METHANE DRY REFORMING OVER Ni SUPPORTED ON PINE SAWDUST ACTIVATED CARBON: EFFECTS OF SUPPORT SURFACE PROPERTIES AND METAL LOADING

The influence of metal loading and support surface functional groups (SFG) on methane dry reforming (MDR) over Ni catalysts supported on pine-sawdust derived activated carbon were studied. Using pine sawdust as the catalyst support precursor, the smallest variety and lowest concentration of SFG led to best Ni dispersion and highest catalytic activity, which increased with Ni loading up to 3 Ni atoms nm-2. At higher Ni loading, the formation of large metal aggregates was observed, consistent with a lower "apparen" surface area and a decrease in catalytic activity. The H2/CO ratio rose with increasing reaction temperature, indicating that increasingly important side reactions were taking place in addition to MDR.

PYROLIGNEOUS LIQUOR PRODUCED FROM ACACIA MEARNSII DE WILD WOOD UNDER CONTROLLED CONDITIONS AS A RENEWABLE SOURCE OF CHEMICALS

Acacia mearnsii de Wild (black wattle) is one of the most important trees planted in Southern Brazil for tannin extraction and charcoal production. The pyrolysis of the black wattle wood used for obtaining charcoal is performed in brick ovens, with the gas fraction being sent directly into the environment. The present study examines the condensable compounds present in the liquor produced from black wattle wood at different thermal degradation conditions, using gas chromatography coupled with mass spectrometry (GC/MS). Branches of black wattle were thermally degraded at controlled ambient and temperature conditions. Overall, a higher variety of compounds were obtained under atmospheric air pressure than under synthetic air pressure. Most of the tentatively identified compounds, such as carboxylic acids, phenols, aldehydes, and low molecular mass lignin fragments, such as guayacol, syringol, and eugenol, were products of lignin thermoconversion. Substituted aromatic compounds, such as vanillin, ethyl vanillin, and 2-methoxy-4-propeny-phenol, were also identified. At temperatures above 200 ºC, furan, 2-acetylfuran, methyl-2-furoate, and furfural, amongst others, were identified as polysaccharide derivatives from cellulose and hemicellulose depolymerization. This study evidences the need for adequate management of the condensable by-products of charcoal production, both for economic reasons and for controlling their potential environmental impact.

Chemigation with benomyl and fluazinam and their fungicidal effects in soil for white mold control on dry beans

The effectiveness of fungicides in controlling white mold (Sclerotinia sclerotiorum) of dry beans (Phaseolus vulgaris) was evaluated when they were applied through irrigation water directly onto the plants or only to the soil. Two field trials were installed in April 1998 and April 1999 in Viçosa, MG. Trials were conducted as a (2 x 3) + 1 factorial: two fungicides x three application modes + one untreated control. The fungicides were benomyl (1.0 kg a.i. ha-1) and fluazinam (0.5 l a.i. ha-1). The three application modes were: (a) by backpack sprayer (667 l ha-1), (b) by garden watering-cans simulating sprinkler irrigation with 35,000 l ha-1 of water, and (c) by garden watering-cans applying water between the rows and near the soil surface in 35,000 l ha-1 of water. In 1998, fungicides were applied at 43 and 54 days after emergence (DAE); in 1999, at 47 and 61 DAE. Both fungicides were similarly effective on white mold control when applied by either chemigation or backpack sprayer, resulting in yields 21% higher than untreated control. Only fluazinam provided disease control when applications were made only in soil. Chemigation provided white mold control equivalent to that of backpack sprayer in terms of incidence, severity and number of diseased pods. Consequently, yield differences between these application methods were not significant.

Pretreatment in membrane filtration of wood hydrolysate

Interest in recovery of valuable components from process streams has increased in recent years. Purpose of biorefinery is to utilize components that otherwise would go to waste. Hemicelluloses, for example, could be utilized in production of many valuable products. One possible way to separate and fractionate hemicelluloses is membrane filtration. In the literature part of this work membrane fouling in filtration processes of pulp and paper process- and wastewaters was investigated. Especially purpose was to find out the possible fouling compounds, after which facilities to remove or modify such components less harmful were studied. In the experimental part different pretreatment methods, mainly to remove or degrade lignin from wood hydrolysate, were studied. In addition, concentration of hemicelluloses and separation from lignin were examined with two ultrafiltration membranes; UFX5 and RC70PP. Changes in feed solution, filtration capacity and fouling of membranes were used to evaluate the effects of pretreatment methods. Changes in hydrolysate composition were observed with different analysis methods. Filtration of hydrolysate proved to be challenging, especially with the UFX5 membrane. The more hydrophilic RC70PP membrane did not seem to be fouled as severely as the UFX5 membrane, according to pure water flux measurements. The UFX5 membrane retained hemicelluloses rather well, but problems arose from rapid flux decline resulting from concentration polarization and fouling of membrane. Most effective pretreatment methods in the case with the UFX5 membrane proved to be prefiltration with the RC70PP membrane, activated carbon adsorption and photocatalytic oxidation using titanium dioxide and UV radiation. An additional experiment with PHW extract showed that pulsed corona discharge treatment degraded lignin quite efficiently and thus improved filtration capacity remarkably, even over six times compared to the filtration with untreated extract.

Utilization of retention chemicals in non-wood containing furnishes

The usage of the non-wood pulps in furnishes for various paper grades is the real alternative for substitution of wood fibres in the papermaking. This is especially important now, when the prices for wood are increasing and forest resources are depleting in many regions of our planet. However, there are several problems associated with utilization of such pulps. In terms of the papermaking process one of the main problems is the poor dewatering of the non-wood pulps. This problem can be partially solved by means of retention aids. In the literature part were described technological features of the non-wood pulps as the raw materials for paper production. Moreover, overviews of the retention chemicals and methods for retention measurement were done; special attention was paid to the mechanisms of retention and drainage. Finally, factors affecting on the drainage and retention of non-wood pulps were considered holistically. Particular emphasis was put on the possibility of enzyme treatment for drainage improvement. It was stated that retention aids can significantly improve dewatering of non-wood pulps. In the experimental part the goal was to investigate influence of various microparticle retention aids on the drainage, retention and formation of furnish containing wheat straw pulp, obtained by novel pulping process (Formico™Fib). The parallel test were performed with reference furnish containing only wood pulps. It was found that Bentonite-CPAM retention aid can significantly improve drainage and retention; however formation seems be suffer from such additives. It was stated that performance of the Silica-Starch retention aid significantly depends on the starch dosing sequence and wet-end conditions; this system have shown better formation than other tested retention aids. Silica-CPAM retention aid have provided comparable results in retention and drainage with Bentonite-CPAM, while Silica-starch did not improve dewatering and yielded in lowest filler retention among other aids. Ultimately, optimal dosages for the tested retention chemicals have been suggested.

Utilization of non-wood pulp in different fibers products

The correct utilization of non-wood raw material allows reducing tree cutting and reduces emissions of carbon dioxide from burning of non-wood plants on farmers fields. Also it allows increasing economical situation in regions that non-wood plants are grown and where they are converted into pulp and paper. Also it gives positive effect on population pressure of work by addition of working place. In the literature survey included an overview of the historical meaning of non-wood pulp on developing paper production and structure of non-wood pulps. Moreover, anatomical and chemical composition of straw, reed and bamboo were studied more detailed. Also, an overview of the utilization of non-wood pulp in papermaking was made. Especially tissue, tree-free and release papers were reviewed. In the experimental part the goal was to investigate suitability of non-wood pulp like wheat straw pulp and bamboo pulp for different fiber products. Finally release and tree-free paper products were selected for experimental studies. It was discovered that wheat straw, especially screened wheat straw, showed good results for release paper. Also utilization of wheat straw and bamboo pulp in tree-free paper showed good results and suitability of these non-wood pulps for tree-free paper production. Also it was noticed that addition of wheat straw pulp gave positive effect on initial wet strength for release and tree-free paper.

Economy of converting wood to biocoal

The pre-treatment step has a significant influence on the performance of bioenergy chains, especially on logistics. In nowadays conditions it is important to have technologies allowing to convert biomass at modest scales into dense energy carriers that ease transportation and handling. There are such technologies as charring and torrefaction. It is a thermal treatment of organic waste (only woody biomass is considered as a raw material in this work), which aims to produce a fuel with increased energy density. Wood processing is attractive under meaning of green house gas emissions. Charring and torrefaction are promising technologies due to its high process efficiency. It may be also attractive in the future as a renewable fuel with improved storage properties, increased energy density (compared to raw wood) for co-combustion and/or gasification.

Financial and Environmental Impacts of a Dry Port to Facilitate Competitiveness of Two Major Transit Seaports of Finland

Environmental problems and issues have received more and more attention during the last decades. Reasons for this are different increased external costs such as congestion, CO2 emission, noise and accident costs. Transportation sector is the only sector with increasing external costs. The EU will increase its attention in decreasing the external costs of transport. Aim of this research was to find out if a dry port solution could decrease costs of transport, especially external costs. Dry port concept is an intermodal transport system, where inland transport between port and dry port is performed by rail transport instead of traditional road transport. In addition, dry ports offer similar services as ports. Research is conducted by performing a literature review about dry port concept and costs of transport, especially external costs of transport. Financial and environmental impacts of the dry port concept are studied by comparing costs of road and rail transport by cost accounting and with a simulation model. Location of dry port is researched with gravitational models. Results of the literature review are that rail transport is environmentally friendlier mode of transport than road transport. Cost model and simulation model show that if only costs of freight movement are considered, rail transport is more inexpensive transport mode than road transport in terms of internal and external costs. Because of that dry port concept could decrease costs of transport, especially external costs. Results of gravitational models are that city of Kouvola is in a good position to be a dry port. Russian transit traffic through Finland improves location of Kouvola to be a dry port.

Diagnosing and developing knowledge management capability –Knowledge management capability in UPM-Kymmene Wood Oy

The purpose of this case study is to clarify how KM (knowledge management) capability is constructed through six different activities and to explore how this capability can be diagnosed and developed in the three case organizations. The study examines the knowledge management capability of the three factories in UPM-Kymmene Wood Oy, a major Finnish plywood producer. Forest industry is usually considered to be quite hierarchical. The importance of leveraging employee skills and knowledge has been recognized in all types of organizations – including those that mainly deal with tangible resources. However, the largest part of empirical knowledge management literature examines KM in so called knowledge-intensive or knowledge-based organizations. This study extends existing literature by providing an in depth case study into assessment and development of KM activities in these three organizations with little awareness of the KM discourse. This subject is analyzed through literature review, theoretical analysis and empirical research in the case organizations. The study also presents a structured method for evaluating KM activities of a company and for diagnosing the main weaknesses that should be developed in order to achieve KM excellence. The results help in understanding how knowledge management capability is constructed and provide insight into developing and exploiting it within an organization.

On the potential utilisation of sawdust and wood chip screenings

This work is based on the utilisation of sawdust and wood chip screenings for different purposes. A substantial amount of these byproducts are readily available in the Finnish forest industry. A black liquor impregnation study showed that sawdust-like wood material behaves differently from normal chips. Furthermore, the fractionation and removal of the smallest size fractions did not have a significant effect on the impregnation of sawdust-like wood material. Sawdust kraft cooking equipped with an impregnation stage increases the cooking yield and decreases the lignin content of the produced pulp. Impregnation also increases viscosity of the pulp and decreases chlorine dioxide consumption in bleaching. In addition, impregnation increases certain pulp properties after refining. Hydrotropic extraction showed that more lignin can be extracted from hardwood than softwood. However, the particle size had a major influence on the lignin extraction. It was possible to extract more lignin from spruce sawdust than spruce chips. Wood chip screenings are usually combusted to generate energy. They can also be used in the production of kraft pulp, ethanol and chemicals. It is not economical to produce ethanol from wood chip screenings because of the expensive wood material. Instead, they should be used for production of steam and energy, kraft pulp and higher value added chemicals. Bleached sawdust kraft pulp can be used to replace softwood kraft pulp in mechanical pulp based papers because it can improve certain physical properties. It is economically more feasible to use bleached sawdust kraft pulp in stead of softwood kraft pulp, especially when the reinforcement power requirement is moderate.

Harvesting and wood transport planning with SNAP III program (Scheduling and Network Analysis Program) in a pine plantation in Southeast Brazil

The objective of this study was to verify the potential of SNAP III (Scheduling and Network Analysis Program) as a support tool for harvesting and wood transport planning in Brazil harvesting subsystem definition and establishment of a compatible route were assessed. Initially, machine operational and production costs were determined in seven subsystems for the study area, and quality indexes, construction and maintenance costs of forest roads were obtained and used as SNAP III program input data. The results showed, that three categories of forest road occurrence were observed in the study area: main, secondary and tertiary which, based on quality index, allowed a medium vehicle speed of about 41, 30 and 24 km/hours and a construction cost of about US$ 5,084.30, US$ 2,275.28 and US$ 1,650.00/km, respectively. The SNAP III program used as a support tool for the planning, was found to have a high potential tool in the harvesting and wood transport planning. The program was capable of defining efficiently, the harvesting subsystem on technical and economical basis, the best wood transport route and the forest road to be used in each period of the horizon planning.