Switching of ferroelectric liquid crystal doped with cetyltrimethylammonium bromide-assisted CdS nanostructures

Large scale high yield cadmium sulfide (CdS) nanowires with uniform diameter were synthesized using a rapid and simple solvo-chemical and hydrothermal route assisted by the surfactant cetyltrimethylammonium bromide (CTAB). Unique CdS nanowires of different morphologies could be selectively produced by only varying the concentration of CTAB in the reaction system with cadmium acetate, sulfur powder and ethylenediamine. We obtained CdS nanowires with diameters of 64–65 nm and lengths of up to several micrometers. A comparative study of the optical properties of ferroelectric liquid crystal (FLC) Felix-017/100 doped with 1% of CdS nanowires was performed. Response times of the order of from 160 to 180 μs, rotational viscosities of the order of from 5000 to 3000 mN s m−2 and polarizations of the order of from 10 to 70 nC cm−2 were measured. We also observed an anti-ferroelectric to ferroelectric transition for CdS doped FLC instead of the ferroelectric to paraelectric transition for pure FLC.

Synthetic strategy of porous ZnO and CdS nanostructures doped ferroelectric liquid crystal and its optical behavior

A simple and scalable chemical approach has been proposed for the generation of 1-dimensional nanostructures of two most important inorganic materials such as zinc oxide and cadmium sulfide. By controlling the growth habit of the nanostructures with manipulated reaction conditions, the diameter and uniformity of the nanowires/nanorods were tailored. We studied extensively optical behavior and structural growth of CdS NWs and ZnO NRs doped ferroelectric liquid crystal Felix-017/100. Due to doping band gap has been changed and several blue shifts occurred in photoluminescence spectra because of nanoconfinement effect and mobility of charges.

Surface InGaAs nanostructures for sensing applications

El desarrollo de sensores está ganando cada vez mayor importancia debido a la concienciación ciudadana sobre el medio ambiente haciendo que su desarrollo sea muy elevado en todas las disciplinas, entre las que cabe destacar, la medicina, la biología y la química. A pesar de la existencia de estos dispositivos, este área está aún por mejorar, ya que muchos de los materiales propuestos hasta el momento e incluso los ya comercializados muestran importantes carencias de funcionamiento, eficiencia e integrabilidad entre otros. Para la mejora de estos dispositivos, se han propuesto diversas aproximaciones basadas en nanosistemas. Quizá, uno de las más prometedoras son las nanoestructuras de punto cuántico, y en particular los semiconductores III-V basados en la consolidada tecnología de los arseniuros, las cuáles ofrecen excelentes propiedades para su uso como sensores. Además, estudios recientes demuestran su gran carácter sensitivo al medio ambiente, la posibilidad de funcionalizar la superficie para la fabricación de sensores interdisciplinares y posibilididad de mejorar notablemente su eficiencia. A lo largo de esta tesis, nos centramos en la investigación de SQD de In0.5Ga0.5As sobre substratos de GaAs(001) para el desarrollo de sensores de humedad. La tesis abarca desde el diseño, crecimiento y caracterización de las muestras hasta la el posterior procesado y caracterización de los dispositivos finales. La optimización de los parámetros de crecimiento es fundamental para conseguir una nanoestructura con las propiedades operacionales idóneas para un fin determinado. Como es bien sabido en la literatura, los parámetros de crecimiento (temperatura de crecimiento, relación de flujos del elemento del grupo V y del grupo I II (V/III), velocidad de crecimiento y tratamiento térmico después de la formación de la capa activa) afectan directamente a las propiedades estructurales, y por tanto, operacionales de los puntos cuánticos (QD). En esta tesis, se realiza un estudio de las condiciones de crecimiento para el uso de In0.5Ga0.5As SQDs como sensores. Para los parámetros relacionados con la temperatura de crecimiento de los QDs y la relación de flujos V / I I I se utilizan los estudios previamente realizados por el grupo. Mientras que este estudio se centrará en la importancia de la velocidad de crecimiento y en el tratamiento térmico justo después de la nucleación de los QDs. Para ello, se establece la temperatura de creciemiento de los QDs en 430°C y la relación de flujos V/III en 20. Como resultado, los valores más adecuados que se obtienen para la velocidad de crecimiento y el tratamiento térmico posterior a la formación de los puntos son, respectivamente, 0.07ML/s y la realización de una bajada y subida brusca de la temperatura del substrato de 100°C con respecto a la temperatura de crecimiento de los QDs. El crecimiento a una velocidad lo suficientemente alta que permita la migración de los átomos por la superficie, pero a su vez lo suficientemente baja para que se lleve a cabo la nucleación de los QDs; en combinación con el tratamiento brusco de temperatura que hace que se conserve la forma y composición de los QDs, da lugar a unos SQDs con un alto grado de homogeneidad y alta densidad superficial. Además, la caracterización posterior indica que estas nanoestructuras de gran calidad cristalina presentan unas propiedades ópticas excelentes incluso a temperatura ambiente. Una de las características por la cual los SQD de Ino.5Gao.5As se consideran candidatos prometedores para el desarrollo de sensores es el papel decisivo que juega la superficie por el mero hecho de estar en contacto directo con las partículas del ambiente y, por tanto, por ser capaces de interactuar con sus moléculas. Así pues, con el fin de demostrar la idoneidad de este sistema para dicha finalidad, se evalúa el impacto ambiental en las propiedades ópticas y eléctricas de las muestras. En un primer lugar, se analiza el efecto que tiene el medio en las propiedades ópticas. Para dicha evaluación se compara la variación de las propiedades de emisión de una capa de puntos enterrada y una superficial en distintas condiciones externas. El resultado que se obtiene es muy claro, los puntos enterrados no experimentan un cambio óptico apreciable cuando se varían las condiciones del entorno; mientras que, la emisión de los SQDs se modifica significativamente con las condiciones del medio. Por una parte, la intensidad de emisión de los puntos superficiales desaparece en condiciones de vacío y decrece notablemente en atmósferas secas de gases puros (N2, O2). Por otra parte, la fotoluminiscencia se conserva en ambientes húmedos. Adicionalmente, se observa que la anchura a media altura y la longitud de onda de emisión no se ven afectadas por los cambios en el medio, lo que indica, que las propiedades estructurales de los puntos se conservan al variar la atmósfera. Estos resultados apuntan directamente a los procesos que tienen lugar en la superficie entre estados confinados y superficiales como responsables principales de este comportamiento. Así mismo, se ha llevado a cabo un análisis más detallado de la influencia de la calidad y composición de la atmósfera en las propiedades ópticas de los puntos cuánticos superficiales. Para ello, se utilizan distintas sustancias con diferente polaridad, composición atómica y masa molecular. Como resultado se observa que las moléculas de menor polaridad y más pesadas causan una mayor variación en la intensidad de emisión. Además, se demuestra que el oxígeno juega un papel decisivo en las propiedades ópticas. En presencia de moléculas que contienen oxígeno, la intensidad de fotoluminiscencia disminuye menos que en atmósferas constituidas por especies que no contienen oxígeno. Las emisión que se observa respecto a la señal en aire es del 90% y del 77%, respectivamente, en atmósferas con presencia o ausencia de moléculas de oxígeno. El deterioro de la señal de emisión se atribuye a la presencia de defectos, enlaces insaturados y, en general, estados localizados en la superficie. Estos estados actúan como centros de recombinación no radiativa y, consecuentemente, se produce un empeoramiento de las propiedades ópticas de los SQDs. Por tanto, la eliminación o reducción de la densidad de estos estados superficiales haría posible una mejora de la intensidad de emisión. De estos experimentos de fotoluminiscencia, se deduce que las interacciones entre las moléculas presentes en la atmósfera y la superficie de la muestra modifican la superficie. Esta alteración superficial se traduce en un cambio significativo en las propiedades de emisión. Este comportamiento se atribuye a la posible adsorción de moléculas sobre la superficie pasivando los centros no radiativos, y como consecuencia, mejorando las propiedades ópticas. Además, los resultados demuestran que las moléculas que contienen oxígeno con mayor polaridad y más ligeras son adsorbidas con mayor facilidad, lo que hace que la intensidad óptica sufra variaciones despreciables con respecto a la emisión en aire. Con el fin de desarrollar sensores, las muestras se procesan y los dispositivos se caracterizan eléctricamente. El procesado consiste en dos contactos cuadrados de una aleación de Ti/Au. Durante el procesado, lo más importante a tener en cuenta es no realizar ningún ataque o limpieza que pueda dañar la superficie y deteriorar las propiedades de las nanostructuras. En este apartado, se realiza un análisis completo de una serie de tres muestras: GaAs (bulk), un pozo cuántico superficial (SQW) de Ino.5Gao.5As y SQDs de Ino.5Gao.5As. Para ello, a cada una de las muestras se le realizan medidas de I-V en distintas condiciones ambientales. En primer lugar, siguiendo los resultados obtenidos ópticamente, se lleva a cabo una comparación de la respuesta eléctrica en vacío y aire. A pesar de que todas las muestras presentan un carácter más resistivo en vacío que en aire, se observa una mayor influencia sobre la muestra de SQD. En vacío, la resistencia de los SQDs decrece un 99% respecto de su valor en aire, mientras que la variación de la muestras de GaAs e Ino.5Gao.5As SQW muestran una reducción, respectivamente, del 31% y del 20%. En segundo lugar, se realiza una evaluación aproximada del posible efecto de la humedad en la resistencia superficial de las muestras mediante la exhalación humana. Como resultado se obtiene, que tras la exhalación, la resistencia disminuye bruscamente y recupera su valor inicial cuando dicho proceso concluye. Este resultado preliminar indica que la humedad es un factor crítico en las propiedades eléctricas de los puntos cuánticos superficiales. Para la determinación del papel de la humedad en la respuesta eléctrica, se somete a las muestras de SQD y SQW a ambientes con humedad relativa (RH, de la siglas del inglés) controlada y se analiza el efecto sobre la conductividad superficial. Tras la variación de la RH desde 0% hasta el 70%, se observa que la muestra SQW no cambia su comportamiento eléctrico al variar la humedad del ambiente. Sin embargo, la respuesta de la muestra SQD define dos regiones bien diferenciadas, una de alta sensibilidad para valores por debajo del 50% de RH, en la que la resistencia disminuye hasta en un orden de magnitud y otra, de baja sensibilidad (>50%), donde el cambio de la resistencia es menor. Este resultado resalta la especial relevancia no sólo de la composición sino también de la morfología de la nanostructura superficial en el carácter sensitivo de la muestra. Por último, se analiza la influencia de la iluminación en la sensibilidad de la muestra. Nuevamente, se somete a las muestras SQD y SQW a una irradiación de luz de distinta energía y potencia a la vez que se varía controladamente la humedad ambiental. Una vez más, se observa que la muestra SQW no presenta ninguna variación apreciable con las alteraciones del entorno. Su resistencia superficial permanece prácticamente inalterable tanto al modificar la potencia de la luz incidente como al variar la energía de la irradiación. Por el contrario, en la muestra de SQD se obtiene una reducción la resistencia superficial de un orden de magnitud al pasar de condiciones de oscuridad a iluminación. Con respecto a la potencia y energía de la luz incidente, se observa que a pesar de que la muestra no experimenta variaciones notables con la potencia de la irradiación, esta sufre cambios significativos con la energía de la luz incidente. Cuando se ilumina con energías por encima de la energía de la banda prohibida (gap) del GaAs (Eg ~1.42 eV ) se produce una reducción de la resistencia de un orden de magnitud en atmósferas húmedas, mientras que en atmósferas secas la conductividad superficial permanece prácticamente constante. Sin embargo, al inicidir con luz de energía menor que Eg, el efecto que se produce en la respuesta eléctrica es despreciable. Esto se atribuye principalmente a la densidad de portadores fotoactivados durante la irradiación. El volumen de portadores excita dos depende de la energía de la luz incidente. De este modo, cuando la luz que incide tiene energía menor que el gap, el volumen de portadores generados es pequeño y no contribuye a la conductividad superficial. Por el contrario, cuando la energía de la luz incidente es alta (Eg), el volumen de portadores activados es elevado y éstos contribuyen significantemente a la conductividad superficial. La combinación de ambos agentes, luz y humedad, favorece el proceso de adsorción de moléculas y, por tanto, contribuye a la reducción de la densidad de estados superficiales, dando lugar a una modificación de la estructura electrónica y consecuentemente favoreciendo o dificultando el transporte de portadores. ABSTRACT Uncapped three-dimensional (3D) nanostructures have been generally grown to assess their structural quality. However, the tremendous growing importance of the impact of the environment on life has become such nanosystems in very promising candidates for the development of sensing devices. Their direct exposure to changes in the local surrounding may influence their physical properties being a perfect sign of the atmosphere quality. The goal of this thesis is the research of Ino.5Gao.5As surface quantum dots (SQDs) on GaAs(001), covering from their growth to device fabrication, for sensing applications. The achievement of this goal relies on the design, growth and sample characterization, along with device fabrication and characterization. The first issue of the thesis is devoted to analyze the main growth parameters affecting the physical properties of the Ino.5Gao.5As SQDs. It is well known that the growing conditions (growth temperature , deposition rate, V/III flux ratio and treatment after active layer growth) directly affect the physical properties of the epilayer. In this part, taking advantage of the previous results in the group regarding Ino.5Gao.5As QD growth temperature and V/III ratio, the effect of the growth rate and the temperature treatment after QDs growth nucleation is evaluated. Setting the QDs growth temperature at 430°C and the V/III flux ratio to ~20, it is found that the most appropriate conditions rely on growing the QDs at 0.07ML/s and just after QD nucleation, rapidly dropping and again raising 100°C the substrate temperature with respect to the temperature of QD growth. The combination of growing at a fast enough growth rate to promote molecule migration but sufficiently slow to allow QD nucleation, together with the sharp variation of the temperature preserving their shape and composition yield to high density, homogeneous Ino.5Gao.5As SQDs. Besides, it is also demonstrated that this high quality SQDs show excellent optical properties even at room temperature (RT). One of the characteristics by which In0.5Ga0.5As/GaAs SQDs are considered promising candidates for sensing applications is the crucial role that surface plays when interacting with the gases constituting the atmosphere. Therefore, in an attempt to develop sensing devices, the influence of the environment on the physical properties of the samples is evaluated. By comparing the resulting photoluminescence (PL) of SQDs with buried QDs (BQDs), it is found that BQDs do not exhibit any significant variation when changing the environmental conditions whereas, the external conditions greatly act on the SQDs optical properties. On one hand, it is evidenced that PL intensity of SQDs sharply quenches under vacuum and clearly decreases under dry-pure gases atmospheres (N2, O2). On the other hand, it is shown that, in water containing atmospheres, the SQDs PL intensity is maintained with respect to that in air. Moreover, it is found that neither the full width at half maximun nor the emission wavelength manifest any noticeable change indicating that the QDs are not structurally altered by the external atmosphere. These results decisively point to the processes taking place at the surface such as coupling between confined and surface states, to be responsible of this extraordinary behavior. A further analysis of the impact of the atmosphere composition on the optical characteristics is conducted. A sample containing one uncapped In0.5Ga0.5As QDs layer is exposed to different environments. Several solvents presenting different polarity, atomic composition and molecular mass, are used to change the atmosphere composition. It is revealed that low polarity and heavy molecules cause a greater variation on the PL intensity. Besides, oxygen is demonstrated to play a decisive role on the PL response. Results indicate that in presence of oxygen-containing molecules, the PL intensity experiments a less reduction than that suffered in presence of nonoxygen-containing molecules, 90% compared to 77% signal respect to the emission in air. In agreement with these results, it is demonstrated that high polarity and lighter molecules containing oxygen are more easily adsorbed, and consequently, PL intensity is less affected. The presence of defects, unsaturated bonds and in general localized states in the surface are proposed to act as nonradiative recombination centers deteriorating the PL emission of the sample. Therefore, suppression or reduction of the density of such states may lead to an increase or, at least, conservation of the PL signal. This research denotes that the interaction between sample surface and molecules in the atmosphere modifies the surface characteristics altering thus the optical properties. This is attributed to the likely adsoption of some molecules onto the surface passivating the nonradiative recombination centers, and consequently, not deteriorating the PL emission. Aiming for sensors development, samples are processed and electrically characterized under different external conditions. Samples are processed with two square (Ti/Au) contacts. During the processing, especial attention must be paid to the surface treatment. Any process that may damage the surface such as plasma etching or annealing must be avoided to preserve the features of the surface nanostructures. A set of three samples: a GaAs (bulk), In0.5Ga0.5As SQDs and In0.5Ga0.5As surface quantum well (SQW) are subjected to a throughout evaluation. I-V characteristics are measured following the results from the optical characterization. Firstly, the three samples are exposed to vacuum and air. Despite the three samples exhibit a more resistive character in vacuum than in air, it is revealed a much more clear influence of the pressure atmosphere in the SQDs sample. The sheet resistance (Rsh) of SQDs decreases a 99% from its response value under vacuum to its value in air, whereas Rsh of GaAs and In0.5Ga0.5As SQW reduces its value a 31% and a 20%, respectively. Secondly, a rough analysis of the effect of the human breath on the electrical response evidences the enormous influence of moisture (human breath is composed by several components but the one that overwhelms all the rest is the high concentration of water vapor) on the I-V characteristics. Following this result, In0.5Ga0.5As SQDs and In0.5Ga0.5As SQW are subjected to different controlled relative humidity (RH) environments (from 0% to 70%) and electrically characterized. It is found that SQW shows a nearly negligible Rsh variation when increasing the RH in the surroundings. However, the response of SQDs to changes in the RH defines two regions. Below 50%, high sensitive zone, Rsh of SQD decreases by more than one order of magnitude, while above 50% the dependence of Rsh on the RH becomes weaker. These results remark the role of the surface and denote the existence of a finite number of surface states. Nevertheless, most significantly, they highlight the importance not only of the material but also of the morphology. Finally, the impact of the illumination is determined by means of irradiating the In0.5Ga0.5As SQDs and In0.5Ga0.5As SQW samples with different energy and power sources. Once again, SQW does not exhibit any correlation between the surface conductivity and the external conditions. Rsh remains nearly unalterable independently of the energy and power of the incident light. Conversely, Rsh of SQD experiences a decay of one order of magnitude from dark-to-photo conditions. This is attributed to the less density of surface states of SQW compared to that of SQDs. Additionally, a different response of Rsh of SQD with the energy of the impinging light is found. Illuminating with high energy light results in a Rsh reduction of one order of mag nitude under humid atmospheres, whereas it remains nearly unchanged under dry environments. On the contrary, light with energy below the bulk energy bandgap (Eg), shows a negligible effect on the electrical properties regardless the local moisture. This is related to the density of photocarriers generated while lighting up. Illuminating with excitation energy below Eg affects a small absorption volume and thus, a low density of photocarriers may be activated leading to an insignificant contribution to the conductivity. Nonetheless, irradiating with energy above the Eg can excite a high density of photocarriers and greatly improve the surface conductivity. These results demonstrate that both illumination and humidity are therefore needed for sensing. The combination of these two agents improves the surface passivation by means of molecule adsorption reducing the density of surface states, thus modifying the electronic structures, and consequently, promoting the carrier motion.

Advances on MBE selective area growth of III-nitride nanostructures: from nanoLEDs to pseudo substrates

The aim of this work is to provide an overview on the recent advances in the selective area growth (SAG) of (In)GaN nanostructures by plasma assisted molecular beam epitaxy, focusing on their potential as building blocks for next generation LEDs. The first three sections deal with the basic growth mechanisms of GaN SAG and the emission control in the entire ultraviolet to infrared range, including approaches for white light emission, using InGaN disks and thick segments on axial nanocolumns. SAG of axial nanostructures is eveloped on both GaN/sapphire templates and GaN-buffered Si(111). As an alternative to axial nanocolumns, section 4 reports on the growth and characterization of InGaN/GaN core-shell structures on an ordered array of top-down patterned GaN microrods. Finally, section 5 reports on the SAG of GaN, with and without InGaN insertion, on semi-polar (11-22) and non-polar (11-20) templates. Upon SAG the high defect density present in the templates is strongly reduced as indicated by a dramatic improvement of the optical properties. In the case of SAG on nonpolar (11-22) templates, the formation of nanostructures with a low aspect ratio took place allowing for the fabrication of high-quality, non-polar GaN pseudo-templates by coalescence of these nanostructures.

Molecular recognition with nanostructures fabricated by photopolymerization within metallic subwavelength apertures

The first demonstration of fabrication of submicron lateral resolution molecularly imprinted polymer (MIP) patterns by photoinduced local polymerization within metal subwavelength apertures is reported. The size of the photopolymerized MIP features is finely tuned by the dose of 532 nm radiation. Rhodamine 123 (R123) has been selected as a fluorescent model template to prove the recognition capability of the MIP nanostructures, which has been evaluated by fluorescence lifetime imaging microscopy (FLIM) with single photon timing measurements. The binding selectivity provided by the imprinting effect has been confirmed in the presence of compounds structurally related to R123. These results pave the way to the development of nanomaterial architectures with biomimetic artificial recognition properties for environmental, clinical and food testing.

Effective nonlinear model of resonant tunneling nanostructures

We introduce a model of a nonlinear double-barrier structure to describe in a simple way the effects of electron-electron scattering while remaining analytically tractable. The model is based on a generalized effective-mass equation where a nonlinear local field interaction is introduced to account for those inelastic scattering phenomena. Resonance peaks seen in the transmission coefficient spectra for the linear case appear shifted to higher energies depending on the magnitude of the nonlinear coupling. Our results are in good agreement with self-consistent solutions of the Schrodinger and Poisson equations. The calculation procedure is seen to be very fast, which makes our technique a good candidate for a rapid approximate analysis of these structures.

CO2 adsorption on crystalline graphitic nanostructures

CO2 adsorption has been measured in different types of graphitic nanostructures (MWCNTs, acid treated MWCNTs, graphene nanoribbons and pure graphene) in order to evaluate the effect of the different defective regions/conformations in the adsorption process, i.e., sp3 hybridized carbon, curved regions, edge defects, etc. This analysis has been performed both in pure carbon and nitrogen-doped nanostructures in order to monitor the effect of surface functional groups on surface created after using different treatments (i.e., acid treatment and thermal expansion of the MWCNTs), and study their adsorption properties. Interestingly, the presence of exposed defective regions in the acid treated nanostructures (e.g., uncapped nanotubes) gives rise to an improvement in the amount of CO2 adsorbed; the adsorption process being completely reversible. For N-doped nanostructures, the adsorption capacity is further enhanced when compared to the pure carbon nanotubes after the tubes were unzipped. The larger proportion of defect sites and curved regions together with the presence of stronger adsorbent–adsorbate interactions, through the nitrogen surface groups, explains their larger adsorption capacity.

Effects of Ultrasound Irradiation on the Synthesis of Metal Oxide Nanostructures

High intensity ultrasound can be used for the production of novel nanomaterials, including metal oxides. According to previous works in this field, the most notable effects are consequence of acoustic cavitation. In this context, we have studied the preparation of different materials in the presence of ultrasound, including N-doped TiO2 nanopowder, NiTiO3 nanorods and MnOx thin films. Ultrasound did not show a significant effect in all the cases. Exclusively for NiTiO3 nanorods a reduction of the final particle size occurs upon ultrasonic irradiation. From these results, it can be concluded that the ultrasound irradiation does not always play a key role during the synthesis of metal oxides. The effects seem to be particularly relevant in those cases where mass transport is highly hindered and in those procedures that require the rupture of nanoparticle aggregates to obtain a homogenous dispersion.

Nanostructures, Semicrytalline Morphology, and Nanoscale Confinement Effect on the Crystallization Kinetics in Self-Organized Block Copolymer/Thermoset Blends

This work reports the first instance of self-organized thermoset blends containing diblock copolymers with a crystallizable thermoset-immiscible block. Nanostructured thermoset blends of bisphenol A-type epoxy resin (ER) and a low-molecular-weight (M-n = 1400) amphiphilic polyethylene-block-poly(ethylene oxide) (EEO) symmetric diblock copolymer were prepared using 4,4'-methylenedianiline (MDA) as curing agent and were characterized by transmission electron microscopy (TEM), atomic force microscopy (AFM), small-angle X-ray scattering (SAXS), and differential scanning calorimetry (DSC). All the MDA-cured ER/EEO blends do not show macroscopic phase separation but exhibit microstructures. The ER selectively mixes with the epoxy-miscible PEO block in the EEO diblock copolymer whereas the crystallizable PE blocks that are immiscible with ER form separate microdomains at nanoscales in the blends. The PE crystals with size on nanoscales are formed and restricted within the individual spherical micelles in the nanostructured ER/EEO blends with EEO content up to 30 wt %. The spherical micelles are highly aggregated in the blends containing 40 and 50 wt % EEO. The PE dentritic crystallites exist in the blend containing 50 wt % EEO whereas the blends with even higher EEO content are completely volume-filled with PE spherulites. The semicrystalline microphase-separated lamellae in the symmetric EEO diblock copolymer are swollen in the blend with decreasing EEO content, followed by a structural transition to aggregated spherical micellar phase morphology and, eventually, spherical micellar phase morphology at the lowest EEO contents. Three morphological regimes are identified, corresponding precisely to the three regimes of crystallization kinetics of the PE blocks. The nanoscale confinement effect on the crystallization kinetics in nanostructured thermoset blends is revealed for the first time. This new phenomenon is explained on the basis of homogeneous nucleation controlled crystallization within nanoscale confined environments in the block copolymer/thermoset blends.

Phase behavior, crystallization, and nanostructures in thermoset blends of epoxy resin and amphiphilic star-shaped block copolymers

This article reports thermoset blends of bisphenol A-type epoxy resin (ER) and two amphiphilic four-arm star-shaped diblock copolymers based on hydrophilic poly(ethylene oxide) (PEO) and hydrophobic poly(propylene oxide) (PPO). 4,4'-Methylenedianiline (MDA) was used as a curing agent. The first star-shaped diblock copolymer with 70 wt% ethylene oxide (EO), denoted as (PPO-PEO)(4), consists of four PPO-PEO diblock arms with PPO blocks attached on an ethylenediamine core; the second one with 40 wt% EO, denoted as (PEO-PPO)(4), contains four PEO-PPO diblock arms with PEO blocks attached on an ethylenediamine core. The phase behavior, crystallization, and nanoscale structures were investigated by differential scanning calorimetry, transmission electron microscopy, and small-angle X-ray scattering. It was found that the MDA-cured ER/(PPO-PEO)(4) blends are not macroscopically phase-separated over the entire blend composition range. There exist, however, two microphases in the ER/(PPO-PEO)(4) blends. The PPO blocks form a separated microphase, whereas the ER and the PEO blocks, which are miscible, form another microphase. The ER/(PPO-PEO)(4) blends show composition-dependent nanostructures on the order of 10-30 nm. The 80/20 ER/(PPO-PEO)(4) blend displays spherical PPO micelles uniformly dispersed in a continuous ER-rich matrix. The 60/40 ER/(PPO-PEO)(4) blend displays a combined morphology of worm-like micelles and spherical micelles with characteristic of a bicontinuous microphase structure. Macroscopic phase separation took place in the MDA-cured ER/(PEO-PPO)(4) blends. The MDA-cured ER/(PEO-PPO)(4) blends with (PEO-PPO)(4) content up to 50 wt% exhibit phase-separated structures on the order of 0.5-1 mu m. This can be considered to be due to the different EO content and block sequence of the (PEO-PPO)(4) copolymer. (c) 2006 Wiley Periodicals, Inc.