Silicon quantum dots embedded in a SiO2 matrix: From structural study to carrier transport properties

We study the details of electronic transport related to the atomistic structure of silicon quantum dots embedded in a silicon dioxide matrix using ab initio calculations of the density of states. Several structural and composition features of quantum dots (QDs), such as diameter and amorphization level, are studied and correlated with transport under transfer Hamiltonian formalism. The current is strongly dependent on the QD density of states and on the conduction gap, both dependent on the dot diameter. In particular, as size increases, the available states inside the QD increase, while the QD band gap decreases due to relaxation of quantum confinement. Both effects contribute to increasing the current with the dot size. Besides, valence band offset between the band edges of the QD and the silica, and conduction band offset in a minor grade, increases with the QD diameter up to the theoretical value corresponding to planar heterostructures, thus decreasing the tunneling transmission probability and hence the total current. We discuss the influence of these parameters on electron and hole transport, evidencing a correlation between the electron (hole) barrier value and the electron (hole) current, and obtaining a general enhancement of the electron (hole) transport for larger (smaller) QD. Finally, we show that crystalline and amorphous structures exhibit enhanced probability of hole and electron current, respectively.

Do walking strategies to increase physical activity reduce reported sitting in workplaces: a randomized control trial

Background: Interventions designed to increase workplace physical activity may not automatically reduce high volumes of sitting, a behaviour independently linked to chronic diseases such as obesity and type II diabetes. This study compared the impact two different walking strategies had on step counts and reported sitting times. Methods: Participants were white-collar university employees (n = 179; age 41.3 ± 10.1 years; 141 women), who volunteered and undertook a standardised ten-week intervention at three sites. Preintervention step counts (Yamax SW-200) and self-reported sitting times were measured over five consecutive workdays. Using pre-intervention step counts, employees at each site were randomly allocated to a control group (n = 60; maintain normal behaviour), a route-based walking group (n = 60; at least 10 minutes sustained walking each workday) or an incidental walking group (n = 59; walking in workday tasks). Workday step counts and reported sitting times were re-assessed at the beginning, mid- and endpoint of intervention and group mean± SD steps/day and reported sitting times for pre-intervention and intervention measurement points compared using a mixed factorial ANOVA; paired sample-t-tests were used for follow-up, simple effect analyses. Results: A significant interactive effect (F = 3.5; p < 0.003) was found between group and step counts. Daily steps for controls decreased over the intervention period (-391 steps/day) and increased for route (968 steps/day; t = 3.9, p < 0.000) and incidental (699 steps/day; t = 2.5, p < 0.014) groups. There were no significant changes for reported sitting times, but average values did decrease relative to the control (routes group = 7 minutes/day; incidental group = 15 minutes/day). Reductions were most evident for the incidental group in the first week of intervention, where reported sitting decreased by an average of 21 minutes/day (t = 1.9; p < 0.057). Conclusion: Compared to controls, both route and incidental walking increased physical activity in white-collar employees. Our data suggests that workplace walking, particularly through incidental movement, also has the potential to decrease employee sitting times, but there is a need for on-going research using concurrent and objective measures of sitting, standing and walking.

The International Universities Walking Project: Development of a Framework for Workplace Intervention Using the Delphi Technique

Background: This paper aimed to use the Delphi technique to develop a consensus framework for a multinational, workplace walking intervention. Methods: Ideas were gathered and ranked from eight recognized and emerging experts in the fields of physical activity and health, from universities in Australia, Canada, England, the Netherlands, Northern Ireland, and Spain. Members of the panel were asked to consider the key characteristics of a successful campus walking intervention. Consensus was reached by an inductive, content analytic approach, conducted through an anonymous, three-round, e-mail process. Results: The resulting framework consisted of three interlinking themes defined as “design, implementation, and evaluation.” Top-ranked subitems in these themes included the need to generate research capacity (design), to respond to group needs through different walking approaches (implementation), and to undertake physical activity assessment (evaluation). Themes were set within an underpinning domain, referred to as the “institution” and sites are currently engaging with subitems in this domain, to provide sustainable interventions that reflect the practicalities of local contexts and needs. Conclusions: Findings provide a unique framework for designing, implementing, and evaluating walking projects in universities and highlight the value of adopting the Delphi technique for planning international, multisite health initiatives.

Outcome evaluation of ankle osteoarthritis treatments using spatio-temporal gait parameters and plantar pressure during unconstrained long distance walking : P25

Introduction: Ankle arthrodesis (AD) and total ankle replacement (TAR) are typical treatments for ankle osteoarthritis (AO). Despite clinical interest, there is a lack of their outcome evaluation using objective criteria. Gait analysis and plantar pressure assessment are appropriate to detect pathologies in orthopaedics but they are mostly used in lab with few gait cycles. In this study, we propose an ambulatory device based on inertial and plantar pressure sensors to compare the gait during long-distance trials between healthy subjects (H) and patients with AO or treated by AD and TAR. Methods: Our study included four groups: 11 patients with AO, 9 treated by TAR, 7 treated by AD and 6 control subjects. An ambulatory system (Physilog®, CH) was used for gait analysis; plantar pressure measurements were done using a portable insole (Pedar®-X, DE). The subjects were asked to walk 50 meters in two trials. Mean value and coefficient of variation of spatio-temporal gait parameters were calculated for each trial. Pressure distribution was analyzed in ten subregions of foot. All parameters were compared among the four groups using multi-level model-based statistical analysis. Results: Significant difference (p <0.05) with control was noticed for AO patients in maximum force in medial hindfoot and forefoot and in central forefoot. These differences were no longer significant in TAR and AD groups. Cadence and speed of all pathologic groups showed significant difference with control. Both treatments showed a significant improvement in double support and stance. TAR decreased variability in speed, stride length and knee ROM. Conclusions: In spite of a small sample size, this study showed that ankle function after AO treatments can be evaluated objectively based on plantar pressure and spatio-temporal gait parameters measured during unconstrained walking outside the lab. The combination of these two ambulatory techniques provides a promising way to evaluate foot function in clinics.

Walking Around Barberà

Walking Around Barberà és una aplicació desenvolupada en Android que permet gestionar llocs d'interès del municipi de Barberà del Vallès.

Measurement of the mechanical power of walking by satellite positioning system (GPS).

PURPOSE: This descriptive article illustrates the application of Global Positioning System (GPS) professional receivers in the field of locomotion studies. The technological challenge was to assess the external mechanical work in outdoor walking. METHODS: Five subjects walked five times during 5 min on an athletic track at different imposed stride frequency (from 70-130 steps x min(-1)). A differential GPS system (carrier phase analysis) measured the variation of the position of the trunk at 5 Hz. A portable indirect calorimeter recorded breath-by-breath energy expenditure. RESULTS: For a walking speed of 1.05 +/- 0.11 m x s(-1), the vertical lift of the trunk (43 +/- 14 mm) induced a power of 46.0 +/- 20.4 W. The average speed variation per step (0.15 +/- 0.03 m x s(-1)) produced a kinetic power of 16.9 +/- 7.2 W. As compared with commonly admitted values, the energy exchange (recovery) between the two energy components was low (39.1 +/- 10.0%), which induced an overestimated mechanical power (38.9 +/- 18.3 W or 0.60 W x kg(-1) body mass) and a high net mechanical efficiency (26.9 +/- 5.8%). CONCLUSION: We assumed that the cause of the overestimation was an unwanted oscillation of the GPS antenna. It is concluded that GPS (in phase mode) is now able to record small body movements during human locomotion, and constitutes a promising tool for gait analysis of outdoor unrestrained walking. However, the design of the receiver and the antenna must be adapted to human experiments and a thorough validation study remains to be conducted.

Estudi de l’eficiència aerodinàmica de vehicles pesants de transport de passatgers

Estudi de l’eficiència aerodinàmica de les carrosseries de vehicles pesants de cara a reduir el consum de combustible en autocars de llarg trajecte. L’estudi es basa en tres aspectes: validació del programa de simulació, estudi aerodinàmic de diferents carrosseries d’autocar de mercat i estudi aerodinàmic de diferents complements

Estudi de la influència del vent en l’estabilitat de vehicles pesants de transport de viatgers.

Investigacions recents revelen com l’acció del vent lateral és un efecte molt important en bona part dels accidents ocorreguts en vehicles pesants de transport per carretera. És per això que el perfil aerodinàmic del vehicle esdevé determinant en l’avaluació de les forces laterals que hi actuen.El present projecte té per objecte determinar les forces laterals que s’exerceixen en vehicles pesants de transport de passatgers degut a l’acció del vent i investigar-ne la seva perillositat. Per fer-ho s’utilitzen models numèrics de dinàmica de fluids i, per diferents velocitats del vehicle, es simulen vents amb diferent intensitat i direcció. D’aquí es determinen unes condicions de perillositat en funció, entre d’altres variables, de l’angle d’incidència del vent i de la seva velocitat

G alpha-q/11 protein plays a key role in insulin-induced glucose transport in 3T3-L1 adipocytes.

We evaluated the role of the G alpha-q (Galphaq) subunit of heterotrimeric G proteins in the insulin signaling pathway leading to GLUT4 translocation. We inhibited endogenous Galphaq function by single cell microinjection of anti-Galphaq/11 antibody or RGS2 protein (a GAP protein for Galphaq), followed by immunostaining to assess GLUT4 translocation in 3T3-L1 adipocytes. Galphaq/11 antibody and RGS2 inhibited insulin-induced GLUT4 translocation by 60 or 75%, respectively, indicating that activated Galphaq is important for insulin-induced glucose transport. We then assessed the effect of overexpressing wild-type Galphaq (WT-Galphaq) or a constitutively active Galphaq mutant (Q209L-Galphaq) by using an adenovirus expression vector. In the basal state, Q209L-Galphaq expression stimulated 2-deoxy-D-glucose uptake and GLUT4 translocation to 70% of the maximal insulin effect. This effect of Q209L-Galphaq was inhibited by wortmannin, suggesting that it is phosphatidylinositol 3-kinase (PI3-kinase) dependent. We further show that Q209L-Galphaq stimulates PI3-kinase activity in p110alpha and p110gamma immunoprecipitates by 3- and 8-fold, respectively, whereas insulin stimulates this activity mostly in p110alpha by 10-fold. Nevertheless, only microinjection of anti-p110alpha (and not p110gamma) antibody inhibited both insulin- and Q209L-Galphaq-induced GLUT4 translocation, suggesting that the metabolic effects induced by Q209L-Galphaq are dependent on the p110alpha subunit of PI3-kinase. In summary, (i) Galphaq appears to play a necessary role in insulin-stimulated glucose transport, (ii) Galphaq action in the insulin signaling pathway is upstream of and dependent upon PI3-kinase, and (iii) Galphaq can transmit signals from the insulin receptor to the p110alpha subunit of PI3-kinase, which leads to GLUT4 translocation.

Improvement of walking speed prediction by accelerometry and altimetry, validated by satellite positioning.

Activity monitors based on accelerometry are used to predict the speed and energy cost of walking at 0% slope, but not at other inclinations. Parallel measurements of body accelerations and altitude variation were studied to determine whether walking speed prediction could be improved. Fourteen subjects walked twice along a 1.3 km circuit with substantial slope variations (-17% to +17%). The parameters recorded were body acceleration using a uni-axial accelerometer, altitude variation using differential barometry, and walking speed using satellite positioning (DGPS). Linear regressions were calculated between acceleration and walking speed, and between acceleration/altitude and walking speed. These predictive models, calculated using the data from the first circuit run, were used to predict speed during the second circuit. Finally the predicted velocity was compared with the measured one. The result was that acceleration alone failed to predict speed (mean r = 0.4). Adding altitude variation improved the prediction (mean r = 0.7). With regard to the altitude/acceleration-speed relationship, substantial inter-individual variation was found. It is concluded that accelerometry, combined with altitude measurement, can assess position variations of humans provided inter-individual variation is taken into account. It is also confirmed that DGPS can be used for outdoor walking speed measurements, opening up new perspectives in the field of biomechanics.

Cation Transport Coupled to ATP Hydrolysis By the (Na, K)-ATPase : an integrated, animated model

An Adobe (R) animation is presented for use in undergraduate Biochemistry courses, illustrating the mechanism of Na+ and K+ translocation coupled to ATP hydrolysis by the (Na, K)-ATPase, a P-2c-type ATPase, or ATP-powered ion pump that actively translocates cations across plasma membranes. The enzyme is also known as an E-1/E-2-ATPase as it undergoes conformational changes between the E-1 and E-2 forms during the pumping cycle, altering the affinity and accessibility of the transmembrane ion-binding sites. The animation is based on Horisberger's scheme that incorporates the most recent significant findings to have improved our understanding of the (Na, K)-ATPase structure function relationship. The movements of the various domains within the (Na, K)-ATPase alpha-subunit illustrate the conformational changes that occur during Na+ and K+ translocation across the membrane and emphasize involvement of the actuator, nucleotide, and phosphorylation domains, that is, the "core engine" of the pump, with respect to ATP binding, cation transport, and ADP and P-i release.

Receptor occupancy vs. induction of Na+-K+-ATPase and Na+ transport by aldosterone.

In the urinary bladder of the toad Bufo marinus aldosterone (between 0.8 and 100 nM) stimulates Na+ transport [half-maximal induction concentration (K1/2) = 6.5 nM]. At low hormone concentrations (0.8-8 nM), the increase of Na+ transport between 0.75 and 2.5 h is accompanied by a fall in transepithelial resistance (R). Higher hormone concentrations (30-800 nM) induce an additional resistance-independent fraction of Na+ transport within 2.5-8 h. From 6 h on, aldosterone (between 0.2 and 20 nM) stimulates in the same tissue the biosynthesis rate of the alpha- and beta-subunits of Na+-K+-ATPase (K1/2 = 3 and 1.5 nM, respectively). New pump synthesis is thus not a prerequisite for the early mineralocorticoid response but might be linked to the late transport event. The mineralocorticoid response is usually ascribed to interaction with the higher affinity type 1 receptor. In the present study we show, however, that at least 55% of the overall Na+ transport response is linked to nuclear occupation of the lower affinity type 2 receptors [dissociation constant (Kd) = 50 nM, maximum number of binding sites (Nmax) = 315 fmol/mg protein]. Distinct aldosterone effects, such as the fall in R and the increase in Na+-K+-ATPase synthesis, are more closely related to occupation of type 1 receptors (Kd = 0.3 nM, Nmax = 23 fmol/mg protein). At maximal induction of these latter parameters, only about 20% of type 2 receptors are occupied. These results suggest that both types of aldosterone receptors are involved in the mediation of the full mineralocorticoid response: type 1 in the early and late and type 2 particularly in the late tissue response.

Harvesting and transport of root biomass from fast-growing poplar plantations

Abstract