Performance control of distributed generation using digital estimation of signal parameters

The Queensland University of Technology (QUT) allows the presentation of a thesis for the Degree of Doctor of Philosophy in the format of published or submitted papers, where such papers have been published, accepted or submitted during the period of candidature. This thesis is composed of seven published/submitted papers, of which one has been published, three accepted for publication and the other three are under review. This project is financially supported by an Australian Research Council (ARC) Discovery Grant with the aim of proposing strategies for the performance control of Distributed Generation (DG) system with digital estimation of power system signal parameters. Distributed Generation (DG) has been recently introduced as a new concept for the generation of power and the enhancement of conventionally produced electricity. Global warming issue calls for renewable energy resources in electricity production. Distributed generation based on solar energy (photovoltaic and solar thermal), wind, biomass, mini-hydro along with use of fuel cell and micro turbine will gain substantial momentum in the near future. Technically, DG can be a viable solution for the issue of the integration of renewable or non-conventional energy resources. Basically, DG sources can be connected to local power system through power electronic devices, i.e. inverters or ac-ac converters. The interconnection of DG systems to power system as a compensator or a power source with high quality performance is the main aim of this study. Source and load unbalance, load non-linearity, interharmonic distortion, supply voltage distortion, distortion at the point of common coupling in weak source cases, source current power factor, and synchronism of generated currents or voltages are the issues of concern. The interconnection of DG sources shall be carried out by using power electronics switching devices that inject high frequency components rather than the desired current. Also, noise and harmonic distortions can impact the performance of the control strategies. To be able to mitigate the negative effect of high frequency and harmonic as well as noise distortion to achieve satisfactory performance of DG systems, new methods of signal parameter estimation have been proposed in this thesis. These methods are based on processing the digital samples of power system signals. Thus, proposing advanced techniques for the digital estimation of signal parameters and methods for the generation of DG reference currents using the estimates provided is the targeted scope of this thesis. An introduction to this research – including a description of the research problem, the literature review and an account of the research progress linking the research papers – is presented in Chapter 1. One of the main parameters of a power system signal is its frequency. Phasor Measurement (PM) technique is one of the renowned and advanced techniques used for the estimation of power system frequency. Chapter 2 focuses on an in-depth analysis conducted on the PM technique to reveal its strengths and drawbacks. The analysis will be followed by a new technique proposed to enhance the speed of the PM technique while the input signal is free of even-order harmonics. The other techniques proposed in this thesis as the novel ones will be compared with the PM technique comprehensively studied in Chapter 2. An algorithm based on the concept of Kalman filtering is proposed in Chapter 3. The algorithm is intended to estimate signal parameters like amplitude, frequency and phase angle in the online mode. The Kalman filter is modified to operate on the output signal of a Finite Impulse Response (FIR) filter designed by a plain summation. The frequency estimation unit is independent from the Kalman filter and uses the samples refined by the FIR filter. The frequency estimated is given to the Kalman filter to be used in building the transition matrices. The initial settings for the modified Kalman filter are obtained through a trial and error exercise. Another algorithm again based on the concept of Kalman filtering is proposed in Chapter 4 for the estimation of signal parameters. The Kalman filter is also modified to operate on the output signal of the same FIR filter explained above. Nevertheless, the frequency estimation unit, unlike the one proposed in Chapter 3, is not segregated and it interacts with the Kalman filter. The frequency estimated is given to the Kalman filter and other parameters such as the amplitudes and phase angles estimated by the Kalman filter is taken to the frequency estimation unit. Chapter 5 proposes another algorithm based on the concept of Kalman filtering. This time, the state parameters are obtained through matrix arrangements where the noise level is reduced on the sample vector. The purified state vector is used to obtain a new measurement vector for a basic Kalman filter applied. The Kalman filter used has similar structure to a basic Kalman filter except the initial settings are computed through an extensive math-work with regards to the matrix arrangement utilized. Chapter 6 proposes another algorithm based on the concept of Kalman filtering similar to that of Chapter 3. However, this time the initial settings required for the better performance of the modified Kalman filter are calculated instead of being guessed by trial and error exercises. The simulations results for the parameters of signal estimated are enhanced due to the correct settings applied. Moreover, an enhanced Least Error Square (LES) technique is proposed to take on the estimation when a critical transient is detected in the input signal. In fact, some large, sudden changes in the parameters of the signal at these critical transients are not very well tracked by Kalman filtering. However, the proposed LES technique is found to be much faster in tracking these changes. Therefore, an appropriate combination of the LES and modified Kalman filtering is proposed in Chapter 6. Also, this time the ability of the proposed algorithm is verified on the real data obtained from a prototype test object. Chapter 7 proposes the other algorithm based on the concept of Kalman filtering similar to those of Chapter 3 and 6. However, this time an optimal digital filter is designed instead of the simple summation FIR filter. New initial settings for the modified Kalman filter are calculated based on the coefficients of the digital filter applied. Also, the ability of the proposed algorithm is verified on the real data obtained from a prototype test object. Chapter 8 uses the estimation algorithm proposed in Chapter 7 for the interconnection scheme of a DG to power network. Robust estimates of the signal amplitudes and phase angles obtained by the estimation approach are used in the reference generation of the compensation scheme. Several simulation tests provided in this chapter show that the proposed scheme can very well handle the source and load unbalance, load non-linearity, interharmonic distortion, supply voltage distortion, and synchronism of generated currents or voltages. The purposed compensation scheme also prevents distortion in voltage at the point of common coupling in weak source cases, balances the source currents, and makes the supply side power factor a desired value.

The promise and possibilities of music, digital media and National Broadband Network

In this article I would like to examine the promise and possibilities of music, digital media and National Broadband Network. I will do this based on concepts that have emerged from a study undertaken by Professor Andrew Brown and I that categorise technologies into what we term representational technologies and technologies with agency

Calcium ions promote osteogenic differentiation and mineralization of human dental pulp cells : implication for pulp capping materials

Calcium (Ca) is the main element of most pulp capping materials and plays an essential role in mineralization. Different pulp capping materials can release various concentrations of Ca ions leading to different clinical outcomes. The purpose of this study was to investigate the effects of various concentrations of Ca ions on the growth and osteogenic differentiation of human dental pulp cells (hDPCs). Different concentrations of Ca ions were added to growth culture medium and osteogenic inductive culture medium. A Cell Counting Kit-8 (CCK-8) was used to determine the proliferation of hDPCs in growth culture medium. Osteogenic differentiation and mineralization were measured by alkaline phosphatase (ALP) assay, Alizarin red S/von kossa staining, calcium content quantitative assay. The selected osteogenic differentiation markers were investigated by quantitative real-time polymerase chain reaction (qRT-PCR). Within the range of 1.8–16.2 mM, increased concentrations of Ca ions had no effect on cell proliferation, but led to changes in osteogenic differentiation. It was noted that enhanced mineralized matrix nodule formation was found in higher Ca ions concentrations; however, ALP activity and gene expression were reduced. qRT-PCR results showed a trend towards down-regulated mRNA expression of type I collagen (COL1A2) and Runx2 at elevated concentrations of Ca ions, whereas osteopontin (OPN) and osteocalcin (OCN) mRNA expression was significantly up-regulated. Ca ions content in the culture media can significantly influence the osteogenic properties of hDPCs, indicating the importance of optimizing Ca ions release from dental pulp capping materials in order to achieve desirable clinical outcomes.

Digital economy future directions

Advances in information and communication technologies have brought about an information revolution, leading to fundamental changes in the way information is collected or generated, shared and distributed. The internet and digital technologies are re-shaping research, innovation and creativity. Economic research has highlighted the importance of information flows and the availability of information for access and re-use. Information is crucial to the efficiency of markets and enhanced information flows promote creativity, innovation and productivity. There is a rapidly expanding body of literature which supports the economic and social benefits of enabling access to and re-use of public sector information.1 (Note that a substantial research project associated with QUT’s Intellectual Property: Knowledge, Culture and Economy (IPKCE) Research Program is engaged in a comprehensive study and analysis of the literature on the economics of access to public sector information.)

Digital reflections on learning : a monograph by students of Digital Pedagogies, Semester 2, 2011

Learning a digital tool is often a hidden process. We tend to learn new tools in a bewildering range of ways. Formal, informal, structured, random, conscious, unconscious, individual, group strategies, may all play a part, but are often lost to us in the complex and demanding processes of learning. But when we reflect carefully on the experience, some patterns and surprising techniques emerge. This monograph presents the thinking of four students in MDN642, Digital Pedagogies, where they have deliberately reflected on the mental processes at work as they learnt a digital technology of their choice.

Five senses digital stories

These digital stories were produced during a commercial research project with SLQ and Flying Arts. The works build on the research of Klaebe and Burgess related to variable workshop scenarios, and the institutional contexts of co-creative media. In this instance, research focused on the distributed digital storytelling workshop model; and the development of audiences for digital storytelling. The research team worked with regional artists whose work had been selected for inclusion in the Five Senses exhibition held at the State Library of Queensland to produce stories about their work; these works were then in turn integrated into the physical exhibition space. Location remoteness and timeline were factors in how the stories were made in a mix of individual meetings and remote correspondence (email &phone).

Country of Origin and Internet Publication : Applying the Berne Convention in the Digital Age

Historically, determining the country of origin of a published work presented few challenges, because works were generally published physically – whether in print or otherwise – in a distinct location or few locations. However, publishing opportunities presented by new technologies mean that we now live in a world of simultaneous publication – works that are first published online are published simultaneously to every country in world in which there is Internet connectivity. While this is certainly advantageous for the dissemination and impact of information and creative works, it creates potential complications under the Berne Convention for the Protection of Literary and Artistic Works (“Berne Convention”), an international intellectual property agreement to which most countries in the world now subscribe. Under the Berne Convention’s national treatment provisions, rights accorded to foreign copyright works may not be subject to any formality, such as registration requirements (although member countries are free to impose formalities in relation to domestic copyright works). In Kernel Records Oy v. Timothy Mosley p/k/a Timbaland, et al. however, the Florida Southern District Court of the United States ruled that first publication of a work on the Internet via an Australian website constituted “simultaneous publication all over the world,” and therefore rendered the work a “United States work” under the definition in section 101 of the U.S. Copyright Act, subjecting the work to registration formality under section 411. This ruling is in sharp contrast with an earlier decision delivered by the Delaware District Court in Håkan Moberg v. 33T LLC, et al. which arrived at an opposite conclusion. The conflicting rulings of the U.S. courts reveal the problems posed by new forms of publishing online and demonstrate a compelling need for further harmonization between the Berne Convention, domestic laws and the practical realities of digital publishing. In this article, we argue that even if a work first published online can be considered to be simultaneously published all over the world it does not follow that any country can assert itself as the “country of origin” of the work for the purpose of imposing domestic copyright formalities. More specifically, we argue that the meaning of “United States work” under the U.S. Copyright Act should be interpreted in line with the presumption against extraterritorial application of domestic law to limit its application to only those works with a real and substantial connection to the United States. There are gaps in the Berne Convention’s articulation of “country of origin” which provide scope for judicial interpretation, at a national level, of the most pragmatic way forward in reconciling the goals of the Berne Convention with the practical requirements of domestic law. We believe that the uncertainties arising under the Berne Convention created by new forms of online publishing can be resolved at a national level by the sensible application of principles of statutory interpretation by the courts. While at the international level we may need a clearer consensus on what amounts to “simultaneous publication” in the digital age, state practice may mean that we do not yet need to explore textual changes to the Berne Convention.

Digital complementary assets

Google, Facebook, Twitter, LinkedIn, etc. are some of the prominent large-scale digital service providers that are having tremendous impact on societies, corporations and individuals. However, despite the rapid uptake and their obvious influence on the behavior of individuals and the business models and networks of organizations, we still lack a deeper, theory-guided understanding of the related phenomenon. We use Teece’s notion of complementary assets and extend it towards ‘digital complementary assets’ (DCA) in an attempt to provide such a theory-guided understanding of these digital services. Building on Teece’s theory, we make three contributions. First, we offer a new conceptualization of digital complementary assets in the form of digital public goods and digital public assets. Second, we differentiate three models for how organizations can engage with such digital complementary assets. Third, user-base is found to be a critical factor when considering appropriability.

On the robustness and security of digital image watermarking

In most of the digital image watermarking schemes, it becomes a common practice to address security in terms of robustness, which is basically a norm in cryptography. Such consideration in developing and evaluation of a watermarking scheme may severely affect the performance and render the scheme ultimately unusable. This paper provides an explicit theoretical analysis towards watermarking security and robustness in figuring out the exact problem status from the literature. With the necessary hypotheses and analyses from technical perspective, we demonstrate the fundamental realization of the problem. Finally, some necessary recommendations are made for complete assessment of watermarking security and robustness.

Engaging new digital locals with interactive urban screens to collaboratively improve the city

Local governments struggle to engage time poor and seemingly apathetic citizens, as well as the city’s young digital natives, the digital locals. This project aims at providing a lightweight, technological contribution towards removing the hierarchy between those who build the city and those who use it. We aim to narrow this gap by enhancing people’s experience of physical spaces with digital, civic technologies that are directly accessible within that space. This paper presents the findings of a design trial allowing users to interact with a public screen via their mobile phones. The screen facilitated a feedback platform about a concrete urban planning project by promoting specific questions and encouraging direct, in-situ, real-time responses via SMS and twitter. This new mechanism offers additional benefits for civic participation as it gives voice to residents who otherwise would not be heard. It also promotes a positive attitude towards local governments and gathers information different from more traditional public engagement tools.

Engaging bodily with video in design

Video is commonly used as a method for recording embodied interaction for purposes of analysis and design and has been proposed as a useful ‘material’ for interaction designers to engage with. But video is not a straight forward reproduction of embodied activity – in themselves video recordings ‘flatten’ the space of embodied interaction, they impose a perspective on unfolding action, and remove the embodied spatial and social context within which embodied interaction unfolds. This does not mean that video is not a useful medium with which to engage as part of a process of investigating and designing for embodied interaction – but crucially, it requires that as people attempting to engage with video, designers own bodies and bodily understandings must be engaged with and brought into play. This paper describes and reflects upon our experiences of engaging with video in two different activities as part of a larger research project investigating the design of gestural interfaces for a dental surgery context.

Strengthening the role of the adult education sector in training workers for the digital content industries in Australia and Singapore

In 2009, QUT’s Office of Research and the Institute for Adult Learning Singapore funded a six-month pilot project that represented the first stage of a larger international comparative study. The study is the first of its kind to investigate to what extent and how digital content workers’ learning needs are being met by adult education and training in Australia and Singapore. The pilot project involved consolidating key theoretical literature, studies, policies, programs and statistical data relevant to the digital content industries in Australia and Singapore. This had not been done before, and represented new knowledge generation. Digital content workers include professionals within and beyond the creative industries as follows: Visual effects and animation (including virtual reality and 3D products); Interactive multimedia (e.g. websites, CD-ROMs) and software development; Computer and online games; and Digital film & TV production and film & TV post-production. In the last decade, the digital content industries have been recognised as an industry sector of strong and increasing significance. The project compared Australia and Singapore on aspects of the digital content industries’ labour market, skill requirements, human capital challenges, the role of adult education in building a workforce for the digital content industries, and innovation policies. The consolidated report generated from the project formed the basis of the proposal for an ARC Linkage Project application submitted in the May 2010 round.

Interfacing Jack and anybody : towards anthropometric musculoskeletal digital human modeling

Virtual prototyping emerges as a new technology to replace existing physical prototypes for product evaluation, which are costly and time consuming to manufacture. Virtualization technology allows engineers and ergonomists to perform virtual builds and different ergonomic analyses on a product. Digital Human Modelling (DHM) software packages such as Siemens Jack, often integrate with CAD systems to provide a virtual environment which allows investigation of operator and product compatibility. Although the integration between DHM and CAD systems allows for the ergonomic analysis of anthropometric design, human musculoskeletal, multi-body modelling software packages such as the AnyBody Modelling System (AMS) are required to support physiologic design. They provide muscular force analysis, estimate human musculoskeletal strain and help address human comfort assessment. However, the independent characteristics of the modelling systems Jack and AMS constrain engineers and ergonomists in conducting a complete ergonomic analysis. AMS is a stand alone programming system without a capability to integrate into CAD environments. Jack is providing CAD integrated human-in-the-loop capability, but without considering musculoskeletal activity. Consequently, engineers and ergonomists need to perform many redundant tasks during product and process design. Besides, the existing biomechanical model in AMS uses a simplified estimation of body proportions, based on a segment mass ratio derived scaling approach. This is insufficient to represent user populations anthropometrically correct in AMS. In addition, sub-models are derived from different sources of morphologic data and are therefore anthropometrically inconsistent. Therefore, an interface between the biomechanical AMS and the virtual human model Jack was developed to integrate a musculoskeletal simulation with Jack posture modeling. This interface provides direct data exchange between the two man-models, based on a consistent data structure and common body model. The study assesses kinematic and biomechanical model characteristics of Jack and AMS, and defines an appropriate biomechanical model. The information content for interfacing the two systems is defined and a protocol is identified. The interface program is developed and implemented through Tcl and Jack-script(Python), and interacts with the AMS console application to operate AMS procedures.

A comprehensive literature review of the pelvis and the lower extremity digital human models under quasi-static conditions

Finite Element Modeling (FEM) has become a vital tool in the automotive design and development processes. FEM of the human body is a technique capable of estimating parameters that are difficult to measure in experimental studies with the human body segments being modeled as complex and dynamic entities. Several studies have been dedicated to attain close-to-real FEMs of the human body (Pankoke and Siefert 2007; Amann, Huschenbeth et al. 2009; ESI 2010). The aim of this paper is to identify and appraise the state of-the art models of the human body which incorporate detailed pelvis and/or lower extremity models. Six databases and search engines were used to obtain literature, and the search was limited to studies published in English since 2000. The initial search results identified 636 pelvis-related papers, 834 buttocks-related papers, 505 thigh-related papers, 927 femur-related papers, 2039 knee-related papers, 655 shank-related papers, 292 tibia-related papers, 110 fibula-related papers, 644 ankle related papers, and 5660 foot-related papers. A refined search returned 100 pelvis-related papers, 45 buttocks related papers, 65 thigh-related papers, 162 femur-related papers, 195 kneerelated papers, 37 shank-related papers, 80 tibia-related papers, 30 fibula-related papers and 102 ankle-related papers and 246 foot-related papers. The refined literature list was further restricted by appraisal against a modified LOW appraisal criteria. Studies with unclear methodologies, with a focus on populations with pathology or with sport related dynamic motion modeling were excluded. The final literature list included fifteen models and each was assessed against the percentile the model represents, the gender the model was based on, the human body segment/segments included in the model, the sample size used to develop the model, the source of geometric/anthropometric values used to develop the model, the posture the model represents and the finite element solver used for the model. The results of this literature review provide indication of bias in the available models towards 50th percentile male modeling with a notable concentration on the pelvis, femur and buttocks segments.

Digital human modelling for vehicle design and manufacturing

Digital human modelling (DHM) has today matured from research into industrial application. In the automotive domain, DHM has become a commonly used tool in virtual prototyping and human-centred product design. While this generation of DHM supports the ergonomic evaluation of new vehicle design during early design stages of the product, by modelling anthropometry, posture, motion or predicting discomfort, the future of DHM will be dominated by CAE methods, realistic 3D design, and musculoskeletal and soft tissue modelling down to the micro-scale of molecular activity within single muscle fibres. As a driving force for DHM development, the automotive industry has traditionally used human models in the manufacturing sector (production ergonomics, e.g. assembly) and the engineering sector (product ergonomics, e.g. safety, packaging). In product ergonomics applications, DHM share many common characteristics, creating a unique subset of DHM. These models are optimised for a seated posture, interface to a vehicle seat through standardised methods and provide linkages to vehicle controls. As a tool, they need to interface with other analytic instruments and integrate into complex CAD/CAE environments. Important aspects of current DHM research are functional analysis, model integration and task simulation. Digital (virtual, analytic) prototypes or digital mock-ups (DMU) provide expanded support for testing and verification and consider task-dependent performance and motion. Beyond rigid body mechanics, soft tissue modelling is evolving to become standard in future DHM. When addressing advanced issues beyond the physical domain, for example anthropometry and biomechanics, modelling of human behaviours and skills is also integrated into DHM. Latest developments include a more comprehensive approach through implementing perceptual, cognitive and performance models, representing human behaviour on a non-physiologic level. Through integration of algorithms from the artificial intelligence domain, a vision of the virtual human is emerging.