Optimization of energy in a pulp mill

This study presents examination of ways to increase power generation in pulp mills. The main purpose was to identify and verify the best ways of power generation growth. The literature part of this study presented operation of energy pulp mill departments, energy consumption and generation by the recovery and power boilers. The second chapter of this part described the main directions for increase of electricity generation rise of black liquor dry solid content, increase of main steam parameters, flue gas heat recovery technologies, feed water and combustion air preheating. The third chapter of the literature part presented possible technical, environment and corrosion risks appeared from described alternatives. In the experimental part of this study, calculations and results of possible models with alternatives was presented. The possible combinations of alternatives were generated in 44 `models of energy pulp mill. The target of this part was define extra electricity generation after alternatives using and estimate profitability of generated models. The calculations were made by computer programme PROSIM. In the conclusions, the results were estimated on the basis of extra electricity generation and equipment design data of models. The profitability of cases was verified by their payback periods and additional incomes.

Kierrätyspolttoaineiden käyttö leijukerrospoltossa vetykaasun kanssa

Tämä diplomityö on tehty Leppäkosken Energia Oy:n ja Kemira Chemicals Oy:n yhteisyritys FC Energia Oy:lle. FC Energia Oy suunnittelee rakentaa uutta bio-vetyvoimalaitosta Sastamalaan. Voimalaitoksella tuotettaisiin Kemira Chemicals Oy:n ylijäämävedystä ja biopolttoaineista sähköä, kaukolämpöä ja prosessihöyryä. Ympäristölupaa on haettu hakkeen, turpeen ja kierrätyspuun poltolle vetykaasun kanssa. Voimalaitoksen kattilan toiminta perustuu kuplivaan leijukerrostekniikkaan. Diplomityössä selvitettiin, mitä muutoksia kierrätyspolttoaineiden käyttö vaatii leijukerrospoltossa verrattuna hakkeen ja turpeen polttoon. Kierrätyspolttoaineena käytetään hyvälaatuista kierrätyspuuta. Kierrätyspuun käytössä sovelletaan jätteenpoltto-asetusta. Jätteenpolttoasetus määrää tiukemmat päästöjen raja-arvot rinnakkaispoltolle kuin hakkeen ja turpeen poltolle sekä jatkuvatoimiset savukaasujen mittauslaitteet. Rinnakkaispolton hiukkasmaisten päästöjen tiukempi raja-arvo vaatii tehokkaamman sähkösuodattimen. Lisäksi kierrätyspuuta käytettäessä tulistimen materiaaliin tulee olla kestävämpää, mikä aiheuttaa huomattavan lisäinvestoinnin. Työn päätavoitteena oli selvittää, onko kierrätyspuun käyttö taloudellisesti kannattavaa. Oletetulla kierrätyspuun hinnalla 10 €/MWh kierrätyspuuta polttavan voimalaitoksen takaisinmaksuaika on sama kuin haketta polttavan laitoksen ja vuoden lyhyempi kuin turvetta polttavan laitoksen. Tulokseksi saatiin, että rinnakkaispoltto käyttö on taloudellisesti kannattavaa hakkeenpolttoon nähden jos kierrätyspuun hinta on alle 11,2 €/MWh. Kierrätyspuun polttoon liittyy toiminnallinen riski, koska vastaavanlaisia rinnakkaispolttolaitoksia ei ole aiemmin rakennettu.

Governmental Measures to Enhance the Finnish Innovation System to Respond to the Challenge of Mitigating Climate Change

Climate innovations, that cover both technological applications and process and service innovations, play a key role in climate change mitigation. The purpose of this study was to examine how the Finnish innovation system could be enhanced with governmental measures so that the diffusion of climate innovations could be speeded up. During the study, it became evident that the governmental measures need to support the whole innovation chain, which comprises of research, development, demonstration and deployment. Only this can lead to the successful birth and diffusion of low carbon innovations. The study found that the strengths of the Finnish innovation system are research and development, and the current national innovation policies strongly support these activities. However, these have been emphasised at the expense of the demonstration and deployment. Consequently, the biggest bottlenecks in the Finnish innovation landscape are the lack of pilot and demonstration projects and slow commercialisation, thus the high price of the innovation. To meet with the challenge, the government should firstly promote strict greenhouse gas emission reduction targets. This would boost up the innovation activities, which would also lower the prices of the innovations. To speed up the commercialisation process, measures that stimulate the domestic market, such as feed-in-tariffs and public procurements, are needed. Special attention should also be paid to the measures that could shift the traditional closed innovation chain towards open innovation. This means that the product development should involve experts from several fields such as the user and marketing experts to speed up the commercialisation. In addition, efficient innovation co-operation between both private and public sector is essential. Finally, as the domestic resources are not adequate for producing all the innovations needed, the domestic innovation activities should be focused on a few sectors, and at the same time promote efficient import policies.

Technological and business challenges of smart grids

Growing recognition of the electricity grid modernization to enable new electricity generation and consumption schemes has found articulation in the vision of the Smart Grid platform. The essence of this vision is an autonomous network with two-way electricity power flows and extensive real-time information between the generation nodes, various electricity-dependent appliances and all points in-between. Three major components of the Smart Grids are distributed intelligence, communication technologies, and automated control systems. The aim of this thesis is to recognize the challenges that Smart Grids are facing, while extinguishing the main driving factors for their introduction. The scope of the thesis also covers possible place of electricity Aggregator Company in the current and future electricity markets. Basic functions of an aggregator and possible revenue sources along with demand response feasibility calculations are reviewed within this thesis.

Ancillary services market and potential profit for generators in Russia

Reformation of electricity markets has initiated creation of ancillary services markets all over the world. The Russian electricity market reform is in transition period, that is why the problem of ancillary services market has just arisen. Since the model of market rules was created, ancillary services market became a topical question for generating companies. This master’s thesis is focused on the describing the possible ancillary services around the world and in Russia specifically. Moreover, the physical interpretation of ancillary services is defined. In addition, possibility of generation company to participate in the ancillary services market was considered. Calculations were made for primary frequency regulation service, where necessary level of price bids and payback period were evaluated.

Phase voltage control and filtering in a converter-fed single-phase customer-end system of the LVDC distribution network

In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.

Liiketoimintamalli teollisuuden ylijäämälämmön hyödyntämisestä kaukolämpöverkoissa

Tässä työssä tarkastellaan teollisuuden ylijäämälämmön hyödyntämistä kaukolämpöverkoissa liiketoimintamallin näkökulmasta. Työn tilaaja on YIT Teollisuus Oy, joka haluaa osaltaan olla mukana ratkaisemassa ilmastonmuutoksesta ja hiilidioksidipäästöjen vähentämistarpeista aiheutuvia yhteiskunnan kehitystarpeita. Energiatehokkuuden parantaminen on yksi nopeimmista keinoista vähentää päästöjä. Teollisuuden energiatehokkuutta voidaan parantaa ottamalla talteen sähköntuotannossa ja tuotantoprosesseissa syntyvää ylijäämälämpöä. Aikaisempien tutkimusten perusteella tiedetään, että Suomessa syntyy vuosittain noin 4–6 TWh ylijäämälämpöä, joka voitaisiin hyödyntää jo olemassa olevien kaukolämpöverkkojen välityksellä rakennusten lämmittämiseen. Kuitenkin vuonna 2008 teollisuus myi ylijäämälämpöä kaukolämpöverkkoihin yhteensä vain 770 GWh, mikä vastaa noin 2,5 prosenttia kokonaiskaukolämmön tarpeesta. Tämän työn tuloksena syntyi liiketoimintamalli, joka esittelee ne palvelut, jotka YIT tuottaa asiakkailleen tilanteissa, joissa teollisuudessa syntyvää ylijäämälämpöä hyödynnetään kaukolämpöverkoissa. Jotta liiketoimintamalli toimisi käytännössä, on siitä oltava hyötyä kaikille osapuolille. Asiakkaan on siis voitava kattaa palvelusta ja sen rahoituksesta syntyvät kustannukset myydyn ylijäämälämmön tuotolla (teollisuuslaitos) tai säästyneistä energian hankintakustannuksista (kaukolämpöyhtiö). Eniten ylijäämälämmön käytöstä voivat hyötyä kaukolämpöyhtiöt, joiden tuotannosta korkeintaan pieni osa tulee yhteistuotannosta ja joilla uusiutuvien energialähteiden osuus on vähäinen. Lisäksi kaukolämpöverkon koon vuotuisena kulutuksena mitattuna on oltava riittävän suuri ja kaukolämmön hinnan suhteellisen korkea. Myös alueen ennustettu väestönkasvu ja uudet suunnitteilla olevat asuinalueet saattavat parantaa ylijäämälämmön hyödyntämisen houkuttelevuutta. YIT:n näkökulmasta ylijäämälämmön talteenottoprojektit ovat hyvä lisä sen nykyiseen palvelutarjontaan. Myös yhteiskunnallisella tasolla aihe on merkittävä. Vaikka nykytietämyksen mukaan energian käytön tehostaminen ja päästöttömän tuotannon lisääminen ovat molemmat yhtä merkittäviä keinoja ilmastotavoitteiden saavuttamisen kannalta, panostetaan Suomessa tällä hetkellä lähinnä tuotannon tukemiseen. Lähivuosien poliittiset ratkaisut vaikuttavatkin vahvasti siihen, kuinka paljon tulevaisuudessa ylijäämälämpöä hyödynnetään rakennusten lämmittämisessä.

The laser weldability of lean duplex stainless steels

Ruostumattomien terästen hinta on kasvanut maailman laajuisen kysynnän kasvun seurauksena. Samoin on käynyt myös ruostumattomien terästen valmistukseen käytettävien seosaineiden hinnalle. Terästen valmistajat ovatkin kehittäneet lean duplex teräksiä vastatakseen hintatietoisten markkinoiden kysyntään. Näissä lean duplex teräksissä kalliita seosaineita kuten nikkeliä ja molybdeenia on korvattu typellä ja mangaanilla. Houkutteleviksi vaihtoehdoiksi perinteisille ruostumattomille teräksille lean duplex laadut tekee myös niiden hyvät lujuus- ja korroosio-ominaisuudet. Kirjallisuus osio esittelee lasereiden toimintaperiaatteen. Myös avaimenreikähitsauksen periaate on esitetty. Ruostumattomien terästen yleisimmät seosaineet ovat esitelty, kuten myös syy niiden seostamiseen. Ruostumattomat duplex-teräkset on esitelty samoin kuin lean duplex teräkset. Kokeellisen osion koehitsit hitsattiin osin samalla tuotantolinjalla lopputuotteen kanssa ja osin laboratoriossa. Koemateriaaleina olivat lean duplex teräkset 1.4162 ja 1.4362 joiden materiaalipaksuudet olivat 1.2 mm ja 1.5 mm. Hitsatuille lamelleille tehtiin painetestaus. Makroskopiaa ja valomikroskopiaa käytettiin koehitsien arvioinnissa kuten myös ristivetokoetta. Kiinnostavimmista hitseistä määritettiin myös faasisuhde. Lean duplex teräs 1.4362 havaittiin sopivammaksi laaduksi tämän kaltaisessa sovelluksessa, mutta myös laatu 1.4162 täyttää sovelluksen hitsille asetetut vaatimukset, tosin huomattavasti pienemmässä parametri ikkunassa. Valittu menetelmä faasisuhteen määrittämiseen osoittautui epätarkaksi, joten faasisuhteen osalta tämän tutkimuksen tulokset ovat vain suuntaa-antavia.

Optimal trading of wind power in the short term market

The energy reform, which is happening all over the world, is caused by the common concern of the future of the humankind in our shared planet. In order to keep the effects of the global warming inside of a certain limit, the use of fossil fuels must be reduced. The marginal costs of the renewable sources, RES are quite high, since they are new technology. In order to induce the implementation of RES to the power grid and lower the marginal costs, subsidies were developed in order to make the use of RES more profitable. From the RES perspective the current market is developed to favor conventional generation, which mainly uses fossil fuels. Intermittent generation, like wind power, is penalized in the electricity market since it is intermittent and thus diffi-cult to control. Therefore, the need of regulation and thus the regulation costs to the producer differ, depending on what kind of generation market participant owns. In this thesis it is studied if there is a way for market participant, who has wind power to use the special characteristics of electricity market Nord Pool and thus reach the gap between conventional generation and the intermittent generation only by placing bids to the market. Thus, an optimal bid is introduced, which purpose is to minimize the regulation costs and thus lower the marginal costs of wind power. In order to make real life simulations in Nord Pool, a wind power forecast model was created. The simulations were done in years 2009 and 2010 by using a real wind power data provided by Hyötytuuli, market data from Nord Pool and wind forecast data provided by Finnish Meteorological Institute. The optimal bid needs probability intervals and therefore the methodology to create probability distributions is introduced in this thesis. In the end of the thesis it is shown that the optimal bidding improves the position of wind power producer in the electricity market.

Simulation and optimization of IGCC technique for power generation and hydrogen production by using lignite Thar coal and cotton stalk

The purpose of this study was to simulate and to optimize integrated gasification for combine cycle (IGCC) for power generation and hydrogen (H2) production by using low grade Thar lignite coal and cotton stalk. Lignite coal is abundant of moisture and ash content, the idea of addition of cotton stalk is to increase the mass of combustible material per mass of feed use for the process, to reduce the consumption of coal and to increase the cotton stalk efficiently for IGCC process. Aspen plus software is used to simulate the process with different mass ratios of coal to cotton stalk and for optimization: process efficiencies, net power generation and H2 production etc. are considered while environmental hazard emissions are optimized to acceptance level. With the addition of cotton stalk in feed, process efficiencies started to decline along with the net power production. But for H2 production, it gave positive result at start but after 40% cotton stalk addition, H2 production also started to decline. It also affects negatively on environmental hazard emissions and mass of emissions/ net power production increases linearly with the addition of cotton stalk in feed mixture. In summation with the addition of cotton stalk, overall affects seemed to negative. But the effect is more negative after 40% cotton stalk addition so it is concluded that to get maximum process efficiencies and high production less amount of cotton stalk addition in feed is preferable and the maximum level of addition is estimated to 40%. Gasification temperature should keep lower around 1140 °C and prefer technique for studied feed in IGCC is fluidized bed (ash in dry form) rather than ash slagging gasifier

Economic viability of retrofiting emitters in center pivot irrigation systems

Although several studies have been conducted to evaluate the uniformity of water application under center pivot irrigation systems, there are few studies concerning the economic perspective of such coefficient. The aim of this study is to present a methodology to accomplish an economic analysis as support for the decision-making to retrofit emitters in center pivot irrigation systems, and to attribute an economic meaning to the uniformity coefficient of water application taking into account the response function productivity to the amount of water applied and the sale price of the crops. In the hypothetic calculation example considering the variation of revenue of potato crop under center pivot irrigation system, it was verified that the area with uniformity coefficient of water application of 90% brought an income increase of BR$ 1,992.00, considering an area about 1,0 ha. Thus, it can be concluded that the methodology presented has met the objectives proposed in the study and made it possible to attribute an economical meaning to the coefficient of water uniformity application.

Economic analysis of cashew early dwarf Crop BRS - 189 depending on water levels and doses of potassium fertilization

Water and fertilizer among the production factors are the elements that most restrict the production of cashew. The precise amount of these factors is essential to the success of the crop yield. This research aimed to determine the best factor-product ratio and analyze technical and economic indicators, of productivity of the cashew clone BRS 189 (Anacardium occidentale) to production factors water and potassium. The experiment was conducted from May 2009 to December 2009 in an experimental area of 56.0 m x 112.0 m in the irrigated Curu - Pentecoste, located in the municipality of Pentecoste, Ceará, Brazil. Production factors water (W) and potassium (K) were the independent variables and productivity (Y), the dependent variable. Ten statistical models that have proven satisfactory for obtaining production function were tested. The marginal rate of substitution was obtained through the ratio of the potassium marginal physical product and the water marginal physical product. The most suited model to the conditions of the experiment was the quadratic polynomial without intercept and interaction. Considering that the price of the water was 0.10 R$ mm -1, the price of the potassium 2.19 R$ kg -1 and the price of the cashew 0.60 R$ kg-1, the amounts of water and K2O to obtain the maximum net income were 6,349.1 L plant-1 of water and 128.7 g plant -1year, -1 respectively. Substituting the values obtained in the production function, the maximum net income was achieved with a yield of 7,496.8 kg ha-1 of cashew.

Thinking Outside the Box: Enhancing Science Teaching by Combining (Instead of Contrasting) Laboratory and Simulation Activities

The focus of the present work was on 10- to 12-year-old elementary school students’ conceptual learning outcomes in science in two specific inquiry-learning environments, laboratory and simulation. The main aim was to examine if it would be more beneficial to combine than contrast simulation and laboratory activities in science teaching. It was argued that the status quo where laboratories and simulations are seen as alternative or competing methods in science teaching is hardly an optimal solution to promote students’ learning and understanding in various science domains. It was hypothesized that it would make more sense and be more productive to combine laboratories and simulations. Several explanations and examples were provided to back up the hypothesis. In order to test whether learning with the combination of laboratory and simulation activities can result in better conceptual understanding in science than learning with laboratory or simulation activities alone, two experiments were conducted in the domain of electricity. In these experiments students constructed and studied electrical circuits in three different learning environments: laboratory (real circuits), simulation (virtual circuits), and simulation-laboratory combination (real and virtual circuits were used simultaneously). In order to measure and compare how these environments affected students’ conceptual understanding of circuits, a subject knowledge assessment questionnaire was administered before and after the experimentation. The results of the experiments were presented in four empirical studies. Three of the studies focused on learning outcomes between the conditions and one on learning processes. Study I analyzed learning outcomes from experiment I. The aim of the study was to investigate if it would be more beneficial to combine simulation and laboratory activities than to use them separately in teaching the concepts of simple electricity. Matched-trios were created based on the pre-test results of 66 elementary school students and divided randomly into a laboratory (real circuits), simulation (virtual circuits) and simulation-laboratory combination (real and virtual circuits simultaneously) conditions. In each condition students had 90 minutes to construct and study various circuits. The results showed that studying electrical circuits in the simulation–laboratory combination environment improved students’ conceptual understanding more than studying circuits in simulation and laboratory environments alone. Although there were no statistical differences between simulation and laboratory environments, the learning effect was more pronounced in the simulation condition where the students made clear progress during the intervention, whereas in the laboratory condition students’ conceptual understanding remained at an elementary level after the intervention. Study II analyzed learning outcomes from experiment II. The aim of the study was to investigate if and how learning outcomes in simulation and simulation-laboratory combination environments are mediated by implicit (only procedural guidance) and explicit (more structure and guidance for the discovery process) instruction in the context of simple DC circuits. Matched-quartets were created based on the pre-test results of 50 elementary school students and divided randomly into a simulation implicit (SI), simulation explicit (SE), combination implicit (CI) and combination explicit (CE) conditions. The results showed that when the students were working with the simulation alone, they were able to gain significantly greater amount of subject knowledge when they received metacognitive support (explicit instruction; SE) for the discovery process than when they received only procedural guidance (implicit instruction: SI). However, this additional scaffolding was not enough to reach the level of the students in the combination environment (CI and CE). A surprising finding in Study II was that instructional support had a different effect in the combination environment than in the simulation environment. In the combination environment explicit instruction (CE) did not seem to elicit much additional gain for students’ understanding of electric circuits compared to implicit instruction (CI). Instead, explicit instruction slowed down the inquiry process substantially in the combination environment. Study III analyzed from video data learning processes of those 50 students that participated in experiment II (cf. Study II above). The focus was on three specific learning processes: cognitive conflicts, self-explanations, and analogical encodings. The aim of the study was to find out possible explanations for the success of the combination condition in Experiments I and II. The video data provided clear evidence about the benefits of studying with the real and virtual circuits simultaneously (the combination conditions). Mostly the representations complemented each other, that is, one representation helped students to interpret and understand the outcomes they received from the other representation. However, there were also instances in which analogical encoding took place, that is, situations in which the slightly discrepant results between the representations ‘forced’ students to focus on those features that could be generalised across the two representations. No statistical differences were found in the amount of experienced cognitive conflicts and self-explanations between simulation and combination conditions, though in self-explanations there was a nascent trend in favour of the combination. There was also a clear tendency suggesting that explicit guidance increased the amount of self-explanations. Overall, the amount of cognitive conflicts and self-explanations was very low. The aim of the Study IV was twofold: the main aim was to provide an aggregated overview of the learning outcomes of experiments I and II; the secondary aim was to explore the relationship between the learning environments and students’ prior domain knowledge (low and high) in the experiments. Aggregated results of experiments I & II showed that on average, 91% of the students in the combination environment scored above the average of the laboratory environment, and 76% of them scored also above the average of the simulation environment. Seventy percent of the students in the simulation environment scored above the average of the laboratory environment. The results further showed that overall students seemed to benefit from combining simulations and laboratories regardless of their level of prior knowledge, that is, students with either low or high prior knowledge who studied circuits in the combination environment outperformed their counterparts who studied in the laboratory or simulation environment alone. The effect seemed to be slightly bigger among the students with low prior knowledge. However, more detailed inspection of the results showed that there were considerable differences between the experiments regarding how students with low and high prior knowledge benefitted from the combination: in Experiment I, especially students with low prior knowledge benefitted from the combination as compared to those students that used only the simulation, whereas in Experiment II, only students with high prior knowledge seemed to benefit from the combination relative to the simulation group. Regarding the differences between simulation and laboratory groups, the benefits of using a simulation seemed to be slightly higher among students with high prior knowledge. The results of the four empirical studies support the hypothesis concerning the benefits of using simulation along with laboratory activities to promote students’ conceptual understanding of electricity. It can be concluded that when teaching students about electricity, the students can gain better understanding when they have an opportunity to use the simulation and the real circuits in parallel than if they have only the real circuits or only a computer simulation available, even when the use of the simulation is supported with the explicit instruction. The outcomes of the empirical studies can be considered as the first unambiguous evidence on the (additional) benefits of combining laboratory and simulation activities in science education as compared to learning with laboratories and simulations alone.

Search and Paper SKU Analysis of Recipes Meeting EUPS Standard

The theoretical research of the study concentrated on finding theoretical frameworks to optimize the amount of needed stock keeping units (SKUs) in manufacturing industry. The goal was to find ways for a company to acquire an optimal collection of stock keeping units needed for manufacturing needed amount of end products. The research follows constructive research approach leaning towards practical problem solving. In the empirical part of this study, a recipe search tool was developed to an existing database used in the target company. The purpose of the tools was to find all the recipes meeting the EUPS performance standard and put the recipes in a ranking order using the data available in the database. The ranking of the recipes was formed from the combination of the performance measures and price of the recipes. In addition, the tool researched what kind of paper SKUs were needed to manufacture the best performing recipes. The tool developed during this process meets the requirements. It eases and makes it much faster to search for all the recipes meeting the EUPS standard. Furthermore, many future development possibilities for the tool were discovered while writing the thesis.

Pienvesivoimalan uusinta

Diplomityön tavoitteena on tutkia eri vaihtoehtojen kannattavuutta pienvesivoimalan uusinnassa. Sähkönhinnan muodostus ja tulokseen vaikuttavat tekijät käsitellään kokonaisuuksinaan. Työssä tehdään kustannuslaskenta valmistajien tarjouksien perusteella ja suoritetaan esittely eri tarjouksista. Valmisteluosassa tutustutaan mitoitusarvoihin ja jos niitä ei ole miten ne selvitetään. Mittauksen kautta saadut arvot käsitellään ja sovelletaan siten, että valmistajat pystyvät käyttämään niitä. Lisäksi tutustutaan turbiinin laskentaan ja mitoitetaan Kaplan-turbiini työssä käytettyyn pienvesivoimalaan.