Simulation of Oil Shale Semi-Coke Particle Cold Transportation in a Spouted Bed Using CPFD Method

The spouted bed was widely used due to its good mixing of particles and effective phase transferability between the gas and solid phase. In this paper, the transportation process of particles in a 3D spouted bed was studied using the Computational Particle Fluid Dynamics (CPFD) numerical method. Experiments were conducted to verify the validity of the simulation results. Distributions of the pressure, velocities and particle concentration of transportation devices were investigated. The motion state and characteristics of multiphase flows in the transportation device were demonstrated under various operating conditions. The results showed that a good consistency was obtained between the simulated results and the experimental results. The motion characteristics of the gas-solid two-phase flow in the device was effectively predicted, which could assist the optimal operating condition estimation for the spouted transportation process.

Photoionization of Co+ and electron-impact excitation of Co2 + using the Dirac R-matrix method

Modelling of massive stars and supernovae (SNe) plays a crucial role in understanding galaxies. From this modelling we can derive fundamental constraints on stellar evolution, mass-loss processes, mixing, and the products of nucleosynthesis. Proper account must be taken of all important processes that populate and depopulate the levels (collisional excitation, de-excitation, ionization, recombination, photoionization, bound–bound processes). For the analysis of Type Ia SNe and core collapse SNe (Types Ib, Ic and II) Fe group elements are particularly important. Unfortunately little data is currently available and most noticeably absent are the photoionization cross-sections for the Fe-peaks which have high abundances in SNe. Important interactions for both photoionization and electron-impact excitation are calculated using the relativistic Dirac atomic R-matrix codes (DARC) for low-ionization stages of Cobalt. All results are calculated up to photon energies of 45 eV and electron energies up to 20 eV. The wavefunction representation of Co III has been generated using GRASP0 by including the dominant 3d⁷, 3d⁶[4s, 4p], 3p⁴3d⁹ and 3p⁶3d⁹ configurations, resulting in 292 fine structure levels. Electron-impact collision strengths and Maxwellian averaged effective collision strengths across a wide range of astrophysically relevant temperatures are computed for Co III. In addition, statistically weighted level-resolved ground and metastable photoionization cross-sections are presented for Co II and compared directly with existing work.

Analyzing Gene Centres with the Help of the Checklist Method – the Case of Syria

The present survey of species diversity of cultivated plants is the first for Syria. Some cultivated species will be added in the future, because due to the civil war in Syria, it was not possible to visit the country in the frame of the present work, as initially planned. Checklists proved to be a useful tool for overviewing the cultivated plants of selected areas and allow a characterization of the state of plant genetic resources of Syria. Syria has experienced several civilizations. Man settled in this productive land since ancient times and used its resources. However, such use has led to changes in vegetation and decline of wildlife through the country, in seashore areas, interior, mountains, and grassland. Plant domestication and growing started more than 10,000 years ago in West Asia. Since then, plentiful of economic plant species were present and used by man and his domesticated animals. Forming a part of the Fertile Crescent, where many of the world’s agricultural plants have evolved, Syria is extremely rich in agrobiodiversity. Wild progenitors of wheat and barley and wild relatives of many fruit trees such as almonds and pistachio as well as forage species are still found in marginal lands and less disturbed areas. These are threatened by a wide range of human activities, notably modern, extensive agriculture, overgrazing, overcutting and urban expansion. Syria is also considered as part of one of the main centres of origin, according to Vavilov, who had collected in Syria in 1926. The first expeditions to crop fields showed the exclusive nature of cultivated plants in Syria with a high number of endemic forms. Furthermore, Syria is a part of a biodiversity hotspot. Several studies have been performed to study agrobiodiversity in different parts of Syria, but usually on wild species. Many collections have been carried out; however, they focussed preferably on cereals and pulses, and particularly on wheat, like Vavilov’s expedition. Only 30 crops make up the major part of the conserved Syrian crop plant material in the genebank, indicating that most of the remaining 7,000 species of cultivated plants and many other valuable genetic resources species have only been included on a limited scale in the genebank collections. Although a small country (185,180 km2), Syria accommodates numerous ecosystems that allow for a large diversity of plant genetic resources for agriculture ranging from cold-requiring to subtropical crops to live and thrive. Only few references are available in this respect. The aim of the present study was to complete a checklist of Syria’s cultivated plants of agriculture and horticulture excluding plants only grown as ornamental or for forestry. Furthermore, plants taken for reforestation have not been included, if they do not have also agricultural or horticultural uses. Therefore, the inclusion of plants into the checklist follows the same principles as “Mansfeld’s Encyclopedia”. Main sources of information were published literature, floras of Syria, Lebanon and the Mediterranean, as well as Syrian printed sources in Arabic and/or English, reports from FAO on agricultural statistics in Syria, and data from ICARDA and Bioversity International. In addition, personal observations gathered during professional work in the General Commission for Scientific Agricultural Research (GCSAR) in Syria (since 1989) and participation in projects were taken into account. These were: (1) A project on “Conservation and Sustainable Use of Dry Land Agrobiodiversity in the Near East” with participation of Jordan, Lebanon, Syria, and the Palestinian Authority, focussing on landraces and wild relatives of barley, wheat, lentil, alliums, feed legumes, and fruit trees (1999–2005). (2) A project for vegetable landraces (1993–1995) in collaboration with the former International Plant Genetic Resources Institute and the UN Development Programme, in which 380 local vegetable accessions were evaluated. For medicinal plants and fruit trees I was in personal contact with departments of GCSAR and the Ministry of Agriculture and Agrarian Reform, as well as with private organizations. The resulting checklist was compared with the catalogues of crop plants of Italy and a checklist of cultivated plants of Iraq. The cultivated plant species are presented in alphabetical order according to their accepted scientific names. Each entry consists of a nomenclatural part, folk names, details of plant uses, the distribution in Syria (by provinces), a textual description, and references to literature. In total, 262 species belonging to 146 genera and 57 families were identified. Within-species (intraspecific) diversity is a significant measure of the biodiversity. Intraspecific diversity for wild plants has been and remains to be well studied, but for crop plants there are only few results. Mansfeld’s method is an actual logical contribution to such studies. Among the families, the following have the highest number of crop species: Leguminosae (34 spp.), Rosaceae (24), Gramineae (18), Labiatae (18), Compositae (14), Cruciferae (14), Cucurbitaceae (11), Rutaceae (10), Malvaceae (9), Alliaceae (7), and Anacardiaceae (7). The establishment of an effective programme for the maintenance of plant genetic resources in Syria started in the mid-1970s. This programme considered ex situ and in situ collection of the genetic resources of various field crops, fruit trees and vegetables. From a plant genetic resources viewpoint, it is clear that the homegarden is an important location for the cultivation of so-called neglected and underutilized species (neglected from a research side and underutilized from a larger economic side). Such species have so far not received much care from ecologists, botanists and agronomists, and they are considerably under-represented in genebanks.

Numerical analysis of the modal coupling at low resonances in a Colombian Andean Bandola in C using the finite element method

The work presented in this thesis is concerned with the dynamical behavior of a CBandola's acoustical box at low resonances -- Two models consisting of two and three coupled oscillators are proposed in order to analyse the response at the first two and three resonances, respectively -- These models describe the first resonances in a bandola as a combination of the lowest modes of vibration of enclosed air, top and back plates -- Physically, the coupling between these elements is caused by the fluid-structure interaction that gives rise to coupled modes of vibration for the assembled resonance box -- In this sense, the coupling in the models is expressed in terms of the ratio of effective areas and masses of the elements which is an useful parameter to control the coupling -- Numerical models are developed for the analysis of modal coupling which is performed using the Finite Element Method -- First, it is analysed the modal behavior of separate elements: enclosed air, top plate and back plate -- This step is important to identify participating modes in the coupling -- Then, a numerical model of the resonance box is used to compute the coupled modes -- The computation of normal modes of vibration was executed in the frequency range of 0-800Hz -- Although the introduced models of coupled oscillators only predict maximum the first three resonances, they also allow to study qualitatively the coupling between the rest of the computed modes in the range -- Considering that dynamic response of a structure can be described in terms of the modal parameters, this work represents, in a good approach, the basic behavior of a CBandola, although experimental measurements are suggested as further work to verify the obtained results and get more information about some characteristics of the coupled modes, for instance, the phase of vibration of the air mode and the radiation e ciency

A generic method of engagement to elicit regional coastal management options

Stakeholder engagement is important for successful management of natural resources, both to make effective decisions and to obtain support. However, in the context of coastal management, questions remain unanswered on how to effectively link decisions made at the catchment level with objectives for marine biodiversity and fisheries productivity. Moreover, there is much uncertainty on how to best elicit community input in a rigorous manner that supports management decisions. A decision support process is described that uses the adaptive management loop as its basis to elicit management objectives, priorities and management options using two case studies in the Great Barrier Reef, Australia. The approach described is then generalised for international interest. A hierarchical engagement model of local stakeholders, regional and senior managers is used. The result is a semi-quantitative generic elicitation framework that ultimately provides a prioritised list of management options in the context of clearly articulated management objectives that has widespread application for coastal communities worldwide. The case studies show that demand for local input and regional management is high, but local influences affect the relative success of both engagement processes and uptake by managers. Differences between case study outcomes highlight the importance of discussing objectives prior to suggesting management actions, and avoiding or minimising conflicts at the early stages of the process. Strong contributors to success are a) the provision of local information to the community group, and b) the early inclusion of senior managers and influencers in the group to ensure the intellectual and time investment is not compromised at the final stages of the process. The project has uncovered a conundrum in the significant gap between the way managers perceive their management actions and outcomes, and community's perception of the effectiveness (and wisdom) of these same management actions.

Banana peel: an effective biosorbent for aflatoxins

This work reports the application of banana peel as a novel bioadsorbent for in vitro removal of five mycotoxins (aflatoxins (AFB1, AFB2, AFG1, AFG2) and ochratoxin A). The effect of operational parameters including initial pH, adsorbent dose, contact time and temperature were studied in batch adsorption experiments. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and point of zero charge (pHpzc) analysis were used to characterise the adsorbent material. Aflatoxins’ adsorption equilibrium was achieved in 15 min, with highest adsorption at alkaline pH (6–8), while ochratoxin has not shown any significant adsorption due to surface charge repulsion. The experimental equilibrium data were tested by Langmuir, Freundlich and Hill isotherms. The Langmuir isotherm was found to be the best fitted model for aflatoxins, and the maximum monolayer coverage (Q0) was determined to be 8.4, 9.5, 0.4 and 1.1 ng mg−1 for AFB1, AFB2, AFG1 and AFG2 respectively. Thermodynamic parameters including changes in free energy (ΔG), enthalpy (ΔH) and entropy (ΔS) were determined for the four aflatoxins. Free energy change and enthalpy change demonstrated that the adsorption process was exothermic and spontaneous. Adsorption and desorption study at different pH further demonstrated that the sorption of toxins was strong enough to sustain pH changes that would be experienced in the gastrointestinal tract. This study suggests that biosorption of aflatoxins by dried banana peel may be an effective low-cost decontamination method for incorporation in animal feed diets. © 2016 Informa UK Limited, trading as Taylor & Francis Group.

A survey on prevalence rate of aflatoxigenic species of Aspergillus and residues of aflatoxins by ELISA method in cold-water cultural fish (rainbow trout) feeds in Tehran and West Azarbayjan provinces-Iran

Aflatoxins are one kind of fungal toxins produced by species of toxigenic Aspergillus (A. flavus and A. parasiticus) and in other words they are secondary metabolites which are considered as one of the threatening factors of food consumer's health. In this research 96 samples of cold-water cultural fish feed, rainbow trout, during the seasons of spring and summer of 2007 (every fifteenth of the month) were randomized (by simple and stratified random) to determine: 1. The prevalence rate of aflatoxigenic species of Aspergillus in stored feed of cold-water cultural fish in West Azarbayjan cultural fish farms in both seasons (spring and summer); 2. The residues of total aflatoxin in stored feed of fish in cultural fish farms of West Azarbayjan in both seasons by ELISA method; and 3. The residues of that toxin in feed produced in aquatic feed factories in Tehran and West Azarbyjan provinces with the same method. In order to study prevalence rate of toxigenic species of Aspergillus, pour-plate culture method by general medium such as Malt Extract Agar (M.E.A.) and Sabouraud-Dextrose Agar (S.D.A.) and by standard No.997 of Iranian Standard Institute were used. The produced colonies were examined microscopically. To determine the aflatoxins residues, ELISA method using Agra-Quant kit of Romer Lab company, were applied. The results of this survey indicated that only 8.3% of the samples were infected by A. flavus. A. parasiticus was not observed. There were no significant differences between the prevalence rate of AFT and seasons/months, either (P<0.05). Evaluating mean of aflatoxin rate showed that the rates of this variable are lower than the tolerance levels designated by the joint FAO/WHO expert committee (The mean of AFT in all data was lower than 11 ppb). Furthermore, mean of total AFT residues rates of stored feed of various cultural center of West Azarbayjan and Tehran factories were comparable in spring and summer, and no significant differences were observed (P<0.05). But there were significant differences between the total aflatoxin rates in the feed of West Azarbayjan factory and spring and summer (P<0.05), and AFT residues in spring (8.6 ppb) were higher than summer (6.1 ppb). Prevalence rates of AFT in Tehran feed factories (9.2 ppb) are higher than W. Azarbayjan (7.4 ppb). In other words, location was considered as a decisive factor in total AFT rates of samples. Moreover, the results indicated that there was significant difference between total aflatoxin rates of feed and cultural centers (P<0.05). The mean of AFT rates in embankment dam cultural fish farms (6.75 ppb) and multi-functions cultural fish farms (6.25 ppb) was higher than individual cultural pond (4.67 ppb). In conclusion, the finally results of this survey indicated that the lower rates of Aspergillus is not effective on the presence of total aflatoxin rates in trout feed. Due to low levels of aflatoxin rates (lower than 20 ppb), the produced feed of cold-cultural fishes, Rainbow Trout, in Tehran and West Azarbayjan provinces, in spring and summer of 2007, were safe and healthy both for fish and their consumers.

A deformation model of flexible, high area-to-mass ratio debris under perturbations and validation method

A new type of space debris was recently discovered by Schildknecht in near -geosynchronous orbit (GEO). These objects were later identified as exhibiting properties associated with High Area-to-Mass ratio (HAMR) objects. According to their brightness magnitudes (light curve), high rotation rates and composition properties (albedo, amount of specular and diffuse reflection, colour, etc), it is thought that these objects are multilayer insulation (MLI). Observations have shown that this debris type is very sensitive to environmental disturbances, particularly solar radiation pressure, due to the fact that their shapes are easily deformed leading to changes in the Area-to-Mass ratio (AMR) over time. This thesis proposes a simple effective flexible model of the thin, deformable membrane with two different methods. Firstly, this debris is modelled with Finite Element Analysis (FEA) by using Bernoulli-Euler theory called “Bernoulli model”. The Bernoulli model is constructed with beam elements consisting 2 nodes and each node has six degrees of freedom (DoF). The mass of membrane is distributed in beam elements. Secondly, the debris based on multibody dynamics theory call “Multibody model” is modelled as a series of lump masses, connected through flexible joints, representing the flexibility of the membrane itself. The mass of the membrane, albeit low, is taken into account with lump masses in the joints. The dynamic equations for the masses, including the constraints defined by the connecting rigid rod, are derived using fundamental Newtonian mechanics. The physical properties of both flexible models required by the models (membrane density, reflectivity, composition, etc.), are assumed to be those of multilayer insulation. Both flexible membrane models are then propagated together with classical orbital and attitude equations of motion near GEO region to predict the orbital evolution under the perturbations of solar radiation pressure, Earth’s gravity field, luni-solar gravitational fields and self-shadowing effect. These results are then compared to two rigid body models (cannonball and flat rigid plate). In this investigation, when comparing with a rigid model, the evolutions of orbital elements of the flexible models indicate the difference of inclination and secular eccentricity evolutions, rapid irregular attitude motion and unstable cross-section area due to a deformation over time. Then, the Monte Carlo simulations by varying initial attitude dynamics and deformed angle are investigated and compared with rigid models over 100 days. As the results of the simulations, the different initial conditions provide unique orbital motions, which is significantly different in term of orbital motions of both rigid models. Furthermore, this thesis presents a methodology to determine the material dynamic properties of thin membranes and validates the deformation of the multibody model with real MLI materials. Experiments are performed in a high vacuum chamber (10-4 mbar) replicating space environment. A thin membrane is hinged at one end but free at the other. The free motion experiment, the first experiment, is a free vibration test to determine the damping coefficient and natural frequency of the thin membrane. In this test, the membrane is allowed to fall freely in the chamber with the motion tracked and captured through high velocity video frames. A Kalman filter technique is implemented in the tracking algorithm to reduce noise and increase the tracking accuracy of the oscillating motion. The forced motion experiment, the last test, is performed to determine the deformation characteristics of the object. A high power spotlight (500-2000W) is used to illuminate the MLI and the displacements are measured by means of a high resolution laser sensor. Finite Element Analysis (FEA) and multibody dynamics of the experimental setups are used for the validation of the flexible model by comparing with the experimental results of displacements and natural frequencies.

Endoscopic sleeve gastroplasty (the Apollo method): a new approach to obesity management

Background: Many obese patients cannot lose weight or reject conventional obesity management. Endoscopic sleeve gastroplasty (the Apollo method) is a pioneering coadjuvant, interventionist technique for the integral management of obesity. Objectives: The goals of this study were to report safety and efficacy results obtained at 6 months in patients undergoing endoscopic sleeve gastroplasty. Material and methods: A prospective study was performed in 55 patients (13 males, 42 females) who were subjected to the Apollo technique; mean age was 43.5 years (range 25-60) and mean BMI was 37.7 kg/m² (range 30-48). All received multidisciplinary follow-up for weight loss. Weight changes and presence of complications were assessed. Through the endoscope a triangular pattern suture is performed consisting of approximately 3-6 transmural (mucosa to serosa) stitches, using a cinch device to bring them nearer and form a plication. Results: A total of 6-8 plications are used to provide a tubular or sleeve-shaped restriction to the gastric cavity. No major complications developed and patients were discharged at 24 hours following the procedure. Endoscopic and radiographic follow-up at 6 months post-procedure showed a well preserved tubular form to the stomach. After 6 months patients had lost 18.9 kg and 55.3% of excess weight. Conclusions: Endoscopic sleeve gastroplasty, together with dietary and psycho-behavioral changes, is a safe, effective technique in the coadjuvant management of obese patients.

Learning Binary Code Representations for Effective and Efficient Image Retrieval

The size of online image datasets is constantly increasing. Considering an image dataset with millions of images, image retrieval becomes a seemingly intractable problem for exhaustive similarity search algorithms. Hashing methods, which encodes high-dimensional descriptors into compact binary strings, have become very popular because of their high efficiency in search and storage capacity. In the first part, we propose a multimodal retrieval method based on latent feature models. The procedure consists of a nonparametric Bayesian framework for learning underlying semantically meaningful abstract features in a multimodal dataset, a probabilistic retrieval model that allows cross-modal queries and an extension model for relevance feedback. In the second part, we focus on supervised hashing with kernels. We describe a flexible hashing procedure that treats binary codes and pairwise semantic similarity as latent and observed variables, respectively, in a probabilistic model based on Gaussian processes for binary classification. We present a scalable inference algorithm with the sparse pseudo-input Gaussian process (SPGP) model and distributed computing. In the last part, we define an incremental hashing strategy for dynamic databases where new images are added to the databases frequently. The method is based on a two-stage classification framework using binary and multi-class SVMs. The proposed method also enforces balance in binary codes by an imbalance penalty to obtain higher quality binary codes. We learn hash functions by an efficient algorithm where the NP-hard problem of finding optimal binary codes is solved via cyclic coordinate descent and SVMs are trained in a parallelized incremental manner. For modifications like adding images from an unseen class, we propose an incremental procedure for effective and efficient updates to the previous hash functions. Experiments on three large-scale image datasets demonstrate that the incremental strategy is capable of efficiently updating hash functions to the same retrieval performance as hashing from scratch.

Development of an organocatalytic method for the enantioselective synthesis of rivastigmine

The focus of this thesis was the study of a recently developed class of picolinamide cinchona alkaloid derivatives for the synthesis of Rivastigmine, a biologically active compound used for the treatment of Alzheimer’s disease. Six 9-picolinamide-cinchona alkaloid derivatives were successfully synthesized through simple and effective methods. These catalysts were then applied in the enantioselective reduction of O-protected ketimines (intermediates of Rivastigmine). The hydrosilylation of the N-phenyl ketimines afforded good results with excellent yields and high enantioselectivities, while much lower values, in terms of both enantioselectivity and yield, were obtained in the reduction of N-benzyl ketimines. Preliminary studies on the immobilization of these organocatalysts to different solid supports were conducted, with the purpose of applying them in continuous flow systems, which to date has never been reported; RESUMO: No âmbito deste trabalho, foi estudada a síntese de um composto biologicamente ativo usado para o tratamento da doença de Alzheimer, Rivastigmina, usando uma classe de picolinamidas derivadas de alcaloides de cinchona recentemente desenvolvida. Seis 9-picolinamida derivados de alcaloides de cinchona foram preparados com êxito através de metodologias simples e eficazes. Os organocatalisadores foram posteriormente aplicados na redução enantiosseletiva de cetiminas O-protegidas (intermediários de Rivastigmina). Foram obtidos bons resultados na hidrossililação de N-fenilo cetiminas, com rendimentos excelentes e elevadas enantiosseletividades, enquanto a redução de N-benzilo cetiminas proporcionou valores muito mais baixos, tanto em termos de rendimento como de enantiosseletividade. Com o objetivo de serem aplicados em sistemas de fluxo contínuo, realizaram-se estudos preliminares sobre a imobilização destes organocatalisadores em diferentes suportes sólidos, a qual, ate à data, ainda não foi descrita na literatura.

MULTI-BAND BOSE HUBBARD MODELS AND EFFECTIVE THREE-BODY INTERACTIONS

Experiments with ultracold atoms in optical lattice have become a versatile testing ground to study diverse quantum many-body Hamiltonians. A single-band Bose-Hubbard (BH) Hamiltonian was first proposed to describe these systems in 1998 and its associated quantum phase-transition was subsequently observed in 2002. Over the years, there has been a rapid progress in experimental realizations of more complex lattice geometries, leading to more exotic BH Hamiltonians with contributions from excited bands, and modified tunneling and interaction energies. There has also been interesting theoretical insights and experimental studies on “un- conventional” Bose-Einstein condensates in optical lattices and predictions of rich orbital physics in higher bands. In this thesis, I present our results on several multi- band BH models and emergent quantum phenomena. In particular, I study optical lattices with two local minima per unit cell and show that the low energy states of a multi-band BH Hamiltonian with only pairwise interactions is equivalent to an effec- tive single-band Hamiltonian with strong three-body interactions. I also propose a second method to create three-body interactions in ultracold gases of bosonic atoms in a optical lattice. In this case, this is achieved by a careful cancellation of two contributions in the pair-wise interaction between the atoms, one proportional to the zero-energy scattering length and a second proportional to the effective range. I subsequently study the physics of Bose-Einstein condensation in the second band of a double-well 2D lattice and show that the collision aided decay rate of the con- densate to the ground band is smaller than the tunneling rate between neighboring unit cells. Finally, I propose a numerical method using the discrete variable repre- sentation for constructing real-valued Wannier functions localized in a unit cell for optical lattices. The developed numerical method is general and can be applied to a wide array of optical lattice geometries in one, two or three dimensions.

STUDY OF A DIRECT SAMPLING METHOD FOR THE INVERSE MEDIUM SCATTERING PROBLEM

Direct sampling methods are increasingly being used to solve the inverse medium scattering problem to estimate the shape of the scattering object. A simple direct method using one incident wave and multiple measurements was proposed by Ito, Jin and Zou. In this report, we performed some analytic and numerical studies of the direct sampling method. The method was found to be effective in general. However, there are a few exceptions exposed in the investigation. Analytic solutions in different situations were studied to verify the viability of the method while numerical tests were used to validate the effectiveness of the method.

APPLICATION OF AN IMPUTATION METHOD FOR GEOSPATIAL INVENTORY OF FOREST STRUCTURAL ATTRIBUTES ACROSS MULTIPLE SPATIAL SCALES IN THE LAKE STATES, U.S.A.

Credible spatial information characterizing the structure and site quality of forests is critical to sustainable forest management and planning, especially given the increasing demands and threats to forest products and services. Forest managers and planners are required to evaluate forest conditions over a broad range of scales, contingent on operational or reporting requirements. Traditionally, forest inventory estimates are generated via a design-based approach that involves generalizing sample plot measurements to characterize an unknown population across a larger area of interest. However, field plot measurements are costly and as a consequence spatial coverage is limited. Remote sensing technologies have shown remarkable success in augmenting limited sample plot data to generate stand- and landscape-level spatial predictions of forest inventory attributes. Further enhancement of forest inventory approaches that couple field measurements with cutting edge remotely sensed and geospatial datasets are essential to sustainable forest management. We evaluated a novel Random Forest based k Nearest Neighbors (RF-kNN) imputation approach to couple remote sensing and geospatial data with field inventory collected by different sampling methods to generate forest inventory information across large spatial extents. The forest inventory data collected by the FIA program of US Forest Service was integrated with optical remote sensing and other geospatial datasets to produce biomass distribution maps for a part of the Lake States and species-specific site index maps for the entire Lake State. Targeting small-area application of the state-of-art remote sensing, LiDAR (light detection and ranging) data was integrated with the field data collected by an inexpensive method, called variable plot sampling, in the Ford Forest of Michigan Tech to derive standing volume map in a cost-effective way. The outputs of the RF-kNN imputation were compared with independent validation datasets and extant map products based on different sampling and modeling strategies. The RF-kNN modeling approach was found to be very effective, especially for large-area estimation, and produced results statistically equivalent to the field observations or the estimates derived from secondary data sources. The models are useful to resource managers for operational and strategic purposes.