Influence of addition of calcium oxide on physicochemical properties of Portland cement with zirconium or niobium oxide

Context: Calcium oxide (CaO) may be added to mineral trioxide aggregate (MTA) or Portland cement (PC) to improve physicochemical and biological properties. Aims: To evaluate the physicochemical properties of PC associated with radiopacifiers and CaO. Materials and Methods: MTA Angelus, PC + 30% zirconium oxide (Zr), or 30% niobium oxide (Nb) associated with 10 or 20% of CaO were evaluated. Gilmore needles were used to evaluate initial and final setting time. Compressive strength was evaluated after the periods of 24 hours and 21 days. pH was analyzed after 3, 12, 24 hours, 7, 14, 21 days. Solubility and flow tests were performed based on the ISO 6876. The data obtained were submitted to analysis of variance and Tukey tests (P ≤ 0.05). Results: The associations with 10% CaO showed greater strength that the associations with 20% CaO. The shortest initial setting time was observed for the association PC + Zr + 20% CaO and MTA. All the cements presented alkaline pH. The flow of all cements was similar. The highest solubility was found in the associations with 20% CaO. Conclusion: The addition of CaO to PC favored the alkaline property and the PC + Zr + 20% CaO presented setting time similar to MTA.

Influence of the gutta-percha taper and finger spreader on lateral consensation effectiveness

Introduction: Lateral condensation effectiveness may be influenced by the gutta-percha and finger spreader taper used during root canal obturation. Objective: To evaluate the penetration ability of finger spreader into simulated root canals prepared using MTwo rotary system and filled with different gutta-percha and finger spreader tapers. Material and methods: Resin blocks with curved root canals had the apical diameter enlarged up to #25.06 and distributed into groups (n = 6) according to the gutta-percha taper (#25.02, #25.04, and #25.06) and the finger spreader (#30 and #35 NiTi, and stainless steel B) used to perform cold lateral condensation. After applying a load of 1.5 Kg over the finger spreaders’ head, the distance between the finger spread tip and the apical limit of the root canal preparation were obtained. The data were submitted to Anova and Tukey-Krammer’s test, with 5% of significance. Results: The gutta-percha cones with 0.02 taper enabled higher finger spreader penetration when compared to 0.04 and 0.06 tapers (p < 0.05), which were similar between each other (p > 0.05), regardless of the type and diameter of the finger spreader used. When different finger spreaders were compared among themselves, stainless steel B showed higher penetration ability (p < 0.05). Conclusion: It was concluded that the stainless-steel finger spreaders showed superior penetration ability and gutta-percha with lower tapers enabled a more effective lateral condensation at the apical third.

MTA versus Portland cement: review of literature

Introduction: Both Mineral Trioxide Aggregate (MTA) and Portland cement (PC) have been highlighted because of their favorable biological properties, with extensive applications in Endodontics, including the possibility of using into root canal filling. Objective: This article reviews literature related to MTA and PC comparing their physical, chemical and biological properties, as well as their indications. Literature review: Literature reports studies revealing the similarities between these materials’ properties, including both biocompatibility and bone repair induction. Moreover, there is the need for the development of a root canal sealer based on these materials (MTA and PC). Conclusion: MTA and CP show promissory perspective both in Dentistry and Endodontics.

A new calcium silicate-based material (Biodentine) for filling radicular perforation in an endodontic-periodontal lesion: a case report

This case report presents an apical radicular perforation management using new calcium silicate-based cement (Biodentine) in a combined endodontic-periodontal lesion. The presence of apical radicular perforation may interfere in the endodontic treatment prognosis. Radicular perforation filling with bioactive cement through endodontic surgery is a possible treatment. This study presents an apical radicular perforation with periodontal involvement, due to alveolar bone loss on the buccal radicular surface from an incorrect intracanal preparation for the fiber post placing. The chosen alternative was a periapical surgery, the perforation was filled with a silicate and calcium chloride bioactive cement (Biodentine; Septodont, Saint-Maur-des-Fosses Cedex, France), and the radicular surface was etched with citric acid, because the access from root canal was impossible. The follow-up was for 8 months, through clinical and radiographic analysis. At the end of the follow-up, radiographic analyses showed the bone healing, and no clinical changes in periodontal probing depth, gingival recession, and the height of the interproximal mesial and distal papillae were observed. The root perforation treatment has a difficult management, especially when the dental root has a simultaneous periodontal commitment. The Biodentine proves to be a promising material for use in these situations.

Capacidade de termoplastificação da guta-percha com diferentes conicidades

jObjective: The objective of this study was to evaluate the thermoplasticity of the gutta-percha cones used for root canal obturation: Dentsply convencional (Dentsply Ind. e Com., Petrópolis, RJ, Brazil), Dentsply 0.04, (Dentsply Ind. e Com., Petrópolis, RJ, Brazil), Antaeos 0.04 (VDW GmbH, Munich, Germany), ProTaper (Dentsply Ind. e Com., Petrópolis, RJ, Brazil) and Alfa 0.06 (VDW GmbH, Munich, Germany). Material and method: Specimens of each material (n = 10) were prepared after heating. After 24 hours were again heated to 70 °C and placed between two glass plates and subjected to a compression of 5 kg for 2 minutes. The scanned image of the groups before and after the compression was analyzed with the software Image Tool (UTHSCSA Image Tool for Windows version 3.0, San Antonio, TX, USA). The flow capacity of the different materials was determined by the difference between the initial and final area of each specimen. The results were submitted to ANOVA and Tukey test with significance level of 5%. Result: Among the material evaluated, the gutta-percha cones Alpha 0.06 and ProTaper presented more thermoplasticity than other groups (p < 0.05). The Dentsply gutta-percha presented thermoplasticity intermediate. The groups Dentsply 0.04 and 0.04 showed lower thermoplasticity after heating (p > 0.05). Conclusion: The gutta-percha present different property of thermoplasticity, which is important to selection of thermoplastic obturation techniques.

Ação solvente do salicilato de metila sobre resilon e guta-percha

Objective: The aim of this study was to evaluate the action of methyl salicylate in dissolving Resilon and gutta-percha. Material and method: Ten discs of Resilon, Alpha gutta-percha and ProTaper gutta-percha were prepared (10 mm diameter × 1 mm thick) and kept at 37 °C for 48 hours. Each sample was weighed in a balance of accuracy determining the initial mass. The specimens were immersed in methyl salicylate or xylene (control) for 5  minutes, rinsed in water for 30 minutes, dried and subsequently weighed in 24 hours intervals until the stabilization of weight (final mass). The solvent capacity was expressed by the difference between the final and initial mass. The data were analyzed by using ANOVA and Tukey test with significance level of 5%. Result: The results showed that the methyl salicylate was more effective on Resilon than on gutta-percha (p < 0.05). Methyl salicylate and xylene had similar solvent action on Resilon (p > 0.05). The xylene showed better performance on gutta-percha than methyl salicylate (p < 0.05). Conclusion: It was concluded that methyl salicylate did not show solvent action on gutta-percha, however it showed effectiveness in dissolution of Resilon. Thus methyl salicylate can be a possible alternative to the use of xylene during endodontic retreatment of teeth obturated with Resilon.

Cirugía endodóntica con obturación simultánea del conducto radicular: caso atípico

The apical surgery with simultaneous root filling consists in the elimination of the local etiologic factors concomitant with the shaping and obturation of the root canal system. This technique is indicated when there is no possibility of obturating the root canal by conventional methods. Some adverse factors may difficult the clinical procedures, such as the radiographic interpretation. Periapical radiographs must not be used as the main diagnostic resource due to their inherent disadvantages, such as distortion and superimposition with other anatomical structures. The aim of this clinical case report is to show the limitations of radiographic examination in an apical surgery in which a root perforation was not visible in the radiographic image, as well as the gutta-percha was not related to its real clinical location.

Diagnóstico radiográfico diferencial das reabsorções radiculares internas e externas entre especialistas em endodontia e clínicos gerais

Objectives: The objective of this study was to evaluate the ability of endodontists and general practioners to perform the differential radiographic diagnosis between internal and external root resorptions, using digitized periapical radiographs. Methods: Thirty periapical radiographic images of external and internal resorption were selected. The evaluators were comprised of 15 endodontists and 29 general practitioners who answered a questionnaire with the following question: “What type of resorption in the following radiographics do you diagnose?” (1) Inflammatory external root resorption. (2) Internal root resorption. Statistical analysis was performed based on the Mann-Whitney test, with significance level of 5%. Results: There was no statistically significant difference in the percentage of correct answers from specialists in endodontics and general practitioners. Conclusions: Both groups demonstrated satisfactory skill in the radiographic interpretation of internal and external resorption and there was a higher percentage of correct diagnosis of internal resorption than the external.

Actividad antimicrobiana de la solución de nanopartícula de plata en cultivo de Enterococcus faecalis

Objective. The objective of this study was to evaluate the antimicrobial activity of the silver nanoparticles solution in enterococcus faecallis cultures (ATCC 29212), compared with various solutions of sodium hypoclorithe (NaOCl). Material and methods. Five Agar Petri plates were inoculated with E. faecallis and each of them was placed a cellulose dish embedded with silver nanoparticles solution, or a solution of sodium hypochlorite evaluated (Viarzon, Cloralex, Clorox). Chlorhexidine digluconate 2% was used as positive control and sterile saline solution was used as negative control. After 24 hours of incubation at 37ºc, under aerobic conditions, the zones of inhibition of bacterial growth were measured and the results subjected to the statistical t test among the experimental groups (= 5%). Results. The Cloralex showed to be the most effective reflected in the extent of inhibition in relation to other substances (p< 0.05), except that the chlorhexidine digluconate 2% (p> 0.05). The solution of silver nanoparticles provided a greater zone of inhibition than the sodium hypochlorite solution (Clorox) and Viarzon (p< 0.05). Clorox and Viarzon didn't provide zones of inhibition and were similar to each other (p> 0.05). Conclusions. The solution of silver nanoparticles presents antimicrobial activity in cultured E. faecallis, even higher than other commercial forms of sodium hypochlorite. Further studies should be carried out to determine its viability as irrigating solution in endodontics (AU)

Effectiveness of several solutions to prevent the formation of precipitate due to the interaction between sodium hypochlorite and chlorhexidine and its effect on bond strength of an epoxy-based sealer

To evaluate the effectiveness of isopropyl alcohol, saline or distilled water to prevent the precipitate formed between sodium hypochlorite (NaOCl) and chlorhexidine (CHX) and its effect on the bond strength of an epoxy-based sealer in radicular dentine. Methodology The root canals of 50 extracted human canines (n = 10) were instrumented. In G1, root canals were irrigated with 17% EDTA and 2.5% NaOCl; G2, as G1, except that 2% CHX was used as the final irrigant. In the other groups, intermediate flushes with isopropyl alcohol (G3), saline (G4) or distilled water (G5) were used between NaOCl and CHX. The specimens were submitted to SEM analysis to evaluate the presence of debris and smear layer, in the apical and cervical segments. In sequence, fifty extracted human canines were distributed into five groups (n = 10), similar to the SEM study. After root filling, the roots were sectioned transversally to obtain dentine slices, in the cervical, middle and apical thirds. The root filling was submitted to a push-out bond strength test using an electromechanical testing machine. Statistical analysis was performed using Kruskal–Wallis and Dunn's tests (α = 5%). Results All groups had similar amounts of residue precipitated on the canal walls (P > 0.05). The push-out bond strength values were similar for all groups, independently of the root third evaluated (P > 0.05). Conclusions Isopropyl alcohol, saline and distilled water failed to prevent the precipitation of residues on canal walls following the use of NaOCl and CHX. The residues did not interfere with the push-out bond strength of the root filling.

Push-out bond strength of calcium hydroxide and mineral trioxide aggregate based sealers

The adhesiveness of six root canal sealers: Acroseal, Endo CPM, Epiphany, White MTA, Sealapex and Sealer 26 to dentin, was evaluated in a push-out test design. Methods: Twenty eight roots of freshly extracted teeth were gauged with a size 5 Largo drill. With a cutting machine slices of 2 mm were prepared, rinsed with 5.25% NaOCl and a final rinse with 17% EDTA, dried and filled with one of the sealers. After setting their bond strength was measured in a mechanical testing machine. The data were statistically analyzed by using a One Way ANOVA and post hoc Tukey test. Results: The mean and standard deviation from values of bond strength was: Sealapex 2.2±0.4; Endo CPM 3.8±1.3; White MTA 6.0±1.4; Epiphany 10.9±2.6; Sealer 26 12.3±2.3; and Acroseal 12.2±1.4. Acroseal, Sealer 26 and Epiphany presented a significantly (P<0.01) greater bond strength compared with the other sealers. Also White MTA showed higher adhesiveness compared with Endo CPM and Sealapex (P<0.01). Conclusion: The bond strength between endodontic sealers and root dentin was maximal when Acroseal, Sealer 26 and Epiphany were used; Sealapex e Endo CPM, in turn, presented the lowest bond strength mean values.

Evaluation of the pH, calcium release and antibacterial activity of MTA Fillapex

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Radiographic evaluation of root canal cleaning, main and laterals, using different methods of final irrigation

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effectiveness of gutta-percha and Resilon in filling lateral root canals using thermomechanical technique

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of the rotary and/or oscillatory reciprocating systems in the morphological changes of narrow and curved molar root canals anatomy

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)