Behaviour of TiO(2)-SiMgO(x) hybrid composites on the solar photocatalytic degradation of polluted air

The photocatalytic performance of TiO(2)-SiMgO(x) ceramic plates for trichloroethylene abatement in gas phase has been evaluated under sun irradiance conditions. A continuous flow Pyrex glass reactor fixed on the focus of a compound parabolic collector has been used. The performance of the hybrid photocatalyst has been evaluated as the variation of TCE conversion and reaction products formation with the solar irradiance at different total gas flow, TCE concentration, and water vapour content. SiMgO(x) not only provides adsorbent properties to the photocatalyst, but it also allows the effective use of the material during low solar irradiance conditions. The adsorption-desorption phenomena play a pivotal role in the behaviour of the system. Thus, TCE conversion curves present two different branches when the sun irradiance increases (sunrise) or decreases (sunset). CO(2), COCl(2) and DCAC were the most relevant products detected. Meanwhile CO(2) concentration was insensitive to the branch analysed, COCl(2) or DCAC were not indicating the ability of these compounds to be adsorbed on the composite. An increase of the UV irradiation at total TCE conversion promotes the CO(2) selectivity. The excess of energy arriving to the reactor favours the direct reaction pathway to produce CO(2). The photonic efficiency, calculated as a function of the rate of CO(2) formation, decreases linearly with the solar irradiance up to around 2 mW cm(-2), where it becomes constant. For decontamination systems high TCE conversion is pursuit and then high solar irradiance values are required, in spite of lower photonic efficiency values. The present photocatalyst configuration, with only 17% of the reactor volume filled with the photoactive material, allows total TCE conversion for 150 ppm and 1 L min(-1) in a wide sun irradiance window from 2 to 4 mW cm(-2). The incorporation of water vapour leads to an increase of the CO(2) selectivity keeping the TCE conversion around 90%, although significant amounts of COCl(2) were observed. (c) 2010 Elsevier B.V. All rights reserved.

Decolourisation of real textile waste using electrochemical techniques: Effect of electrode composition

The present paper presents the study of the decolourisation of real textile effluent by constant current electrolysis in a flow-cell using a DSAO type material. The effect of using different anode materials (Ti/Ru0.3Ti0.7O2; Ti/Ir0.3Ti0.7O2; Ti/RuxSn1-xO2, where X = 0.1, 0.2 or 0.3) on the efficiency of colour removal is discussed. Attempts to perform galvanostatic oxidation (40 and 60 mA cm(-2)) on the as-received effluent demonstrate that colour removal and total organic carbon (TOC) removal are limited. In this case the greatest degree of colour removal is achieved when anode containing 90% SnO2 is used. If the conductivity of the effluent is increased by adding NaCl (0.1 mol L-1) appreciable colour/TOC removal is observed. The efficiencies of colour and TOC removal are discussed in terms of the energy per order (E-EO/kWhm(-3) order(-1)) and energy consumption (E-C/kW h kg(-1) TOC), respectively. Finally, the extent of colour removal is compared to consent levels presented in the literature. (C) 2008 Elsevier B.V. All rights reserved.

Electrocombustion of humic acid and removal of algae from aqueous solutions

This paper reports experiments involving the electrochemical combustion of humic acid (HA) and removal of algae from pond water. An electrochemical flow reactor with a boron-doped diamond film anode was used and constant current experiments were conducted in batch recirculation mode. The mass transfer characteristics of the electrochemical device were determined by voltammetric experiments in the potential region of water stability, followed by a controlled current experiment in the potential region of oxygen evolution. The average mass transfer coefficient was 5.2 x 10(-5) m s(-1). The pond water was then processed to remove HA and algae in the conditions in which the reaction combustion occurred under mass transfer control. To this end, the mass transfer coefficient was used to estimate the initial limiting current density applied in the electrolytic experiments. As expected, all the parameters analyzed here-solution absorbance at 270 nm, total phenol concentration and total organic carbon concentration-decayed according to first-order kinetics. Since the diamond film anode successfully incinerated organic matter, the electrochemical system proved to be predictable and programmable.

SnO(2)-based materials for pesticide degradation

This study presents the results of the degradation of the pesticide atrazine using electrochemical and photo-assisted electrochemical degradation techniques using SnO(2)-containing electrode of nominal composition electrodes of composition Ti/Ru(x)Sni-(x)O(2) (where X = 0.10, 0.15, 0.20, 0.25 and 0.30). The materials were characterized ex situ and in situ in order to correlate the observed atrazine removal rates with electrode morphology/composition. The results obtained demonstrate the effectiveness of the photo-assisted electrochemical degradation. Using purely electrochemical methods the rate of atrazine removal is almost zero at all the electrodes studied. However, the application of photo-assisted degradation results in almost complete atrazine removal in 1 h of electrolysis. The efficiency of atrazine degradation does not seem to be greatly affected by the electrode material or by SnO(2) content, but the overall COD removal is dependent on the SnO(2) content. Overall, the SnO(2)-containing electrodes do not reach the level of COD removal (maximum similar to 21%) seen for the Ti/Ru(0.3)Ti(0.2)O(2) electrode. An interesting correlation between the morphology factor (phi) and chemical oxygen demand removal is observed. (C) 2010 Elsevier B.V. All rights reserved.

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Projeto, construção e análise de um prototipo vibracional em escala de bancada aplicável ao tratamento de água de produção de petróleo bruto, mediante inovadora operação híbrida de adsorção e auto-flotação

A self-flotator vibrational prototype electromechanical drive for treatment of oil and water emulsion or like emulsion is presented and evaluated. Oil production and refining to obtain derivatives is carried out under arrangements technically referred to as on-shore and off-shore, ie, on the continent and in the sea. In Brazil 80 % of the petroleum production is taken at sea and area of deployment and it cost scale are worrisome. It is associated, oily water production on a large scale, carrier 95% of the potential pollutant of activity whose final destination is the environment medium, terrestrial or maritime. Although diversified set of techniques and water treatment systems are in use or research, we propose an innovative system that operates in a sustainable way without chemical additives, for the good of the ecosystem. Labyrinth adsor-bent is used in metal spirals, and laboratory scale flow. Equipment and process patents are claimed. Treatments were performed at different flow rates and bands often monitored with control systems, some built, other bought for this purpose. Measurements of the levels of oil and grease (OGC) of efluents treaty remained within the range of legal framework under test conditions. Adsorbents were weighed before and after treatment for obtaining oil impregna-tion, the performance goal of vibratory action and treatment as a whole. Treatment technolo-gies in course are referenced, to compare performance, qualitatively and quantitatively. The vibration energy consumption is faced with and without conventional flotation and self-flotation. There are good prospects for the proposed, especially in reducing the residence time, by capillary action system. The impregnation dimensionless parameter was created and confronted with consecrated dimensionless parameters, on the vibrational version, such as Weber number and Froude number in quadratic form, referred to as vibrational criticality. Re-sults suggest limits to the vibration intensity

Avaliação da genotoxicidade e da qualidade das águas do açude de Lucrécia/RN

The occurrence of human cancer in the municipality of Lucrécia (RN, Brazil) has shown high frequencies (INCA, 2007). Tests of micronucleus (MN) and nuclear abnormalities (NA) were performed to assess the genotoxic potential of water from the Lucrécia dam, which is located in a semi-arid region under the influence of crop irrigation and irregular rainfall. Water samples were collected in this source for analyzing the concentration of cyanobacteria, metals and radioactivity. Erythrocytes of Nile tilapia (Oreochromis niloticus) were collected in dam and cells of human oral mucosa in the urban area of this municipality for the bioassays of MN and NA. In fish were also analyzed concentrations of metals in samples of liver and gills. The genotoxicity tests with biological samples of fish and humans have shown significant increases in the frequencies of MN and NA (p ≤ 0.05) and are indicative of increased DNA damage in relation to the control groups. In conclusion, the results obtained from water samples and biological municipality of Lucrécia indicates that the presence of chemical and microbiological pollutants, and increase of genotoxic in human of this municipality. We suggest the implementation of advanced water treatment, to prevent further degradation of the aquatic environment and decrease in the life quality. This research of environmental quality assessment was performed in order to contemplate a multi and interdisciplinary character of this water resource and that can induce genotoxic damage in the organisms in this study region

Análise da presença de agentes mutagênicos nas águas do Rio Pitimbú/RN

The Pitimbu River is located at the oriental portion of the State of Rio Grande do Norte, including three importants cities named Macaíba, Parnamirim e Natal. Although its high importance as a water source, which supplys great part of the South Zone of the Natal city, this river receives a large quantity of domestic and industrial waste water without treatment. The Pitimbu River headhas its river-head located in the city of Macaiba, goes through Parnamirim, then it flowing into at the Jiqui Lake in Natal. The aim of this study was to evaluate, qualitatively and quantitatively, the environmental quality of the Pitimbu River by genotoxicity bio-assays, which are important tools for genetics toxicological evaluation. In this work, five samples sites, distributed along the river, were used to collect water samples. Another point site, located near Jiqui lake, was used to collect drinkable water, which was treated by CAERN, the water treatment entreprise of Rio Grande do Norte. The following assays where used to evaluate the quality of these samples: Allium cepa assay; Comet assay; Micronuclei (MN) assay; and Ames test. For the Allium cepa assay, sixteen specimes where used for each water sample from the sample sites. In this assay both microscopic, like cytogenetic damage, and macroscopic aspects, as morphological variation were evaluated. Red blood cells from periferical blood of the Crenicichla menezesi native specie were used not only for the MN assay, but also for the Comet assay. These fishes were collected at different points on the Pitimbu River and the negative control was developed using fishes of the same species that were bring to the laboratory and maintained for 100 days in the optimal experimental conditions. For the Ames test, TA100, YG1042, TA98 and YG1041 strains were used in the directed method without metabolic activation. The results found by the Allium cepa assay showed that two water sample sites induced increase of mitotic index (IM). Additionally, compared to the control, all the water samples increased the chromossomal aberrations frequency and/or micronucleus. Among the sample sites, two also showed an abnormal growth rate in its root and two samples induced morphological alteration. With the MN test in red blood cells, a high frequence of MN was observed in tree sample. By comparing all the results obtained on the water sample points and with the negative control, a significant variation on the MN frequency was observed. Positive results were also observed for the same sample to water test by the Comet assay. These results allow concluding that the proposed specie Crenicichla menezesi has a good profile as a bio-indicator for the evaluation of environmental water quality and the MN and comet test can be usuful for in situ evaluation. By the Ames test, it was possible to detect the mutagenic activity on the waters from the Pitimbu River in different levels of mutagenicity. This result suggests that this river has several substances that induced changes directly to the DNA. The mechanisms involved to this phenomenon could be by both processes, by changing of the reading frame and by nucleotide substitution. These data set indicate the presence of mutagenic agents, which can represent in risk to biot and human beens

Avaliação dos efeitos de um extrato bruto de cianobactérias contendo microcistinas sobre o desempenho reprodutivo e a embriofetotoxicidade de ratos

The presence of cyanobacterial blooms in reservoirs intended for supply to the population can create public health problems for many species could produce potentially toxic compounds and these are not eliminated in the conventional procedures used in water treatment plants. So even in amounts less than the maximum allowable limit imposed by MS, cyanotoxins can be present in drinking water distributed to the population, creating a chronic exposure. There is little information about the long-term effects of oral exposure to cyanotoxins. This work aimed to show the exposure orally (v.o) of animals to a crude extract of cyanobacteria containing cyanotoxins to evaluate the reproductive performance of pregnant rats and their offspring and fertility of male rats. The presence of microcystins (MCs) in samples collected during the flowering processes in freshwater reservoirs in the Rio Grande do Norte, was analyzed by enzyme immunoassay and its variants have been identified and quantified by chromatographic methods. It was observed that by administration v.o. cyanobacterial extract containing MCs (40, 100 or 250 ng of MCs / kg / day) did not cause systemic toxicity in adult rats or effect on reproductive performance of male and female rats treated. It was also not observed any changes in skeletal study in the offspring of pregnant rats treated with the extract above. Because the solutions used contained MCs in a concentration equal to or greater than the tolerable daily intake for MCs, the results suggest, therefore, that the development of this work contributed to better assess public health risk as the oral exposure to cyanotoxins, increasing thus the credibility of the maximum allowable limit (LMP) of MCs in drinking water distributed to the population of several countries that use the LMP established by WHO in its legislation

Sistema com aeração, decantação e filtragem para a melhoria da qualidade de água em irrigação localizada

A qualidade da água é muito importante para irrigação por gotejamento, pois ela escoa por pequenos bocais dos emissores, podendo ocorrer obstrução devido à deposição dos sólidos em suspensão. Portanto, antes da instalação do projeto, devem-se avaliar parâmetros de qualidade da água, para adotar medidas preventivas, evitando o risco de entupimento do sistema. Este trabalho teve como objetivo avaliar um sistema composto por aeradores com aspersores, sobre leito de pedra, para a precipitação dos íons Fe+2e Mn+2 em tanque de decantação, e um conjunto de filtragem composto por três filtros de areia e um de disco, em sistema de irrigação localizada. O trabalho foi realizado na Fazenda Alvorada, no município de Nova Granada - SP, no período de março a outubro de 2008. Foram realizadas determinações de variáveis físicas e químicas da água, ao longo do sistema de aeração, decantação e filtragem, o qual foi eficiente para a melhoria da qualidade de água, reduzindo os níveis de risco de entupimento de severo para médio e de médio para baixo. Oxigênio dissolvido, condutividade elétrica, pH, Fe+2e Fe+3 não diferenciaram a qualidade de água entre os pontos do sistema de tratamento, porém a turbidez, sólidos dissolvidos, sólidos em suspensão, ferro total e manganês total reduziram-se significativamente pelo uso do sistema proposto, melhorando a qualidade da água.

Água de consumo humano como fator de risco à saúde em propriedades rurais

OBJETIVO: Verificar a qualidade higiênico-sanitária da água de consumo humano em propriedades rurais por meio da contagem de indicadores microbiológicos de potabilidade. MÉTODOS: Foram colhidas 180 amostras de água utilizada para consumo humano das fontes, reservatórios e ponto de consumo em 30 propriedades rurais, situadas na região Nordeste do Estado de São Paulo. Determinou-se o número mais provável de coliformes totais, Escherichia coli e o número de microrganismos mesófilos. Foi verificada a presença de medidas de proteção das fontes de abastecimento. RESULTADOS: Os resultados evidenciaram que 90% das amostras de água das fontes, 90% dos reservatórios e 96,7% de água de consumo humano, colhidas no período de chuvas, e 83,3%, 96,7% e 90%, daquelas colhidas respectivamente nos mesmos locais, durante a estiagem, estavam fora dos padrões microbiológicos de potabilidade para água de consumo humano. CONCLUSÕES: A água utilizada nas propriedades rurais foi considerada um importante fator de risco à saúde dos seres humanos que a utilizam. A adoção de medidas preventivas, visando à preservação das fontes de água, e o tratamento das águas já comprometidas são as ferramentas necessárias para diminuir consideravelmente o risco de ocorrência de enfermidades de veiculação hídrica.

Preliminary results of a floating subirrigation system (Aquaforest system) as an alternative to conventional tree nurseries

A new methodology for tree seedling production (Aquaforest system) based on a continuous floating subirrigation system was developed and tested using creeks with different nutrient levels. Eucalyptus grandis seedlings were produced in water from polluted and clean creeks, and compared to conventional tree nursery production. The growth variables analyzed in the seedling phase were: survival, height, diameter, shoot and root dry weight, leaf area, and root/shoot ratio. Water and substrate were analyzed, as well as leaf nutritional status. Plant survival was 100% in all treatments. Height and diameter were greater in the higher nutrient water treatment. Leaf area and dry weight of plants produced in the higher nutrient water treatment were similar to those of the control. The results showed that polluted water can represent a good nutrient source. The preliminary results show that the Aquaforest system can be a viable alternative for tree seedling production. (C) 2004 Elsevier B.V. All rights reserved.

Remoção conjugada de metais e óleo de água produzida

Petroleum can be associated or not with natural gas, but in both cases water is always present in its formation. The presence of water causes several problems, such as the difficulty of removing the petroleum from the reservoir rock and the formation of waterin-oil and oil-in-water emulsions. The produced water causes environmental problems, which should be solved to reduce the effect of petroleum industry in the environment. The main objective of this work is to remove simultaneously from the produced water the dispersed petroleum and dissolved metals. The process is made possible through the use of anionic surfactants that with its hydrophilic heads interacts with ionized metals and with its lipophilic tails interacts with the oil. The studied metals were: calcium, magnesium, barium, and cadmium. The surfactants used in this research were derived from: soy oil, sunflower oil, coconut oil, and a soap obtained from a mixture of 5wt.% coconut oil and 95wt.% animal fat. It was used a sample of produced water from Terminal de São Sebastião, São Paulo. As the concentration of the studied metals in produced water presented values close to 300 mg/L, it was decided to use this concentration as reference for the development of this research. Molecular absorption and atomic absorption spectroscopy were used to determine petroleum and metals concentrations in the water sample, respectively. A constant pressure filtration system was used to promote the separation of solid and liquid phases. To represent the behavior of the studied systems it was developed an equilibrium model and a mathematical one. The obtained results showed that all used surfactants presented similar behavior with relation to metals extraction, being selected the surfactant derived from soy oil for this purpose. The values of the partition coefficients between the solid and liquid phases " D " for the studied metals varied from 0.2 to 1.1, while the coefficients for equilibrium model " K " varied from 0.0002 and 0.0009. The removal percentile for oil with all metals associated was near 100%, showing the efficiency of the process

Extração enzimática de óleo e produção in situ de biodiesel a partir da Moringa oleífera Lam

With the growth and development of modern society, arises the need to search for new raw materials and new technologies which present the "clean" characteristic, and do not harm the environment, but can join the energy needs of industry and transportation. The Moringa oleifera Lam, plant originating from India, and currently present in the Brazilian Northeast, presents itself as a multi-purpose plant, can be used as a coagulant in water treatment, as a natural remedy and as a feedstock for biodiesel production. In this work, Moringa has been used as a raw material for studies on the extraction and subsequently in the synthesis of biodiesel. Studies have been conducted on various techniques of Moringa oil extraction (solvents, mechanical pressing and enzymatic), being specially developed an experimental design for the aqueous extraction with the aid of the enzyme Neutrase© 0.8 L, with the aim of analyzing the influence variable pH (5.5-7.5), temperature (45-55°C), time (16-24 hours) and amount of catalyst (2-5%) on the extraction yield. In relation to study of the synthesis of biodiesel was initially carried out a conventional transesterification (50°C, KOH as a catalyst, methanol and 60 minutes reaction). Next, a study was conducted using the technique of in situ transesterification by using an experimental design variables as temperature (30-60°C), catalyst amount (2-5%), and molar ratio oil / ethanol (1:420-1:600). The extraction technique that achieved the highest extraction yield (35%) was the one that used hexane as a solvent. The extraction using 32% ethanol obtained by mechanical pressing and extraction reached 25% yield. For the enzymatic extraction, the experimental design indicated that the extraction yield was most affected by the effect of the combination of temperature and time. The maximum yield obtained in this extraction was 16%. After the step of obtaining the oil was accomplished the synthesis of biodiesel by the conventional method and the in situ technique. The method of conventional transesterification was obtained a content of 100% and esters by in situ technique was also obtained in 100% in the experimental point 7, with a molar ratio oil / alcohol 1:420, Temperature 60°C in 5% weight KOH with the reaction time of 1.5 h. By the experimental design, it was found that the variable that most influenced the ester content was late the percentage of catalyst. By physico-chemical analysis it was observed that the biodiesel produced by the in situ method fell within the rules of the ANP, therefore this technique feasible, because does not require the preliminary stage of oil extraction and achieves high levels of esters