Determination of paracetamol at a graphite-polyurethane composite electrode as an amperometric flow detector

A bare graphite-polyurethane composite was evaluated as an amperometric flow injection detector in the determination of paracetamol (APAP) in pharmaceutical formulations. A linear analytical curve was observed in the 5.00 x 10-5 to 5.00 x 10-3 mol L-1 range with a minimum detectable net concentration of 18.9 µmol L-1 and 180 determinations h-1, after optimization of parameters such as the detection potential, sample loop volume, and carrier solution flow rate. Interference of ascorbic acid was observed, however, it was possible overcome the interference, reaching results that agreed with HPLC within 95% confidence level. These results showed that the graphite-polyurethane composite can be used as an amperometric detector for flow analysis in the determination of APAP.

Development and validation of a simple and rapid capillary zone electrophoresis method for determination of nnrti nevirapine in pharmaceutical formulations

A simple and fast capillary zone electrophoresis (CZE) method has been developed and validated for quantification of a non-nucleoside reverse transcriptase inhibitor (NNRTI) nevirapine, in pharmaceuticals. The analysis was optimized using 10 mmol L-1 sodium phosphate buffer pH 2.5, +25 kV applied voltage, hydrodynamic injection 0.5 psi for 5 s and direct UV detection at 200 µm. Diazepam (50.0 µg mL-1) was used as internal standard. Under these conditions, nevirapine was analyzed in approximately less than 2.5 min. The analytical curve presented a coefficient of correlation of 0.9994. Limits of detection and quantification were 1.4 µg mL-1 and 4.3 µg mL-1, respectively. Intra- and inter-day precision expressed as relative standard deviations were 1.4% and 1.3%, respectively and the mean recovery was 100.81%. The active pharmaceutical ingredient was subjected to hydrolysis (acid, basic and neutral) and oxidative stress conditions. No interference of degradation products and tablet excipients were observed. This method showed to be rapid, simple, precise, accurate and economical for determination of nevirapine in pharmaceuticals and it is suitable for routine quality control analysis since CE offers benefits in terms of quicker method development and significantly reduced operating costs.

A biosensor based on immobilization of lactate oxidase in a PB-CTAB film for FIA determination of lactate in beer samples

An amperometric lactate biosensor with lactate oxidase immobilized into a Prussian Blue (PB) modified electrode was fabricated. The advantage of using cetyltrimethylammonium bromide (CTAB) in the electrodeposition step of PB films onto glassy carbon surfaces was confirmed taking into account both the stability and sensitivity of the measurements. The biosensor was used in the development of a FIA amperometric method for the determination of lactate. Under optimal operating conditions (pH = 6.9, E = -0.1 V), the linear response of the method was extended up to 0.28 µmol L-1 lactate with a limit of detection of 0.84 mmol L-1. The repeatability of the method for injections of a 0.28 mmol L-1 lactate solution was 2.2 % (n = 18). The usefulness of the method was demonstrated by determining lactate in beer samples and the results were in good agreement with those obtained by using a reference spectrophotometric enzyme method.

Solid-phase microextraction for determination of 3-chloro-4-(dichloromethyl)-5-hydroxy-2[5H]-furanone in water

Solid-phase microextraction, using on-line bis(trimethylsilyl)trifluoroacetamide derivatisation, gas chromatography, and mass spectrometry, was evaluated in the quantification of 3-chloro-4-(dichloromethyl)-5-hydroxy-2(5H)-furanone (MX) in water samples. Fibres encompassing a wide range of polarities were used with headspace and direct immersion sampling. For the immersion procedure, various parameters affecting MX extraction, including pH, salinity, temperature, and extraction time were evaluated. The optimised method (polyacrylate fibre; 20% Na2SO4; pH 2.0; 60 min; 20 °C) was applied for reservoir chlorinated water samples-either natural or spiked with MX (50 ng L-1 and 100 ng L-1). The recovery of MX ranged from 44 to 72%. Quantification of MX in water samples was done using external standard and the selected ion monitoring mode. Correlation coefficient (0.98%), relative standard deviation (5%), limit of detection (30 ng L-1) and limit of quantification (50 ng L-1) were obtained from calibration curve.

(Im)possibilidades de implementar uma direção única no SUS em município de grande porte: o caso de São Paulo, Brasil

A construção da direção única na saúde constitui-se um desafio para a gestão local do SUS, particularmente para municípios de grande porte. Este artigo analisou o processo de implementação do SUS no município de São Paulo, visando identificar estratégias para viabilizar uma direção única, no período de 2001 a 2008. Com base em um estudo de caso, foram utilizados dados obtidos de informantes privilegiados da gestão e de documentos de gestão. O conceito de integração sanitária foi utilizado como categoria analítica. Foram analisados movimentos e estratégias dos atores institucionais envolvidos diretamente na gestão do SUS, os gestores municipal e estadual. Observaram-se avanços institucionais como a municipalização das unidades básicas de saúde estaduais e a habilitação do município na gestão plena do sistema municipal. Apesar dessa condição de gestão e da identidade político-partidária entre os governos municipal e estadual desde 2005, constatou-se a coexistência de dois subsistemas públicos de saúde pouco integrados. Um municipal, que concentrava os serviços de atenção básica; outro estadual, que concentrava parte considerável dos serviços de média e alta complexidades. Instrumentos de gestão adotados, como o sistema de regulação, mostraram-se frágeis para superar a falta de integração entre os referidos subsistemas. Como implementar a direção única no SUS implica uma (re)divisão de recursos e poder, discute-se que não bastam normas nem instrumentos de gestão para viabilizá-la. É um desafio estratégico para o SUS implementar processo de negociação, envolvendo os atores institucionais e políticos, visando a pactuação de um projeto político na saúde.

Rapid detection of bovine coronavirus by a semi-nested RT-PCR

Bovine coronavirus (BCoV) is a member of the group 2 of the Coronavirus (Nidovirales: Coronaviridae) and the causative agent of enteritis in both calves and adult bovine, as well as respiratory disease in calves. The present study aimed to develop a semi-nested RT-PCR for the detection of BCoV based on representative up-to-date sequences of the nucleocapsid gene, a conserved region of coronavirus genome. Three primers were designed, the first round with a 463bp and the second (semi-nested) with a 306bp predicted fragment. The analytical sensitivity was determined by 10-fold serial dilutions of the BCoV Kakegawa strain (HA titre: 256) in DEPC treated ultra-pure water, in fetal bovine serum (FBS) and in a BCoV-free fecal suspension, when positive results were found up to the 10-2, 10-3 and 10-7 dilutions, respectively, which suggests that the total amount of RNA in the sample influence the precipitation of pellets by the method of extraction used. When fecal samples was used, a large quantity of total RNA serves as carrier of BCoV RNA, demonstrating a high analytical sensitivity and lack of possible substances inhibiting the PCR. The final semi-nested RT-PCR protocol was applied to 25 fecal samples from adult cows, previously tested by a nested RT-PCR RdRp used as a reference test, resulting in 20 and 17 positives for the first and second tests, respectively, and a substantial agreement was found by kappa statistics (0.694). The high sensitivity and specificity of the new proposed method and the fact that primers were designed based on current BCoV sequences give basis to a more accurate diagnosis of BCoV-caused diseases, as well as to further insights on protocols for the detection of other Coronavirus representatives of both Animal and Public Health importance.

Risco de eventos adversos e uso de medicamentos potencialmente interativos

Este estudo é parte do Estudo SABE e teve por objetivo verificar a freqüência de uso de medicamentos impróprios e potencialmente interativos (PI) pela população idosa residente na zona urbana do município de São Paulo. Os medicamentos foram classificados segundo o sistema ATC com características e potencial de interação. Utilizou-se estatística descritiva. Foram identificados 47,1 por cento de medicamentos (PI) e 10,6 por cento de uso impróprio. Os inibidores enzimáticos (41 por cento) foram os mais freqüentes, sendo o diclofenaco (3 por cento) o impróprio e PI mais usado. Os riscos identificados devem alertar os profissionais para a importância de analisar criteriosamente os medicamentos prescritos ao idoso

Cobertura de linhas telefônicas residenciais e vícios potenciais em estudos epidemiológicos

OBJETIVO: Estimar o efeito da taxa de cobertura de linhas telefônicas residenciais em potenciais vícios de informação em inquéritos epidemiológicos. MÉTODOS: Foram utilizadas as bases de dados da Pesquisa Nacional por Amostra de Domicílios no período de 1998 a 2003 para a estimativa das taxas de cobertura de linhas telefônicas residenciais nas cinco regiões geográficas brasileiras. Utilizou-se a regressão logística múltipla para identificar os fatores associados à posse de linha telefônica fixa. O impacto do vício nos intervalos com 95% de confiança foi avaliado em função da precisão alcançada em cada situação. RESULTADOS: Nas regiões metropolitanas Sudeste, Sul e Centro-Oeste com 70% e mais de cobertura, os vícios associados foram considerados desprezíveis. Nas demais regiões, os vícios relativos estavam acima do limite aceitável (0,4), indicando possíveis erros nas inferências construídas sob intervalo com 95% de confiança. A chance de acesso à linha telefônica residencial foi maior para população com cor da pele branca e maior escolaridade. CONCLUSÕES: Os achados mostram que o uso de cadastro de linhas telefônicas residenciais é indicado para a realização de inquéritos epidemiológicos apenas para estados com cobertura acima de 70%. Metodologias específicas para o tratamento de estimativas obtidas em localidades com taxas inferiores, precisam ser estudadas e divulgadas

Potential vectors and hosts of rickettsia spp: epidemiological studies in the Vale do Paraíba, state of Rio de Janeiro/Brazil

FAPESP, CNPq, CAPES

Power Secant Method applied to natural frequency extraction of Timoshenko beam structures

This work deals with an improved plane frame formulation whose exact dynamic stiffness matrix (DSM) presents, uniquely, null determinant for the natural frequencies. In comparison with the classical DSM, the formulation herein presented has some major advantages: local mode shapes are preserved in the formulation so that, for any positive frequency, the DSM will never be ill-conditioned; in the absence of poles, it is possible to employ the secant method in order to have a more computationally efficient eigenvalue extraction procedure. Applying the procedure to the more general case of Timoshenko beams, we introduce a new technique, named ""power deflation"", that makes the secant method suitable for the transcendental nonlinear eigenvalue problems based on the improved DSM. In order to avoid overflow occurrences that can hinder the secant method iterations, limiting frequencies are formulated, with scaling also applied to the eigenvalue problem. Comparisons with results available in the literature demonstrate the strength of the proposed method. Computational efficiency is compared with solutions obtained both by FEM and by the Wittrick-Williams algorithm.

Energy spectra for quantum wires and two-dimensional electron gases in magnetic fields with Rashba and Dresselhaus spin-orbit interactions

We introduce an analytical approximation scheme to diagonalize parabolically confined two-dimensional (2D) electron systems with both the Rashba and Dresselhaus spin-orbit interactions. The starting point of our perturbative expansion is a zeroth-order Hamiltonian for an electron confined in a quantum wire with an effective spin-orbit induced magnetic field along the wire, obtained by properly rotating the usual spin-orbit Hamiltonian. We find that the spin-orbit-related transverse coupling terms can be recast into two parts W and V, which couple crossing and noncrossing adjacent transverse modes, respectively. Interestingly, the zeroth-order Hamiltonian together with W can be solved exactly, as it maps onto the Jaynes-Cummings model of quantum optics. We treat the V coupling by performing a Schrieffer-Wolff transformation. This allows us to obtain an effective Hamiltonian to third order in the coupling strength k(R)l of V, which can be straightforwardly diagonalized via an additional unitary transformation. We also apply our approach to other types of effective parabolic confinement, e. g., 2D electrons in a perpendicular magnetic field. To demonstrate the usefulness of our approximate eigensolutions, we obtain analytical expressions for the nth Landau-level g(n) factors in the presence of both Rashba and Dresselhaus couplings. For small values of the bulk g factors, we find that spin-orbit effects cancel out entirely for particular values of the spin-orbit couplings. By solving simple transcendental equations we also obtain the band minima of a Rashba-coupled quantum wire as a function of an external magnetic field. These can be used to describe Shubnikov-de Haas oscillations. This procedure makes it easier to extract the strength of the spin-orbit interaction in these systems via proper fitting of the data.

Synthesis of PID controllers for a class of time delay systems

In this paper we use the Hermite-Biehler theorem to establish results on the design of proportional plus integral plus derivative (PID) controllers for a class of time delay systems. Using the property of interlacing at high frequencies of the class of systems considered and linear programming we obtain the set of all stabilizing PID controllers. As far as we know, previous results on the synthesis of PID controllers rely on the solution of transcendental equations. This paper also extends previous results on the synthesis of proportional controllers for a class of delay systems Of retarded type to a larger class of delay systems. (C) 2009 Elsevier Ltd. All rights reserved.

Analytical solutions for geometrically nonlinear trusses

This paper presents an analytical method for analyzing trusses with severe geometrically nonlinear behavior. The main objective is to find analytical solutions for trusses with different axial forces in the bars. The methodology is based on truss kinematics, elastic constitutive laws and equilibrium of nodal forces. The proposed formulation can be applied to hyper elastic materials, such as rubber and elastic foams. A Von Mises truss with two bars made by different materials is analyzed to show the accuracy of this methodology.

A contribution to the exact modal solution of in-plane beam structures

The exact vibration modes and natural frequencies of planar structures and mechanisms, comprised Euler-Bernoulli beams, are obtained by solving a transcendental. nonlinear, eigenvalue problem stated by the dynamic stiffness matrix (DSM). To solve this kind of problem, the most employed technique is the Wittrick-Williams algorithm, developed in the early seventies. By formulating a new type of eigenvalue problem, which preserves the internal degrees-of-freedom for all members in the model, the present study offers an alternative to the use of this algorithm. The new proposed eigenvalue problem presents no poles, so the roots of the problem can be found by any suitable iterative numerical method. By avoiding a standard formulation for the DSM, the local mode shapes are directly calculated and any extension to the beam theory can be easily incorporated. It is shown that the method here adopted leads to exact solutions, as confirmed by various examples. Extensions of the formulation are also given, where rotary inertia, end release, skewed edges and rigid offsets are all included. (C) 2008 Elsevier Ltd. All rights reserved.

KANT E A ADMIRAÇÃO DA NATUREZA

RESUMO: O parágrafo 62 da Crítica do Juízo, cuja função é definir o conceito de conformidade a fins objetiva (objektive Zweckmässigkeit), começa com uma declaração do filósofo segundo a qual todas as figuras geométricas se relacionam com uma conformidade a fins objetiva e admirável. Embora não seja aqui essencial para a definição do princípio dessa conformidade a fins, a afirmação de Kant de que ela é muitas vezes digna de admiração exerce um importante papel para a sua própria definição. O objetivo deste texto é tecer algumas considerações em torno dessa relação entre o princípio estritamente lógico da conformidade a fins e o sentimento em geral, seja de admiração da natureza, ou em todas as suas variações, tais como aparece na sequência do mesmo parágrafo 62: o entusiasmo, a alegria e a estupefação. Embora de antemão se reconheça que tais sentimentos não podem intervir no mecanismo estritamente lógico desse princípio, que, segundo Kant, é transcendental, pretende-se mostrar como o seu uso relaciona-se sempre e de algum modo com um sentimento. Para isso, é preciso mostrar que a afirmação de Kant segundo a qual o juízo teleológico não possui nenhuma relação com o sentimento de prazer e desprazer não implica necessariamente que esse tipo de juízo não possua relação nenhuma como nenhum tipo de sentimento.