Prediction of the Temperature Distribution of Partially Submersed Umbilical Cables

The objective of this work is to predict the temperature distribution of partially submersed umbilical cables under different operating and environmental conditions. The commercial code Fluent (R) was used to simulate the heat transfer and the air fluid flow of part of a vertical umbilical cable near the air-water interface. A free-convective three-dimensional turbulent flow in open-ended vertical annuli was solved. The influence of parameters such as the heat dissipating rate, wind velocity, air temperature and solar radiation was analyzed. The influence of the presence of a radiation shield consisting of a partially submersed cylindrical steel tube was also considered. The air flow and the buoyancy-driven convective heat transfer in the annular region between the steel tube and the umbilical cable were calculated using the standard k-epsilon turbulence model. The radiative heat transfer between the umbilical external surface and the radiation shield was calculated using the Discrete Ordinates model. The results indicate that the influence of a hot environment and intense solar radiation may affect the umbilical cable performance in its dry portion.

Kinetic resolution of alpha-bromophenylacetamides using quinine or Cinchona alkaloid salts

The kinetic resolution of racemic alpha-bromophenylacetamides 1 was achieved in the presence of benzenethiolate and Cinchona alkaloid salts as phase-transfer catalysts or benzenethiol and quinine, yielding (S)-enantioenriched alpha-sulfanylated products. The observed stereoselection was rationalized on the basis of the best fitting of 1 and the resolving agent in the ternary complexes. (C) 2012 Elsevier Ltd. All rights reserved.

D-S(+) meson production at central rapidity in proton-proton collisions at root s=7 TeV

The P-T-differential inclusive production cross section of the prompt charm-strange meson D-s(+) in the rapidity range vertical bar y vertical bar < 0.5 was measured in proton-proton collisions at root s = 7 TeV at the LHC using the ALICE detector. The analysis was performed on a data sample of 2.98 x 10(8) events collected with a minimum-bias trigger. The corresponding integrated luminosity is L-int = 4.8 nb(-1). Reconstructing the decay D-s(+) -> phi pi(+) with phi -> K-K+, and its charge conjugate, about 480 D-s(+/-) mesons were counted, after selection cuts, in the transverse momentum range 2 < P-T < 12 GeV/c. The results are compared with predictions from models based on perturbative QCD. The ratios of the cross sections of four D meson species (namely D-0, D+, D*+ and D-s(+)) were determined both as a function of p(T) and integrated over p(T)after extrapolating to full p(T) range, together with the strangeness suppression factor in charm fragmentation. The obtained values are found to be compatible within uncertainties with those measured by other experiments in e(+)e(-), ep and pp interactions at various centre-of-mass energies. (C) 2012 CERN. Published by Elsevier By. All rights reserved.

Detailed H-1 and C-13 NMR structural assignment and relative stereochemistry determination for three new and one known semi-synthetic sesquiterpene lactones

In this work is described a complete H-1 and C-13 NMR analysis for a group of four sesquiterpene lactones, three previously unknown. The unequivocal assignments were achieved by H-1 NMR, C-13{H-1} NMR, gCOSY. gHMQC, gHMBC and NOESY experiments and no ambiguities were left behind. All hydrogen coupling constants were measured, clarifying all hydrogen signals multiplicities. (C) 2011 Elsevier B.V. All rights reserved.

Análise crítica das recomendações do uso das vacinas meningocócicas conjugadas

OBJETIVOS: Analisar a epidemiologia da doença meningocócica no Brasil e o impacto que as recentes evidências acumuladas com a incorporação das vacinas meningocócicas C conjugadas nos programas de imunização podem ter nas diferentes estratégias de uso dessas vacinas. FONTES DOS DADOS: Revisão nas bases de dados MEDLINE, SciELO e LILACS no período de 2000 a 2011. SÍNTESE DOS DADOS: No Brasil, a doença meningocócica é endêmica, com ocorrência periódica de surtos. Os maiores coeficientes de incidência ocorrem em lactentes, sendo o sorogrupo C responsável pela maioria dos casos, motivando a introdução da vacina meningocócica C conjugada no Programa Nacional de Imunizações, em 2010, para crianças menores de 2 anos. A introdução das vacinas meningocócicas C conjugadas nos programas de imunização na Europa, Canadá e Austrália mostrou-se efetiva, com dramática redução na incidência de doença causada pelo sorogrupo C, não apenas nos vacinados, mas também em não vacinados. A efetividade em longo prazo dessas vacinas mostrou-se dependente de uma combinação de persistência de anticorpos, memória imunológica e proteção indireta. Recentes evidências indicando que a persistência de anticorpos não é duradoura em crianças pequenas imunizadas e que a memória imunológica não é rápida o suficiente para protegê-las contra a doença enfatizam a importância da proteção indireta para manutenção da população protegida. CONCLUSÕES: A rápida queda de títulos de anticorpos em crianças vacinadas nos primeiros anos de vida sugere a necessidade de incorporarmos doses de reforço antes da adolescência, especialmente em locais como o Brasil, onde ainda não contamos com o efeito da proteção indireta da população.

Prediction of the temperature distribution of partially submersed umbilical cables

The objective of this work is to predict the temperature distribution of partially submersed umbilical cables under different operating and environmental conditions. The commercial code Fluent® was used to simulate the heat transfer and the air fluid flow of part of a vertical umbilical cable near the air-water interface. A free-convective three-dimensional turbulent flow in open-ended vertical annuli was solved. The influence of parameters such as the heat dissipating rate, wind velocity, air temperature and solar radiation was analyzed. The influence of the presence of a radiation shield consisting of a partially submersed cylindrical steel tube was also considered. The air flow and the buoyancydriven convective heat transfer in the annular region between the steel tube and the umbilical cable were calculated using the standard k-ε turbulence model. The radiative heat transfer between the umbilical external surface and the radiation shield was calculated using the Discrete Ordinates model. The results indicate that the influence of a hot environment and intense solar radiation may affect the umbilical cable performance in its dry portion.

Rigidity for piecewise smooth homeomorphisms on the circle

We find conditions for two piecewise 'C POT.2+V' homeomorphisms f and g of the circle to be 'C POT.1' conjugate. Besides the restrictions on the combinatorics of the maps (we assume that the maps have bounded combinatorics), and necessary conditions on the one-side derivatives of points where f and g are not differentiable, we also assume zero mean-nonlinearity for f and g.

Matrix-vector multiplication and triangular linear solver using GPGPU for symmetric positive definite matrices derived from elliptic equations

The modern GPUs are well suited for intensive computational tasks and massive parallel computation. Sparse matrix multiplication and linear triangular solver are the most important and heavily used kernels in scientific computation, and several challenges in developing a high performance kernel with the two modules is investigated. The main interest it to solve linear systems derived from the elliptic equations with triangular elements. The resulting linear system has a symmetric positive definite matrix. The sparse matrix is stored in the compressed sparse row (CSR) format. It is proposed a CUDA algorithm to execute the matrix vector multiplication using directly the CSR format. A dependence tree algorithm is used to determine which variables the linear triangular solver can determine in parallel. To increase the number of the parallel threads, a coloring graph algorithm is implemented to reorder the mesh numbering in a pre-processing phase. The proposed method is compared with parallel and serial available libraries. The results show that the proposed method improves the computation cost of the matrix vector multiplication. The pre-processing associated with the triangular solver needs to be executed just once in the proposed method. The conjugate gradient method was implemented and showed similar convergence rate for all the compared methods. The proposed method showed significant smaller execution time.

Design and Characterization of New Luminescent Sensors and Labels

The aim of this Ph.D. project has been the design and characterization of new and more efficient luminescent tools, in particular sensors and labels, for analytical chemistry, medical diagnostics and imaging. Actually both the increasing temporal and spatial resolutions that are demanded by those branches, coupled to a sensitivity that is required to reach the single molecule resolution, can be provided by the wide range of techniques based on luminescence spectroscopy. As far as the development of new chemical sensors is concerned, as chemists we were interested in the preparation of new, efficient, sensing materials. In this context, we kept developing new molecular chemosensors, by exploiting the supramolecular approach, for different classes of analytes. In particular we studied a family of luminescent tetrapodal-hosts based on aminopyridinium units with pyrenyl groups for the detection of anions. These systems exhibited noticeable changes in the photophysical properties, depending on the nature of the anion; in particular, addition of chloride resulted in a conformational change, giving an initial increase in excimeric emission. A good selectivity for dicarboxylic acid was also found. In the search for higher sensitivities, we moved our attention also to systems able to perform amplification effects. In this context we described the metal ion binding properties of three photoactive poly-(arylene ethynylene) co-polymers with different complexing units and we highlighted, for one of them, a ten-fold amplification of the response in case of addition of Zn2+, Cu2+ and Hg2+ ions. In addition, we were able to demonstrate the formation of complexes with Yb3+ an Er3+ and an efficient sensitization of their typical metal centered NIR emission upon excitation of the polymer structure, this feature being of particular interest for their possible applications in optical imaging and in optical amplification for telecommunication purposes. An amplification effect was also observed during this research in silica nanoparticles derivatized with a suitable zinc probe. In this case we were able to prove, for the first time, that nanoparticles can work as “off-on” chemosensors with signal amplification. Fluorescent silica nanoparticles can be thus seen as innovative multicomponent systems in which the organization of photophysically active units gives rise to fruitful collective effects. These precious effects can be exploited for biological imaging, medical diagnostic and therapeutics, as evidenced also by some results reported in this thesis. In particular, the observed amplification effect has been obtained thanks to a suitable organization of molecular probe units onto the surface of the nanoparticles. In the effort of reaching a deeper inside in the mechanisms which lead to the final amplification effects, we also attempted to find a correlation between the synthetic route and the final organization of the active molecules in the silica network, and thus with those mutual interactions between one another which result in the emerging, collective behavior, responsible for the desired signal amplification. In this context, we firstly investigated the process of formation of silica nanoparticles doped with pyrene derivative and we showed that the dyes are not uniformly dispersed inside the silica matrix; thus, core-shell structures can be formed spontaneously in a one step synthesis. Moreover, as far as the design of new labels is concerned, we reported a new synthetic approach to obtain a class of robust, biocompatible silica core-shell nanoparticles able to show a long-term stability. Taking advantage of this new approach we also showed the synthesis and photophysical properties of core-shell NIR absorbing and emitting materials that proved to be very valuable for in-vivo imaging. In general, the dye doped silica nanoparticles prepared in the framework of this project can conjugate unique properties, such as a very high brightness, due to the possibility to include many fluorophores per nanoparticle, high stability, because of the shielding effect of the silica matrix, and, to date, no toxicity, with a simple and low-cost preparation. All these features make these nanostructures suitable to reach the low detection limits that are nowadays required for effective clinical and environmental applications, fulfilling in this way the initial expectations of this research project.

Design and synthesis of novel non peptidomimtic beta-secretase inhibitors in the treatment of Alzheimer's disease

The aspartic protease BACE1 (β-amyloid precursor protein cleaving enzyme, β-secretase) is recognized as one of the most promising targets in the treatment of Alzheimer's disease (AD). The accumulation of β-amyloid peptide (Aβ) in the brain is a major factor in the pathogenesis of AD. Aβ is formed by initial cleavage of β-amyloid precursor protein (APP) by β-secretase, therefore BACE1 inhibition represents one of the therapeutic approaches to control progression of AD, by preventing the abnormal generation of Aβ. For this reason, in the last decade, many research efforts have focused at the identification of new BACE1 inhibitors as drug candidates. Generally, BACE1 inhibitors are grouped into two families: substrate-based inhibitors, designed as peptidomimetic inhibitors, and non-peptidomimetic ones. The research on non-peptidomimetic small molecules BACE1 inhibitors remains the most interesting approach, since these compounds hold an improved bioavailability after systemic administration, due to a good blood-brain barrier permeability in comparison to peptidomimetic inhibitors. Very recently, our research group discovered a new promising lead compound for the treatment of AD, named lipocrine, a hybrid derivative between lipoic acid and the AChE inhibitor (AChEI) tacrine, characterized by a tetrahydroacridinic moiety. Lipocrine is one of the first compounds able to inhibit the catalytic activity of AChE and AChE-induced amyloid-β aggregation and to protect against reactive oxygen species. Due to this interesting profile, lipocrine was also evaluated for BACE1 inhibitory activity, resulting in a potent lead compound for BACE1 inhibition. Starting from this interesting profile, a series of tetrahydroacridine analogues were synthesised varying the chain length between the two fragments. Moreover, following the approach of combining in a single molecule two different pharmacophores, we designed and synthesised different compounds bearing the moieties of known AChEIs (rivastigmine and caproctamine) coupled with lipoic acid, since it was shown that dithiolane group is an important structural feature of lipocrine for the optimal inhibition of BACE1. All the tetrahydroacridines, rivastigmine and caproctamine-based compounds, were evaluated for BACE1 inhibitory activity in a FRET (fluorescence resonance energy transfer) enzymatic assay (test A). With the aim to enhancing the biological activity of the lead compound, we applied the molecular simplification approach to design and synthesize novel heterocyclic compounds related to lipocrine, in which the tetrahydroacridine moiety was replaced by 4-amino-quinoline or 4-amino-quinazoline rings. All the synthesized compounds were also evaluated in a modified FRET enzymatic assay (test B), changing the fluorescent substrate for enzymatic BACE1 cleavage. This test method guided deep structure-activity relationships for BACE1 inhibition on the most promising quinazoline-based derivatives. By varying the substituent on the 2-position of the quinazoline ring and by replacing the lipoic acid residue in lateral chain with different moieties (i.e. trans-ferulic acid, a known antioxidant molecule), a series of quinazoline derivatives were obtained. In order to confirm inhibitory activity of the most active compounds, they were evaluated with a third FRET assay (test C) which, surprisingly, did not confirm the previous good activity profiles. An evaluation study of kinetic parameters of the three assays revealed that method C is endowed with the best specificity and enzymatic efficiency. Biological evaluation of the modified 2,4-diamino-quinazoline derivatives measured through the method C, allow to obtain a new lead compound bearing the trans-ferulic acid residue coupled to 2,4-diamino-quinazoline core endowed with a good BACE1 inhibitory activity (IC50 = 0.8 mM). We reported on the variability of the results in the three different FRET assays that are known to have some disadvantages in term of interference rates that are strongly dependent on compound properties. The observed results variability could be also ascribed to different enzyme origin, varied substrate and different fluorescent groups. The inhibitors should be tested on a parallel screening in order to have a more reliable data prior to be tested into cellular assay. With this aim, preliminary cellular BACE1 inhibition assay carried out on lipocrine confirmed a good cellular activity profile (EC50 = 3.7 mM) strengthening the idea to find a small molecule non-peptidomimetic compound as BACE1 inhibitor. In conclusion, the present study allowed to identify a new lead compound endowed with BACE1 inhibitory activity in submicromolar range. Further lead optimization to the obtained derivative is needed in order to obtain a more potent and a selective BACE1 inhibitor based on 2,4-diamino-quinazoline scaffold. A side project related to the synthesis of novel enzymatic inhibitors of BACE1 in order to explore the pseudopeptidic transition-state isosteres chemistry was carried out during research stage at Università de Montrèal (Canada) in Hanessian's group. The aim of this work has been the synthesis of the δ-aminocyclohexane carboxylic acid motif with stereochemically defined substitution to incorporating such a constrained core in potential BACE1 inhibitors. This fragment, endowed with reduced peptidic character, is not known in the context of peptidomimetic design. In particular, we envisioned an alternative route based on an organocatalytic asymmetric conjugate addition of nitroalkanes to cyclohexenone in presence of D-proline and trans-2,5-dimethylpiperazine. The enantioenriched obtained 3-(α-nitroalkyl)-cyclohexanones were further functionalized to give the corresponding δ-nitroalkyl cyclohexane carboxylic acids. These intermediates were elaborated to the target structures 3-(α-aminoalkyl)-1-cyclohexane carboxylic acids in a new readily accessible way.

Doxorubicina coniugata alla albumina umana lattosaminata: azione antineoplastica sui carcinomi epatocellulari indotti nel ratto dalla dietilnitrosammina

The experiments described in the thesis for my PhD were addressed to the study of the anticancer activity of a conjugate of doxorubicin (DOXO) with lactosaminated human albumin (L-HSA) on hepatocellular carcinomas (HCCs) induced in rats by diethylnitrosamine. L-HSA is a neoglycoprotein exposing galactosyl residues. The conjugate was prepared to improve the chemo therapeutic index of DOXO in the treatment of the well differentiated (WD) HCCs whose cells mantain the receptor for galactosyl terminating glycoproteins and consequently can actively internalize L-HSA. In my first experiments I found that L-HSA coupled DOXO produced concentrations of DOXO higher than those raised by an equal dose of free drug, not only in WD HCCs, but also in the poorly differentiated forms (PD) of these tumors which do no express the receptor for galactosyl terminating glycoproteins. Subsequently I provided evidence that penetration of L-HSA-DOXO in PD HCCs was due to a non-specific adsorption mediated by the DOXO residues of the conjugate which interact with the cell surface mainly because at physiological pH they are positively charged and bind to anionic phospholipids of the cell membrane. In subsequent experiments, by ultrasound technique, I studied the action of free and L-HSA coupled DOXO on the growth of rat HCCs. I found that L-HSA coupled DOXO hindered the development of new neoplastic nodules and inhibited the growth of the established tumors. In contrast, the free drug neither inhibited the development of HCCs nor prevented the growth of the established tumors. Moreover, the free drug produced a severe loss of weight of rats, a sign of severe toxicity, which was not caused by the conjugate. In conclusion assuming that the results obtained in rats can be applied to patients, the results of my thesis suggest that the conjugate by increasing the efficacy and tolerability of DOXO could improve the value of this drug in the treatment of human HCCs.

Mechanismen der Aktivierung und Detoxifizierung von Aflatoxin B 1 in verschiedenen Leberzelltypen von Ratten, Mäusen und Waldmurmeltieren

Zusammenfassung: Die Applikation des Mykotoxins Aflatoxin B1 (AFB1) führt in der Ratte zu Lebertumoren hepatozellulären Ursprungs, während bisher keine transformierende Wirkung dieses Mykotoxins auf Kupffer- und Endothelzellen (Nichtparenchymzellen, NPC) nachgewiesen werden konnte. Diese Resistenzmechanismen der NPC gegenüber AFB1 wurden im ersten Teil dieser Arbeit untersucht. AFB1 ist per se inaktiv, wird jedoch durch Verstoffwechselung in den chemisch reaktiven, an DNA bindenden Metaboliten AFB1-8,9-Epoxid überführt. Daneben stellt die enzymatische Hydroxylierung von AFB1 am Kohlenstoff-9a zum Aflatoxin M1 eine Detoxifizierung dar. Durch HPLC-Analyse der AFB1-Metabolite konnte gezeigt werden, daß in Nichtparenchymzellen (NPC) das Verhältnis von 9a-Hydroxylierung zu 8,9-Epoxidierung höher als in Parenchymzellen (PC) ist. Die AFB1-9a-hydroxylase fördert insbesondere in den NPC der Leber die Bildung des weniger gentoxischen Metaboliten AFM1 und konkurriert daher um die Aktivierung von AFB1 zum mutagenen und kanzerogenen 8,9-Epoxid. Dieser metabolische Unterschied scheint also einen Beitrag zur Resistenz der NPC der Leber gegenüber der hepatokanzerogenen Wirkung von AFB1 zu leisten. Da ein Synergismus zwischen der AFB1-Exposition und einer Infektion mit dem Hepatitis B-Virus (HBV) beim Menschen bezüglich des Auftretens von hepatozellulären Karzinomen zu bestehen scheint, wurde im zweiten Teil dieser Arbeit untersucht, ob die metabolische Aktivierung von AFB1 durch eine HBV-Infektion verstärkt wird. In einem Vergleich der Biotransformation von AFB1 mit mikrosomalen Leberfraktionen von transgenen HBV-Mäusen und Kontrollmäusen wurde keine signifikanten Unterschiede festgestellt. Dagegen wurde bei Virus-infizierten Waldmurmeltieren eine deutlich reduzierte Bildung des AFB1-8,9-Epoxids beobachtet. Es konnte z.T. ein Zusammenhang zwischen den verschiedenen Stadien der Leberschädigung und den Metabolismusraten festgestellt werden, wobei die metabolische Aktivierung mit zunehmender Leberschädigung abzunehmen scheint. Auch hinsichtlich der Aktivitäten verschiedener Cytochrom P450 abhängiger Monooxygenasen wurde eine weitgehende Übereinstimmung mit den durch HPLC ermittelten Metabolitenprofilen des AFB1 beobachtet. Diese Studien mit subzellulären Leberfraktion der transgenen HBV-Mäusen und der Waldmurmeltieren zeigen, daß die Interaktion zwischen Hepatitis und AFB1 nicht mit der verstärkten metabolischer Aktivierung von AFB1 zu erklären ist. TGF-ß1, aus der Gruppe der Cytokine, wird als Mediator bei Entzündungsprozessen in der Leber so z.B. im Verlauf einer Virushepatitis freigesetzt. Aufgrund der besonderen Bedeutung des murinen CYP2A5 (ortholog zum humanen CYP2A6) bei der Aktivierung von AFB1 wurde der Einfluß von TGF-ß1 auf CYP2A5 in Primärkulturen von Maushepatozyten untersucht. Durch Messung der Aktivität der Cumarin-7-hydroxylase sowie durch Bestimmung der Proteinmenge von CYP2A5 mittels Western Blotting konnte zunächst die Induzierbarkeit des CYP2A5-Isoenzyms durch Phenobarbital in kultivierten Hepatozyten der Maus gezeigt werden. Nur bei einer niedrigen TGF-ß1-Konzentration wurde eine leicht erhöhte Expression von CYP2A5 festgestellt, ansonsten führte die Behandlung der kultivierten Maushepatozyten mit TGF-ß1 zu einer dosisabhängigen Verminderung der Expression von CYP2A5.

Synthese und Charakterisierung von Modellen für Photoschalter und elektronische Ventile

Gegenstand der vorliegenden Arbeit war die Synthese von organischen Photoschalter-Modellen auf der Basis von mesoionischen Pyrimidinium-olaten und Bis(thienylperfluorocyclopentenen), sowie die Darstellung substituierter Biphenyl-Biradikale als Modelle für Ventil-Systeme im Sinne eines neuen Schalter-Ventil-Konzeptes.Aufbauend auf meiner Arbeit über mesoionische Pyrimidinium-olate wurde ein henkelverbrücktes Ansa-Mesoion mit einem 16-gliedrigen Makrocyclus, sowie drei mehrcyclische mesoionische Systeme synthetisiert und auf ihr Schaltverhalten hin untersucht. Das Ansa-Mesoion stellt ein erstes einfaches Modell für Schalter-Ventil-Konjugate dar. Zur Darstellung der photochromen Bis(thienylethene) wurden die aus der Literatur bekannten Syntheserouten nach Irie als auch nach Feringa auf neue Strukturen angewandt und die Schalteigenschaften der Bis(thienylethene) optisch nachgewiesen. Die Anordnung der reaktiven Endgruppen in den synthetisierten Verbindungen schafft ideale Voraussetzungen für eine große konformelle Änderung, welche im Schalter-Ventil-Konjugat erwünscht ist. Durch vielfaches Durchlaufen des Schaltprozesses (> 100 Cyclen) konnte die hohe Reversibilität des Schaltvorganges belegt werden.Als Ventilmodelle wurden mit stabilen Nitroxidradikalen substituierte Biphenyle verwendet, deren primärer konformativer Freiheitsgrad durch die Drehung um die Phenyl-Phenyl-Einfachbindung gegeben ist. Experimentelle ESR-Daten und deren Vergleich mit Spektrensimulationen bestätigten die Abhängigkeit der Austauschwechselwirkung J zwischen den Radikalen vom Biphenyldiederwinkel.

Kinematic description of the rupture from strong motion data: strategies for a robust inversion

We present a non linear technique to invert strong motion records with the aim of obtaining the final slip and rupture velocity distributions on the fault plane. In this thesis, the ground motion simulation is obtained evaluating the representation integral in the frequency. The Green’s tractions are computed using the discrete wave-number integration technique that provides the full wave-field in a 1D layered propagation medium. The representation integral is computed through a finite elements technique, based on a Delaunay’s triangulation on the fault plane. The rupture velocity is defined on a coarser regular grid and rupture times are computed by integration of the eikonal equation. For the inversion, the slip distribution is parameterized by 2D overlapping Gaussian functions, which can easily relate the spectrum of the possible solutions with the minimum resolvable wavelength, related to source-station distribution and data processing. The inverse problem is solved by a two-step procedure aimed at separating the computation of the rupture velocity from the evaluation of the slip distribution, the latter being a linear problem, when the rupture velocity is fixed. The non-linear step is solved by optimization of an L2 misfit function between synthetic and real seismograms, and solution is searched by the use of the Neighbourhood Algorithm. The conjugate gradient method is used to solve the linear step instead. The developed methodology has been applied to the M7.2, Iwate Nairiku Miyagi, Japan, earthquake. The estimated magnitude seismic moment is 2.6326 dyne∙cm that corresponds to a moment magnitude MW 6.9 while the mean the rupture velocity is 2.0 km/s. A large slip patch extends from the hypocenter to the southern shallow part of the fault plane. A second relatively large slip patch is found in the northern shallow part. Finally, we gave a quantitative estimation of errors associates with the parameters.

The grain-scale distribution and behaviour of melt and fluid in crystalline analogue systems

The production, segregation and migration of melt and aqueous fluids (henceforth called liquid) plays an important role for the transport of mass and energy within the mantle and the crust of the Earth. Many properties of large-scale liquid migration processes such as the permeability of a rock matrix or the initial segregation of newly formed liquid from the host-rock depends on the grain-scale distribution and behaviour of liquid. Although the general mechanisms of liquid distribution at the grain-scale are well understood, the influence of possibly important modifying processes such as static recrystallization, deformation, and chemical disequilibrium on the liquid distribution is not well constrained. For this thesis analogue experiments were used that allowed to investigate the interplay of these different mechanisms in-situ. In high-temperature environments where melts are produced, the grain-scale distribution in “equilibrium” is fully determined by the liquid fraction and the ratio between the solid-solid and the solid-liquid surface energy. The latter is commonly expressed as the dihedral or wetting angle between two grains and the liquid phase (Chapter 2). The interplay of this “equilibrium” liquid distribution with ongoing surface energy driven recrystallization is investigated in Chapter 4 and 5 with experiments using norcamphor plus ethanol liquid. Ethanol in contact with norcamphor forms a wetting angle of about 25°, which is similar to reported angles of rock-forming minerals in contact with silicate melt. The experiments in Chapter 4 show that previously reported disequilibrium features such as trapped liquid lenses, fully-wetted grain boundaries, and large liquid pockets can be explained by the interplay of the liquid with ongoing recrystallization. Closer inspection of dihedral angles in Chapter 5 reveals that the wetting angles are themselves modified by grain coarsening. Ongoing recrystallization constantly moves liquid-filled triple junctions, thereby altering the wetting angles dynamically as a function of the triple junction velocity. A polycrystalline aggregate will therefore always display a range of equilibrium and dynamic wetting angles at raised temperature, rather than a single wetting angle as previously thought. For the deformation experiments partially molten KNO3–LiNO3 experiments were used in addition to norcamphor–ethanol experiments (Chapter 6). Three deformation regimes were observed. At a high bulk liquid fraction >10 vol.% the aggregate deformed by compaction and granular flow. At a “moderate” liquid fraction, the aggregate deformed mainly by grain boundary sliding (GBS) that was localized into conjugate shear zones. At a low liquid fraction, the grains of the aggregate formed a supporting framework that deformed internally by crystal plastic deformation or diffusion creep. Liquid segregation was most efficient during framework deformation, while GBS lead to slow liquid segregation or even liquid dispersion in the deforming areas.