vitro cytotoxicity. SEM showed a change of the morphological characteristics of PZQ:MeCD crystals, and IR data supported this finding, with changes after interaction with MeCD including effects on the C-H of the aromatic ring, observed at 758 cm(-1). Differential scanning calorimetry measurements revealed that complexation occurred in a 1:1 molar ratio, as evidenced by the lack of a PZQ transition temperature after inclusion into the MeCD cavity. In solution, the PZQ UV spectrum profile in the presence of MeCD was comparable to the PZQ spectrum in a hydrophobic solvent. Phase solubility diagrams showed that there was a 5.5-fold increase in PZQ solubility, and were indicative of a type A(L) isotherm, that was used to determine an association constant (K(a)) of 140.8 M(-1). No cytotoxicity of the PZQ:MeCD inclusion compound was observed in tests using 3T3 cells. The results suggest that the association of PZQ with MeCD could be a good alternative for the treatment of schistosomiasis.

Estimativa de parâmetros genéticos da habilidade de permanência aos 48, 60 e 72 meses de idade em vacas da raça Caracu

Objetivou-se estimar a herdabilidade da característica habilidade de permanência (HP) em um rebanho de bovinos da raça Caracu visando sua utilização como critério de seleção. A característica em estudo foi definida como a probabilidade de a vaca estar presente no rebanho aos 48 (HP48), aos 60 (HP60) e aos 72 (HP72) meses, desde que possuíssem registros de pelo menos duas lactações nas específicas idades. Observações binárias, com zero (0 = fracasso) e um (1 = sucesso) foram designadas aos animais. Para análise da HP, foram utilizados dados de 5.487, 4.947 e 4.308 animais aos 48, 60 e 72 meses, respectivamente. Os componentes de variância e as herdabilidades foram estimados mediante inferência Bayesiana, via amostragem de Gibbs, pelo programa MTGSAM - threshold, utilizando-se um modelo touro. Foram utilizadas como variáveis explanatórias grupo de contemporâneos, classe de produção de leite na primeira lactação, classe de idade ao primeiro parto e sua interação. As análises forneceram estimativas médias de herdabilidade iguais a 0,28 ± 0,07 para HP48, 0,27 ± 0,07 para HP60 e 0,23 ± 0,07 para HP72. Os resultados evidenciaram que a característica HP apresentou variação aditiva em todas as idades estudadas e, portanto, pode ser empregada como critério de seleção para longevidade produtiva.

Dispersões sólidas de sinvastatina: preparação, caracterização, no estado sólido utilizando técnicas emergentes e estudo de estabilidade

This thesis aimed to assess the increase in solubility of simvastatin (SINV) with solid dispersions using techniques such as kneading (MA), co-solvent evaporation (ES), melting carrier (FC) and spray dryer (SD). Soluplus (SOL), PEG 6000 (PEG), PVP K-30 (PVP) e sodium lauryl sulphate (LSS) were used as carriers. The solid dispersions containing PEG [PEG-2(SD)], Soluplus [SOL-2(MA)] and sodium lauryl sulphate [LSS-2(ES)] were presented with a greater increase in solubility (5.02, 5.60 and 5.43 times respectively); analyses by ANOVA between the three groups did not present significant difference (p<0.05). In the phase solubility study, the calculation of the Gibbs free energy (ΔG) revealed that the spontaneity of solubilisation of SINV occurred in the order SOL>PEG >PVP 75%>LSS, always 80%. The phase diagrams of PEG and LSS presented solubilization stoichiometry of type 1:1 (type AL). The diagrams with PVP and SOL tend to 1:2 stoichiometry (type AL + AP). The stability coefficients (Ks) of the phase diagrams revealed that the most stable reactions occurred with LSS and PVP. The solid dispersions were characterized by Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), particle size distribution (PSD), near-infrared spectroscopy imaging (NIR-CI) and X-ray diffraction of the powder using the Topas software (PDRX-TOPAS). The solid dispersion PEG-2(SD) presented the greatest homogeneity and the lowest degree of crystallinity (18.2%). The accelerated stability study revealed that the solid dispersions are less stable than SINV, with PEG-2(SD) being the least stable, confirmed by FTIR and DSC. The analyses by PDRX-TOPAS revealed the amorphous character of the dispersions and the mechanism of increasing solubility

Testicular traits as selection criteria for young Nellore bulls

The objective of this study was to evaluate the possible use of biometric testicular traits as selection criteria for young Nellore bulls using Bayesian inference to estimate heritability coefficients and genetic correlations. Multitrait analysis was performed including 17,211 records of scrotal circumference obtained during andrological assessment (SCAND) and 15,313 records of testicular volume and shape. In addition, 50,809 records of scrotal circumference at 18 mo (SC18), used as an anchor trait, were analyzed. The (co) variance components and breeding values were estimated by Gibbs sampling using the Gibbs2F90 program under an animal model that included contemporary groups as fixed effects, age of the animal as a linear covariate, and direct additive genetic effects as random effects. Heritabilities of 0.42, 0.43, 0.31, 0.20, 0.04, 0.16, 0.15, and 0.10 were obtained for SC18, SCAND, testicular volume, testicular shape, minor defects, major defects, total defects, and satisfactory andrological evaluation, respectively. The genetic correlations between SC18 and the other traits were 0.84 (SCAND), 0.75 (testicular shape), 0.44 (testicular volume), -0.23 (minor defects), -0.16 (major defects), -0.24 (total defects), and 0.56 (satisfactory andrological evaluation). Genetic correlations of 0.94 and 0.52 were obtained between SCAND and testicular volume and shape, respectively, and of 0.52 between testicular volume and testicular shape. In addition to favorable genetic parameter estimates, SC18 was found to be the most advantageous testicular trait due to its easy measurement before andrological assessment of the animals, even though the utilization of biometric testicular traits as selection criteria was also found to be possible. In conclusion, SC18 and biometric testicular traits can be adopted as a selection criterion to improve the fertility of young Nellore bulls.

Genetic parameter estimates for buffalo milk yield, milk quality and mozzarella production and Bayesian inference analysis of their relationships

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Bayesian inference in genetic parameter estimation of visual scores in Nellore beef-cattle

The aim of this study was to estimate the components of variance and genetic parameters for the visual scores which constitute the Morphological Evaluation System (MES), such as body structure (S), precocity (P) and musculature (M) in Nellore beef-cattle at the weaning and yearling stages, by using threshold Bayesian models. The information used for this was gleaned from visual scores of 5,407 animals evaluated at the weaning and 2,649 at the yearling stages. The genetic parameters for visual score traits were estimated through two-trait analysis, using the threshold animal model, with Bayesian statistics methodology and MTGSAM (Multiple Trait Gibbs Sampler for Animal Models) threshold software. Heritability estimates for S, P and M were 0.68, 0.65 and 0.62 (at weaning) and 0.44, 0.38 and 0.32 (at the yearling stage), respectively. Heritability estimates for S, P and M were found to be high, and so it is expected that these traits should respond favorably to direct selection. The visual scores evaluated at the weaning and yearling stages might be used in the composition of new selection indexes, as they presented sufficient genetic variability to promote genetic progress in such morphological traits.

Análise genética de escores de avaliação visual de bovinos com modelos bayesianos de limiar e linear

O objetivo deste trabalho foi comparar as estimativas de parâmetros genéticos obtidas em análises bayesianas uni-característica e bi-característica, em modelo animal linear e de limiar, considerando-se as características categóricas morfológicas de bovinos da raça Nelore. Os dados de musculosidade, estrutura física e conformação foram obtidos entre 2000 e 2005, em 3.864 animais de 13 fazendas participantes do Programa Nelore Brasil. Foram realizadas análises bayesianas uni e bi-características, em modelos de limiar e linear. de modo geral, os modelos de limiar e linear foram eficientes na estimação dos parâmetros genéticos para escores visuais em análises bayesianas uni-características. Nas análises bi-características, observou-se que: com utilização de dados contínuos e categóricos, o modelo de limiar proporcionou estimativas de correlação genética de maior magnitude do que aquelas do modelo linear; e com o uso de dados categóricos, as estimativas de herdabilidade foram semelhantes. A vantagem do modelo linear foi o menor tempo gasto no processamento das análises. Na avaliação genética de animais para escores visuais, o uso do modelo de limiar ou linear não influenciou a classificação dos animais, quanto aos valores genéticos preditos, o que indica que ambos os modelos podem ser utilizados em programas de melhoramento genético.

Estimativas de correlações genéticas entre escores visuais e características de carcaça medidas por ultrassonografia em bovinos Nelore utilizando modelos bayesianos linear-limiar

O objetivo neste estudo foi estimar as correlações genéticas entre escores visuais e características de carcaça medidas por ultrassonografia em bovinos da raça Nelore utilizando a estatística bayesiana por meio da Amostragem de Gibbs, sob modelo animal linear-limiar. Foram estudadas as características categóricas morfológicas de musculosidade, estrutura física, conformação e sacro, avaliadas aos 15 e 22 meses de idade. Para as características de carcaça, foram avaliadas as características área de olho-de-lombo, espessura de gordura subcutânea, espessura de gordura subcutânea na garupa e altura na garupa. Os escores visuais devem ser empregados como critérios de seleção para aumentar o progresso genético para a característica área de olhode-lombo e, consequentemente, melhorar o rendimento de carcaça. As estimativas de correlação genética obtidas para musculosidade com espessura de gordura subcutânea e espessura de gordura subcutânea na garupa indicaram que a seleção para musculosidade pode levar a animais com melhor acabamento de carcaça. A seleção para a estrutura física e conformação aos 15 e 22 meses de idade pode promover resposta correlacionada para o aumento da altura na garupa.