The Influence of Process Conditions on the Deresination Efficiency in Mechanical Pulp Washing

The aim of this thesis was to produce information for the estimation of the flow balance of wood resin in mechanical pulping and to demonstrate the possibilities for improving the efficiency of deresination in practice. It was observed that chemical changes in wood resin take place only during peroxide bleaching, a significant amount of water dispersed wood resin is retained in the pulp mat during dewatering and the amount of wood resin in the solid phase of the process filtrates is very small. On the basis of this information there exist three parameters related to behaviour of wood resin that determine the flow balance in the process: 1. The liberation of wood resin to the pulp water phase 2. Theretention of water dispersed wood resin in dewatering 3. The proportion of wood resin degraded in the peroxide bleaching The effect of different factors on these parameters was evaluated with the help of laboratory studies and a literature survey. Also, information related to the values of these parameters in existing processes was obtained in mill measurements. With the help of this information, it was possible to evaluate the deresination efficiency and the effect of different factors on this efficiency in a pulping plant that produced low-freeness mechanical pulp. This evaluation showed that the wood resin content of mechanical pulp can be significantly decreased if there exists, in the process, a peroxide bleaching and subsequent washing stage. In the case of an optimal process configuration, as high as a 85 percent deresination efficiency seems to be possible with a water usage level of 8 m3/o.d.t.

A novel approachfor assessing the fatigue strength of ultrasonic impact treated welded structures.

It is commonly observed that complex fabricated structures subject tofatigue loading fail at the welded joints. Some problems can be corrected by proper detail design but fatigue performance can also be improved using post-weld improvement methods. In general, improvement methods can be divided into two main groups: weld geometry modification methods and residual stress modification methods. The former remove weld toe defects and/or reduce the stress concentrationwhile the latter introduce compressive stress fields in the area where fatigue cracks are likely to initiate. Ultrasonic impact treatment (UIT) is a novel post-weld treatment method that influences both the residual stress distribution andimproves the local geometry of the weld. The structural fatigue strength of non-load carrying attachments in the as-welded condition has been experimentally compared to the structural fatigue strength of ultrasonic impact treated welds. Longitudinal attachment specimens made of two thicknesses of steel S355 J0 have been tested for determining the efficiency of ultrasonic impacttreatment. Treated welds were found to have about 50% greater structural fatigue strength, when the slope of the S-N-curve is three. High mean stress fatigue testing based on the Ohta-method decreased the degree of weld improvement only 19%. This indicated that the method could be also applied for large fabricated structures operating under high reactive residual stresses equilibrated within the volume of the structure. The thickness of specimens has no significant effect tothe structural fatigue strength. The fatigue class difference between 5 mm and 8 mm specimen was only 8%. It was hypothesized that the UIT method added a significant crack initiation period to the total fatigue life of the welded joints. Crack initiation life was estimated by a local strain approach. Material parameters were defined using a modified Uniform Material Law developed in Germany. Finite element analysis and X-ray diffraction were used to define, respectively, the stress concentration and mean stress. The theoretical fatigue life was found to have good accuracy comparing to experimental fatigue tests.The predictive behaviour of the local strain approach combined with the uniformmaterial law was excellent for the joint types and conditions studied in this work.

Dynamics of Appropriability - Finding a Balance between Efficiency and Strength in the Appropriability Regime

Building and sustaining competitive advantage through the creation of market imperfections is challenging in a constantly changing business environment - particularly since the sources of such advantages are increasingly knowledge-based. Facilitated by improved networks and communication, knowledge spills over to competitors more easily than before,thus creating an appropriability problem: the inability of an innovating firm to utilize its innovations commercially. Consequently, as the importance of intellectual assets increases, their protection also calls for new approaches. Companies have various means of protection at their disposal, and by taking advantage of them they can make intangibles more non-transferable and prevent, or at leastdelay, imitation of their most crucial intellectual assets. However, creating barriers against imitation has another side to it, and the transfer of knowledge in situations requiring knowledge sharing may be unintentionally obstructed. Theaim of this thesis is to increase understanding of how firms can balance knowledge protection and sharing so as to benefit most from their knowledge assets. Thus, knowledge protection is approached through an examination of the appropriability regime of a firm, i.e., the combination of available and effective means ofprotecting innovations, their profitability, and the increased rents due to R&D. A further aim is to provide a broader understanding of the formation and structure of the appropriability regime. The study consists of two parts. The first part introduces the research topic and the overall results of the study, and the second part consists of six complementary research publications covering various appropriability issues. The thesis contributes to the existing literature in several ways. Although there is a wide range of prior research on appropriability issues, a lot of it is restricted either to the study of individual appropriability mechanisms, or to comparing certain features of them. These approaches are combined, and the relevant theoretical concepts are clarified and developed. In addition, the thesis provides empirical evidence of the formation of the appropriability regime, which is consequently presented as an adaptive process. Thus, a framework is provided that better corresponds to the complex reality of the current business environment.

Bond strength tests of dental adhesive systems and their correlation with clinical results : a meta-analysis

OBJECTIVE: To evaluate the variability of bond strength test results of adhesive systems (AS) and to correlate the results with clinical parameters of clinical studies investigating cervical restorations. MATERIALS AND METHODS: Regarding the clinical studies, the internal database which had previously been used for a meta-analysis on cervical restorations was updated with clinical studies published between 2008 and 2012 by searching the PubMed and SCOPUS databases. PubMed and the International Association for Dental Research abstracts online were searched for laboratory studies on microtensile, macrotensile and macroshear bond strength tests. The inclusion criteria were (1) dentin, (2) testing of at least four adhesive systems, (3) same diameter of composite and (4) 24h of water storage prior to testing. The clinical outcome variables were retention loss, marginal discoloration, detectable margins, and a clinical index comprising the three parameters by weighing them. Linear mixed models which included a random study effect were calculated for both, the laboratory and the clinical studies. The variability was assessed by calculating a ratio of variances, dividing the variance among the estimated bonding effects obtained in the linear mixed models by the sum of all variance components estimated in these models. RESULTS: Thirty-two laboratory studies fulfilled the inclusion criteria comprising 183 experiments. Of those, 86 used the microtensile test evaluating 22 adhesive systems (AS). Twenty-seven used the macrotensile test with 17 AS, and 70 used the macroshear test with 24 AS. For 28 AS the results from clinical studies were available. Microtensile and macrotensile (Spearman rho=0.66, p=0.007) were moderately correlated and also microtensile and macroshear (Spearman rho=0.51, p=0.03) but not macroshear and macrotensile (Spearman rho=0.34, p=0.22). The effect of the adhesive system was significant for microtensile and macroshear (p<0.001) but not for macrotensile. The effect of the adhesive system could explain 36% of the variability of the microtensile test, 27% of the macrotensile and 33% of the macroshear test. For the clinical trials, about 49% of the variability of retained restorations could be explained by the adhesive system. With respect to the correlation between bond strength tests and clinical parameters, only a moderate correlation between micro- and macrotensile test results and marginal discoloration was demonstrated. However, no correlation between these tests and a retention loss or marginal integrity was shown. The correlation improved when more studies were included compared to assessing only one study. SIGNIFICANCE: The high variability of bond strength test results highlights the need to establish individual acceptance levels for a given test institute. The weak correlation of bond-strength test results with clinical parameters leads to the conclusion that one should not rely solely on bond strength tests to predict the clinical performance of an adhesive system but one should conduct other laboratory tests like tests on the marginal adaptation of fillings in extracted teeth and the retention loss of restorations in non-retentive cavities after artificial aging.

Determination of thermal diffusivity in papaya pulp as a function of maturation stage

In order to determine the penetration of the thermal wave in the papaya fruit pulp (Carica papaya L.), cv. Golden, thermal diffusivity of the pulp was obtained measuring temperature at four different depths. Measurements were carried out initially with the fruit on the first stage of maturity. The changes of the thermal diffusivity were expressed as a function of ripening. A temporal decrease of the thermal diffusivity was observed. Chemical (pH, soluble solids and total titratable acidity) and physical (pulp firmness) properties were measured as well and the results were compared to the thermal diffusivity change.

Power spectral changes of the superimposed M wave during isometric voluntary contractions of increasing strength.

INTRODUCTION: We examined the power spectral changes of the compound muscle action potential (M wave) evoked during isometric contractions of increasing strength. METHODS: Surface electromyography (sEMG) of the vastus lateralis and medialis was recorded from 20 volunteers who performed 4-s step-wise isometric contractions of different intensities. A maximal M wave was elicited by a single stimulus to the femoral nerve and superimposed on the voluntary contractions. The spectral characteristics (Fmean and Fmedian) of sEMG and M-wave signals were calculated. RESULTS: M-wave spectral indicators increased systematically with contraction intensity up to 60% MVC and then leveled off at higher forces. Over the 10-60% MVC range, the increase in spectral indicators was 3 times higher for M waves (36%) than for sEMG (12%). CONCLUSIONS: The consistent increase in M-wave spectral characteristics with force is due to the fact that the number of motor units recruited by the superimposed supramaximal stimulus is approximately stable.

Enzymatic technology to improve oil extraction from Caryocar brasiliense camb. (Pequi) Pulp.

The present study aims to compare yield and quality of pequi pulp oil when applying two distinct processes: in the first, pulp drying in a tray dryer at 60ºC was combined with enzymatic treatment and pressing to oil extraction; in the second, a simple process was carried out by combining sun-drying pulp and pressing. In this study, raw pequi fruits were collected in Mato Grosso State, Brazil. The fruits were autoclaved at 121ºC and stored under refrigeration. An enzymatic extract with pectinase and CMCase activities was used for hydrolysis of pequi pulp, prior to oil extraction. The oil extractions were carried out by hydraulic pressing, with or without enzymatic incubation. The oil content in the pequi pulp (45% w/w) and the physicochemical characteristic of the oil was determined according to standard analytical methods. Free fatty acids, peroxide values, iodine and saponification indices were respectively 1.46 mgKOH/g, 2.98 meq/kg, 49.13 and 189.40. The acidity and peroxide values were lower than the obtained values in commercial oil samples, respectively 2.48 mgKOH/g and 5.22 meq/kg. Aqueous extraction has presented lower efficiency and higher oxidation of unsaturated fatty acids. On the other hand, pequi pulp pressing at room temperature has produced better quality oil. However its efficiency is still smaller than the combined enzymatic treatment and pressing process. This combined process promotes cellular wall hydrolysis and pulp viscosity reduction, contributing to at least 20% of oil yield increase by pressing.

Anaerobic treatment of deinking pulp plant effluents

Anaerobic treatment as a first biological stage in wastewater treatment is nowadays a well-established technology in recycled paper processing mills using closed water circuits. Today further developed high-rate processes and especially high-tower reactors are also able to handle lower organic loads and become therefore feasible for deinking pulp plant effluents. The interest in the anaerobic method is based on a positive energy balance in form of biogas production and low biomass yield from the process. The anaerobic treatment method was researched and its suitability for the deinking pulp plant effluents was tested experimentally at Stora Enso Maxau mill. In the theory, the deinking pulp process is introduced and the effluents from the deinking process are characterized. The anaerobic treatment is brought up in depth in terms of its use for the deinking effluents, and different kind of reactor types are presented. In addition, other wastewater treatment methods are shortly introduced with the focus on tertiary treatment. Static biodegradability tests were carried out for the wastewaters both anaerobically and aerobically. Based on the results, the deinking effluents can be degraded anaerobically, and inhibition to the methanogenic bacteria was not noticed. In the aerobic static test a good performance of the existing wastewater treatment plant at Maxau mill was proved. Later on pilot trials with sequential anaerobic-aerobic treatment were carried out for the deinking effluents. The anaerobic reactor used was a so called internal circulation reactor. The results confirmed that the combination of the anaerobic treatment and the aerobic activated sludge process is a suitable method for deinking wastewaters with a COD reduction as good as with a two stage aerobic method. When combined with the outstanding quality of the produced biogas and the cost savings acquired from the lower sludge production, the anaerobic treatment was found to be an especially favorable treatment method.

An ethanol-based process to simultaneously extract and fractionate carotenoids from Mauritia flexuosa L. Pulp

Mauritia vinifera (buriti) is a palm tree that grows wild in different areas of Brazil, particularly in the Amazonian region. The buriti oil is rich in carotenoids, especially in β-carotene. The growing interest in other natural sources of β-carotene has stimulated the industrial use of buriti as a raw material for pulp oil extraction. Most processes are based on the conventional technologies, involving drying and pressing the pulp for oil recovery and further separation of carotenoids in a liquid phase using organics solvents. In the present work, the ethanol-based process was evaluated for simultaneous carotenoids recovering and fractionating from buriti pulp. The raw material and ethanol, 1:4 ratio, were placed in an erlenmeyer flask and maintained at 30rpm for 1 hour in a temperature-controlled bath at 65ºC. The mixture was filtered under vacuum and cooling at 10ºC to allow for the separation of the solvent in two phases. Carotenoids composition, determined by HPLC, has indicated a β-carotene concentration about 12 times greater in the lower phase than in the upper phase. The profile of the carotenoids in the denser phase is quite similar to that of raw buriti oil, and the concentration of total carotenoids is 40% higher than that of the original raw oil, making the ethanol-based process particularly attractive for industrial applications.

Papaya pulp gelling: is it premature ripening or problems of water accumulation in the apoplast?

Gelled aspect in papaya fruit is typically confused with premature ripening. This research reports the characterization of this physiological disorder in the pulp of papaya fruit by measuring electrolyte leakage, Pi content, lipid peroxidation, pulp firmness, mineral contents (Ca, Mg and K - in pulp and seed tissues), and histological analysis of pulp tissue. The results showed that the gelled aspect of the papaya fruit pulp is not associated with tissue premature ripening. Data indicate a reduction of the vacuole water intake as the principal cause of the loss of cellular turgor; while the waterlogged aspect of the tissue may be due to water accumulation in the apoplast.

Elastomeerien kesto viherlipeäkäsittelyissä

Työssä on tutkittu eri kumilaatujen soveltuvuutta viherlipeäympäristöön laboratoriomittausten avulla. Kumia tultaisiin käyttämään viherlipeälinjan letkuventtiilissä. Suomalaisista sellutehtaista saaduista viherlipeänäytteistä mitattiin alkali- ja vierasainepitoisuudet. Kumitestauksissa viherlipeässä pyrittiin selvittämään kumien kesto prosessiolosuhteita vastaavissa olosuhteissa. Kumit asetettiin kuumaan viherlipeään jännitettynä ja pidettiin siinä kolme vuorokautta. Kumista tutkittavia ominaisuuksia olivat kumin massan muutos, kovuus, vetolujuus sekä murtovenymä. Kolmen vuorokauden testien tulosten perusteella valittiin kolme kumilaatua tuhannen tunnin kestotestiin, joissa seurattiin kumin massan käyttäytymistä sekä kumin pitkäaikaisen altistamisen viherlipeässä vaikutusta lujuusominaisuuksiin. Kokeissa havaittiin osan testatuista kumeista sitovan viherlipeää itseensä, mikä aiheuttaisi viherlipeän pääsyn letkun vahvikkeisiin ja aiheuttaisi letkun hajoamisen. Osa kumeista kului kemiallisesti, mikä taas aiheuttaisi letkun rasitustilanteissa repeämiä letkun pinnassa ja lopulta letkun hajoamisen. Kuitenkin suuressa osassa testatuissa kumimateriaaleissa ei ollut suuria massanmuutoksia. Tällöin lujuusmittaukset kertoivat muilta osin kumin kestosta. Muutamilla kumeilla massanmuutokset olivat alhaisia, mutta lujuusarvot olivat romahtaneet. Kuitenkin laboratoriomittausten tulosten perusteella pystyttiin löytämään kumimateriaali, joka kestäisi paremmin viherlipeäprosessissa kuin teollisuudessa käytössä ollut kumimateriaali. Kuitenkin lopullinen varmuus tästä voidaan saada teollisuudessa tehtyjen testausten avulla.

Selluradan leijutus ja hallinta ilmakuivaimessa

Diplomityön tavoitteena oli tutkia selluradan leijutusta sekä hallintaa kapealla ja täysleveällä selluradalla ilmakuivaimessa. Työn sisältö on jaettu neljään osaan teoriaan, numeeriseen virtauslaskentaan, kokeelliseen osuuteen ja johtopäätöksiin. Työn alussa kiinnitettiin huomiota ilmakuivaimen ja selluradan rakenteeseen, selluradan lujuusominaisuuksiin ja niiden testaamiseen laboratorio-oloissa. Teoria osuudessa tarkasteltiin selluradan leijutusteoriaa ja siihen liittyvää virtaustekniikkaa. Leijutusta kuvattiin mekaniikasta tutun vapaakappalekuvan muodossa. Vapaakappalekuva auttaa ymmärtämään sellurataan vaikuttavia voimia ja niiden aiheuttajia. Numeerisessa virtauslaskennassa rakennettiin Fluent -virtauslaskentamalli. Malli kuvaa leijutussuuttimen alusta 0,2 metrin pituista pätkää. Laskennassa simuloitiin selluradan lei-jutusta 2, 5 ja 7 mm etäisyyksillä. Tuloksia tarkasteltiin paine- ja nopeusjakaumien muodossa. Kokeellisessa osuudessa tehtiin mittauksia yksittäisellä ylä- ja alasuuttimella sekä suutinpaketilla. Yksittäisistä suuttimista mitattiin ilmasuihkujen ulostulokulmaa, suuttimensisäistä painejakaumaa ja selluradan pintaan vaikuttavaa staattista painetta suuttimen pituuden funktiona. Suutinpaketilla tutkittiin ilmasuihkujen ja tasomaisen levyn välistä vuorovaikutusta. Ylä- ja alasuuttimen välissä leijutettiin levyä, josta mitattiin ilmasuihkujen aiheuttama z-suuntainen voima ja leijutuskorkeus. Työn lopussa arvioitiin teorian, numeerisen virtauslaskennan ja kokeellisen osuuden tuloksia. Näiden pohjalta tehtiin teknisiä parannusehdotuksia ilmakuivaimen toiminnan tehostamiseksi ja selluradan hallinnan parantamiseksi kapealla ja täysleveällä selluradalla.

LWC-SYVÄPAINOHIOKKEEN LAADUN OPTIMOINTI

Työn tavoitteena oli hiokkeen laatua optimoimalla löytää keinoja pohjapaperin opasiteetin parantamiseksi. Tehtaalla oli havaittu hiokkeen palstautumislujuuden pudonneen ja pian tämän jälkeen oli paperikoneella nostettu sellun jauhatustehoa mikä puolestaan vaikuttaa negatiivisesti pohjapaperin opasiteettiin. Päähuomio hiokkeen laadun optimoinnissa keskitettiin tästä syystä palstautumislujuuden tason nostamiseen. Kirjallisuuden mukaan tärkein hiokkeen palstautumislujuuteen ja myös opasiteettiin vaikuttava tekijä on massan hienoaines. Hiokkeen hienoainespitoisuuden lisäämistä tutkittiin tässä työssä seuraavalla kolmella tavalla: rejektijauhatuksen optimointi, kivenalusmassan CSF-tason alentaminen ja jälkijauhatustehon lisääminen. Työn toisena tavoitteena oli varmistaa rejektilinjan kapasiteetin riittävyys, erityisesti rejektilajitin 6:n osalta. Taustana tälle tarkastelulle oli mahdollisen lisälajittimen investointitarve RL 6:n rinnalle. Rejektijauhatuksen optimoinnissa tutkittiin jauhatustehon, eri terämallien ja kahden rinnakkaisen rejektijauhimen (yhden sijasta) vaikutusta jauhetun rejektimassan ominaisuuksiin. Pidättävillä rejektijauhimen terillä jauhetusta massasta tuli pitkäkuituisempaa kuin referenssiterillä, joissa staattori oli pumppaava ja roottori pidättävä. Mutta vaikka pidättävillä terillä jauhettu massa oli pitkäkuituisempaa ja sisälsi vähemmän hienoainetta oli sen palstautumislujuus samaa luokkaa kuin referenssiterillä jauhetun massan. Kahden rinnakkaisen jauhimen ajomallilla saatiin laadultaan kaikein heikointa massaa. Kaikissa koeajoissa saatiin rejektimassan palstautumislujuutta parannettua jauhatustehoa lisäämällä. Kivenalusmassan CSF-tasoa alentamalla ei valmiin annosteluhiokkeen palstautumislujuus alentunut vaikka hiokkeen hienoainespitoisuus kasvoi hieman. Mutta vaikka hiokkeen palstautumislujuus ei kasvanutkaan niin koejaksolla, joka oli pituudeltaan hieman yli kuukauden, pohjapaperin opasiteetti kuitenkin parani hieman ja sellun jauhatustehoa voitiin paperikoneella pudottaa hieman. Palstautumislujuuskartoituksen, jossa otettiin näytteitä hiomon eri prosessivaiheista, mukaan jälkijauhatus oli yksittäisenä prosessivaiheena eniten hiokkeen palstautumislujuuteen vaikuttava prosessivaihe. Jälkijauhatuskoeajosta saatiinkiin parhaimmat tulokset hienoainespitoisuuden ja palstautumislujuuden nousun suhteen. Rejektilajittelun massarejektisuhteiden määritysten ja rejektilajitin 6:n kapasiteettikokeen mukaan rejektilajittelu toimii nykyisellä tuotantomäärällä halutunlaisesti ja rejektilajitin 6:n osalta tuotantoa on vielä varaa nostaakin.