Análise espectral de reflectarrays com substratos de duas camadas dielétricas anisotrópicas uniaxiais

Recently, an amazing development has been observed in telecommunication systems. Two good examples of this development are observed in mobile communication and aerospace systems. This impressive development is related to the increasing need for receiving and transmitting communication signals. Particularly, this development has required the study of new antennas and filters. This work presents a fullwave analysis of reflectarrays. The considered structures are composed by arrays of rectangular conducting patches printed on multilayer dieletric substrates, that are mounted on a ground plane. The analysis is developed in the spectral domain, using an equivalent transmission line method in combination with Galerkin method. Results for the reflection coefficient of these structures are presented and compared to those available in the literature. A good agreement was observed. Particularly, the developed analysis uses the transmission lines theory in combination with the incident potentials and the field continuity equations, at the structures interfaces, for obtaining the scattered field components expressions as function of the patch surface currents and of the incident field. Galerkin method is used to determine the unknown coefficients in the boundary value problem. Curves for the reflection coefficient of several reflectarray geometries are presented as function of frequency and of the structural parameters

Localização de um robô móvel usando odometria e marcos naturais

Several methods of mobile robot navigation request the mensuration of robot position and orientation in its workspace. In the wheeled mobile robot case, techniques based on odometry allow to determine the robot localization by the integration of incremental displacements of its wheels. However, this technique is subject to errors that accumulate with the distance traveled by the robot, making unfeasible its exclusive use. Other methods are based on the detection of natural or artificial landmarks present in the environment and whose location is known. This technique doesnt generate cumulative errors, but it can request a larger processing time than the methods based on odometry. Thus, many methods make use of both techniques, in such a way that the odometry errors are periodically corrected through mensurations obtained from landmarks. Accordding to this approach, this work proposes a hybrid localization system for wheeled mobile robots in indoor environments based on odometry and natural landmarks. The landmarks are straight lines de.ned by the junctions in environments floor, forming a bi-dimensional grid. The landmark detection from digital images is perfomed through the Hough transform. Heuristics are associated with that transform to allow its application in real time. To reduce the search time of landmarks, we propose to map odometry errors in an area of the captured image that possesses high probability of containing the sought mark

Planejamento cooperativo de tarefas em um ambiente de futebol de robôs

Este trabalho apresenta o desenvolvimento de um método de coordenação e cooperação para uma frota de mini-robôs móveis. O escopo do desenvolvimento é o futebol de robôs. Trata-se de uma plataforma bem estruturada, dinâmica e desenvolvida no mundo inteiro. O futebol de robôs envolve diversos campos do conhecimento incluindo: visão computacional, teoria de controle, desenvolvimento de circuitos microcontrolados, planejamento cooperativo, entre outros. A título de organização os sistema foi dividido em cinco módulos: robô, visão, localização, planejamento e controle. O foco do trabalho se limita ao módulo de planejamento. Para auxiliar seu desenvolvimento um simulador do sistema foi implementado. O simulador funciona em tempo real e substitui os robôs reais. Dessa forma os outros módulos permanecem praticamente inalterados durante uma simulação ou execução com robôs reais. Para organizar o comportamento dos robôs e produzir a cooperação entre eles foi adotada uma arquitetura hierarquizada: no mais alto nível está a escolha do estilo de jogo do time; logo abaixo decide-se o papel que cada jogador deve assumir; associado ao papel temos uma ação específica e finalmente calcula-se a referência de movimento do robô. O papel de um robô dita o comportamento do robô na dada ocasião. Os papéis são alocados dinamicamente durante o jogo de forma que um mesmo robô pode assumir diferentes papéis no decorrer da partida

Modelagem linear e identificação do modelo dinâmico de um robô móvel com acionamento diferencial

This work presents a modelling and identification method for a wheeled mobile robot, including the actuator dynamics. Instead of the classic modelling approach, where the robot position coordinates (x,y) are utilized as state variables (resulting in a non linear model), the proposed discrete model is based on the travelled distance increment Delta_l. Thus, the resulting model is linear and time invariant and it can be identified through classical methods such as Recursive Least Mean Squares. This approach has a problem: Delta_l can not be directly measured. In this paper, this problem is solved using an estimate of Delta_l based on a second order polynomial approximation. Experimental data were colected and the proposed method was used to identify the model of a real robot

Desenvolvimento de um rastreador solar do tipo polar com ajuste do ângulo de inclinação

The use of solar energy for electricity generation has shown a growing interest in recent years. Generally, the conversion of solar energy into electricity is made by PV modules installed on fixed structures, with slope determined by the latitude of the installation site. In this sense, the use of mobile structures with solar tracking, has enabled increased production of the generated energy. However, the performance of these structures depends on the type of tracker and the position control used. In this work, it is proposed position control a strategy applied for a solar tracker, which will be installed in Laboratory of Power Electronics and Renewable Energy (LEPER), located in the Federal University of Rio Grande do Norte (UFRN). The tracker system is of polar type with daily positioning east-west and tilt angle manual adjustment in the seasonal periods, from north to south

Controle de posição com restrição à orientação de um Veículo Aéreo Não-Tripulado tipo Quadrirrotor

Quadrotors aircraft are composed by four propellers mounted on four engines on a cross or x disposition, and, in this structure, the engines on the same arm spin in the same direction and the other arm in the opposite direction. By rotating each helix generates vertical upward thrust. The control is done by varying the rotational speed of each motor. Among the advantages of this type of vehicle can cite the mechanical simplicity of construction, the high degree of maneuverability and the ability to have vertical takeoffs and landings. The modeling and control of quadrirrotores have been a challenge due to problems such as nonlinearity and coupling between variables. Several strategies have been developed to control this type of vehicle, from the classical control to modern. There are air surveillance applications where a camera is fixed on the vehicle to point forward, where it is desired that the quadrotor moves at a fixed altitude toward the target also pointing forward, which imposes an artificial constraint motion, because it is not desired that it moves laterally, but only forwards or backwards and around its axes . This restriction is similar to the naturally existing on robots powered by wheels with differential drive, which also can not move laterally, due to the friction of the wheels. Therefore, a position control strategy similar to that used in this type of robot could be adapted for aerial robots like quadrotor. This dissertation presents and discusses some strategies for the control of position and orientation of quadrotors found in the literature and proposes a strategy based on dynamic control of mobile robots with differential drive, called the variable reference control. The validity of the proposed strategy is demonstrated through computer simulations

Análise espectral de reflectarrays com substrato de duas camadas dielétricas anisotrópicas uniaxiais

Recently, an amazing development has been observed in telecommunication systems. Two good examples of this development are observed in mobile communication and aerospace systems. This impressive development is related to the increasing need for receiving and transmitting communication signals. Particularly, this development has required the study of new antennas and filters. This work presents a fullwave analysis of reflectarrays. The considered structures are composed by arrays of rectangular conducting patches printed on multilayer dieletric substrates, that are mounted on a ground plane. The analysis is developed in the spectral domain, using an equivalent transmission line method in combination with Galerkin method. Results for the reflection coefficient of these structures are presented and compared to those available in the literature. A good agreement was observed. Particularly, the developed analysis uses the transmission lines theory in combination with the incident potentials and the field continuity equations, at the structures interfaces, for obtaining the scattered field components expressions as function of the patch surface currents and of the incident field. Galerkin method is used to determine the unknown coefficients in the boundary value problem. Curves for the reflection coefficient of several reflectarray geometries are presented as function of frequency and of the structural parameters

Protótipo de uma unidade com tri-geração de energia para utilizações remotas: aplicação de módulo secondutivo gerador termoelétrico

The generation for termoeletricity is characterized as a solid process of conversion of thermal energy (heat) in electric without the necessity of mobile parts. Although the conversion process is of low efficiency the system presents high degree of trustworthiness and low requisite of maintenance and durability. Its principle is based on the studies of termogeneration carried through by Thomas Seebeck in 1800. The frank development of the technologies of solid state for termoeletricity generation, the necessity of the best exploitation of the energy, also with incentive the cogeneration processes, the reduction of the ambient impact allies to the development of modules semiconductors of high efficiency, converge to the use of the thermoeletric generation through components of solid state in remote applications. The work presents the development, construction and performance evaluation of an prototype, in pilot scale, for energy tri-generation aiming at application in remote areas. The unit is composed of a gas lamp as primary source of energy, a module commercial semiconductor for thermoelectric generation and a shirt for production of the luminosity. The project of the device made compatible a headstock for adaptation in the gas lamp, a hot source for adaptation of the module, an exchanger of to be used heat as cold source and to compose first stage of cogeneration, an exchanger of tubular heat to compose second stage of cogeneration, the elaboration of a converter dc-dc type push pull, adequacy of a system of acquisition of temperature. It was become fullfilled assembly of the prototype in group of benches for tests and assay in the full load condition in order to evaluate its efficiency, had been carried through energy balance of the unit. The prototype presented an electric efficiency of 0,73%, thermal of 56,55%, illumination of 1,35% and global of 58,62%. The developed prototype, as the adopted methodology of assay had also taken care of to the considered objectives, making possible the attainment of conclusive results concerning to the experiment. Optimization in the system of setting of the semicondutor module, improvement in the thermal insulation and design of the prototype and system of protection to the user are suggestions to become it a commercial product

Análise estatística das emissões de CO e HC produzidas por gases da exaustão veicular oriundos de gasolina, GNV e mistura álcool/gasolina

The vehicles are the main mobile sources of carbon monoxide (CO) and unburned hydrocarbons (HC) released into the atmosphere. In the last years the increment of the fleet of vehicles in the municipal district of Natal-RN it is contributing to the increase of the emissions of those pollutants. The study consisted of a statistical analysis of the emissions of CO and HC of a composed sample for 384 vehicles with mechanization Gasoline/CNG or Alcohol/Gasoline/CNG of the municipal district of Natal-RN. The tests were accomplished in vehicles submitted to Vehicular Safety's Inspection, in the facilities of INSPETRANS, Organism of Vehicular Inspection. An partial gases analyzer allowed to measure, for each vehicle, the levels of CO and HC in two conditions of rotation of the motor (900 and 2500 rpm). The statistical analysis accomplished through the STATISTICA software revealed a sensitive reduction in the efficiency of the converters catalytic after 6 years of use with emission average it is of 0,78% of CO and 156 (ppm) of HC, Which represents approximately 4 (four) times the amount of CO and the double of HC in comparison with the newest vehicles. The result of a Student s t-test, suggests strongly that the average of the emissions of HC (152 ppm), at 900 rpm, is 40% larger than at 2500 rpm, for the motor without load. This result reveals that the efficiency of the catalytic conversion is limited kinetically in low engine speeds. The Study also ends that when comparing the emissions of CO and HC considering the influence of the fuels, it was verified that although the emissions of CO starting from CNG are 62% smaller than arising from the gasoline, there are not significant differences among the emissions of HC originating from of CNG and of the gasoline. In synthesis, the results place the current criteria of vehicular inspection, for exhaust gases, in doubt, leading the creation of emission limits of pollutant more rigorous, because the efficiency of the converters catalytic is sensibly reduced starting from 6 years of use. It is also raised the possibility of modifications in the test conditions adopted by the current norms, specifically in the speed engine, have seen that in the condition without load the largest emission indexes were registered in slow march. That fact that allows to suggest the dismissal of the tests in high speed engine, reducing the time of inspection in half and generating economy of fuel

Simulação computacional da interação fluido-estrutura em bombas de cavidades progressivas

The pumping through progressing cavities system has been more and more employed in the petroleum industry. This occurs because of its capacity of elevation of highly viscous oils or fluids with great concentration of sand or other solid particles. A Progressing Cavity Pump (PCP) consists, basically, of a rotor - a metallic device similar to an eccentric screw, and a stator - a steel tube internally covered by a double helix, which may be rigid or deformable/elastomeric. In general, it is submitted to a combination of well pressure with the pressure generated by the pumping process itself. In elastomeric PCPs, this combined effort compresses the stator and generates, or enlarges, the clearance existing between the rotor and the stator, thus reducing the closing effect between their cavities. Such opening of the sealing region produces what is known as fluid slip or slippage, reducing the efficiency of the PCP pumping system. Therefore, this research aims to develop a transient three-dimensional computational model that, based on single-lobe PCP kinematics, is able to simulate the fluid-structure interaction that occurs in the interior of metallic and elastomeric PCPs. The main goal is to evaluate the dynamic characteristics of PCP s efficiency based on detailed and instantaneous information of velocity, pressure and deformation fields in their interior. To reach these goals (development and use of the model), it was also necessary the development of a methodology for generation of dynamic, mobile and deformable, computational meshes representing fluid and structural regions of a PCP. This additional intermediary step has been characterized as the biggest challenge for the elaboration and running of the computational model due to the complex kinematic and critical geometry of this type of pump (different helix angles between rotor and stator as well as large length scale aspect ratios). The processes of dynamic generation of meshes and of simultaneous evaluation of the deformations suffered by the elastomer are fulfilled through subroutines written in Fortan 90 language that dynamically interact with the CFX/ANSYS fluid dynamic software. Since a structural elastic linear model is employed to evaluate elastomer deformations, it is not necessary to use any CAE package for structural analysis. However, an initial proposal for dynamic simulation using hyperelastic models through ANSYS software is also presented in this research. Validation of the results produced with the present methodology (mesh generation, flow simulation in metallic PCPs and simulation of fluid-structure interaction in elastomeric PCPs) is obtained through comparison with experimental results reported by the literature. It is expected that the development and application of such a computational model may provide better details of the dynamics of the flow within metallic and elastomeric PCPs, so that better control systems may be implemented in the artificial elevation area by PCP

Desenvolvimento de um sistema para aplicação dos conceitos da tecnologia cad3d-bim na indústria moveleira

In this work was developed an information system to apply the concepts of CAD3D-BIM technology for the design activities of the furniture industry. The development of this system was based in an architecture comprised of two modules: a web interface to management the metadata of models from furniture's library and the combination of three-dimensional CAD software with a specific plugin to access the information from this model. To develop this system was also used a Data Base Management System (DBMS) designed to storage the information from models in a hierarchical way, based on concepts of Group Technology (GT). The centralization of information in a single database allows the automatic availability of any changes to all participants involved in a particular project when it‟s happens. Each module from system has its own connection to this database. Finally was developed a prototype from a 3D virtual environment to help create Virtual Reality projects in the web. A study from available technologies to create 3D web applications for execution in websites was done to support this development. The interconnection between modules and the database developed allowed the assembly of a system architecture to support the construction and exhibition of projects of the furniture industry in accordance with the concepts proposed by BIM (Building Information Modeling), using as object of study the furniture industry of state of Rio Grande do Norte

Estudo de um compósito de matriz cerâmica com carga de recicláveis para o uso na construção civi

With a view to revitalizing public environments through criteria that include economy, tourism, aesthetics and respect for the environment, this paper proposes a model of kiosk manufactured with composite material blocks, to be employed as a public instrument. . The model consists of a structure composed of planned blocks and manufactured in cement-based composite, gypsum, ground and water, having the styrofoam inside filled with pet bottles of 500 ml dose. The social and environmental issue is the critical point of the work when it can, through the reuse of environmentally harmful materials such as polyethylene terephthalate PET, using such modules for the construction of various areas of Commerce, promoting the protection of the environment combined with the improvement of the quality of life of the population. The tourism factor, which is significant in the economy of the North, is also considered as the modulated kiosk has a visual aspect innovative and differentiated. The environmental issue is addressed by encouraging the reuse of PET material and EPS (polystyrene)

O leitor universitário e a construção das práticas de ler e escrever textos impressos e digitais

The construction of a mapping of the practices of reading and writing printed and digital texts, declared by graduating students from the Bachelor s degree in Science and Technology (BCT), has provided us the analysis of the course they are making in such a socio-historical moment characterized by the revolution of the post-paper. In this sense, the general objective of this research is to understand how that construction works under the point of view of those graduating students. For this, our reflection has been guided by the search of answers for some questions which have presented to us: what reading and writing conceptions BCT graduating students have; what reading and writing practices those collaborators develop; what collections they declare to have access to; what differences they declare to have between printed and digital reading and writing along the different social roles they develop; what the reader/writer identity relations of those collaborators are. To achieving the plausible answers, we have gathered a corpus composed by texts of three genres of the argument order: academic profiles (or self-portrait), opinion articles and argumentative letters. Besides, we have made semi-structured interviews and questionnaires in the online tool of the Google Docs. The methodology which supports this academic work is the qualitative research (SIGNORINI; CAVALCANTI, 1998)of ethnographic direction (THOMAS, 1993; ANDRÉ, 1995) in Applied Linguistics (CELANI, 2000; MOITA-LOPES, 2006) and the theoretical contribution comes from the bakhtinian perspective of language conception (BAKHTIN [1929] 1981); the socio-historical writing construction (LÉVY, 1996; CHARTIER, R., 1998, 2002, 2007; COSCARELLI, 2006; CHARTIER, A., 2007; ARAÚJO, 2007; COSCARELLI; RIBEIRO, 2007; XAVIER, 2009; MARCUSCHI; XAVIER, 2010); from the studies of the pedagogy of the writing (GIROUX, 1997); from the literacy studies understood as sociocultural practice, plural and situated (TFOUNI, 1988; KLEIMAN, 1995; TINOCO, 2003, 2008; OLIVEIRA; KLEIMAN, 2008), from the studies about identity in postmodernity (HALL, 2003; BAUMAN, 2005). The results of the analysis have pointed at a multiplicity of reading/writing practices of printed and digital texts developed by the BCT graduating students due to the coexistence of the modality printed and that one derived from the new mobile devices. In that multiplicity, the prevalent idea of the collaborators is that there is a continuum between printed texts and digital texts (not a dichotomy), since the option of reading/writing printed texts or digital ones is always linked to specific communication situations, which involve participants, objectives, strategies, values, (dis)advantages, besides (re)creation of discursive genres in function of the mobile devices to which those collaborators have access in the different spheres of activities that they participate. All of that has caused a deep intersection in the identity traces of college students readers/writers in the 21st century which cannot be ignored by academic formation

O ser elástico, mola, agulha, trepidação: expressões do homoerotismo em Fernando Pessoa

This Masters thesis investigates and analyzes the homoerotic expressions in Fernando Pessoa s poetry and in his heteronyms : Álvaro de Campos, Alberto Caeiro and Ricardo Reis. Through the elaboration of deceptive strategies as a way to escape from the insults and the constraints, the poet by means of creative runaway lines builds up a homoerotic poetry that differ from the established patterns and representational models of the literature. We can find, bearing in mind a problematic sexuality which overflows in the various I s, of the sinuous identities and the movable boundaries, and intense mask games. They become real in poems, especially by means of sensations, yielding the possibility of a queer discourse and generating a homoerotic poetry. Pessoa s homoerotism is, thus, presented amid friendly relationships, smooth spaces, of heterotrophy of the city, or others space and the closet s aesthetics. Based on this, it is noted the articulations of a performance gender as body scripture and inscription, thus establishing a physical-writing which reveals a transgressive sexuality, with multiple entrances and exits, affirmations and denials that originate paradoxes. In this matter, we develop links between Foucault conceptions (2010a, 2010b, 2011) towards the history of sexuality, friendship and the power-knowledge relations with traces of significance and subjectivity, in processes of faciality and BwO (Body-without-Organs) in Deleuze and Guattari (1996). We still consider the ontological questionings towards the Gay dimension in Eribon (2008) and we raise aspects concerning the construction of the idea of masculinity in Bourdieu (2010). Finally, we base ourselves on Sedgwick s 1993 closet epistemological approach, as well as on Butler s 2012 gender and performance theory, also going through a few Bataille 1987 passages about erotism, that redimension the homoaffective images of the Portuguese poet

Uso de replicação móvel para distribuição de vídeo digital em redes de computadores

A maioria da soluções apresentadas como candidatas à implementação de serviços de distribuição de áudio e vídeo, têm sido projetadas levando-se em consideração determinadas condições de infra-estrutura, formato dos fluxos de vídeo a serem transmitidos, ou ainda os tipos de clientes que serão atendidos pelo serviço. Aplicações que utilizam serviços de distribuição de vídeo normalmente precisam lidar com grandes oscilações na demanda pelo serviço devido a entrada e saída de usuários do serviço. Com exemplo, basta observar a enorme variação nos níveis de audiência de programas de televisão. Este comportamento coloca um importante requisito para esta classe de sistemas distribuídos: a capacidade de reconfiguração como conseqüência de variações na demanda. Esta dissertação apresenta um estudo que envolveu o uso de agentes móveis para implementar os servidores de um serviço de distribuição de vídeo denominada DynaVideo. Uma das principais características deste serviço é a capacidade de ajustar sua configuração em conseqüência de variações na demanda. Como os servidores DynaVideo podem replicar-se e são implementados como código móvel, seu posicionamento pode ser otimizado para atender uma dada demanda e, como conseqüência, a configuração do serviço pode ser ajustada para minimizar o consumo de recursos necessários para distribuir vídeo para seus usuários. A principal contribuição desta dissertação foi provar a viabilidade do conceito de servidores implementados como agentes móveis Java baseados no ambiente de desenvolvimento de software Aglet.