Estudo do comportamento no estado fresco e endurecido do concreto com incorporação de resíduo de corte de botão

This works aims at investigating the effects of adding waste from RCBP-polyester button manufacturing to Portland cement concrete, particularly regarding its consistency and mechanic strength. The RCBP used came from a button factory located in Parnamirim, RN, Brazil. The waste was added to the concrete on different ratios: 5 %, 10 %, 15 % and 20 % of the total cement mass. A sample of concrete without the RCBP was used as reference, 1:1,33:2,45:0,50. For the mechanic strength test four samples were tested with different ages (3, 7 and 28 days old) and mixtures. Furthermore, a Slump Test was also conducted in order to verify the concrete s consistency. A tendency to a reduction in the compression resistance was noticed for all samples. For the samples with 5 % and 10 %, there was also an increase in the traction resistance during inflexion, regarding the reference concrete. In the microstructural analysis, the RBCP was observed to show an irregular and porous surface, thus explaining the consistency decrease

Uso fertilizante de resíduo da indústria processadora de goiabas

O resíduo da indústria processadora de goiabas vem sendo aplicado em algumas áreas, entretanto não é conhecido o seu efeito na fertilidade do solo. Foi realizado experimento em casa de vegetação, com o objetivo de avaliar o efeito da aplicação do resíduo da indústria processadora de goiabas na fertilidade do solo, tendo como planta-teste o milho. O delineamento experimental utilizado foi em blocos ao acaso, em esquema fatorial 5x2, com quatro repetições, combinando-se cinco doses do resíduo da indústria processadora de goiabas (0; 20; 40; 60 e 80 t ha-1) na presença e ausência de adubação mineral. A adição de resíduo da indústria processadora de goiabas propiciou aumento nos teores de P e K do solo. O resíduo da indústria processadora de goiabas é uma fonte de liberação lenta de N e P para as plantas.

Mineralização do nitrogênio proveniente da aplicação do resíduo da indústria processadora de goiabas em Argissolo

Informações sobre a mineralização de subprodutos são importantes para o correto manejo desses materiais em áreas agrícolas. Assim, objetivou-se avaliar a mineralização do nitrogênio proveniente do resíduo da indústria processadora de goiabas, aplicado em Argissolo cultivado com goiabeiras. Amostras do solo mais o subproduto foram acondicionados em frascos de polietileno com capacidade de 0,25 dm³. Foram pesados 100 g de solo mais o resíduo referente a cada tratamento (doses do subproduto: 0; 9; 18 e 36 t ha-1), sendo tal procedimento realizado em triplicata. O período máximo de incubação foi de 11 semanas, analisando-se as amostras nos seguintes tempos: 0; 7; 14; 28; 42; 56; 70; 84; 98; 112 e 126 dias. A umidade foi corrigida para 70% da capacidade de retenção de água do solo, sendo monitorada diariamente através de pesagens dos potes. Nos tempos estabelecidos realizou-se a desmontagem de três frascos correspondentes a cada tratamento, determinando-se o nitrogênio inorgânico. Pode-se afirmar que a mineralização do N ou a liberação é lenta, ou seja, não há rápida disponibilização de nitrogênio. No período avaliado, 126 dias, a fração média de mineralização foi de 23% e, a meia vida média de 73 dias.

Desempenho de argamassas produzidas com agregados reciclados oriundos do resíduo de construção e demolição da Grande Natal-RN

The construction industry is responsible for generating a lot of waste because of their activities. Consequently, it is noticeable the occurrence of environmental problems in terms of its disposal in inappropriate places. Faced with this problem, some studies have been conducted with the aim of developing technologies and alternatives for recycling construction and demolition waste (CDW), motivated by the scarcity of natural resources and reduction of environmental problems generated. The research aims to characterize the recycled aggregates derived from construction and demolition waste (CDW) produced in the Greater Natal-RN and analyze the performance of mortar coating produced with recycled aggregates. The study includes the chemical , physical and microstructural characterization of recycled aggregates , as well as conducting microscopic analysis and laboratory tests in the fresh state (consistency index , water retention , bulk density and content of entrained air ) and in the hardened state ( compressive strength , tensile strength in bending , water absorption by immersion and capillary , mass density and void ratio ) for mortars produced from different levels of substitution of aggregates ( 0, 20 %, 40 %, 60 %, 80 % and 100 %). The results were satisfactory, providing mortars produced with recycled aggregates, smaller mass density and dynamic modulus values as well as an increase in the rates of absorption and porosity. The tensile strength in bending and compression for TP1 (1:2:8) trait were lower for mortars produced with recycled aggregates and the best result was 20% for replacement. For the TP2 (1:8) mapping, there was an increase in resistance to traction and compression and the best result was for 100% replacement of natural aggregates by recycled. The experiments led to the conclusion that the technical and economic point of view that the mortars produced with recycled aggregates can be used in construction, only if there is an effective control in production processes of recycled aggregate and at the dosage of mortars

Um estudo da aplicação do conceito de risco na conscientização e conhecimento de estudantes de ensino técnico sobre riscos de segurança e saúde ocupacional em laboratório de soldagem

This dissertation presents a discussion on the level of risk awareness of students who have welding practice in the laboratories at CEFET/PI, both in Teresina and Floriano. Its main goal is to investigate risk factors involving students, teachers and employees that work in these laboratories. It s an empirical survey, held among a certain amount of students from the course in Mechanic Technology. For data analysis, the concept of risk was compared to the students direct measure of perception. The main results suggest the students must be better informed, more risk aware and more competent, in order to avoid accidents. They also point to a strong need for a more formal and effective performance to assure full consciousness about the risks involving the welding practice.

Massa de forragem, composição morfológica e química de capim-tanzânia sob diferentes dias de descanso e altura de resíduo pós-pastejo

The experiment was conducted at UNESP/FCAV, Jaboticabal, SP, with the objective of evaluating the influence of the rest period and height of the residue post-grazing on the dry matter mass, morphologic composition and on the chemical composition of the Tanzania-grass pre-grazing condition, under rotational grazing. The treatments consisted of the combination of two rest periods (25 and 35 days) and two residue height post-grazing (30 and 50 cm), as a complete randomized design in factorial arrangement 2 x 2, with three replications, with the grazing cycles considered as sub plots. The herbage mass of stem, leaves, dead material and the leaf: stem ratio were significantly influenced (P<0.05) by the grazing cycles. The percentage of CP in the leaf and stem and the NDF in the stem, leaf and whole plant were influenced positively (P<0.05) by the grazing cycles. It was observed that the short rest periods associated with the smallest residue height post-grazing presented the best results in terms of herbage mass and chemical characteristics of the herbage.

Digestibilidade in vitro/gás de volumosos exclusivos ou combinados avaliados pelo resíduo remanescente da digestão da matéria seca e produção de gás

Foi avaliada a digestibilidade in vitro/gás da matéria seca (MS) de quatro volumosos, exclusivos e suas combinações, na proporção de 50% na MS. Foram incubados 100 mg de amostra por tratamento, em triplicatas, em 48 h de digestão. As digestibilidades da MS e a produção de gás foram: cana-de-açúcar = 60,6%, 17,3 mL; cana-de-açúcar + silagem de milho = 63,9%, 19,6 mL; cana-de-açúcar + capim-elefante com 60 dias = 60,5%, 16,9 mL; cana-de-açúcar + capim-elefante com 180 dias = 48,6%, 14,1 mL; silagem de milho = 66,3%; silagem de milho + capim-elefante com 60 dias = 62,1%, 16,7 mL; silagem de milho + capim-elefante com 180 dias = 52,7%, 15,8 mL; capim-elefante com 60 dias = 61,5%, 16,9 mL; capim-elefante com 180 dias = 34,6%, 11,7 mL. Constatou-se que a combinação de volumosos, em alguns casos, pode diminuir a digestibilidade da MS dos volumosos de melhor qualidade.

Valor nutritivo do resíduo do processamento do caroço de algodão suplementado com levedura e avaliado em bovinos

O objetivo neste trabalho foi avaliar o consumo, a digestibilidade total e parcial da matéria seca (MS) e dos nutrientes e os parâmetros ruminais de novilhos alimentados com rações à base de resíduo do processamento do caroço de algodão (RPCA) suplementado com levedura seca de cana-de-açúcar. Foram utilizados seis novilhos Nelore canulados no rúmen e duodeno, alimentados com rações compostas de 80% RPCA e 20% concentrado, composto de milho, ureia e levedura nos níveis de 0, 20 ou 40%. O delineamento experimental adotado para análise do consumo e da digestibilidade foi em blocos casualisados e a análise dos parâmetros ruminais foi em parcela subdividida. Os consumos e a digestibilidade de nutrientes não foram influenciados pela suplementação com levedura, fato que pode estar relacionado ao alto valor da fração C do resíduo do processamento do RPCA (44,51% MS) e à baixa fração proteica de lenta degradação da levedura, que impediu a sincronização energia/nitrogênio para maior degradação do resíduo. O pH do líquido ruminal decresceu linearmente nos animais mantidos com as dietas suplementadas com levedura. em todas as dietas, o pH e a concentração de N-NH3 foram adequados para o crescimento microbiano. As concentrações ruminais de acetato, propionato, butirato e ácidos graxos voláteis totais e a relação acetato:propionato não foram influenciadas pela suplementação com levedura. O resíduo do processamento do caroço de algodão é uma opção a ser utilizada no arraçoamento de bovinos.

Projeto e controle de um sistema de aquecimento no Laboratório de Avaliação de Medição em Petróleo

The Oil Measurement Evaluation Laboratory (LAMP), located in the Federal University of Rio Grande do Norte (UFRN), has as main goal to evaluate flow and BS&W meters, where the simulation of a bigger number of operation variable in field, guarantees a less uncertain evaluation. The objective of this work is to purpose a heating system design and implementation, which will control the temperature safely and efficiently in order to evaluate and measure it. Temperature is one of the variables which influence the flow and BS&W accurate measurement, directly affecting the fluid viscosity and density in the experiment. To project the heating system it is of great importance to take the laboratory requirements, conditions and current restrictions into consideration. Three alternatives were evaluated: heat exchanger, internal resistance and external resistance. After the analyses are made in order to choose the best alternative for the heating system in the laboratory, control strategies were determined for it, PID control methods in combination with fuzzy logic were used. Results showed a better performance with fuzzy logic than with classic PID

Sistemas de automação e supervisão do laboratório de avaliação dos processos de medição de vazão e BSW

During a petroleum well production process, It is common the slmultaneous oil and water production, in proportion that can vary from 0% up to values close to 100% of water. Moreover, the production flows can vary a lot, depending on the charaeteristies of eaeh reservoir. Thus being, the meters used in field for the flow and BSW (water in the oil) measurement must work well in wide bands of operation. For the evaluation of the operation of these meters, in the different operation conditions, a Laboratory will be built in UFRN, that has for objective to evaluate in an automatic way the processes of flow and BSW petroleum measurement, considering different operation conditions. The good acting of these meters is fundamental for the accuracy of the measures of the volumes of production liquid and rude of petroleum. For the measurement of this production, the petroleum companies use meters that should indicate the values with tha largast possible accuracy and to respect a series of conditions and minimum requirements, estabelished by the united Entrance ANP/INMETRO 19106/2000. The laboratory of Evafuation of the Processes of Measurement of Flow and BSW to be built will possess an oil tank basically, a tank of water, besides a mixer, a tank auditor, a tank for separation and a tank of residues for discard of fluids, fundamental for the evaluation of the flow metars and BSW. The whole process will be automated through the use of a Programmable Logicat Controller (CLP) and of a supervisory system.This laboratory besides allowing the evaluation of flow meters and BSW used by petroleum companies, it will make possible the development of researches related to the automation. Besides, it will be a collaborating element to the development of the Computer Engineering and Automation Department, that it will propitiate the evolution of the faculty and discente, qualifying them for a job market in continuous growth. The present work describes the project of automation of the laboratory that will be built at of UFRN. The system will be automated using a Programmable Logical Controller and a supervisory system. The programming of PLC and the screens of the supervisory system were developed in this work

Estudo da estimativa da incerteza de medição para determinação do BS&W e da vazão aplicado no laboratório de avaliação de medição do petróleo

The considered work presents the procedure for evaluation of the uncertainty related to the calibration of flow measurers and to BS&W. It is about a new method of measurement purposed by the conceptual project of the laboratory LAMP, at Universidade Federal do Rio Grande do Norte, that intends to determine the conventional true value of the BS&W from the total height of the liquid column in the auditor tank, hydrostatic pressure exerted by the liquid column, local gravity, specific mass of the water and the specific mass of the oil, and, to determine the flow, from total height of liquid column and transfer time. The calibration uses a automatized system of monitoration and data acquisition of some necessary largnesses to determine of flow and BS&W, allowing a better trustworthiness of through measurements

Aproveitamento de resíduo de caulim em cerâmica branca

The world market of Kaolin has been growing as new investments for better quality of materials have been applied. This market produces amounts of dross that are put in the environment in a wrong way, causing damages to it. Trying to reduce these damages, researches have been done in an attempt to use kaolin dross in ceramic. The disposal of kaolin dross in the environment by the industries of the states of Rio Grande do Norte and Paraiba have great impact in society. Usually this dross is disposed clandestinely in places like roads, river banks and lands of small cities. The present work shows the characteristics of the kaolin produced by the mining company in Junco do Seridó, Paraiba state, western Seridó, 300 km from Natal, in the border of both states. After that, researches were done to study its physical and the chemistry characteristics, trying to see if it can be used in white ceramic. The samples got were bolted in fabric of 325# . The technological characteristics tried to use it as a product in white ceramic. For that, it was made a haracterization of the subject matter through enlargement analyses, ATG and ATD, elaborating three formulations that were burned in four different temperatures, 1175, 1200, 1250 and 1300 degrees centigrade up to 30 minutes. After the burning, the subjects were submitted to water absorbing tests, linear retreating, apparent porosity, apparent specific mass, resistance to flexibility and MEV. For one of the mixtures it was obtained demanded properties for a semi porous material

Estudo do efeito da substituição de caulim por resíduo de caulim na fabricação de cerâmica de revestimento

Companies involved in kaolin mining and treatment represent an important area of industrial development in Brazil, significantly contribution to the worldwide production of such mineral. As a result, large volumes of kaolin residue are constantly generated and abandoned in the environment, negatively contributing to its preservation. In this scenario, the objective of the present study was to characterize the residue generated from kaolin mining as well as to assess its potential use as raw material for the production of ceramic tiles. Ceramic mixtures were prepared from raw materials characterized by X-ray fluorescence, X-ray diffraction, particle size analysis and thermal analysis. Three compositions were prepared using kaolin residue contents of 10%, 20% and 30%. Samples were uniaxially pressed, fired at 1200ºC and characterized aiming at establishing their mineralogical composition, water absorption, apparent porosity, specific mass, linear retraction and modulus of rupture. The results showed that the residue basically consisted of kaolinite and successfully replaced raw kaolin in the preparation of ceramic title formulations without significantly affecting the properties of the fired material

Efeito da introdução de resíduo de cinza de forno cerâmico em massa para cerâmica estrutural

The red ceramics and structural ceramics, as they are known, include ceramic materials made by blocks of seals and structures, bricks, tiles, smail flagstones manacles, rustic floors and ornamental materials. Their fabrication uses raw material such as clay and clay sites, with some content of impurity. It has good durability and mechanical strength to compression, low cost, making it one of the mainly used materials in civil engineering. The incorporation of many industrial activities residue to ceramic products is a technological alternative for reducing the environmental impact caused by its carefree disposal. This incorporation can promote chemical change and inertness of metals from residue, by fixation in the glassy phase of ceramic during the burning stage. The main aim of this project is to study the technical feasibility of the addition of ceramic oven ash into formulations of mass for structural ceramics. In this project two kinds of clay (plastic and non-plastic) were used, as well as the ash from firewood used in the process of burning of structural ceramics. A group of experiments was outlined, which permitted the evaluation of the influence of the burning cycle in different temperatures of the ash content in formulations for ceramic blocks through technological properties, mechanical behavior and microstructure. Five samples were processed of each one of the masses of plastic and non-plastic clay without addition of ash and with addition of ash on the percentages of 10 % and 20 %, for temperatures of 850 °C, 950 °C, 1050 °C and 1150 °C, obtained through sinterization process. Among the studied compositions, the one which presented best performance was the mass of clay with 10 % of ash, at temperature of 1150 °C, with the smallest absorption of water, the smallest apparent porosity, specific apparent mass a bit over the others and greatest mechanical resistance to flexion. The composition made confirmed the technical feasibility of the use of ash in the mass for structural ceramics with maintenance of its necessary characteristics for its purposes

Obtenção de placas cerâmico a partir de formulações de massas triaxiais de resíduos de caulim, chamote de telha e cinza vegetal

The production of red ceramic is an industrial activity that causes an intense impact. The manufacture of its products considerably increases the demand for natural resources, mainly with the extraction of raw material. The ceramic material produced generates waste, such as ash firewood and chamote. The residue from the beneficiation of kaolin is deposited in a poor, degrades the environment and contaminate water sources and soil, constituting in this manner, ecological disasters. The main objective of this work is to develop the formulation of a ceramic product consisting solely of industrial solid wastes, from ceramic tiles, (chamote) residue of kaolin and ash firewood. It is assumed that this product made in the laboratory can be used in coatings, wall and floor. The aim is to facilitate the replacement of the raw material of original composition of a ceramic body, for waste, while the process of production equal to the conventionally used, so that the properties of the product are reproduced. This work is characterized waste as its chemical composition, analysis of particle size, X-ray diffraction and thermal behavior. Several formulations were studied. The mass of waste was prepared by dry process, pressed to 25 MPa, and then burned in muffle type oven to 850, 950, 1050 and 1150 °C. The results showed that it is technically possible to produce porous tiles only with waste. It was found that the formulations of bodies play a key role in the properties of the final product, as well as the sintering temperature and heating rates. RN in the waste of kaolin is estimated at 15,000 t/month, about 3,000 gray t/month and chamote with 10 million pieces/month damaged. The presence of carbonates of calcium and magnesium at 1050 ° C results in an appropriate porosity and mechanical strength. The formulation M3JE, composed of 69% waste of kaolin, 7.7% and 23.3% of chamote of gray, became suitable for porous materials with the strength and absorption within the level of national and international standards