Proof of concept of an imaging system demonstrator for PET applications with SiPM

A PET imaging system demonstrator based on LYSO crystal arrays coupled to SiPM matrices is under construction at the University and INFN of Pisa. Two SiPM matrices, composed of 8×8 SiPM pixels, and 1,5 mm pitch, have been coupled one to one to a LYSO crystals array and read out by a custom electronics system. front-end ASICs were used to read 8 channels of each matrix. Data from each front-end were multiplexed and sent to a DAQ board for the digital conversion; a motherboard collects the data and communicates with a host computer through a USB port for the storage and off-line data processing. In this paper we show the first preliminary tomographic image of a point-like radioactive source acquired with part of the two detection heads in time coincidence.

Opportunities and challenges in the use of inorganic fullerene-like nanoparticles to produce advanced polymer nanocomposites

Polymer/inorganic nanoparticle nanocomposites have garnered considerable academic and industrial interest over recent decades in the development of advanced materials for a wide range of applications. In this respect, the dispersion of so-called inorganic fullerene-like (IF) nanoparticles, e.g., tungsten disulfide (IF-WS2) or molybdenum disulfide (IF-MoS2), into polymeric matrices is emerging as a new strategy. The surprising properties of these layered metal dichalcogenides such as high impact resistance and superior tribological behavior, attributed to their nanoscale size and hollow quasi-spherical shape, open up a wide variety of opportunities for applications of these inorganic compounds. The present work presents a detailed overview on research in the area of IF-based polymer nanocomposites, with special emphasis on the use of IF-WS2 nanoparticles as environmentally friendly reinforcing fillers. The incorporation of IF particles has been shown to be efficient for improving thermal, mechanical and tribological properties of various thermoplastic polymers, such as polypropylene, nylon-6, poly(phenylene sulfide), poly(ether ether ketone), where nanocomposites were fabricated by simple melt-processing routes without the need for modifiers or surfactants. This new family of nanocomposites exhibits similar or enhanced performance when compared with nanocomposites that incorporate carbon nanotubes, carbon nanofibers or nanoclays, but are substantially more cost-effective, efficient and environmentally satisfactory. Most recently, innovative approaches have been described that exploit synergistic effects to produce new materials with enhanced properties, including the combined use of micro- and nanoparticles such as IF-WS2/nucleating agent or IF-WS2/carbon fiber, as well as dual nanoparticle systems such as SWCNT/IF-WS2 where each nanoparticle has different characteristics. The structure–property relationships of these nanocomposites are discussed and potential applications proposed ranging from medicine to the aerospace, automotive and electronics industries.

AquaData and AquaGIS: Two computer utilities for temporal and spatial simulations of water-limited yield with AquaCrop.

The crop simulation model AquaCrop, recently developed by FAO can be used for a wide range of purposes. However, in its present form, its use over large areas or for applications that require a large number of simulations runs (e.g., long-term analysis), is not practical without developing software to facilitate such applications. Two tools for managing the inputs and outputs of AquaCrop, named AquaData and AquaGIS, have been developed for this purpose and are presented here. Both software utilities have been programmed in Delphi v. 5 and in addition, AquaGIS requires the Geographic Information System (GIS) programming tool MapObjects. These utilities allow the efficient management of input and output files, along with a GIS module to develop spatial analysis and effect spatial visualization of the results, facilitating knowledge dissemination. A sample of application of the utilities is given here, as an AquaCrop simulation analysis of impact of climate change on wheat yield in Southern Spain, which requires extensive input data preparation and output processing. The use of AquaCrop without the two utilities would have required approximately 1000 h of work, while the utilization of AquaData and AquaGIS reduced that time by more than 99%. Furthermore, the use of GIS, made it possible to perform a spatial analysis of the results, thus providing a new option to extend the use of the AquaCrop model to scales requiring spatial and temporal analyses.

High thermal neutron flux effects on structural and macroscopic properties of alkali-borosilicate glasses used as neutron guide substrate

The behaviour of four alkali-borosilicate glasses under homogeneous thermal neutron irradiation has been studied. These materials are used for the manufacturing of neutron guides which are installed in most facilities as devices to transport neutrons from intense sources such as nuclear reactors or spallation sources up to scientific instruments. Several experimental techniques such as Raman, NMR, SANS and STEM have been employed in order to understand the rather different macroscopic behaviour under irradiation of materials that belong to a same glass family. The results have shown that the remarkable glass shrinking observed for neutron doses below 0.5 · 10 18 n/cm 2 critically depends upon the presence of domains where silicate and borate network do not mix.

Telemetría de vehículos FSAE con microcontrolador PIC32 y transceptor de radio CC1101

Quizás el campo de las telecomunicaciones sea uno de los campos en el que más se ha progresado en este último siglo y medio, con la ayuda de otros campos de la ciencia y la técnica tales como la computación, la física electrónica, y un gran número de disciplinas, que se han utilizado estos últimos 150 años en conjunción para mejorarse unas con la ayuda de otras. Por ejemplo, la química ayuda a comprender y mejorar campos como la medicina, que también a su vez se ve mejorada por los progresos en la electrónica creados por los físicos y químicos, que poseen herramientas más potentes para calcular y simular debido a los progresos computacionales. Otro de los campos que ha sufrido un gran avance en este último siglo es el de la automoción, aunque estancados en el motor de combustión, los vehículos han sufrido enormes cambios debido a la irrupción de los avances en la electrónica del automóvil con multitud de sistemas ya ampliamente integrados en los vehículos actuales. La Formula SAE® o Formula Student es una competición de diseño, organizada por la SAE International (Society of Automotive Engineers) para estudiantes de universidades de todo el mundo que promueve la ingeniería a través de una competición donde los miembros del equipo diseñan, construyen, desarrollan y compiten en un pequeño y potente monoplaza. En el ámbito educativo, evitando el sistema tradicional de clases magistrales, se introducen cambios en las metodologías de enseñanza y surge el proyecto de la Fórmula Student para lograr una mejora en las acciones formativas, que permitan ir incorporando nuevos objetivos y diseñar nuevas situaciones de aprendizaje que supongan una oportunidad para el desarrollo de competencias de los alumnos, mejorar su formación como ingenieros y contrastar sus progresos compitiendo con las mejores universidades del mundo. En este proyecto se pretende dotar a los alumnos de las escuelas de ingeniería de la UPM que desarrollan el vehículo de FSAE de una herramienta de telemetría con la que evaluar y probar comportamiento del vehículo de FSAE junto con sus subsistemas que ellos mismos diseñan, con el objetivo de evaluar el comportamiento, introducir mejoras, analizar resultados de una manera más rápida y cómoda, con el objetivo de poder progresar más rápidamente en su desarrollo, recibiendo y almacenando una realimentación directa e instantánea del funcionamiento mediante la lectura de los datos que circulan por el bus CAN del vehículo. También ofrece la posibilidad de inyectar datos a los sistemas conectados al bus CAN de manera remota. Se engloba en el conjunto de proyectos de la FSAE, más concretamente en los basados en la plataforma PIC32 y propone una solución conjunta con otros proyectos o también por sí sola. Para la ejecución del proyecto se fabricó una placa compuesta de dos placas de circuito impreso, la de la estación base que envía comandos, instrucciones y datos para inyectar en el bus CAN del vehículo mediante radiofrecuencia y la placa que incorpora el vehículo que envía las tramas que circulan por el bus CAN del vehículo con los identificadores deseados, ejecuta los comandos recibidos por radiofrecuencia y salva las tramas CAN en una memoria USB o SD Card. Las dos PCBs constituyen el hardware del proyecto. El software se compone de dos programas. Un programa para la PCB del vehículo que emite los datos a la estación base, codificado en lenguaje C con ayuda del entorno de desarrollo MPLAB de Microchip. El otro programa hecho con LabView para la PCB de la estación base que recibe los datos provenientes del vehículo y los interpreta. Se propone un hardware y una capa o funciones de software para los microcontroladores PIC32 (similar al de otros proyectos del FSAE) para la transmisión de las tramas del bus CAN del vehículo de manera inalámbrica a una estación base, capaz de insertar tramas en el bus CAN del vehículo enviadas desde la estación base. También almacena estas tramas CAN en un dispositivo USB o SD Card situado en el vehículo. Para la transmisión de los datos se hizo un estudio de las frecuencias de transmisión, la legislación aplicable y los tipos de transceptores. Se optó por utilizar la banda de radiofrecuencia de uso común ISM de 433MHz mediante el transceptor integrado CC110L de Texas Instruments altamente configurable y con interfaz SPI. Se adquirieron dos parejas de módulos compatibles, con amplificador de potencia o sin él. LabView controla la estación que recoge las tramas CAN vía RF y está dotada del mismo transceptor de radio junto con un puente de comunicaciones SPI-USB, al que se puede acceder de dos diferentes maneras, mediante librerías dll, o mediante NI-VISA con transferencias RAW-USB. La aplicación desarrollada posee una interfaz configurable por el usuario para la muestra de los futuros sensores o actuadores que se incorporen en el vehículo y es capaz de interpretar las tramas CAN, mostrarlas, gráfica, numéricamente y almacenar esta información, como si fuera el cuadro de instrumentos del vehículo. Existe una limitación de la velocidad global del sistema en forma de cuello de botella que se crea debido a las limitaciones del transceptor CC110L por lo que si no se desea filtrar los datos que se crean necesarios, sería necesario aumentar el número de canales de radio para altas ocupaciones del bus CAN. Debido a la pérdida de relaciones con el INSIA, no se pudo probar de manera real en el propio vehículo, pero se hicieron pruebas satisfactorias (hasta 1,6 km) con una configuración de tramas CAN estándar a una velocidad de transmisión de 1 Mbit/s y un tiempo de bit de 1 microsegundo. El periférico CAN del PIC32 se programará para cumplir con estas especificaciones de la ECU del vehículo, que se presupone que es la MS3 Sport de Bosch, de la que LabView interpretará las tramas CAN recibidas de manera inalámbrica. Para poder probar el sistema, ha sido necesario reutilizar el hardware y adaptar el software del primer prototipo creado, que emite tramas CAN preprogramadas con una latencia también programable y que simulará al bus CAN proporcionando los datos a transmitir por el sistema que incorpora el vehículo. Durante el desarrollo de este proyecto, en las etapas finales, el fabricante del puente de comunicaciones SPI-USB MCP2210 liberó una librería (dll) compatible y sin errores, por lo que se nos ofrecía una oportunidad interesante para la comparación de las velocidades de acceso al transceptor de radio, que se presuponía y se comprobó más eficiente que la solución ya hecha mediante NI-VISA. ABSTRACT. The Formula SAE competition is an international university applied to technological innovation in vehicles racing type formula, in which each team, made up of students, should design, construct and test a prototype each year within certain rules. The challenge of FSAE is that it is an educational project farther away than a master class. The goal of the present project is to make a tool for other students to use it in his projects related to FSAE to test and improve the vehicle, and, the improvements that can be provided by the electronics could be materialized in a victory and win the competition with this competitive advantage. A telemetry system was developed. It sends the data provided by the car’s CAN bus through a radio frequency transceiver and receive commands to execute on the system, it provides by a base station on the ground. Moreover, constant verification in real time of the status of the car or data parameters like the revolutions per minute, pressure from collectors, water temperature, and so on, can be accessed from the base station on the ground, so that, it could be possible to study the behaviour of the vehicle in early phases of the car development. A printed circuit board, composed of two boards, and two software programs in two different languages, have been developed, and built for the project implementation. The software utilized to design the PCB is Orcad10.5/Layout. The base station PCB on a PC receives data from the PCB connected to the vehicle’s CAN bus and sends commands like set CAN filters or masks, activate data logger or inject CAN frames. This PCB is connected to a PC via USB and contains a bridge USB-SPI to communicate with a similar transceiver on the vehicle PCB. LabView controls this part of the system. A special virtual Instrument (VI) had been created in order to add future new elements to the vehicle, is a dashboard, which reads the data passed from the main VI and represents them graphically to studying the behaviour of the car on track. In this special VI other alums can make modifications to accommodate the data provided from the vehicle CAN’s bus to new elements on the vehicle, show or save the CAN frames in the form or format they want. Two methods to access to SPI bus of CC110l RF transceiver over LabView have been developed with minimum changes between them. Access through NI-VISA (Virtual Instrument Software Architecture) which is a standard for configuring, programming, USB interfaces or other devices in National Instruments LabView. And access through DLL (dynamic link library) supplied by the manufacturer of the bridge USB-SPI, Microchip. Then the work is done in two forms, but the dll solution developed shows better behaviour, and increase the speed of the system because has less overload of the USB bus due to a better efficiency of the dll solution versus VISA solution. The PCB connected to the vehicle’s CAN bus receives commands from the base station PCB on a PC, and, acts in function of the command or execute actions like to inject packets into CAN bus or activate data logger. Also sends over RF the CAN frames present on the bus, which can be filtered, to avoid unnecessary radio emissions or overflowing the RF transceiver. This PCB consists of two basic pieces: A microcontroller with 32 bit architecture PIC32MX795F512L from Microchip and the radio transceiver integrated circuit CC110l from Texas Instruments. The PIC32MX795F512L has an integrated CAN and several peripherals like SPI controllers that are utilized to communicate with RF transceiver and SD Card. The USB controller on the PIC32 is utilized to store CAN data on a USB memory, and change notification peripheral is utilized like an external interrupt. Hardware for other peripherals is accessible. The software part of this PCB is coded in C with MPLAB from Microchip, and programming over PICkit 3 Programmer, also from Microchip. Some of his libraries have been modified to work properly with this project and other was created specifically for this project. In the phase for RF selection and design is made a study to clarify the general aspects of regulations for the this project in order to understand it and select the proper band, frequency, and radio transceiver for the activities developed in the project. From the different options available it selects a common use band ICM, with less regulation and free to emit with restrictions and disadvantages like high occupation. The transceiver utilized to transmit and receive the data CC110l is an integrated circuit which needs fewer components from Texas Instruments and it can be accessed through SPI bus. Basically is a state machine which changes his state whit commands received over an SPI bus or internal events. The transceiver has several programmable general purpose Inputs and outputs. These GPIOs are connected to PIC32 change notification input to generate an interrupt or connected to GPIO to MCP2210 USB-SPI bridge to inform to the base station for a packet received. A two pair of modules of CC110l radio module kit from different output power has been purchased which includes an antenna. This is to keep away from fabrication mistakes in RF hardware part or designs, although reference design and gerbers files are available on the webpage of the chip manufacturer. A neck bottle is present on the complete system, because the maximum data rate of CC110l transceiver is a half than CAN bus data rate, hence for high occupation of CAN bus is recommendable to filter the data or add more radio channels, because the buffers can’t sustain this load along the time. Unfortunately, during the development of the project, the relations with the INSIA, who develops the vehicle, was lost, for this reason, will be made impossible to test the final phases of the project like integration on the car, final test of integration, place of the antenna, enclosure of the electronics, connectors selection, etc. To test or evaluate the system, it was necessary to simulate the CAN bus with a hardware to feed the system with entry data. An early hardware prototype was adapted his software to send programed CAN frames at a fixed data rate and certain timing who simulate several levels of occupation of the CAN Bus. This CAN frames emulates the Bosch ECU MS3 Sport.

Face, content, and construct validity of the EndoViS training system for objective assessment of psychomotor skills of laparoscopic surgeons

Background The aim of this study is to present face, content, and constructs validity of the endoscopic orthogonal video system (EndoViS) training system and determines its efficiency as a training and objective assessment tool of the surgeons’ psychomotor skills. Methods Thirty-five surgeons and medical students participated in this study: 11 medical students, 19 residents, and 5 experts. All participants performed four basic skill tasks using conventional laparoscopic instruments and EndoViS training system. Subsequently, participants filled out a questionnaire regarding the design, realism, overall functionality, and its capabilities to train hand–eye coordination and depth perception, rated on a 5-point Likert scale. Motion data of the instruments were obtained by means of two webcams built into a laparoscopic physical trainer. To identify the surgical instruments in the images, colored markers were placed in each instrument. Thirteen motion-related metrics were used to assess laparoscopic performance of the participants. Statistical analysis of performance was made between novice, intermediate, and expert groups. Internal consistency of all metrics was analyzed with Cronbach’s α test. Results Overall scores about features of the EndoViS system were positives. Participants agreed with the usefulness of tasks and the training capacities of EndoViS system (score >4). Results presented significant differences in the execution of three skill tasks performed by participants. Seven metrics showed construct validity for assessment of performance with high consistency levels. Conclusions EndoViS training system has been successfully validated. Results showed that EndoViS was able to differentiate between participants of varying laparoscopic experience. This simulator is a useful and effective tool to objectively assess laparoscopic psychomotor skills of the surgeons.

Rock friction and its implications for earthquake prediction examined via models of Parkfield earthquakes.

The friction of rocks in the laboratory is a function of time, velocity of sliding, and displacement. Although the processes responsible for these dependencies are unknown, constitutive equations have been developed that do a reasonable job of describing the laboratory behavior. These constitutive laws have been used to create a model of earthquakes at Parkfield, CA, by using boundary conditions appropriate for the section of the fault that slips in magnitude 6 earthquakes every 20-30 years. The behavior of this model prior to the earthquakes is investigated to determine whether or not the model earthquakes could be predicted in the real world by using realistic instruments and instrument locations. Premonitory slip does occur in the model, but it is relatively restricted in time and space and detecting it from the surface may be difficult. The magnitude of the strain rate at the earth's surface due to this accelerating slip seems lower than the detectability limit of instruments in the presence of earth noise. Although not specifically modeled, microseismicity related to the accelerating creep and to creep events in the model should be detectable. In fact the logarithm of the moment rate on the hypocentral cell of the fault due to slip increases linearly with minus the logarithm of the time to the earthquake. This could conceivably be used to determine when the earthquake was going to occur. An unresolved question is whether this pattern of accelerating slip could be recognized from the microseismicity, given the discrete nature of seismic events. Nevertheless, the model results suggest that the most likely solution to earthquake prediction is to look for a pattern of acceleration in microseismicity and thereby identify the microearthquakes as foreshocks.

A historical account of types of fuzzy sets and their relationships

In this paper, we review the definition and basic properties of the different types of fuzzy sets that have appeared up to now in the literature. We also analyze the relationships between them and enumerate some of the applications in which they have been used.

Análise de incerteza de um sistema automatizado para ensaios de aspersores de irrigação

Ensaios de distribuição de água de aspersores são convencionalmente realizados manualmente, requerendo tempo e mão de obra treinada. A automação desses ensaios proporciona redução da demanda por esses recursos e apresenta potencial para minimizar falhas e/ou desvios de procedimento. Atualmente, laboratórios de ensaio e calibração acreditados junto a organismos legais devem apresentar em seus relatórios a incerteza de medição de seus instrumentos e sistemas de medição. Além disso, normas de ensaio e calibração apresentam especificação de incerteza aceitável, como a norma de ensaios de distribuição de água por aspersores, ISO 15886-3 (2012), a qual exige uma incerteza expandida de até 3% em 80% dos coletores. Os objetivos deste trabalho foram desenvolver um sistema automatizado para os ensaios de aspersores em laboratório e realizar a análise de incerteza de medição, para sua quantificação nos resultados de ensaio e para dar suporte ao dimensionamento dos tubos de coleta. O sistema automático foi constituído por um subsistema de gerenciamento, por meio de um aplicativo supervisório, um de pressurização e um de coleta, por meio de módulos eletrônicos microprocessados desenvolvidos. De acordo com instruções do sistema de gerenciamento o sistema de pressurização ajustava a pressão no aspersor por meio do controle da rotação da motobomba, e o sistema de coleta realizava a medição da intensidade de precipitação de água ao longo do raio de alcance do aspersor. A água captada por cada coletor drenava para um tubo de coleta, que estava conectado a uma das válvulas solenoides de um conjunto, onde havia um transmissor de pressão. Cada válvula era acionada individualmente numa sequência para a medição do nível de água em cada tubo de coleta, por meio do transmissor. Por meio das análises realizadas, as menores incertezas foram obtidas para os menores diâmetros de tubo de coleta, sendo que se deve utilizar o menor diâmetro possível. Quanto ao tempo de coleta, houve redução da incerteza de medição ao se aumentar a duração, devendo haver um tempo mínimo para se atingir a incerteza-alvo. Apesar de cada intensidade requer um tempo mínimo para garantir a incerteza, a diferença mínima de nível a ser medida foi a mesma. Portanto, para os ensaios visando atender a incerteza, realizou-se o monitoramento da diferença de nível nos tubos, ou diferença de nível, facilitando a realização do ensaio. Outra condição de ensaio considerou um tempo de coleta para 30 voltas do aspersor, também exigido pela norma ISO 15886-3 (2012). A terceira condição considerou 1 h de coleta, como tradicionalmente realizado. As curvas de distribuição de água obtidas por meio do sistema desenvolvido foram semelhantes às obtidas em ensaios convencionais, para as três situações avaliadas. Para tempos de coleta de 1 h ou 30 voltas do aspersor o sistema automático requereu menos tempo total de ensaio que o ensaio convencional. Entretanto, o sistema desenvolvido demandou mais tempo para atingir a incerteza-alvo, o que é uma limitação, mesmo sendo automatizado. De qualquer forma, o sistema necessitava apenas que um técnico informasse os parâmetros de ensaio e o acionasse, possibilitando que o mesmo alocasse seu tempo em outras atividades.

The Impact of Visa Liberalisation in Eastern Partnership Countries, Russia and Turkey on Trans-Border Mobility. CEPS Liberty and Security in Europe No. 63, March 2014

Schengen Visa liberalisation in the Eastern Partnership countries, Russia and Turkey has proven to have a huge transformative potential across the justice, liberty and security policies of the countries where it has been deployed. Far-reaching technical reforms in the fields of document security, irregular migration and border management, public order security and fundamental rights have to be implemented so that visa-free travel can be allowed. Evidence provided by visa applications data reveals that visa liberalisation is a logical step, provided that the technical reforms are adopted and implemented. This study analyses the current state of play of the implementation of the EU visa policy instruments and assesses the positive impact of visa-free travel on trans-border mobility according to current visa application statistics.

Informational Barriers to Energy Efficiency - Theory and European Policies. Bruges European Economic Research (BEER) Papers 15/2009

This BEER addresses informational barriers to energy efficiency. It is a widely acknowledged result that an energy efficiency gap exists implying that the level of energy efficiency is at an inefficiently low level. Several barriers to energy efficiency create this gap and the presence of asymmetric information is likely to be one such barrier. In this article a theoretical framework is presented addressing the issues of moral hazard and adverse selection related to energy efficiency. Based on the theoretical framework, European policies on energy efficiency are evaluated. The article is divided into two main parts. The first part presents the theory on information asymmetries and its consequences on energy efficiency focusing on the problems of moral hazard and adverse selection. Having established a theoretical framework to understand the agency barriers to energy efficiency, the second part evaluates the policies of the European Union on energy efficiency. The BEER finds that problems of moral hazard and adverse selection indeed can help explain the seemingly low levels of energy. In both presented models the cost to the principal from implementing high energy efficiency outcome is increased with the informational asymmetries. The theory reveals two implications to policies on energy efficiency. First, the development of measures to enable contractual parties to base remuneration on energy performance must be enhanced, and second, the information on technologies and the education of consumers and installers on energy efficiency must be increased. This could be complemented with certification of installers and energy efficiency advisors to enable consumers to select good agents. Finally, it is found that the preferred EU policy instrument on energy efficiency, so far, seems to be the use of minimum requirements. Less used in EU legislation is the use of measuring and verification as well as the use of certifications. Therefore, it is concluded that the EU should consider an increased use of these instruments, and in particular focus on a further development of standards on measurability and verification as well as an increased focus on education of consumers as well as installers and advisors on energy efficiency.

Energy Efficiency: Trends and Perspectives in the Southern Mediterranean. MEDPRO Technical Report No. 21/December 2012

This paper has two objectives. First, it attempts to establish the potential of policies on energy efficiency and energy demand-side management in the southern Mediterranean region. Second, by examining past trends in energy intensity and trends up to 2030, it analyses the prospects and costs of such policies, compared with expected developments in the price of energy resources. Based on both analyses (MEDPRO WP4) and on prospects for growth (MEDPRO WP8), it seems that energy intensity in the Mediterranean should fall perceptibly by approximately 13% in the next 20 years. But given the programmed energy mix, this will not limit emissions of CO2, which are likely to increase by more than 90%. The paper first presents the rationale for demand-side management (DSM) policies. After a general discussion of concepts, it tackles the question of instruments and measures for implementing such policies, before posing the question of the cost-efficiency approach for monitoring the measures the authorities introduce. Secondly, the paper assesses energy consumption and energy efficiency in the countries of the southern Mediterranean and the ways in which their main economic sectors have changed in recent decades. The third section outlines the demand management measures introduced and, taking Tunisia and Egypt as examples, estimates the cost of such policies. The fourth and last section offers a forecast analysis of energy consumption in the Mediterranean up to 2030, highlighting probable trends in terms of final consumption, energy intensity, energy mix and emissions of CO2. The section concludes with estimates in terms of cost, comparing objectives for lower intensity, results in terms of resource savings and the types of costs this approach represents.

Linking Policy and Practice:The Case of EU-UNICEF Cooperation on the Rights of the Child in Third Countries. IES WORKING PAPER 4/2013

This Working Paper offers detailed analysis of EU-UNICEF cooperation on the rights of the child in the European Union's external relations, in particular as regards linkages between the EU policy priorities and concrete actions to advance the protection and promotion of child rights in third countries. It addresses a number of crucial questions: how has the EU’s external policy on the rights of the child developed over the past decade, what were these developments influenced by and what role did UNICEF play in these processes; what is the legal and policy framework for EU-UNICEF cooperation in foreign policy and what added-value it brings; what mechanisms are used by the EU and UNICEF to improve child rights protection in third countries and what are the motivations behind their field cooperation. The study starts by examining the development of the EU’s foreign policy on the rights of the child and covers the legal basis enshrined in EU treaties, the policy framework, and the implementation instruments and then investigates the evolution of the EU’s relations with the United Nations. The paper focuses on the EU’s cooperation with UNICEF by looking into the legal and political framework for EU-UNICEF relations, the policy-oriented cooperation and joint implementation of projects on the ground in third countries. This section outlines the rationale behind the practical cooperation as well as the factors for success and obstacles hindering the delivery of sustainable results. Finally, the Working Paper concludes with suggestions on how EU-UNICEF cooperation could be further enhanced following recent developments, namely the 2012 EU Strategic Framework and the Action Plan on Human Rights as well as human rights country strategies.

The EU’s Response to the Refugee Crisis: Taking Stock and Setting Policy Priorities. CEPS Essay No. 20, 16 December 2015

What have been the most important EU policy and legal responses to the 2015 refugee crisis? Is Europe taking effectively responsibility in compliance with its founding principles? This Essay takes stock of the main results and policy outputs from the EU’s interventions in the refugee crisis. It critically highlights the outstanding policy dilemmas confronting the adopted instruments and puts forwards a set of policy priorities to guide the next phases of the European Agenda on Migration.

Setting the Scene: Assessing Opportunities and Threats of the European Neighbourhood

Opinions diverge to what extent the European Neighbourhood Policy has made progress towards achieving its aims, which are – as stated in the Lisbon treaty – to “establish an area of prosperity and good neighbourhoudliness, founded on EU-values”. Today it is necessary to re-think the ENP: What can the ENP achieve with its instruments and what shall it achieve? In which fields do the neighbours have specific expectations towards the ENP? And how are these expectations paralleled by what the European Union is disposed to offer?