Aresta e vértices de corte

A videoaula traz conceitos de aresta e vértices de corte. Destaca também as árvores e suas categorias, tipos específicos de grafo.

Remoção de metais pesados em efluentes sintéticos utilizando vermiculita como adsorvente

Heavy metals are used in many industrial processestheirs discard can harm fel effects to the environment, becoming a serious problem. Many methods used for wastewater treatment have been reported in the literature, but many of them have high cost and low efficiency. The adsorption process has been used as effective for the metal remoal ions. This paper presents studies to evaluate the adsorption capacity of vermiculite as adsorbent for the heavy metals removal in a synthetic solution. The mineral vermiculite was characterized by differents techniques: specific surface area analysis by BET method, X-ray diffraction, raiosX fluorescence, spectroscopy in the infraredd region of, laser particle size analysis and specific gravity. The physical characteristics of the material presented was appropriate for the study of adsorption. The adsorption experiments weredriveal finite bath metod in synthetic solutions of copper, nickel, cadmium, lead and zinc. The results showed that the vermiculite has a high potential for adsorption, removing about 100% of ions and with removal capacity values about 85 ppm of metal in solution, 8.09 mg / g for cadmium, 8.39 mg/g for copper, 8.40 mg/g for lead, 8.26 mg/g for zinc and 8.38 mg/g of nickel. The experimental data fit in the Langmuir and Freundlich models. The kinetic datas showed a good correlation with the pseudo-second order model. It was conducteas a competition study among the metals using vermiculiti a adsorbent. Results showed that the presence of various metals in solution does not influence their removal at low concentrations, removing approximat wasely 100 % of all metals present in solutions

Impregnação de metais em xisto retortado para uso como adsorventes

Concern with the environment has lead to an increase in the research for new adsorption techniques, low cost adsorvent materials and with high availability. Many works search the development of higher selectivity modified adsorvents. The Brazil has the second world reserve of oiled shale, because of it, the use of that reject is of great interest. This study has the goal of characterize and analyze the retorted shale, reject of the pirobetuminous shale pyrolysis, and the retorted shale modified through the humid impregnation method, wich the precursors were the metals nitrates ( Cobalt, Nickel and Copper), to the usage has adsorvent materials. The samples were characterized chemically, textually and structurally by the X ray fluorescence (XRF), BET, X ray diffraction (XRD) and scanning electronic microscopy (SEM) techniques. The impregnated samples showed a reduction in the superficial area and in the pore volume when compared with the retorted shale. Besides that, diffractions referred to the impregnated metals where observed in the XRD analysis, wich were the same metals detected in the XRF and SEM analysis. The materials showed homogeneity in it s composition. The results shows that the materials presents adequate adsorption characteristics

Estudo da molhabilidade de ligas de adição à base de prata sobre insertos cerâmicos para aplicação em brocas perfuração de poços de petróleo

Metal-ceramic interfaces are present in tricone drill bits with hard ceramic inserts for oil well drilling operations. The combination of actions of cutting, crushing and breaking up of rocks results in the degradation of tricone drill bits by wear, total or partial rupture of the drill bit body or the ceramic inserts, thermal shock and corrosion. Also the improper pressfitting of the ceramic inserts on the bit body may cause its total detachment, and promote serious damages to the drill bit. The improvement on the production process of metal-ceramic interfaces can eliminate or minimize some of above-mentioned failures presented in tricone drill bits, optimizing their lifetime and so reducing drilling metric cost. Brazing is a widely established technique to join metal-ceramic materials, and may be an excellent alternative to the common mechanical press fitting process of hard ceramic inserts on the steel bit body for tricone drill bit. Wetting phenomena plays an essential role in the production of metal/ceramic interfaces when a liquid phase is present in the process. In this work, 72Silver-28Copper eutectic based brazing alloys were melted onto zirconia, silicon nitride and tungsten carbide/Co substrates under high vacuum. Contact angle evolution was measured and graphically plotted, and the interfaces produced were analysed by SEM-EDX. The AgCu eutectic alloy did not wet any ceramic substrates, showing high contact angles, and so without chemical interaction between the materials. Better results were found for the systemns containing 3%wt of titanium in the AgCu alloy. The presence os titanium as a solute in the alloy produces wettable cand termodinamically stable compounds, increasing the ceramics wetting beahviour

Nitretação em plasma com gaiola catódica: caracterização e avaliação do desempenho da camada nitretada em facas de corte

Nowadays, in the plastic industry are used mills that accomplish the recycling of residues generated in the production of its components. These mills contain cut sheets that suffer accelerated wear, once they are submitted constantly to the tribologic efforts, decreasing its useful life. To reduce this problem, it s used noble steels or takes place superficial treatments. The ionic nitriding process presents some limitations related to the uniformity of the layer in pieces with complex geometry, committing its application in pieces as knives, head offices, engagements, etc. However, the new technique of nitriding in cathodic cage eliminates some problems, as the restrictions rings, inherent to the conventional ionic nitriding. In present work, was studied the use viabilization of steels less noble, as SAE 1020, SAE 4320 and SAE 4340, nitreded by two different techniques, to substitute the AISI 01 steels, usually used in the cut knifes fabrication, seeking to reduce the costs and at the sane time to increase the useful life of these knifes. The steel most viable was the SAE 4340, nitrided in cathodic cage, because it presented uniformity in thickness and in the hardness of the layer, besides of increased 58% in the average its useful life

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Avaliação de metodologia de preparo de amostra de petróleo por digestão ácida auxiliada por microondas para determinação de metais por ICP-OES

This project describes a methodology optimization that would allow for a more efficient microwave assisted digestion process for petroleum samples. With the possible chance to vary various factors at once to see if any one factor was significant enough in the answers, experimental planning was used. Microwave assisted digestion allows, through the application of potency, an increasing number of collisions between the HNO3 and H2O2 molecules, favoring sample opening for complex matrixes. For this, a 24 factorial experimental planning was used, varying potency, time and the volumes for HNO3 65% and H2O2 30%. To achieve the desired answers, several elements were monitored (C, Cu, Cr, Fe, Ni, Zn and V) through Inductively coupled plasma atomic emission spectroscopy (ICP-OES). With this initial study it was noticed that the HNO3 was not a significant factor for any of the statistical studies for any of the analytes and the other 3 factors and their interactions showed statistical significance. A Box Behnken experimental planning was used taking in consideration 3 factors: H2O2 volume, time (min) and Potency (W), Nitric Acid kept at 4mL for a mass of 0,1g of petroleum. The results were extremely satisfying showing higher efficiency in the digestion process and taking in a responsibility between the answers for each analyte and the carbon monitoring was achieved in the following conditions: 7mL of H2O2, 700 Watts of potency and a reaction time of 7 minutes with 4mL de HNO3 for a mass of 0,1g of petroleum. The optimized digestion process was applied to four different petroleum samples and the analytes determined by ICP-OES

Extração de metais (K, Mg, Ba, Ca, Cr, Mn, Li, Fe) de água produzida utilizando sistema microemulsionado

The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation

Frequência da infecção por Toxoplasma gondii em galinhas caipira e frangos de corte em regiões dos Estados do Rio Grande do Norte e Paraíba

Toxoplasmosis is a zoonosis caused by Toxoplasma gondii, a protozoan that has a cosmopolitan geographic distribution and low host specificity. Usually a benign and selflimiting, infection can manifest itself in a severe systemic becoming overwhelming in fetuses and patients with immunosuppression. Domestic fowl are considered one of the most important hosts in the epidemiology of toxoplasmosis, since they are potential sources of infection for humans, in addition to playing the role of important indicators of environmental contamination by oocysts of T. gondii. We studied the prevalence of infection by the protozoan in chickens of different breeding systems mesoregions from the states of Rio Grande do Norte and Paraiba: broilers from commercial farms (200/PB) and free-range chickens of small farms (322/RN and PB). Were standardized IFAT and ELISA techniques for detecting specific antibodies in blood samples of birds, and commercial kit was used to determine the prevalence by IHAT. There was no seropositive reaction by T. gondii in the samples of broilers tested, indicating that the particularities of intensive management limit the chances of infection for these animals. Among the hens, the frequency of IgG anti-T. gondii diagnosed by the techniques of IHAT, IFAT and ELISA, respectively, were 3.73% (12/322), 37.88% (122/322) and 40.37% (130/322), for both young and adult animals. Amongst the seropositive samples by IFAT, 33 (27.05%) were positive at a dilution of 1:16, in 1:32, 31 (25.41%), in 1:64, 24 (19.67%), 15 (12.29%) in 1:128, and 19 presented titer greater than or equal to 1:256 (15.57%). The evaluation of the presence of anti-T. gondii should be careful, and reagents IHAT provided erratic results in this measure for the specie studied. This suggests the need for own standardization of the kit before the use in epidemiological studies in animal species. On the other hand, substantial agreement observed between IFAT and ELISA techniques (Kappa = 0.62) enables these methods as effective methodologies for the diagnosis of toxoplasmosis in chickens. The high prevalence of specific antibodies among poultry in the region studied attempts to the potential risk of transmission of toxoplasmosis to humans

Aspectos econômicos da produção de bovinos de corte

O Brasil ocupa as posições de maior produtor e exportador mundial de carne bovina, com a região Centro-Oeste respondendo por 35% do abate nacional, em 2010. Entretanto, faz-se necessário valorizar o planejamento, o controle e a gestão empresarial nas propriedades produtoras, visando ao lucro na atividade. O presente estudo objetivou analisar e avaliar a viabilidade econômica da produção de bovinos de corte, em Camapuã (MS), a fim de identificar os itens relevantes aos custos da atividade. Como direcionador dos custos variáveis, no custo operacional efetivo, o suplemento mineral fornecido aos animais e a mão de obra mostraram-se relevantes para a gestão do sistema de produção, representando, aproximadamente, 71% dos custos. Com base nos resultados apresentados, pôde-se concluir que a propriedade apresenta boa lucratividade (superior a 20%). Verificou-se, ainda, com base no fluxo de caixa, taxa interna de retorno de 13,13% e capital inicial investido retornando em, aproximadamente, 7 anos, com resultados atrativos para o investimento, neste segmento agropecuário. O estudo proporcionou um parâmetro de custo para o produtor pecuarista, podendo contribuir para um melhor planejamento de atividades, em que, apesar dos altos investimentos iniciais, possivelmente, poderá reduzir seus custos, com o manejo racional no sistema produtivo, o que seria mais atrativo para o mercado, tornando mais viáveis as suas atividades de produção e comercialização do produto.

Uso do bivalve límnico Anodontites tenebricosus (LEA, 1834) no biomonitoramento de metais do Rio Ribeira de Iguape

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Exigências energéticas para mantença e para o crescimento de frangos de corte

O trabalho foi realizado com o objetivo de determinar, pelo método fatorial, as exigências de energia metabolizável (EM) de frangos de corte. Foi conduzido um ensaio em câmaras climáticas mantidas às temperaturas de 13, 23 e 32ºC (±2ºC) para se verificar o efeito da temperatura sobre as exigências de energia metabolizável para mantença utilizando-se a técnica do abate comparativo. As exigências de energia metabolizável para ganho de peso foram determinadas com base no teor de energia corporal e na eficiência energética de utilização da EM. As exigências de mantença foram de 159,36; 116,17 e 128,66 kcal/kg0,75/dia para 13, 23 e 32ºC, respectivamente, verificando-se efeito quadrático da temperatura sobre as exigências de mantença (EMm=300,14 - 14,61.T + 0,2876.T², r²=0,90). As exigências de em para ganho de peso corporal foram de 3,72 kcal/g para machos e 3,98 kcal/g para fêmeas de 1 a 21 dias; 4,21 para machos e 3,93 para fêmeas de 22 a 42 dias; e 4,51 para machos e 7,04 para fêmeas de 43 a 56 dias. Considerando-se as exigências determinadas, foram elaborados modelos de predição das exigências diárias de energia para frangos de corte, nos quais foram considerados o peso corporal, a temperatura ambiente (para estimativa das exigências de mantença) e o ganho de peso (para cálculo das exigências de ganho). Com base nas comparações das exigências determinadas pelos modelos e nas recomendações do manual da linhagem, conclui-se que os modelos elaborados predizem as exigências energéticas dos frangos de corte.

Coeficientes de difusão de metais em materiais não convencionais (agarose e acetato de celulose) usados na técnica de difusão em filmes finos por gradientes de concentração

The DGT technique allows one to measure quantitatively free and labile metal species in aquatic systems. Nevertheless, for this approach, knowledge is required of the diffusion coefficients of the analytes in a diffusive layer. In this study, the diffusion coefficients of Hg(II), As(III), Mn(II), Mg(II), Cu(II), Cd(II) were determined in agarose gel and those of Ba(II), Cd(II), Cu(II), Mg(II), Mn(II) e Zn(II) in cellulose acetate membranes. These materials presented good performance and the reported results can be used as a data base for further DGT studies.

Semeadora-adubadora: mecanismos de corte de palha e cargas verticais aplicadas

This work had as objective to evaluate the performance of mechanisms of cutting of the no-tillage seedrills in different vegetable coverings and applied vertical loads. The experimental design used was in randomized blocks and factorial scheme 3 x 4, with four replications. The trials were accomplished with three different mechanisms of culting of the straw (plane disc, corrugated disc and wavy disc), using four different vertical loads (750, 1500, 2250 and 3000 N). All treatments were accomplished in five straw coverings (corn, sorghum, triticale, black oats and radish). The results showed that larger the amount of dry matter covering the soil, higher the demand of horizontal and vertical forces. The wavy disc promotes the largest values of area of mobilized soil and requires large horizontal force, vertical force and horizontal force per area of cutting depth of discs (specific force). The treatment with plane disc required higher values of the horizontal forces per area of mobilized soil and of vertical force in the corn and sorghum coverings.

Avaliação dos teores de metais pesados no solo e na planta de cana-de-açúcar sob adubação com lodo de esgoto e vinhaça

The objective of this work was to evaluate Cd, Cr, Ni and Pb total contents in soil and sugar cane after four annual applications of sewage sludge and vinasse to supply all N and all K required by the crop. A field experiment was carried out on clayey Typic Haplustox. It was used a randomized block design with seven treatments and three replications. The treatments consisted in: (i) rate of sewage sludge to supply 100% of the N required by the crop; (ii) rate of sewage sludge to supply 200% of the N required; (iii) rate of vinasse to supply 100% of the K required; (iv) rate of vinasse to supply 200% of the K required; ( v) combination of the treatments ( i) and ( iii); ( vi) combination of the treatments ( ii) e ( iv); (vii) control ( mineral fertilization). The contents of Cd, Cr, Ni and Pb in sewage sludge reached maximum values of 1.58, 41.66, 35.17 and 45.25 mg kg(-1), respectively. These metals were not detected in vinasse. The residues were applied annually for four years. At the end of this period, sewage sludge and vinasse accumulated rates, that get up to 51 t ha(-1) and 762 m(3) ha(-1), respectively, did not cause alteration in Cd, Cr, Ni and Pb total contents in soil, up to 50 cm of depth, and in plant. Sewage sludge and vinasse application to supply N and K for sugar cane did not offer soil pollution risk by heavy metals.