Effectiveness of Electrochemical Chloride Extraction for the Iowa Avenue Pedestrian Bridge, TR-499, 2005

The main objective of this study is to determine the effectiveness of the Electrochemical Chloride Extraction (ECE) technique on a bridge deck with very high concentrations of chloride. This ECE technique was used during the summer of 2003 to reverse the effects of corrosion, which had occurred in the reinforcing steel embedded in the pedestrian bridge deck over Highway 6, along Iowa Avenue, in Iowa City, Iowa, USA. First, the half cell potential was measured to determine the existing corrosion level in the field. The half-cell potential values were in the indecisive range of corrosion (between -200 mV and -350 mV). The ECE technique was then applied to remove the chloride from the bridge deck. The chloride content in the deck was significantly reduced from 25 lb/cy to 4.96 lb/cy in 8 weeks. Concrete cores obtained from the deck were measured for their compressive strengths and there was no reduction in strength due to the ECE technique. Laboratory tests were also performed to demonstrate the effectiveness of the ECE process. In order to simulate the corrosion in the bridge deck, two reinforced slabs and 12 reinforced beams were prepared. First, the half-cell potentials were measured from the test specimens and they all ranged below -200 mV. Upon introduction of 3% salt solution, the potential reached up to -500 mV. This potential was maintained while a salt solution was being added for six months. The ECE technique was then applied to the test specimens in order to remove the chloride from them. Half-cell potential was measured to determine if the ECE technique can effectively reduce the level of corrosion.

Fibroblastic reticular cells from lymph nodes attenuate T cell expansion by producing nitric oxide.

Adaptive immune responses are initiated when T cells encounter antigen on dendritic cells (DC) in T zones of secondary lymphoid organs. T zones contain a 3-dimensional scaffold of fibroblastic reticular cells (FRC) but currently it is unclear how FRC influence T cell activation. Here we report that FRC lines and ex vivo FRC inhibit T cell proliferation but not differentiation. FRC share this feature with fibroblasts from non-lymphoid tissues as well as mesenchymal stromal cells. We identified FRC as strong source of nitric oxide (NO) thereby directly dampening T cell expansion as well as reducing the T cell priming capacity of DC. The expression of inducible nitric oxide synthase (iNOS) was up-regulated in a subset of FRC by both DC-signals as well as interferon-γ produced by primed CD8+ T cells. Importantly, iNOS expression was induced during viral infection in vivo in both LN FRC and DC. As a consequence, the primary T cell response was found to be exaggerated in Inos(-/-) mice. Our findings highlight that in addition to their established positive roles in T cell responses FRC and DC cooperate in a negative feedback loop to attenuate T cell expansion during acute inflammation.

Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

Automatic Segmentation of the Eye in 3D Magnetic Resonance Imaging: A Novel Statistical Shape Model for Treatment Planning of Retinoblastoma.

PURPOSE: Proper delineation of ocular anatomy in 3-dimensional (3D) imaging is a big challenge, particularly when developing treatment plans for ocular diseases. Magnetic resonance imaging (MRI) is presently used in clinical practice for diagnosis confirmation and treatment planning for treatment of retinoblastoma in infants, where it serves as a source of information, complementary to the fundus or ultrasonographic imaging. Here we present a framework to fully automatically segment the eye anatomy for MRI based on 3D active shape models (ASM), and we validate the results and present a proof of concept to automatically segment pathological eyes. METHODS AND MATERIALS: Manual and automatic segmentation were performed in 24 images of healthy children's eyes (3.29 ± 2.15 years of age). Imaging was performed using a 3-T MRI scanner. The ASM consists of the lens, the vitreous humor, the sclera, and the cornea. The model was fitted by first automatically detecting the position of the eye center, the lens, and the optic nerve, and then aligning the model and fitting it to the patient. We validated our segmentation method by using a leave-one-out cross-validation. The segmentation results were evaluated by measuring the overlap, using the Dice similarity coefficient (DSC) and the mean distance error. RESULTS: We obtained a DSC of 94.90 ± 2.12% for the sclera and the cornea, 94.72 ± 1.89% for the vitreous humor, and 85.16 ± 4.91% for the lens. The mean distance error was 0.26 ± 0.09 mm. The entire process took 14 seconds on average per eye. CONCLUSION: We provide a reliable and accurate tool that enables clinicians to automatically segment the sclera, the cornea, the vitreous humor, and the lens, using MRI. We additionally present a proof of concept for fully automatically segmenting eye pathology. This tool reduces the time needed for eye shape delineation and thus can help clinicians when planning eye treatment and confirming the extent of the tumor.

Measurement systems in wall production applications

Tässä tutkimuksessa kehitettiin prototyyppi betonielementin dimension mittaus järjestelmästä. Tämä järjestelmä mahdollistaa kolmiulotteisen kappaleen mittauksen. Tutkimuksessa kehitettiin myös stereonäköön perustuva kappaleen mittaus. Prototyyppiä testailin ja tulokset osoittautuivat luotettaviksi. Tutkimuksessa selvitetään ja vertaillaan myös muita lähestymistapoja ja olemassa olevia järjestelmiä kappaleen kolmiuloitteiseen mittaukseen, joita Suomalaiset yhtiöt käyttävät tällä alalla.

Flexible Multibody Simulation Approach in the Dynamic Analysis of Bone Strains Activity

The objective of this study is to show that bone strains due to dynamic mechanical loading during physical activity can be analysed using the flexible multibody simulation approach. Strains within the bone tissue play a major role in bone (re)modeling. Based on previous studies, it has been shown that dynamic loading seems to be more important for bone (re)modeling than static loading. The finite element method has been used previously to assess bone strains. However, the finite element method may be limited to static analysis of bone strains due to the expensive computation required for dynamic analysis, especially for a biomechanical system consisting of several bodies. Further, in vivo implementation of strain gauges on the surfaces of bone has been used previously in order to quantify the mechanical loading environment of the skeleton. However, in vivo strain measurement requires invasive methodology, which is challenging and limited to certain regions of superficial bones only, such as the anterior surface of the tibia. In this study, an alternative numerical approach to analyzing in vivo strains, based on the flexible multibody simulation approach, is proposed. In order to investigate the reliability of the proposed approach, three 3-dimensional musculoskeletal models where the right tibia is assumed to be flexible, are used as demonstration examples. The models are employed in a forward dynamics simulation in order to predict the tibial strains during walking on a level exercise. The flexible tibial model is developed using the actual geometry of the subject’s tibia, which is obtained from 3 dimensional reconstruction of Magnetic Resonance Images. Inverse dynamics simulation based on motion capture data obtained from walking at a constant velocity is used to calculate the desired contraction trajectory for each muscle. In the forward dynamics simulation, a proportional derivative servo controller is used to calculate each muscle force required to reproduce the motion, based on the desired muscle contraction trajectory obtained from the inverse dynamics simulation. Experimental measurements are used to verify the models and check the accuracy of the models in replicating the realistic mechanical loading environment measured from the walking test. The predicted strain results by the models show consistency with literature-based in vivo strain measurements. In conclusion, the non-invasive flexible multibody simulation approach may be used as a surrogate for experimental bone strain measurement, and thus be of use in detailed strain estimation of bones in different applications. Consequently, the information obtained from the present approach might be useful in clinical applications, including optimizing implant design and devising exercises to prevent bone fragility, accelerate fracture healing and reduce osteoporotic bone loss.

Adsorción física sobre sólidos: aspectos termodinámicos

A thermodynamic formalism based on the Gibbs Dividing Surface (GDS) for the description of a solid-fluid interface is presented, so that the adsorption layer is understand as a phase and the adsorption process as the transference of components between a 3-dimensional phase and a 2-dimensional one. Using a state equation derived from the Henry's Law, we shall show how the Langmuir isotherm is deduced from de Gibbs isotherm. The GDS is useful also for understanding the release of heat by a system as the adsorption occurs.

Ba-DOPED ZnO MATERIALS: A DFT SIMULATION TO INVESTIGATE THE DOPING EFFECT ON FERROELECTRICITY

ZnO is a semiconductor material largely employed in the development of several electronic and optical devices due to its unique electronic, optical, piezo-, ferroelectric and structural properties. This study evaluates the properties of Ba-doped wurtzite-ZnO using quantum mechanical simulations based on the Density Functional Theory (DFT) allied to hybrid functional B3LYP. The Ba-doping caused increase in lattice parameters and slight distortions at the unit cell angle in a wurtzite structure. In addition, the doping process presented decrease in the band-gap (Eg) at low percentages suggesting band-gap engineering. For low doping amounts, the wavelength characteristic was observed in the visible range; whereas, for middle and high doping amounts, the wavelength belongs to the Ultraviolet range. The Ba atoms also influence the ferroelectric property, which is improved linearly with the doping amount, except for doping at 100% or wurtzite-BaO. The ferroelectric results indicate the ZnO:Ba is an strong option to replace perovskite materials in ferroelectric and flash-type memory devices.

COMPARAÇÃO ENTRE FUNCIONAIS DE DENSIDADE NO ESTUDO DE PROPRIEDADES ELETRÔNICAS DE DERIVADOS DA ARTEMISININA

The present paper demonstrates the application of functional GGA hybrids, with long-range corrections, for the calculation of the electronic properties of artemisinin and two of its derivatives - artemether e artesunate. Due to the relatively large amount of data obtained, the statistical method of Principal Component Analysis was employed. The functionals of the WB97 family are observed to be the most appropriate for the determining of reactivity indexes, which are the principal descriptors that, probably, are associated with the antimalarial and anticancer properties of this group of molecules. In addition, it was also observed that all the functionals obtained satisfactorily describe the geometric properties of the studied.

Distribution development in global business environment

The purpose of this master’s thesis was to analyze a case company’s distribution and its elements. With different distribution structure options a customer can be served with different ways. However, cost elements and service elements create different trade-offs. In this work the case company’s distribution’s present state was analyzed and conclusions were made. Based on these conclusions different alternatives for distribution were created. These different alternatives were analyzed through simulations and with more traditional calculations to compose the total operative costs of each alternative. Also other aspects were considered, such as required organizational changes and the possible better customer service. With the suggested 3-stock distribution structure shorter delivery times and possibly more punctual deliveries for products kept in stock could be achieved with the same operative costs as in current direct delivery model. Also, similar benefits could be achieved with other products with the 3-stock model.

Diversidade e estrutura de fragmentos de mata de várzea e de mata mesófila semidecídua submontana do rio Jacaré-Pepira (SP)

O objetivo deste trabalho é de comparar a diversidade específica e a estrutura comunitária de mata de várzea (MV), inundada anualmente, e de mata mesófila semidecídua submontana (MS) situada em áreas adjacentes a cursos d’água, mas que não sofre inundações freqüentes. Para realizar esta comparação, foram estudados 15 fragmentos de mata ao longo do rio Jacaré-Pepira, no centro do estado de São Paulo. Utilizou-se o método de quadrantes para amostrar os indivíduos dos estratos arbóreo e arbustivo com 3 cm ou mais de diâmetro do caule a 1,3 m de altura do solo. Os fragmentos de MV apresentam uma baixa diversidade (1,6 nats/tree £ H’ £ 2,9 nats/ind.) em relação aos fragmentos de MS (3,2 nats/ind. £ H’ £ 4,3 nats/ind.). Essa diferença é significativa numa análise discriminante (F= 9,544, p= 0,013). No entanto, alguns fragmentos podem conter os dois tipos de mata (MV e MS) e apresentarem, então, valores altos de diversidade (H’ próximo de 3,9 nats/ind.). Em relação à densidade total (DT) e à área basal total (ABT), os valores apresentam grandes variações, particularmente para os fragmentos de MS (2040 ind./ha £ DT £ 5479 ind./ha; 21,05 m2/ha £ ABT £ 65,35 m2/ha). Nenhum destes dois parâmetros permite distinguir significativamente MS de MV (p > 0,05). Os valores do Índice de Valor de Cobertura (IVC) mostram que os fragmentos de MV apresentam sempre as mesmas espécies de maior IVC (Croton urucurana e Inga affinis ), enquanto os fragmentos de MS apresentam uma grande variedade de espécies de maior IVC, apesar dos levantamentos terem sido feitos num trecho curto do rio e em condições semelhantes de solo e topografia. Nas bordas dos rios, existe uma faixa de mata transicional, de largura variável em função do relevo e da descarga do rio, que apresenta estruturas intermediárias entre as de MV e MS.

Estrutura fitossociológica da comunidade de lianas em uma floresta estacional semidecidual na Fazenda Canchim, São Carlos, SP

Foi realizado um estudo fitossociológico de lianas em uma floresta estacional semidecidual na Fazenda Canchim - Embrapa/CPPSE. A floresta formada por dois fragmentos, possui uma área total de 112 ha, localizada a 21º57' S e 47º50' W. Foram amostrados em 75 parcelas de 10 × 10 m todos os indivíduos de lianas que apresentavam diâmetro maior ou igual a 2,5 cm a uma distância de 1,3 m a partir da base do caule fixo no solo. Foram encontrados 528 indivíduos, pertencentes a 45 espécies, o que representou uma diversidade específica (H') de 3,20 nats. Bignoniaceae, Malpighiaceae, Sapindaceae e Apocynaceae foram as famílias com maior número de espécies e, juntas, representaram 71,11% do total amostrado. A espécie com maior valor de importância (VI) foi Mansoa difficilis (Cham.) Bureau & K. Schum. Os indivíduos amostrados apresentaram pequenos diâmetros e somente quatro tiveram diâmetros maiores que 10 cm.

A new paradigm for the folding of ribonucleic acids

De récentes découvertes montrent le rôle important que joue l’acide ribonucléique (ARN) au sein des cellules, que ce soit le contrôle de l’expression génétique, la régulation de plusieurs processus homéostasiques, en plus de la transcription et la traduction de l’acide désoxyribonucléique (ADN) en protéine. Si l’on veut comprendre comment la cellule fonctionne, nous devons d’abords comprendre ses composantes et comment ils interagissent, et en particulier chez l’ARN. La fonction d’une molécule est tributaire de sa structure tridimensionnelle (3D). Or, déterminer expérimentalement la structure 3D d’un ARN s’avère fort coûteux. Les méthodes courantes de prédiction par ordinateur de la structure d’un ARN ne tiennent compte que des appariements classiques ou canoniques, similaires à ceux de la fameuse structure en double-hélice de l’ADN. Ici, nous avons amélioré la prédiction de structures d’ARN en tenant compte de tous les types possibles d’appariements, dont ceux dits non-canoniques. Cela est rendu possible dans le contexte d’un nouveau paradigme pour le repliement des ARN, basé sur les motifs cycliques de nucléotides ; des blocs de bases pour la construction des ARN. De plus, nous avons dévelopées de nouvelles métriques pour quantifier la précision des méthodes de prédiction des structures 3D des ARN, vue l’introduction récente de plusieurs de ces méthodes. Enfin, nous avons évalué le pouvoir prédictif des nouvelles techniques de sondage de basse résolution des structures d’ARN.

Long-term effects of sports concussion

Questions : Cette thèse visait à répondre à deux questions fondamentales : 1) Est-ce que les athlètes qui présentent un historique de commotions cérébrales du sport en conservent des effets délétères à long terme? ; et 2) Est-ce que les effets néfastes des commotions cérébrales récurrentes sur le fonctionnement tant cognitif que moteur sont cumulatifs? Devis expérimental : À l’aide d’un plan d’investigation double-cohorte réalisé avec un groupe d’athlètes évoluant au niveau universitaire et un autre formé d’anciens athlètes universitaires testés plus de trois décennies plus tard, les quatre études qui composent cette thèse ont employé des méthodes raffinées d’investigation des fonctions cognitives et motrices pour en déceler des atteintes persistantes. Méthodologie : Les potentiels évoqués cognitifs ainsi que les tests neuropsychologiques ont permis de sonder le fonctionnement cognitif de ces athlètes alors que la stimulation magnétique transcrânienne, une plateforme de force permettant de mesurer la stabilité posturale ainsi qu’un système d’enregistrement tridimensionnel des mouvements rapides alternatifs ont servi à l’évaluation de l’intégrité du système moteur. Résultats : Cette thèse a permis de déceler des altérations persistentes et cumulatives des fonctions cognitives et motrices. De plus, ces subtiles atteintes observées chez les jeunes athlètes, affectant essentiellement des marqueurs neurophysiologiques sous-cliniques du fonctionnement cognitif et moteur, s’étaient accentuées chez les anciens athlètes universitaires qui montraient un déclin quantifiable tant des fonctions cognitives que motrices. Discussion : Ces résultats suggèrent d’une part que les commotions cérébrales du sport entraînent des altérations cognitives et motrices chroniques qui s’accentuent en fonction du nombre de commotions cérébrales subies. D’autre part, les effets délétères des commotions cérébrales du sport sur le fonctionnement cognitif et moteur combinés à ceux associés au processus de vieillissement entraînent un déclin cognitif et moteur quantifiable en comparaison aux anciens athlètes n’ayant jamais subi de commotions cérébrales.

Statistical potentials for evolutionary studies

Les séquences protéiques naturelles sont le résultat net de l’interaction entre les mécanismes de mutation, de sélection naturelle et de dérive stochastique au cours des temps évolutifs. Les modèles probabilistes d’évolution moléculaire qui tiennent compte de ces différents facteurs ont été substantiellement améliorés au cours des dernières années. En particulier, ont été proposés des modèles incorporant explicitement la structure des protéines et les interdépendances entre sites, ainsi que les outils statistiques pour évaluer la performance de ces modèles. Toutefois, en dépit des avancées significatives dans cette direction, seules des représentations très simplifiées de la structure protéique ont été utilisées jusqu’à présent. Dans ce contexte, le sujet général de cette thèse est la modélisation de la structure tridimensionnelle des protéines, en tenant compte des limitations pratiques imposées par l’utilisation de méthodes phylogénétiques très gourmandes en temps de calcul. Dans un premier temps, une méthode statistique générale est présentée, visant à optimiser les paramètres d’un potentiel statistique (qui est une pseudo-énergie mesurant la compatibilité séquence-structure). La forme fonctionnelle du potentiel est par la suite raffinée, en augmentant le niveau de détails dans la description structurale sans alourdir les coûts computationnels. Plusieurs éléments structuraux sont explorés : interactions entre pairs de résidus, accessibilité au solvant, conformation de la chaîne principale et flexibilité. Les potentiels sont ensuite inclus dans un modèle d’évolution et leur performance est évaluée en termes d’ajustement statistique à des données réelles, et contrastée avec des modèles d’évolution standards. Finalement, le nouveau modèle structurellement contraint ainsi obtenu est utilisé pour mieux comprendre les relations entre niveau d’expression des gènes et sélection et conservation de leur séquence protéique.