Controlled synthesis of poly(neopentyl p-styrene sulfonate) via reversible addition-fragmentation chain transfer polymerisation

The controlled synthesis of poly(neopentyl p-styrene sulfonate) (PNSS) using RAFT polymerisation has been studied. Selected experimental conditions led to the production of PNSS with variable molecular weights and low dispersities (D{stroke}≤1.50). The controlled synthesis of poly(neopentyl p-styrene sulfonate) (PNSS) using reversible addition-fragmentation chain transfer polymerisation has been studied under a wide range of experimental conditions. PNSS can be used as an organic-soluble, thermally labile precursor for industrially valuable poly(p-styrene sulfonate), widely employed in technologies such as ionic exchange membranes and organic electronics. The suitability of two different chain transfer agents, three solvents, three different monomer concentrations and two different temperatures for the polymerisation of neopentyl p-styrene sulfonate is discussed in terms of the kinetics of the process and characteristics of the final polymer. Production of PNSS with systematically variable molecular weights and low dispersities (D{stroke} ≤1.50 in all cases) has been achieved using 2-azidoethyl 2-(dodecylthiocarbonothioylthio)-2-methylpropionate in anisole at 75°C, with an initial monomer concentration of 4.0molL-1. Finally, a poly(neopentyl p-styrene sulfonate)-b-polybutadiene-b-poly(neopentyl p-styrene sulfonate) (PNSS-b-PBD-b-PNSS) triblock copolymer has been synthesised via azide-alkyne click chemistry. Moreover, subsequent thermolysis of the PNSS moieties generated poly(p-styrene sulfonate) end blocks. This strategy allows the fabrication of amphiphilic copolymer films from single organic solvents without the need for post-deposition chemical treatment.

Composition of a protein-like fluorophore of dissolved organic matter in coastal wetland and estuarine ecosystems

This study demonstrates the compositional heterogeneity of a protein-like fluorescence emission signal (T-peak; excitation/emission maximum at 280/325 nm) of dissolved organic matter (DOM) samples collected from subtropical river and estuarine environments. Natural water samples were collected from the Florida Coastal Everglades ecosystem. The samples were ultrafiltered and excitation–emission fluorescence matrices were obtained. The T-peak intensity correlated positively with N concentration of the ultrafiltered DOM solution (UDON), although, the low correlation coefficient (r2=0.140, p<0.05) suggested the coexistence of proteins with other classes of compounds in the T-peak. As such, the T-peak was unbundled on size exclusion chromatography. The elution curves showed that the T-peak was composed of two compounds with distinct molecular weights (MW) with nominal MWs of about >5×104 (T1) and ∼7.6×103 (T2) and with varying relative abundance among samples. The T1-peak intensity correlated strongly with [UDON] (r2=0.516, p<0.001), while T2-peak did not, which suggested that the T-peak is composed of a mixture of compounds with different chemical structures and ecological roles, namely proteinaceous materials and presumably phenolic moieties in humic-like substances. Natural source of the latter may include polyphenols leached from senescent plant materials, which are important precursors of humic substances. This idea is supported by the fact that polyphenols, such as gallic acid, an important constituent of hydrolysable tannins, and condensed tannins extracted from red mangrove (Rhizophora mangle) leaves exhibited the fluorescence peak in the close vicinity of the T-peak (260/346 and 275/313 nm, respectively). Based on this study the application of the T-peak as a proxy for [DON] in natural waters may have limitations in coastal zones with significant terrestrial DOM input.

Dextranas e seus derivados fosforilados: obtenção e avaliação do potencial antioxidante, imunomodulatório e anticoagulante

Glucans are polysaccharides with different pharmacological and biological activities described. However, there are some reports about the activities of the glucan type α (alpha). In this context, a group of α-D-glucans called dextrans extracted from Leuconostoc mesenteroides bacteria, with molecular weights of 10 (D10), 40 (D40) and 147 (D147) kDa and their phosphorylated derivatives P10, P40 and P147, were evaluated as for their antioxidant, anticoagulant and immunomodulatory potential for the first time, in order to elucidate compounds with potent activities and low toxicity. Infrared spectroscopy analysis, monosaccharide composition and chemical dosages showed that these dextrans are the same polysaccharide, but with different molecular weights, besides confirming the success of phosphorylation. None presented with anticoagulant features. The reducing power test showed that D147 was twice as potent as other dextrans. On the other hand, all six samples showed similar activity (50%) when it came to scavenging the OH radical. To the superoxide ion scavenging, only D10 had a pronounced activity (50%). D40 was the single native dextran that presented with immunomodulatory features since it double stimulated the proliferation of murine macrophages (RAW 264.7) and double the release of nitric oxide by the cells, both in the absence and presence of lipopolysaccharides (LPS). In addition, D40 showed a greater scavenging activity (50%) for the hydrogen peroxide, which caused it to also be the more potent dextran when it came to inhibiting lipid peroxidation (70%). On other hand, P147 showed the highest iron and copper ion chelation activity (~85%). P10 proved be the most effective compound to macrophage proliferation. The results point toward dextrans with a 40 kDa weight as being ideal for antioxidant and immunomodulatory use, could be supplemented with phosphorylated derivatives. However, future studies with the D40 and other similarly dextrans are to confirm this hypothesis.

Formation of sub-7 nm feature size PS-b-P4VP block copolymer structures by solvent vapour process

The nanometer range structure produced by thin films of diblock copolymers makes them a great of interest as templates for the microelectronics industry. We investigated the effect of annealing solvents and/or mixture of the solvents in case of symmetric Poly (styrene-block-4vinylpyridine) (PS-b-P4VP) diblock copolymer to get the desired line patterns. In this paper, we used different molecular weights PS-b-P4VP to demonstrate the scalability of such high χ BCP system which requires precise fine-tuning of interfacial energies achieved by surface treatment and that improves the wetting property, ordering, and minimizes defect densities. Bare Silicon Substrates were also modified with polystyrene brush and ethylene glycol self-assembled monolayer in a simple quick reproducible way. Also, a novel and simple in situ hard mask technique was used to generate sub-7nm Iron oxide nanowires with a high aspect ratio on Silicon substrate, which can be used to develop silicon nanowires post pattern transfer.

Fabrication of sub-10 nm lamellar structures by solvent vapour annealing of block copolymers

Fabrication of nanoscale patterns through the bottom-up approach of self-assembly of phase-separated block copolymers (BCP) holds promise for nanoelectronics applications. For lithographic applications, it is useful to vary the morphology of BCPs by monitoring various parameters to make “from lab to fab” a reality. Here I report on the solvent annealing studies of lamellae forming polystyrene-blockpoly( 4-vinylpyridine) (PS-b-P4VP). The high Flory-Huggins parameter (χ = 0.34) of PS-b-P4VP makes it an ideal BCP system for self-assembly and template fabrication in comparison to other BCPs. Different molecular weights of symmetric PS-b-P4VP BCPs forming lamellae patterns were used to produce nanostructured thin films by spin-coating from mixture of toluene and tetrahydrofuran(THF). In particular, the morphology change from micellar structures to well-defined microphase separated arrangements is observed. Solvent annealing provides a better alternative to thermal treatment which often requires long annealing periods. The choice of solvent (single and dual solvent exposure) and the solvent annealing conditions have significant effects on the morphology of films and it was found that a block neutral solvent was required to realize vertically aligned PS and P4VP lamellae. Here, we have followed the formation of microdomain structures with time development at different temperatures by atomic force microscopy (AFM). The highly mobilized chains phase separate quickly due to high Flory-Huggins (χ) parameter. Ultra-small feature size (~10 nm pitch size) nanopatterns were fabricated by using low molecular weight PSb- P4VP (PS and P4VP blocks of 3.3 and 3.1 kg mol-1 respectively). However, due to the low etch contrast between the blocks, pattern transfer of the BCP mask is very challenging. To overcome the etch contrast problem, a novel and simple in-situ hard mask technology is used to fabricate the high aspect ratio silicon nanowires. The lamellar structures formed after self-assembly of phase separated PS-b-P4VP BCPs were used to fabricate iron oxide nanowires which acted as hard mask material to facilitate the pattern transfer into silicon and forming silicon nanostructures. The semiconductor and optical industries have shown significant interest in two dimensional (2D) molybdenum disulphide (MoS2) as a potential device material due to its low band gap and high mobility. However, current methods for its synthesis are not ‘fab’ friendly and require harsh environments and processes. Here, I also report a novel method to prepare MoS2 layered structures via self-assembly of a PS-b-P4VP block copolymer system. The formation of the layered MoS2 was confirmed by XPS, Raman spectroscopy and high resolution transmission electron microscopy.

Dispositifs optoélectroniques à base de semi-conducteurs organiques en couches minces

Les petites molécules de type p à bandes interdites étroites sont de plus en plus perçues comme des remplaçantes possibles aux polymères semi-conducteurs actuellement utilisés conjointement avec des dérivés de fullerènes de type n, dans les cellules photovoltaïques organiques (OPV). Par contre, ces petites molécules tendent à cristalliser facilement lors de leur application en couches minces et forment difficilement des films homogènes appropriés. Des dispositifs OPV de type hétérojonction de masse ont été réalisés en ajoutant différentes espèces de polymères semi-conducteurs ou isolants, agissant comme matrices permettant de rectifier les inhomogénéités des films actifs et d’augmenter les performances des cellules photovoltaïques. Des polymères aux masses molaires spécifiques ont été synthétisés par réaction de Wittig en contrôlant précisément les ratios molaires des monomères et de la base utilisée. L’effet de la variation des masses molaires en fonction des morphologies de films minces obtenus et des performances des diodes organiques électroluminescentes reliées, a également été étudié. La microscopie électronique en transmission (MET) ou à balayage (MEB) a été employée en complément de la microscopie à force atomique (AFM) pour suivre l’évolution de la morphologie des films organiques minces. Une nouvelle méthode rapide de préparation des films pour l’imagerie MET sur substrats de silicium est également présentée et comparée à d’autres méthodes d’extraction. Motivé par le prix élevé et la rareté des métaux utilisés dans les substrats d’oxyde d’indium dopé à l’étain (ITO), le développement d’une nouvelle méthode de recyclage eco-responsable des substrats utilisés dans ces études est également présenté.

Avaliação da hidrólise alcalina da quitina e elaboração de filmes de quitosana para aplicação na adsorção do corante têxtil reativo preto 5

Nesta pesquisa, diferentes amostras de quitosana foram produzidas por diferentes condições de hidrólise alcalina da quitina. A partir das amostras de quitosana foram produzidos filmes,sendo estes aplicados na adsorção do corante têxtil reativo preto 5 e os resultados foram comparados com os dos seus respectivos pós. Os valores das massas molares da quitosana aumentaram em função do aumento do diâmetro da quitina e diminuíram com o aumento da relação de solução NaOH:quitina, da concentração de NaOH e tempo de reação, e ficaram na faixa de 100 a 200 kDa. Um comportamento inverso foi observado para o grau de desacetilação da quitosana, e seus valores variaram de 65 a 95%. Quanto aos filmes biopoliméricos elaborados, os que apresentaram melhores valores quanto as suas propriedades mecânicas e de permeabilidade ao vapor de água foram os filmes produzidos com quitosana de mais elevada massa molar e menor grau de desacetilação. A fim de avaliar o comportamento dos filmes em processos de adsorção, estes foram aplicados na remoção do corante reativo preto 5 (RB5) em diferentes condições de pH (4, 6 e 8). Após, foram escolhidos quatro filmes de quitosana (FQ), com diferentes graus de desacetilação e massas molares, que foram comparados com as quitosanas na forma de pó (PQ) no estudo de adsorção. Este foi realizado sob diversas condições experimentais (pH, temperatura e taxa de agitação) através das isotermas de equilíbrio, da termodinâmica e da cinética. Análises de interação e ciclos de adsorção-dessorção também foram realizados. Verificou-se que PQ e FQ com grau de desacetilação de 95% e massa molar de 100 kDa foram os adsorvente mais adequados, apresentando mais de 99% de remoção do corante RB5 em pH 4,0. Para ambos, PQ e FQ, o modelo de Langmuir foi o mais adequado para representar os dados de equilíbrio. As capacidades máximas de adsorção foram 654,3 e 589,5 mg g-1 para PQ e FQ, respectivamente, obtidos a 298 K. O processo de adsorção foi espontâneo, favorável e exotérmico. A adsorção de RB5 para PQ e FQ seguiu o modelo cinético de Elovich,e ocorreram interações eletrostáticas do PQ-RB5 e do FQ-RB5. Os filmes de quitosana foram reutilizados três vezes, enquanto que a quitosana em pó não pode ser reutilizada.

Extraction and purification of immunoglobulin G with aqueous biphasic systems

The immune system is able to produce antibodies, which have the capacity to recognize and to bind to foreign molecules or pathogenic organisms. Currently, there are a diversity of diseases that can be treated with antibodies, like immunoglobulins G (IgG). Thereby, the development of cost-efficient processes for their extraction and purification is an area of main interest in biotechnology. Aqueous biphasic systems (ABS) have been investigated for this purpose, once they allow the reduction of costs and the number of steps involved in the process, when compared with conventional methods. Nevertheless, typical ABS have not showed to be selective, resulting in low purification factors and yields. In this context, the addition of ionic liquids (ILs) as adjuvants can be a viable and potential alternative to tailor the selectivity of these systems. In this work, ABS composed of polyethylene glycol (PEG) of different molecular weight, and a biodegradable salt (potassium citrate) using ILs as adjuvants (5 wt%), were studied for the extraction and purification of IgG from a rabbit source. Initially, it was tested the extraction time, the effect on the molecular weight of PEG in a buffer solution of K3C6H5O7/C6H8O7 at pH≈7, and the effect of pH (59) on the yield (YIgG) and extraction efficiency (EEIgG%) of IgG. The best results regarding EEIgG% were achieved with a centrifugation step at 1000 rpm, during 10 min, in order to promote the separation of phases followed by 120 min of equilibrium. This procedure was then applied to the remaining experiments. The results obtained in the study of PEGs with different molecular weights, revealed a high affinity of IgG for the PEG-rich phase, and particularly for PEGs of lower molecular weight (EEIgG% of 96 % with PEG 400). On the other hand, the variation of pH in the buffer solution did not show a significant effect on the EEIgG%. Finally, it was evaluated the influence of the addition of different ILs (5% wt) on the IgG extraction in ABS composed of PEG 400 at pH≈7. In these studies, it was possible to obtain EEIgG% of 100% with the ILs composed of the anions [TOS]-, [CH3CO2]-and Cl-, although the obtained YIgG% were lower than 40%. On the other hand, the ILs composed of the anions Br-, as well as of the cation [C10mim]+, although not leading to EEIgG% of 100%, provide an increase in the YIgG%. ABS composed of PEG, a biodegradable organic salt and ILs as adjuvants, revealed to be an alternative and promising method to purify IgG. However, additional studies are still required in order to reduce the loss of IgG.

Anti-Metastatic Properties of a Marine Bacterial Exopolysaccharide-Based Derivative Designed to Mimic Glycosaminoglycans

Osteosarcoma is the most frequent malignant primary bone tumor characterized by a high potency to form lung metastases. In this study, the effect of three oversulfated low molecular weight marine bacterial exopolysaccharides (OS-EPS) with different molecular weights (4, 8 and 15 kDa) were first evaluated in vitro on human and murine osteosarcoma cell lines. Different biological activities were studied: cell proliferation, cell adhesion and migration, matrix metalloproteinase expression. This in vitro study showed that only the OS-EPS 15 kDa derivative could inhibit the invasiveness of osteosarcoma cells with an inhibition rate close to 90%. Moreover, this derivative was potent to inhibit both migration and invasiveness of osteosarcoma cell lines; had no significant effect on their cell cycle; and increased slightly the expression of MMP-9, and more highly the expression of its physiological specific tissue inhibitor TIMP-1. Then, the in vivo experiments showed that the OS-EPS 15 kDa derivative had no effect on the primary osteosarcoma tumor induced by osteosarcoma cell lines but was very efficient to inhibit the establishment of lung metastases in vivo. These results can help to better understand the mechanisms of GAGs and GAG-like derivatives in the biology of the tumor cells and their interactions with the bone environment to develop new therapeutic strategies.

Aplicação de peroxidase para degradação de deoxinivalenol

Deoxinivalenol (DON), uma das principais micotoxinas encontradas em matrizes alimentares, é um composto químico que possui em sua estrutura um anel epóxido que lhe confere alto grau de toxicidade. A aplicação de enzimas em processos de degradação de DON vem se destacando, pela estabilidade durante o processo reacional e baixo custo de produção. O objetivo desse trabalho foi estudar o potencial de peroxidase proveniente de farelo de arroz (FA) e farelo de soja (FS) para degradar DON. As condições de obtenção da PO a partir de FA foram definidas por planejamento experimental DCCR 23 , sendo extraída de 5 g de farelo com 50 mL de tampão fosfato 0,04 mol L-1 pH 5, agitados orbitalmente durante 60 min a 100 rpm, e para a PO obtida de FS as condições diferenciaram somente quanto a solução extratora, tampão fosfato 0,01 mol L-1 pH 4,7. A técnica que apresentou melhores índices de purificação para a enzima foi a partição trifásica apresentando fator de purificação e recuperação de 5,6 e 50 % para a obtida de FA e 13,61 e 50 % para FS. A PO de FA apresentou maior atividade em tampão fosfato 5 mmol L-1 pH 5,5 para as formas bruta e pura, diferindo na temperatura de reação de 25 °C e 10 °C, KM de 0,15 e 0,06 mmol L-1 e Vmáx de 769 e 667 U mg-1 , respectivamente. A PO de FS as condições foram: tampão fosfato 5 mmol L-1 pH 5, reação a 35 e 30 °C durante 10 e 5 min, KM de 0,17 e 0,05 mmol L-1 e Vmáx de 196 e 182 U mg-1 , respectivamente. A PO de FA demonstrou maior estabilidade em pH 5 enquanto que a de FS em pH 6, ambas enzimas apresentaram maior estabilidade térmica a 0 °C, as massas moleculares encontradas por eletroforese foram 41 e 34 kDa, respectivamente. Ao final das etapas de obtenção, purificação e caracterização obteve-se uma atividade específica de 116 e 794 U.mg-1 , e 4363 e 17453 U g-1 , respectivamente para PO de FA e FS. A determinação de DON e De-DON foi realizada por HPLC-DAD e LC-ESI-MS/MS para avaliação dos ensaios de degradação. A enzima comercial HRP, mostrou maior potencial de redução sobre DON (55% após 1 h de reação), no entanto em 3 h de reação, a concentração inicial da micotoxina DON foi verificada, o que evidencia que a redução pode ocorrer por adsorção ou por formação de um composto de degradação que apresente a mesma massa molecular. O emprego da enzima PO obtida de FA e FS na degradação necessita de uma avaliação cinética micotoxicologica para definição das condições de redução significativa dos níveis de DON.

Dispositifs optoélectroniques à base de semi-conducteurs organiques en couches minces

Les petites molécules de type p à bandes interdites étroites sont de plus en plus perçues comme des remplaçantes possibles aux polymères semi-conducteurs actuellement utilisés conjointement avec des dérivés de fullerènes de type n, dans les cellules photovoltaïques organiques (OPV). Par contre, ces petites molécules tendent à cristalliser facilement lors de leur application en couches minces et forment difficilement des films homogènes appropriés. Des dispositifs OPV de type hétérojonction de masse ont été réalisés en ajoutant différentes espèces de polymères semi-conducteurs ou isolants, agissant comme matrices permettant de rectifier les inhomogénéités des films actifs et d’augmenter les performances des cellules photovoltaïques. Des polymères aux masses molaires spécifiques ont été synthétisés par réaction de Wittig en contrôlant précisément les ratios molaires des monomères et de la base utilisée. L’effet de la variation des masses molaires en fonction des morphologies de films minces obtenus et des performances des diodes organiques électroluminescentes reliées, a également été étudié. La microscopie électronique en transmission (MET) ou à balayage (MEB) a été employée en complément de la microscopie à force atomique (AFM) pour suivre l’évolution de la morphologie des films organiques minces. Une nouvelle méthode rapide de préparation des films pour l’imagerie MET sur substrats de silicium est également présentée et comparée à d’autres méthodes d’extraction. Motivé par le prix élevé et la rareté des métaux utilisés dans les substrats d’oxyde d’indium dopé à l’étain (ITO), le développement d’une nouvelle méthode de recyclage eco-responsable des substrats utilisés dans ces études est également présenté.

Purificação e caracterização parcial de duas N-acetil-ß-hexosaminidases do Equinoderma marinho Echinometra lucunter

Two b-N-acetylhexosaminidases (F11 e F15) were purified from Echinometra lucunter gonads extracts. The purified enzymes were obtained using ammonium sulfate fractionation, followed by gel filtration chromatographies (Sephacryl S-200, Sephadex G-75 and Sephacryl S-200). The F11 fraction was purified 192.47 -fold with a 28.5% yield, and F15 fraction 85.41 -fold with a 32.3% yield. The molecular weights of the fractions were 116 kDa for F11 and 42 kDa for F15 using SDS-PAGE. In Sephacryl S-200, F15 was 84 kDa, indicating that it is a dimeric protein. When p-nitrophenyl-β-D-glycosaminide was used as substrate, we determined an apparent Km of 0.257 mM and Vmax of 0.704 for F11 and for F15 the Km was 0.235 mM and Vmax of 0.9 mM of product liberated by hour. Both enzymes have optimum pH and temperature respectively at 5.0 and 45 °C. The enzymes showed inhibition by silver nitrate, while the glucuronic acid was a potent activator. The high inhibition of F15 by N-etylmaleimide indicates that sulphydril groups are involved in the catalysis of synthetic substrate

Unravelling the nanostructure of strawberry fruit pectins by atomic force microscopy

Atomic force microscopy (AFM) allows the analysis of individual polymers at nanostructural level with a minimal sample preparation. This technique has been used to analyse the pectin disassembly process during the ripening and postharvest storage of several fleshy fruits. In general, pectins analysed by AFM are usually visualized as isolated chains, unbranched or with a low number of branchs and, occasionally, as large aggregates. However, the exact nature of these structures is unknown. It has been suggested that pectin aggregates represent a mixture of rhamnonogalacturonan I and homogalacturonan, while isolated chains and their branches are mainly composed by polygalacturonic acid. In order to gain insight into the nature of these structures, sodium carbonate soluble pectins from ripe strawberry (Fragaria x ananassa, Duch.) fruits were subjected to enzymatic digestion with endo-Polygalacturonase M2 from Aspergillus aculeatus, and the samples visualized by AFM at different time intervals. Pectins isolated from control, non-transformed plants, and two transgenic genotypes with low level of expression of ripening-induced pectinase genes encoding a polygalacturonase (APG) or a pectate lyase (APEL) were also included in this study. Before digestion, isolated pectin chains from control were shorter than those from transgenic fruits, showing number-average (LN) contour length values of 73.2 nm vs. 95.9 nm and 91.4 nm in APG and APEL, respectively. The percentage of branched polymers was significantly higher in APG polyuronides than in the remaining genotypes, 33% in APG vs. 6% in control and APEL. As a result of the endo-PG treatment, a gradual decrease in the main backbone length of isolated chains was observed in the three samples. The minimum LN value was reached after 8 h of digestion, being similar in the three genotypes, 22 nm. By contrast, the branches were not visible after 1.5-2 h of digestion. LN values were plotted against digestion time and the data fitted to a first-order exponential decay curve, obtaining R2 values higher than 0.9. The half digestion time calculated with these equations were similar for control and APG pectins, 1.7 h, but significantly higher in APEL, 2.5 h, indicating that these polymer chains were more resistant to endo-PG digestion. Regarding the pectin aggregates, their volumes were estimated and used to calculate LN molecular weights. Before digestion, control and APEL samples showed complexes of similar molecular weights, 1722 kDa, and slightly higher than those observed in APG samples. After endo-PG digestion, size of complexes diminished significantly, reaching similar values in the three pectin samples, around 650 kDa. These results suggest that isolated polymer chains visualized by AFM are formed by a HG domain linked to a shorter polymer resistant to endo-PG digestion, maybe xylogalacturonan or RG-I. The silencing of the pectate lyase gene slightly modified the structure and/or chemical composition of polymer chains making these polyuronides more resistant to enzymatic degradation. Similarly, polygalacturonic acid is one of the main component of the aggregates.

Porous self-protonating spiropyran-based NIPAAm gels with improved reswelling kinetics

The final publication is available at Springer via http://dx.doi.org/[10.1007/s10853-015-9458-2]

Renal and vascular effects of the natriuretic peptide isolated from Crotalus durissus cascavella venom

Crotalus durissus cascavella is a snake that is usually found in the scrublands of northeast Brazil. The components of its venom may have effects on the vascular and renal systems. Recently, a new bradykinin inhibitory peptide has been identified in the venom of the Crotalinae family. The aim of the present study was to investigate the renal and vascular effects of the natriuretic peptide isolated from the venom of Crotalus durissus cascavella (NP2_Casca). The chromatographic profile showed the fractionation of substances identified as convulxin, gyroxin, crotoxin and crotamine, as well as fractions V and VI. The electrophoretic profile of fraction V consisted of several bands ranging from approximately 6 kDa to 13 kDa, while fraction VI showed only two main electrophoretic bands with molecular weights of approximately 6 and 14 kDa. Reverse-phase chromatography showed that NP2_Casca corresponds to about 18% of fraction VI and that this fraction is the main natriuretic peptide. NP2_Casca was compared to other natriuretic peptides from other sources of snake venom. All amino acid sequences that were compared showed a consensus region of XGCFGX, XLDRIX and XSGLGCX. The group treated with NP2-Casca showed an increase in perfusion pressure, renal vascular resistance, urinary flow and glomerular filtration rate. The percent of total and proximal tubular transport of sodium was reduced significantly after administration of the peptide. The mean arterial pressure showed a dose-dependent decrease after infusion of NP2_Casca, and an increase in nitrite production. In the aortic ring assay, NP2_Casca caused a relaxant effect in endothelium-intact thoracic aortic rings precontracted with phenylephrine in the presence and absence of isatin. NP2_Casca failed to relax the aortic rings precontracted with an isosmotic potassium Krebs-Henseleit solution. In conclusion, the natriuretic peptide isolated from Crotalus durissus cascavella venom produced renal and vascular effects. NP2_Casca reduced total and proximal sodium tubular transport, leading to an increase in sodium excretion, thereby demonstrating a diuretic action. A hypotensive effect was displayed in an arterial pressure assay, with an increase in nitrite production, suggesting a possible vasoactive action. (C) 2008 Elsevier Ltd. All rights reserved.