942 resultados para Difference Between Generation X and Y Employees
Resumo:
Tanomaru-Filho M, Silveira GF, Reis JMSN, Bonetti-Filho I, Guerreiro-Tanomaru JM. Effect of compression load and temperature on thermomechanical tests for gutta-percha and Resilon (R). International Endodontic Journal, 44, 1019-1023, 2011.Aim To analyse a method used to evaluate the thermomechanical properties of gutta-percha and Resilon at different temperatures and compression loads.Methodology Two hundred and seventy specimens measuring 10 mm in diameter and 1.5 mm in height were made from the following materials: conventional gutta-percha (GCO). thermoplastic gutta-percha (GTP) and Resilon (R) cones (RE). After 24 h, the specimens were placed in water at 50 degrees C. 60 degrees C or 70 degrees C for 60 s. After that, specimens were placed between two glass slabs, and loads weighing 1.0, 3.0 or 5.0 kg were applied. Images of the specimens were digitized before and after the test and analysed using imaging software to determine their initial and final areas. The thermomechanical property of each material was determined by the difference between the initial and final areas of the specimens. Data were subjected to ANOVA and SNK tests at 5% significance. To verify a possible correlation between the results of the materials, linear regression coefficients (r) were calculated.Results Data showed higher flow area values for RE under all compression loads at 70 degrees C and under the 5.0 kg load at 60 degrees C (P < 0.05). Regarding gutta-percha, GTP showed higher flow under loads weighing 3.0 and 5.0 kg. at 60 and 70 degrees C (P < 0.05). GCO presented higher flow at 70 degrees C with a load of 5.0 kg. Regression analyses showed a poor linear correlation amongst the results of the materials under the different experimental conditions.Conclusion Gutta-percha and Resilon (R) cones require different compression loads and temperatures for evaluation of their thermomechanical properties. For all materials, the greatest flow occurred at 70 degrees C under a load of 5.0 kg: therefore. these parameters may be adopted when evaluating endodontic tilling materials.
Resumo:
The impact of shrimp fisheries in tropical regions has become comparable to the world's most intensively exploited temperate shed ecosystems. The increase in the fishing fleet in south-eastern Brazil and the decrease in landings of profitable shrimp species have contributed to the incorporation of additional species into those fisheries. The goal of the present study is to investigate the influence of environmental factors on the abundance patterns of shrimp communities on the south-eastern coast of Brazil, over a period of two years. Monthly collections were conducted in the Ubatuba and Caraguatatuba regions using a commercial shrimp fishing boat equipped with 'double-rig' nets. Each region was divided into 7 sampling stations up to 35 m deep. The relationship between the environmental factors and the abundance patterns in the shrimp communities was assessed using a canonical correlation analysis (CCorrA). The first set of variables used during the CCorrA included environmental characteristics and the second set of variables the abundance of the studied species. A total of 374,915 individuals were collected during the present study. Xiphopenaeus kroyeri showed the highest abundance (273,127), followed by Artemesia longinaris (73,422), and Pleoticus muelleri (15,262). In the first root, depth and temperature showed the highest factor loadings (0.9 and -0.7) and canonical weights (0.6 and -0.4). These environmental factors were strongly associated with the abundance of X. kroyeri (factor loading = - 0.9 and canonical weight = - 0.9). The second root demonstrated a positive relationship between abundance of P. muelleri and depth, and an inverse association with bottom temperature. The abundance patterns of X. kroyeri and P. muelleri were strongly affected by the water mass South Atlantic Central Water (cold waters =15 degrees C), which can lead to a temperature decrease in deeper areas (> 15 m). Thus, the opposite abundance trend for depth of these species might reflect bathymetric variation in temperature, a clear example of distinct behavioural differences of species of different origins, either tropical (X. kroyeri) or subantarctic (P. muelleri). The low overall association between environmental parameters and shrimp abundance patterns indicates that each studied species might have responded idiosyncratically to environmental variation, such that a general community-level response was not apparent. However, other confounding factors such as intraspecific migration patterns might have also played a role in generating the observed patterns.
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)
Resumo:
Objective To investigate the relationship between skipping meals and biochemical variables in obese children and adolescents.Study design The sample was composed of 174 obese children and adolescents, aged between 6 and 16 years (80 male and 94 female). Body composition was assessed by dual-energy x-ray absorptiometry, fasting blood glucose, and lipid profile were measured after 12 hours fasting. The frequency of skipping breakfast, lunch, or dinner was assessed through a face-to-face interview carried out with the parents.Results The prevalence of eating breakfast daily was low in boys (47.5%) and girls (44.7%). A higher frequency of eating breakfast was negatively correlated with glucose (r = -0.16; P = .026), triglycerides (r = -0.19; P = .011), and very low density lipoprotein cholesterol (r = -0.21; P = .005). In the multivariate model, the weekly frequency of eating breakfast remained negatively associated with glucose (beta = -0.975; P = .017), triglycerides (beta = -7.792; P = .017), and very low density lipoprotein cholesterol (beta = -1.870; P = .009) independent of age, sex, trunk fatness, and parents' education.Conclusion Skipping meals, mainly breakfast, is associated with glucose and lipid levels in obese children and adolescents. (J Pediatr 2012;161:871-4).
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
One of the models proposed for the origin of ultra high energy cosmic rays (UHECR's) suggests that these events are the decay products of relic superheavy metastable particles, which we call S particles. These particles can be produced in the reheating period following the inflationary epoch of the early Universe. We study this possibility and obtain constraints on some parameters such as the lifetime and direct couplings of the X-particle to the inflaton field from the requirement that they are responsible for the observed UHECR flux.
Resumo:
First measurements of the differential cross sections d(3)sigma/(dp(T)(gamma)dy(gamma)dy(jet)) for the inclusive production of a photon in association with a heavy quark (b, c) jet are presented, covering photon transverse momenta 30 < p(T)(gamma)< 150 GeV, photon rapidities |y(gamma)|< 1.0, jet rapidities |y(jet)|< 0.8, and jet transverse momenta p(T)(jet)> 15 GeV. The results are based on an integrated luminosity of 1 fb(-1) in pp collisions at s=1.96 TeV recorded with the D0 detector at the Fermilab Tevatron Collider. The results are compared with next-to-leading order perturbative QCD predictions.
Resumo:
In this work structural features of anionic microemulsions, containing the pharmaceutical biocompatible components soya phosphatidylcholine (SPC), eumulgin HRE 40 (EU) and sodium oleate (SO) as surfactant, cholesterol (CHO) as oil phase and aqueous buffer were studied. Microemulsions were formulated with and without the antitumor drug doxorubicin (DOX). The various microstructures characterized in the pseudo-temary phase diagram were analyzed by polarized light microscopy, small-angle X-ray scattering (SAXS) and X-ray diffraction (XRD) as well as by their ability to incorporate and release DOX. The experimental results demonstrated a correlation between the composition, the structural features and drug delivery. It was found that at higher cholesterol contents, the crystallization of CHO polymorph phases changed the mobility of DOX molecules. Droplets were formed with short-range spatial correlation from a microemulsion (ME) with a low surfactant:oil ratio. More ordered structures with lamellar arrangements formed by the increasing of the CHO proportions in the formulation may be due to CHO crystallization. The in vitro release of DOX showed that the presence of a high content of crystalline CHO prolongs the release of DOX from ME. The retention of DOX in the internal oil phase of the ME may modulate the drug release for a prolonged time. These results clearly demonstrate the potential of ME as a drug-delivery system. (c) 2007 Elsevier B.V. All rights reserved.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
The sol-gel method combined with a spin-coating technique has been successfully applied for the preparation of rare-earth doped silica:germania films used for the fabrication of erbium-doped waveguide amplifiers (EDWA), presenting several advantages over other methods for the preparation of thin films. As with other methods, the sol-gel route also shows some drawbacks, such as cracks related to the thickness of silica films and high hydrolysis rate of certain precursors such as germanium alkoxides. This article describes the preparation and optical characterization of erbium and ytterbium co-doped SiO2:GeO2 crack-free thick films prepared by the sol-gel route combined with a spin-coating technique using a chemically stable non-aqueous germanium oxide solution as an alternative precursor. The non-crystalline films obtained are planar waveguides exhibiting a single mode at 1,550 nm with an average thickness of 3.9 mu m presenting low percentages of porosity evaluated by the Lorentz-Lorenz Effective Medium Approximation, and low stress, according to the refractive index values measured in both transversal electric and magnetic polarizations. Weakly confining core layers (0.3% < Delta n < 0.75%) were obtained according to the refractive index difference between the core and buffer layers, suggesting that low-loss coupling EDWA may be obtained. The life time of the erbium I-4(13/2) metastable state was measured as a function of erbium concentration in different systems and based on these values it is possible to infer that the hydroxyl group was reduced and the formation of rare-earth clusters was avoided.
Resumo:
OBJETIVO: revisar a literatura mais atual, dos últimos 15 anos, em busca de estudos clínicos que relatem a relação entre a disfunção temporomandibular (DTM) e o tratamento ortodôntico e/ou a má oclusão. A intenção foi verificar se o tratamento ortodôntico aumentaria o aparecimento de sinais e sintomas de DTM, e se o tratamento ortodôntico seria um recurso para o tratamento ou prevenção dos sinais e sintomas de DTM. MÉTODOS: artigos dos tipos revisão de literatura, editorial, carta, estudo experimental em animais e comunicação foram excluídos dessa revisão. Foram incluídos artigos prospectivos, longitudinais, caso-controle ou retrospectivo com amostra maior, com relevante análise estatística. Estudos que abordassem deformidades e síndromes craniofaciais e tratamento por cirurgia ortognática também foram excluídos, bem como aqueles que relatassem apenas a associação entre má oclusão e DTM. RESULTADOS: foram encontrados 20 artigos relacionando Ortodontia à DTM, segundo os critérios adotados. Os estudos, então, associando sinais e sintomas de DTM ao tratamento ortodôntico apresentaram resultados heterogêneos. Alguns encontraram efeitos positivos do tratamento ortodôntico para os sinais e sintomas de DTM; entretanto, nenhum deles apresentou diferença estatisticamente significativa. CONCLUSÕES: todos os estudos citados nessa revisão de literatura relataram que o tratamento ortodôntico não forneceu risco ao desenvolvimento de sinais e sintomas de DTM, independentemente da técnica utilizada para tratamento, da exodontia ou não de pré-molares e do tipo de má oclusão previamente apresentada pelo paciente. Alguns estudos realizados com acompanhamento em longo prazo concluíram que o tratamento ortodôntico não seria preventivo ou uma modalidade de tratamento para DTM.
Resumo:
Purpose: To evaluate the bond strength between human dentin and composites, using two light-activated single-bottle total-etch adhesive systems with different pHs combined with chemically activated and light-activated-composites. The tested hypothesis was that the dentin bond strength is not influenced by an adhesive system of low pH, combined with chemically activated or light-activated composites. Material and Method: Flat dentin surfaces of twenty-eight human third molars were allocated in 4 groups (n=7), depending on the adhesive system: (One Step Plus-OS and Prime & Bond NT-PB) and composite (light-activated Filtek Z-100 [Z100] and chemically activated Bisfil 2B [B2B]). Each adhesive system was applied on acid-etched dentin and then one of the composites was added to form a 5 mm-high resin block. The specimens were stored in tap water (37 degrees C/24 h) and sectioned into two axes, x and y. This was done with a diamond disk under coolant irrigation to obtain beams with a cross-section area of approximately 0.8 mm(2). Each specimen was then attached to a custom-made device and submitted to the microtensile test (1 mm.min(-1)). Data were analyzed using two-way ANOVA and Tukey's tests (p<0.05). Results: the anticipated hypothesis was not confirmed (p<0.0001). The bond strengths (MPa) were not statistically different between the two adhesive systems when light-activated composite was used (OS+Z100 = 24.7 +/- 7.1(a); PB+Z100 = 23.8 +/- 5.7(a)). However, with use of the chemically activated composite (B2B), PB (7.8 +/- 3.6(b) MPa) showed significantly lower dentin bond strengths than OS (32.2 +/- 7.6(a)). Conclusion: the low pH of the adhesive system can affect the bond of chemically activated composite to dentin. on the other hand, under the present conditions, the low pH did not seem to affect the bond of light-activated composites to dentin significantly.
Resumo:
In this letter, the authors propose that photoluminescence emission in CaTiO3 is affected not only by disorder in the lattice former but also by structural disorder in the lattice modifier. Structural disorder was evaluated by Ti, Ca K-edge x-ray absorption near-edge structure experiments and by photoluminescence emission. The preedge feature of the Ca K edge was related to the intensity of photoluminescence emission. The results of the preedge feature of the Ca K-edge x-ray absorption near-edge structure confirm the presence of different Ca coordination numbers, namely, Ca-O-11 and Ca-O-12. (c) 2007 American Institute of Physics.
Resumo:
We describe a new physicochemical descriptor of the antioxidant activity of phenols, the energy difference between the two highest occupied molecular orbitals, which we believe will improve quantitative structure-activity relationship studies about these compounds. (C) 2003 Wiley Periodicals, Inc.
Resumo:
The binding of the cations thallium(I), calcium(II) and terbium(III) to methyl methacrylate-methacrylic acid copolymers with different fractions of acid groups (x) has been studied in aqueous solution at, various pH values using the fluorescence of covalently bonded 9-vinyl anthracene as a probe. In all cases, the extent of binding increases as a function of the charge of the polymer with either increasing fraction of carboxylic acids or of pH. However, differences are observed in the behavior of the three cations, With Tl(I), quenching of the anthracene group fluorescence is observed. indicating that the thallium(I) approaches the probe and suggesting that the alkylanthracene is probably in a relatively polar region. Binding constants have been determined from anthracene quenching data and from studies with the fluorescent-probe sodium pyrenetetrasulfonate, Good agreement is obtained between the two methods, and values for the binding constants increase from 250 to 950 M-1 as x increases from 0.39 to 1. It is suggested that the cation is held in the polyelectrolyte domain, partly by Debye-Huckel effects and partly by more specific interactions. Stronger binding is found with calcium(II) and terbium(III), and in this case increases in fluorescence intensity are observed on complexation due to the anthracene group being in a more hydrophobic region, probably as a result of conformational changes in the polymer chain. In the former case the stoichiometry of the interaction was determined from the fluorescence data to involve two carboxylate groups bound per calcium. Association constants were found using murexide as an indicator of free calcium to vary from 8400 to 37 000 M-1 as x increases from 0.39 to 1. It is suggested that in this case specific calcium(II)-carboxylate interactions contribute to the binding. With terbium(III), a greater increase in the probe fluorescence intensity was observed than with calcium, and it is suggested that the interaction with the polymer is even stronger, leading to a more pronounced conformational change in the polymer. It is proposed that the terbium(III) interacts with sis carboxylic groups on the polymer chain, with three being coordinated and three attracted by electrostatic interactions.