Detailed design of242mAm breeding in pressurized water reactors

There is growing interest in the use of 242mAm as a nuclear fuel. Because of its very high thermal fission cross section and its large number of neutrons released per fission, it can be used for various unique applications, such as space propulsion, medical applications, and compact energy sources. Since the thermal absorption cross section of 242mAm is very high, the best way to obtain 242mAm is by the capture of fast or epithermal neutrons in 241Am. However, fast spectrum reactors are not readily available. In this paper, we explore the possibility of producing 242mAm in existing pressurized water reactors (PWRs) with minimal interference in reactor performance. As suggested in previous studies on the subject, the 242mAm breeding targets are shielded with strong thermal absorbers in order to suppress the thermal neutron flux that causes 242mAm destruction. Since 242mAm enrichment within the Am target mainly depends on the neutron energy distribution, which in turn depends on the Am target thickness and on the neutron filter cutoff energy (thermal absorber type), this unique Am target design was developed. In our study, Cd, Sm, and Gd were considered as thermal neutron filters, as suggested by Cesana et al. The most favorable results were obtained by irradiating Am targets covered either with Gd or Cd. In these cases, up to 8.65% enrichment of 242mAm is obtained after 4.5 yr (three successive PWR fuel cycles) of irradiation. It was also found that significant quantities [up to 1.3 kg/GW (electric)-yr] of 242mAm can be obtained in PWR reactors without notable interference with reactor performance. However, in order to maintain the original fuel cycle length, the enrichment of the driver (UO2) fuel must be increased by ∼1%, raised from the conventional 4.5 to 5.5%, depending on the thermal neutron filter used. The most important reactivity feedback coefficients for fuel assemblies containing the 242mAm breeding targets were evaluated and found to be close to those of a standard PWR. Another product of neutron capture in the 241Am reaction is 238Pu. It was found that in a typical 1000 MW (electric) PWR core with one-third of the fuel assemblies containing 241Am targets, up to 15.1 kg of 238Pu enriched to 80% can be produced per year.

Consideration of reactivity initiated accidents for TRU recycling in LWRs

Response of a PWR core loaded with Combined Non-Fertile and UO2 (CONFU) fuel assemblies to control rod ejection accident was evaluated. A number of core arrangements and TRU fuel compositions were considered and the results were compared with the performance of a reference all-UO2 core. The comparison was based on the results of a simple point kinetics model with thermal reactivity feedbacks and temperature dependant materials properties. The reactivity coefficients and core average kinetics parameters were obtained from the full core 3D neutronic simulations. The results show that application of the CONFU assembly concept causes only minor deviation of fuel performance characteristics in reactivity initiated accidents. This is a consequence of relatively small loadings of TRU in the CONFU assembly and therefore dominating role of conventional UO2 fuel in the neutronic performance of the core.

Fibers with integrated mechanochemical switches: minimalistic design principles derived from fibronectin.

Inspired by molecular mechanisms that cells exploit to sense mechanical forces and convert them into biochemical signals, chemists dream of designing mechanochemical switches integrated into materials. Using the adhesion protein fibronectin, whose multiple repeats essentially display distinct molecular recognition motifs, we derived a computational model to explain how minimalistic designs of repeats translate into the mechanical characteristics of their fibrillar assemblies. The hierarchy of repeat-unfolding within fibrils is controlled not only by their relative mechanical stabilities, as found for single molecules, but also by the strength of cryptic interactions between adjacent molecules that become activated by stretching. The force-induced exposure of cryptic sites furthermore regulates the nonlinearity of stress-strain curves, the strain at which such fibers break, and the refolding kinetics and fraction of misfolded repeats. Gaining such computational insights at the mesoscale is important because translating protein-based concepts into novel polymer designs has proven difficult.

Use of axially graded burnable boron for hot-spot temperature reduction in a pressurized water reactor core

Shortly after the loading of a pressurized water reactor (PWR) core, the axial power distribution in fresh fuel has already attained the characteristic, almost flat shape, typical of burned fuel. At beginning of cycle (BOC), however, the axial distribution is centrally peaked. In assemblies hosting uniform burnable boron rods, this BOC peaking is even more pronounced. A reduction in the axial peaking is today often achieved by shortening the burnable boron rods by some 30 cm at each edge. It is shown that a two-zone grading of the boron rod leads, in a representative PWR cycle, to a reduction of the hot-spot temperature of approximately 70 °C, compared with the nongraded case. However, with a proper three-zone grading of the boron rod, an additional 20 °C may be cut off the hot-spot temperature. Further, with a slightly skewed application of this three-zone grading, an additional 50 °C may be cut off. The representative PWR cycle studied was cycle 11 of the Indian Point 2 station, with a simplification in the number of fuel types and in the burnup distribution. The analysis was based on a complete three-dimensional burnup calculation. The code system was ELCOS, with BOXER as an assembly code for the generation of burnup-dependent cross sections and SILWER as a three-dimensional core code with thermal-hydraulic feedback.

Effects of cooling time on a closed LWR fuel cycle

In this study, the effects of cooling time prior to reprocessing spent LWR fuel has on the reactor physics characteristics of a PWR fully loaded with homogeneously mixed U-Pu or U-TRU oxide (MOX) fuel is examined. A reactor physics analysis was completed using the CASM04e code. A void reactivity feedback coefficient analysis was also completed for an infinite lattice of fresh fuel assemblies. Some useful conclusions can be made regarding the effect that cooling time prior to reprocessing spent LWR fuel has on a closed homogeneous MOX fuel cycle. The computational analysis shows that it is more neutronically efficient to reprocess cooled spent fuel into homogeneous MOX fuel rods earlier rather than later as the fissile fuel content decreases with time. Also, the number of spent fuel rods needed to fabricate one MOX fuel rod increases as cooling time increases. In the case of TRU MOX fuel, with time, there is an economic tradeoff between fuel handling difficulty and higher throughput of fuel to be reprocessed. The void coefficient analysis shows that the void coefficient becomes progressively more restrictive on fuel Pu content with increasing spent fuel cooling time before reprocessing.

Thorium energy futures

The potential for thorium as an alternative or supplement to uranium in fission power generation has long been recognised, and several reactors, of various types, have already operated using thorium-based fuels. Accelerator Driven Subcritical (ADS) systems have benefits and drawbacks when compared to conventional critical thorium reactors, for both solid and molten salt fuels. None of the four options - liquid or solid, with or without an accelerator - can yet be rated as better or worse than the other three, given today's knowledge. We outline the research that will be necessary to lead to an informed choice. Copyright © 2012 by IEEE.

Fabrication and integration of horizontally aligned carbon nanotube C60 films for UV sensors

Carbon nanotubes (CNTs) are promising for microsystems applications, yet few techniques effectively enable integration of CNTs with precise control of placement and alignment of the CNTs at sufficiently high densities necessary for compelling mechanical or electrical performance. This paper explores new methods for scalable integration of dense, horizontally aligned (HA) CNTs with patterned electrodes. Our technique involves the synthesis of vertically aligned (VA) CNTs directly on a conductive underlayer and subsequent mechanical transformation into HA-CNTs, thus making electrical contact between two electrodes. We compare elasto-capillary folding and mechanical rolling as methods for transforming VA-CNTs, which lead to distinctly different HA-CNT morphologies and potentially impact material and device properties. As an example application of this novel CNT morphology, we investigate fabrication of electrically addressable CNT-C60 hybrid thin films that we previously demonstrated as photodetectors. We synthesize these assemblies by crystallizing C60 from dispersion on HA-CNT thin-film scaffoldings. HA-CNTs fabricated by rolling result in relatively low packing density, so C 60 crystals embed inside the HA-CNT matrix during synthesis. On the other hand, C60 crystallization is restricted to near the surface of HA-CNT films made by the elasto-capillary process. © 2013 IEEE.

Biofunctionalization of PET/SiO2 surfaces for single molecule experiments and medical applications

PET/SiO2 layers were chemically modified to maintain immobilization of functional single molecules. GFP molecules provide an ideal system due to their stability and intrinsic fluorescence. GFP in vivo biotinylated within its NH2-terminal region and attached on the substrate via the biotinstreptavidin bond was further investigated with confocal microscopy, atomic force microscopy (AFM) and spectroscopic ellipsometry (SE). AFM revealed monolayered donut-like structures representing assemblies of biotinstreptavidinbiotinGFP immobilized onto PET/SiO2 surfaces via mPEG. In particular, regions with an approximate height of 12 nm, which approaches the molecular dimensions of the above complex given by molecular modeling, could be detected. The dimensions of the donut-like structures suggest a close-to-each-other positioning of the GFP molecules - which, however, retain their functionality, as evidenced by confocal microscopy. © 2011 World Scientific Publishing Company.

Al2O3 : Cr3+ nanotubes synthesized via homogenization precipitation followed by heat treatment

Cr3+-doped NH4Al(OH)(2)CO3 nanotubes, templated by surfactant assemblies, were successfully synthesized via the homogenization precipitation method, and various crystallographic phase Al2O3:Cr3+ nanotubes were also obtained by postannealing at different temperatures. The characteristic R-1, R-2 doublet line transitions of ruby can be observed in the high crystalline alpha-Al2O3 nanotubes calcined at temperatures higher than 1200 degrees C. The results also indicate that the formation mechanism of the tubular nanostructures should result from the self-rolling action of layered compound NH4Al(OH)(2)CO3 under the assistance of the surfactant soft-template. The convenient synthetic procedure, excellent reproducibility, clean reactions, high yield, and fine quality of products in this work make the present route attractive and significant. Aluminum oxide nanotubes with high specific surface area could be used as fabricating nanosized optical devices doped with different elements and stable catalyst supports of metal clusters.

Optical properties and electrical bistability of CdS nanoparticles synthesized in dodecanethiol

We reported the synthesis of CdS semiconductor nanoparticles using a simple one-pot reaction by thermolysis of cadmium acetylacetonate in dodecanethiol. Optical measurements of the as-obtained CdS nanoparticles revealed that their optical properties were closely related to surface effects. Based upon the cocktail of poly (N-vinylcarbazole) (PVK) and CdS nanoparticles, a bistable device was fabricated by a simple solution processing technique. Such a device exhibited a remarkable electrical bistability, which was attributed to the electric field-assisted charge transfer between PVK and the CdS nanoparticles capped by dodecaethiol. The conduction mechanism changed from an injection-controlled current to a bulk-controlled one during switching from OFF-state to ON-state.

固体表面的分子组装体和纳米结构

本文评叙了分子组装体和纳米结构在固体表面的自组装及其应用，并对控制其自组装过程中的分子间作用力和表面力进行了介绍．采用扫描探针显微学结合电化学的方法对自组装膜（SAMs）、仿生膜（biomimetic mebane），金属和聚合物纳米颗粒（nanoparticles）等分子组装体系进行了研究。主要结果如下：(l)我们研究了2-巯基，-3-烷基唾吩（MOT）在金电极表面的自组装行为。测量了MOT膜的电容，结果表面MOT膜能够选择性的透过溶液中的探针物种。交流阻抗和欠电位沉积研究表明湘T膜的覆盖度达99.9%以上。在硫酸溶液中评价了MOT膜的稳定性，MOT膜的电位窗阳极极限为1.2V。次外，我们还研究了一系列有机小分子在MOT膜上的通透行为，实验结果显示于MOT膜的选择性透过能力最密切相关的是探针分子的溶剂化程度，溶剂化程度约高通过能力越差。我们进一步研究呢MOT膜与表面活性剂的相互作用，发现表面活性剂分子能够在MOT膜表面强烈的吸附，并使MOT膜对电极的封闭作用大大地增强。（2）我们在基于MOT的单组分和电活性多组分的自组膜上进一步构筑了杂化:仿生双层膜，并且研究了双层膜的形成对其中电活性物质的氧化还原反应热力学的影响。跟踪了该双层的形成动力学并研究了其界面属性。得到交叉构象的双层膜．研究了重组其中的HRP的电活性以及磷脂酶A2对该膜的水解动力学。证明我们得到的双层膜比基于烷基硫醇的双层膜有更好的稳定性，而且在仿生膜基础研究和生物传感器应用的有很好的应用前景。（3）我们在MOT和C10SH自组膜上利用表面力，憎水力和电泳力协同作用组装了电活性金纳米粒子。用伏安法跟踪了纳米粒子在界面成膜的过程。用扫描探针显微术对表面得到的纳米结构经行了研究。结果表面这些弱相互作用力协同作用可形成二维纳米结构的表面。(4)我们在单晶Au（111）表面制备了分子导线和长链烷基硫醇的混合自组装膜。以该自组装膜为模板，我们在其表面选择性的生长了聚苯胺纳米结构，这些纳米结构可以作为为阵列电极，而且具有开关特性；同时这些结构为研究分子导线的导电性质提供了一个理想平台。

Fabrication of silicon-on-reflector for Si-based resonant-cavity-enhanced photodetectors

A novel silicon-on-reflector substrate for Si-based resonant-cavity-enhanced photodetectors has been fabricated by using Si-based sol-gel and smart-cut techniques. The Si/SiO2 Bragg reflector is controlled in situ by electron beam evaporation and the thickness can be adjusted to get high reflectivity. The reflectance spectra of the silicon-on-reflector substrate with five pairs of Si/SiO2 reflector have been measured and simulated by transfer matrix model. The reflectivity at operating wavelength is close to 100%. Based on the silicon-on-reflector substrate, SiGe/Si multiple quantum wells resonant-cavity-enhanced photodetectors for 1.3 mu m wavelength have been designed and simulated. Ten-fold enhancement of the quantum efficiency of resonant-cavity-enhanced photodetectors compared with conventional photodetectors is predicted.

苯乙酮、氨甲酸酯参与的直接Mannich反应

Mannich反应是有机化学中最重要的碳-碳键形成反应，其产物是合成手性胺的通用中间体。间接Mannich反应使用不稳定的预制烯醇等当体，以未修饰的酮为给体的直接方法将增强Mannich反应的效率。针对低活性苯乙酮、氨甲酸酯参与的直接Mannich反应，研究工作将更具挑战性。 在前期实验中，我们发现Lewis酸-NbCl5可高效催化苯乙酮、芳香醛、芳香胺三组分直接Mannich反应，反应在环境温度下进行，高收率获得Mannich碱。这是以苯乙酮参与的Mannich反应中，实现催化量Lewis酸催化的首次报道。该方法高效且操作简单。但就底物而言，对易去保护、低活性的氨甲酸酯类底物收率较低。我们设想Brønst酸可解决此类底物问题。令人高兴的是，杂多酸可高效催化芳香酮、芳香醛、氨甲酸酯三组分直接Mannich反应，反应在环境温度下进行，高收率获得N-保护的β-氨基酮。该方法底物范围广泛，普适性强且催化剂便宜。 基于杂多酸在苯乙酮、氨甲酸酯为底物直接Mannich反应中的高效性，我们设想杂多酸与功能化的手性有机小分子-手性伯胺组装可解决催化剂回收问题，同时实现不对称催化。实验结果表明，非共价键固载手性伯胺不能有效催化苯乙酮为底物的直接Mannich反应，无论是对映选择性还是收率均较低。随后，我们以丙二酸酯及α-氨基砜为底物，以增强底物活性，同时绕开亚胺的不稳定性。辛可宁伯胺以氢键双活化底物，有效催化原位产生氨甲酸酯类亚胺与丙二酸酯的Mannich反应，高收率获得Mannich碱，ee值中等。 我们采用逐步解决问题的策略解决Mannich反应中的部分问题并在Lewis酸催化、Brønst酸催化、非共价键固载手性伯胺催化及手性伯胺氢键催化的直接Mannich反应中做出了有益探索。 The Mannich reactions are among the most fundamental carbon-carbon bond forming reactions in organic chemistry, and the reaction products are versatile intermediates in the synthesis of chiral amines. The indirect Mannich reaction uses preformed enolate equivalents. However the preformed enolates are unstable. Thus, a direct methodology based on unmodified ketone donors would enhance the efficiency of the Mannich reaction. Especially researches for the directed Mannich reactions of acetophenone, carbamate, which own lower activities, will be more challengeable. In the initial experiments, we found an efficient Lewis acid-NbCl5 which could catalyze three-component Mannich-type reaction of acetophenone, aromatic aldehydes and aromatic amines at ambient temperature in high yields. This is the first report that use catalytic amount of Lewis acid in the Mannich reactions of .acetophenone. The method reported is not only simple to operate but also efficient. However, as far as amines are concerned, the substrates of carbamates which can be deprotected more easily and less reactive than amines give low yields. We envisaged that Brønsted acid would resolve this problem. Pleasingly, heteropoly acids (HPA) efficiently catalyzed one-pot three-component Mannich reactions of aryl aldehydes, aryl ketones, and carbamates at ambient temperature and afforded the corresponding N-protected β-amino ketones in good to excellent yields. This method provides a novel and improved modification of three-component Mannich reactions in terms of a wide scope of aldehydes, ketones and carbamates, economic viability. Based on the high efficiency of heteropoly acids in the Mannich reaction of acetophenone and carbamates, we envisaged that if HPA were combined with functionalized chiral organocatalysts–chiral primary amines the assemblies may be able to act as recoverable asymmetric organocatalysts. The results of exprimentals showed that noncovalently supported heterogeneous chiral primary amine couldn’t effectively catalyze the Mannich reactions which own two the substrate of acetophenone regardless of enantioselectivity and yield. Then, we employed malonates and α-amido sulfones as substrates to enhance reactivity of substrates and circumvent the instability of imines. A moderately enantioselective and highly yield Mannich reaction with in situ generation of carbamate-protected imines from stable α-amido sulfones catalyzed by cinchonine primary amine catalyst was developed. It is noteworthy that cinchonine primary amine can dual activate substrates through H-bond activation and thus promote the reaction. We applied step-by-step-strategy to resolve some problems in the Mannich reactions and did some instructive explorations in Lewis acid catalysis, Brønst acid catalysis, noncovalently supported heterogeneous chiral primary amine catalysis and chiral primary amine as hydrogen-bond catalysis.

Fabrication of a miniature twin-fuel-cell on silicon wafer

The fabrication and performance evaluation of a miniature twin-fuel-cell on silicon wafers are presented in this paper. The miniature twin-fuel-cell was fabricated in series using two membrane-electrode-assemblies sandwiched between two silicon substrates in which electric current, reactant, and product flow. The novel structure of the miniature twin-fuel-cell is that the electricity interconnect from the cathode of one cell to the anode of another cell is made on the same plane. The interconnect was fabricated by sputtering a layer of copper over a layer of gold on the top of the silicon wafer. Silicon dioxide was deposited on the silicon wafer adjacent to the copper layer to prevent short-circuiting between the twin cells. The feed holes and channels in the silicon wafers were prepared by anisotropic silicon etching from the back and front of the wafer with silicon dioxide acting as intrinsic etch-stop layer. Operating on dry H-2/O-2 at 25 degreesC and atmospheric pressure, the measured peak power density was 190.4 mW/cm(2) at 270 mA/cm(2) for the miniature twin-fuel-cell using a Nafion 112 membrane. Based on the polarization curves of the twin-fuel-cell and the two single cells, the interconnect resistance between the twin cells was calculated to be in the range from 0.0113 Omega (at 10 mA/cm(2)) to 0.0150 Omega (at 300 mA/cm(2)), which is relatively low. (C) 2003 Elsevier Science Ltd. All rights reserved.