Charge transport properties of organic conjugated polymers for photovoltaic applications

Charge transport in conjugated polymers as well as in bulk-heterojunction (BHJ) solar cells made of blends between conjugated polymers, as electron-donors (D), and fullerenes, as electron-acceptors (A), has been investigated. It is shown how charge carrier mobility of a series of anthracene-containing poly(p-phenylene-ethynylene)-alt-poly(p-phenylene-vinylene)s (AnE-PVs) is highly dependent on the lateral chain of the polymers, on a moderate variation of the macromolecular parameters (molecular weight and polydispersity), and on the processing conditions of the films. For the first time, the good ambipolar transport properties of this relevant class of conjugated polymers have been demonstrated, consistent with the high delocalization of both the frontier molecular orbitals. Charge transport is one of the key parameters in the operation of BHJ solar cells and depends both on charge carrier mobility in pristine materials and on the nanoscale morphology of the D/A blend, as proved by the results here reported. A straight correlation between hole mobility in pristine AnE-PVs and the fill factor of the related solar cells has been found. The great impact of charge transport for the performance of BHJ solar cells is clearly demonstrated by the results obtained on BHJ solar cells made of neat-C70, instead of the common soluble fullerene derivatives (PCBM or PC70BM). The investigation of neat-C70 solar cells was motivated by the extremely low cost of non-functionalized fullerenes, compared with that of their soluble derivatives (about one-tenth). For these cells, an improper morphology of the blend leads to a deterioration of charge carrier mobility, which, in turn, increases charge carrier recombination. Thanks to the appropriate choice of the donor component, solar cells made of neat-C70 exhibiting an efficiency of 4.22% have been realized, with an efficiency loss of just 12% with respect to the counterpart made with costly PC70BM.

Vergleichende, prospektive Untersuchung der Arzneimittelcompliance, Funktionskapazität und Lebensqualität bei Patienten mit Rheuma, die mit Methotrexat peroral oder subkutan behandelt werden

Um einen positiven Einfluss auf den Krankheitsverlauf bei Patienten mit Rheumatoider Arthritis zu nehmen, ist die Compliance mit dem Basistherapeutikum Methotrexat unerlässlich. Therapietreue mit Methotrexat kann die Krankheitsprogression verhindern und irreversiblen Knochenerosionen vorbeugen. Methotrexat wird sowohl in subkutaner als auch in peroraler Applikationsform verordnet. Im Rahmen der vorliegenden Arbeit wurde die Compliance mit der Anwendung von Methotrexat Fertigspritzen und Tabletten mit einer elektronischen Messmethode (MEMS™) bestimmt. Hauptziel der Studie war die Bestimmung der Taking Compliance mit Methotrexat. Untersucht wurde hinsichtlich eines Unterschieds zwischen der Applikationsform und der Erkrankungsdauer. Daneben wurde die Dosing Compliance mit peroralem Methotrexat erfasst, sowie Einschätzungen der Patienten bezüglich der Compliance, Funktionskapazität, Lebensqualität und Zufriedenheit erhoben. Die Compliancestudie erfolgte in Kooperation mit dem Netzwerk ADAPTHERA. 74 Studienpatienten wurden 3 Gruppen zugeteilt: Gruppe 1 Methotrexat p.o.; Gruppe 2 Methotrexat s.c. und Erkrankungsdauer <24 Monate; Gruppe 3 Methotrexat s.c. und Erkrankungsdauer >24 Monate. Die Beobachtungsdauer betrug bei peroraler Applikationsform 9 Monate und bei subkutaner 6 Monate. Im Median wurde eine Taking und Dosing Compliance von 100% gemessen. Anhand der subjektiven Einschätzung der Patienten zur Funktionskapazität konnten geringe Einschränkungen für die Patienten im Alltag verzeichnet werden. 25% des Studienkollektivs litt unter einem reduzierten Wohlbefinden. Die Studie konnte zeigen, dass Patienten von einer frühzeitigen Therapie und einer hohen Compliancerate profitieren.

The Continuous Electrodeposition of Manganese

The object of this research was to produce a workable electrolytic cell for the continuous deposition of manganese from aqueous sulphate solutions and determine the critical factors in its oper­ation.

Pigment data set from the SeaWiFS Bio-optical Archive and Storage System (1961-1996)

The oceans play a critical role in the Earth's climate, but unfortunately, the extent of this role is only partially understood. One major obstacle is the difficulty associated with making high-quality, globally distributed observations, a feat that is nearly impossible using only ships and other ocean-based platforms. The data collected by satellite-borne ocean color instruments, however, provide environmental scientists a synoptic look at the productivity and variability of the Earth's oceans and atmosphere, respectively, on high-resolution temporal and spatial scales. Three such instruments, the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) onboard ORBIMAGE's OrbView-2 satellite, and two Moderate Resolution Imaging Spectroradiometers (MODIS) onboard the National Aeronautic and Space Administration's (NASA) Terra and Aqua satellites, have been in continuous operation since September 1997, February 2000, and June 2002, respectively. To facilitate the assembly of a suitably accurate data set for climate research, members of the NASA Sensor Intercomparison and Merger for Biological and Interdisciplinary Oceanic Studies (SIMBIOS) Project and SeaWiFS Project Offices devote significant attention to the calibration and validation of these and other ocean color instruments. This article briefly presents results from the SIMBIOS and SeaWiFS Project Office's (SSPO) satellite ocean color validation activities and describes the SeaWiFS Bio-optical Archive and Storage System (SeaBASS), a state-of-the-art system for archiving, cataloging, and distributing the in situ data used in these activities.

Modelado de materiales piezoeléctricos para aplicaciones de autoalimentación en entornos viales

Este proyecto continua con el estudio iniciado en los proyectos: Alimentación “Energy Harvesting” basada en fuentes piezoeléctricas, Alimentación autónoma: aplicación a fuente piezoeléctrica y Banco de pruebas para sistemas autoalimentados en aplicaciones viales, que se realizaron anteriormente. Este estudio se basa en la búsqueda de soluciones de alimentación Energy Harvesting centrados en fuentes piezoeléctricas. El objetivo de este estudio es conocer las posibilidades que pueden ofrecer los materiales piezoeléctricos para alimentación autónoma cuando son excitados por vehículos en diferentes circunstancias y entornos viales. Para la realización de este estudio se han utilizado señales provenientes del banco de ensayos, así como señales obtenidas de una instalación construida en un vial del Campus. Para poder realizar el estudio de los diversos materiales piezoeléctricos utilizados en este proyecto, se necesitan conocer las características de los modelos eléctricos. Para obtener estas características se ha diseñado un programa basado en LabView, este programa además puede modificar la señal para que simule las diversas circunstancias a las que pueden estar sometidos los diferentes materiales piezoeléctricos. En este estudio se ha tenido en cuenta la distancia de seguridad entre vehículos para diferentes velocidades y la posibilidad de poder amplificar la excitación que pueden recibir los diversos materiales. Utilizando el programa PSpice OrCAD® se realizan los diferentes modelos con el objetivo de observar el comportamiento de los materiales bajo diversas circunstancias. También se han utilizado varias topologías rectificadoras diferentes para poder comprobar en que situación se puede obtener la máxima tensión acumulada posible. Además también se ha evaluado la máxima potencia que puede entregar cada material en cada situación. Por ultimo se han realizado varias pruebas prácticas con el banco de ensayos para comprobar la acumulación energética real que se puede obtener de los materiales instalados en él. También se ha realizado el estudio de una aplicación práctica que sea capaz de alimentar pequeños circuitos o sensores de poco consumo. Abstract This Project goes on with the study started in the projects Feeding “Energy Harvesting” based on piezoelectric sources, independent feeding: application to piezoelectric source and testing bench to self fed systems in roads applications that were previously done. This study is based on the search of feeding solutions Energy Harvesting focus on piezoelectric sources. The aim of this study is know the different piezoelectric materials possibilities that can offer to independent feeding when different circumstances and road surroundings are excited by vehicles in. To develop this study several signals of the testing bench have been used and also signals get from an installation constructed on a Campus road. As far as the study of the different piezoelectric materials used in this project is concerned we should know the electrical models features. In order to obtain these characteristics a program based on LabView was designed, this program can modify the signal so that it simulates the diverse circumstances to which they can be put under the different piezoelectric materials. In this study I have bearded in mind the safe distance between vehicles for different speeds and the possibility of being able to amplify the excitation that can receive the diverse materials. Using the program PSpice OrCAD® the different models with the objective are made to observe the behaviour of the materials under diverse circumstances. Also several different rectifying topologies have been used to be able to verify the maximum overvoltage accumulated. In addition I have assessed the maximum power that can give each material in each situation. Last but not least different practical proofs with the testing bench have been done to check the actual energy accumulation that can be obtained from the materials installed on it. Also the study of a practical application has been made that is able to feed small circuits or low consumption sensor.

Desarrollo de una metodología de integración paisajística de las autopistas

El presente trabajo se enmarca dentro del proyecto “Operación de Autopistas Seguras, Inteligentes y Sostenibles (OASIS)”, cuyo principal objetivo es definir la autopista del futuro, aquella que en su operación presentará niveles notablemente altas de seguridad, servicio al usuario y sostenibilidad. Para lograrlo, uno de los parámetros a tener en cuenta es la conservación y optimización del paisaje por el que discurren. Esta tesis desarrolla una metodología de valoración del paisaje de las autopistas, aplicando dicha metodología a diversos tramos de las autopistas gestionadas por empresas del proyecto (OHL Concesiones, Iridium y Abertis). El estudio se ha llevado a cabo en más de 2.000 km de autopistas, identificando los diferentes paisajes vistos desde la carretera y elaborando un catálogo de fotografías digitalizadas y georreferenciadas de los paisajes; desarrollando y aplicando una novedosa metodología de valoración de la calidad del paisaje; determinando las diferencias entre el paisaje percibido desde las autopistas por medio de fotografías y mediante la utilización de mapas representativos de paisaje; identificando los elementos de diseño paisajístico (puentes, estaciones de servicio, etc.) y estableciendo alternativas para su mejor adecuación paisajística; y estimando el impacto que provocan estas infraestructuras al observarse desde fuera. Es de esperar que las conclusiones extraídas de este proyecto permitan una mejor integración paisajística de las autopistas del futuro, convirtiéndose en instrumentos para mostrar paisajes de mayor calidad, y reduciendo el impacto como elementos modificadores del territorio. Summary This work is within the framework of the project "Operation of Safe, Intelligent and Sustainable Highways (OASIS)," whose main objective is to define the highway of the future, which in its operation will present significantly high levels of safety, customer service and sustainability. To achieve this, one of the parameters to consider is landscape conservation and improvement along highways. This thesis develops a methodology for assessing the landscape of highways, applying the model to different stretches of highway managed by project companies (OHL Concessions, Iridium and Abertis). The study was carried out in more than 2.000 km of highways, identifying the different landscapes seen from the road and developing a catalog of digitized and georeferenced photographs of landscapes; developing and applying a new methodology for assessing the quality of the landscape; determining the differences between the landscape seen from highways through photographs and use of landscape maps; identifying the landscape design elements (bridges, service area, etc.) and providing alternatives for better landscape; and integration estimating the impact that cause these infrastructures when viewed from outside. It is expected that the conclusions extract from this project allow to better landscape integrate of the future highways, become instruments to show higher quality landscapes, reducing the impact as modifiers´ elements of the territory.

Efficient management of available technologies. Aplication to mining operations for industry supplies

Nowadays, processing Industry Sector is going through a series of changes, including right management and reduction of environmental affections. Any productive process which looks for sustainable management is incomplete if Cycle of Life of mineral resources sustainability is not taken into account. Raw materials for manufacturing are provided by mineral resources extraction processes, such as copper, aluminum, iron, gold, silver, silicon, titanium? Those elements are necessary for Mankind development and are obtained from the Earth through mineral extractive processes. Mineral extraction processes are operations which must take care about the environmental consequences. Extraction of huge volumes of rock for their transformation into raw materials for industry must be optimized to reduce ecological cost of the final product as l was possible. Reducing the ecological balance on a global scale has no sense to design an efficient manufacturing in secondary industry (transformation), if in first steps of the supply chain (extraction) impact exceeds the savings of resources in successive phases. Mining operations size suggests that it is an environmental aggressive activity, but precisely because of its great impact must be the first element to be considered. That idea implies that a new concept born: Reduce economical and environmental cost This work aims to make a reflection on the parameters that can be modified to reduce the energy cost of the process without an increasing in operational costs and always ensuring the same production capacity. That means minimize economic and environmental cost at same time. An efficient design of mining operation which has taken into account that idea does not implies an increasing of the operating cost. To get this objective is necessary to think in global operation view to make that all departments involved have common guidelines which make you think in the optimization of global energy costs. Sometimes a single operational cost must be increased to reduce global cost. This work makes a review through different design parameters of surface mining setting some key performance indicators (KPIs) which are estimated from an efficient point of view. Those KPIs can be included by HQE Policies as global indicators. The new concept developed is that a new criteria has to be applied in company policies: improve management, improving OPERATIONAL efficiency. That means, that is better to use current resources properly (machinery, equipment,?) than to replace them with new things but not used correctly. As a conclusion, through an efficient management of current technologies in each extractive operation an important reduction of the energy can be achieved looking at downstream in the process. That implies a lower energetic cost in the whole cycle of life in manufactured product.

Caracterización e instrumentación de sensores de ultrasonidos

El propósito de este proyecto de �fin de carrera es la caracterización e instrumentación de un sensor de ultrasonidos modelado por el tutor de este proyecto: Don César Briso Rodrí��guez. Una vez realizado el modelado de dicho sensor, simulando tanto sus caracter�í�sticas f�í�sicas, como sus caracterí��sticas eléctricas, se procede a la intrumentación y uso del mismo. La parte de intrumentaci�ón incluye tanto la electrónica que ser��á necesaria para la excitación del piezoeléctrico, en el modo de emisi�ón, como para la recepción de los pulsos el�éctricos generados por el sensor, como respuesta a los ecos recibidos, y su adecuación a niveles de señal correctos para la adquisici�ón, en el modo de escucha. Tras la adecuaci�ón de las señales para la adquisici�ón, éstas ser�án digitalizadas, tratadas y representadas por pantalla en un PC, a trav�es de una tarjeta de adquisición de datos por puerto USB encargada del muestreo de las señales de respuesta ya tratadas y su posterior enví��o al software de control y representaci�ón desarrollado en este proyecto. El entorno de usuario, el software de control de la tarjeta de adquisición y el software de tratamiento y representaci�ón se ha desarrollado con Visual Basic 2008 y las utilidades gr�áfi�cas de las librer��ías OpenGL. ABSTRACT The purpose of this project is to limit the characterization and implementation of an ultrasonic sensor modeled by Mr. C�ésar Briso Rodr��íguez. Once the sensor modeling by simulating physical characteristics and electrical characteristics, we proceed to the instrumentation and use. This section includes electronic instrumentation that would be necessary for the piezoelectric excitation in the emission mode and for receiving electrical pulses generated by the sensor in response to the received echoes, and matching signal levels right to acquire, in the reception mode. After the adjustment of the signals for the acquisition, these signals will be digitalized, processed and represented on the screen on a PC through a data acquisition card by USB port. Acquisition card is able to sample the response signals and transmit the samples to representation and control software developed in this project. The user interface, the acquisition card control software and processing and representation software has been developed with Visual Basic 2008 and OpenGL graphical libraries.

Efecto del Cross-talk en la respuesta de un Transductor Ultrasónico tipo PZT

El presente trabajo de tesis investiga el efecto del fenómeno conocido como “Cross-talk” generado por el modo lateral de vibración, en la respuesta de un transductor ultrasónico formado por un arreglo de elementos piezoeléctricos tipo PZT (Zircanato Titanato de Plomo), la investigación se lleva a cabo desde el punto de vista de la naturaleza física de este efecto, así como de los parámetros asociados al mismo, así como un análisis del efecto del “Cross-talk” en la respuesta del transductor, formado por arreglos de elementos piezoeléctricos. Diversas investigaciones han abordado el fenómeno del “Cross-talk” y de sus efectos en la respuesta de los transductores, estos se han enfocado principalmente al modo espesor (thickness) de vibración. Sin embargo no ha habido un estudio a fondo para el estudio de este fenómeno en el modo lateral de vibración tema de interés de este trabajo de tesis. Este trabajo incluye simulaciones del fenómeno del “Cross-talk” mediante el método de los elementos finitos (MEF), así como la construcción de un transductor tipo matricial (arrray) de 2x3 elementos, en el que fueron realizadas las mediciones físicas del fenómeno. El trabajo abarca un estudio comparativo entre las simulaciones y las mediciones realizadas en el transductor, considerando que las cerámicas del transductor están montadas sobre diferentes materiales (backing) en donde la propagación de la energía emitida por las cerámicas piezoeléctricas provoca un mayor o menor grado de “Cross-talk” dependiendo de la velocidad en que se propaga dicha energía. Esta investigación también llevó a cabo el estudio del efecto del “Cross-talk” en el patrón de radiación que emite el arreglo de elementos piezoeléctricos, siendo este patrón de radiación un factor importante en la respuesta del transductor, motivo por el cual se realizó un análisis de cómo se ve afectado este patrón bajo la influencia del fenómeno del “Cross-talk”. Como ya se mencionó debido a la falta de un estudio a profundidad del fenómeno del “Cross-talk” en el modo lateral, la contribución del presente trabajo es importante ya que se enfoca al modo lateral de vibración de los elementos piezoeléctricos del arreglo. En particular se desarrollo una ecuación que permite cuantificar el fenómeno del “Cross-talk” y visualizar sus efectos en el arreglo. Derivando de este estudio se concluye que el fenómeno del “Cross-talk” generado por el modo lateral de vibración tiene un efecto significativo en la respuesta de los diferentes transductores matriciales considerados. ABSTRACT This thesis investigates the effect of the phenomenon known as crosstalk from the point of view of its physical nature and the elements that lead to the formation of this phenomenon to an analysis of how it may affect the performance of the ultrasonic transducer. This phenomenon occurs primarily in matrix arrays and this phenomenon is magnified by certain factors causing serious problems in the performance of a transducer. Researchers have addressed the phenomenon of crosstalk and their effects on the response of these transducers. They have mainly focused in the thickness vibration mode, and there has been no comprehensive study of this phenomenon in the lateral vibration mode, issue of interest of this thesis. This work includes simulations of the crosstalk phenomenon using the finite element method (FEM), and the construction of a matrix type transducer (array) of 2x3 elements, in which physical measurements were made. The work includes a comparative study between simulations and measurements in the transducer, whereas the ceramic transducer are mounted on different materials (backing) where the spread of the energy emitted by the piezoelectric ceramic causes a greater or lesser degree of crosstalk depending on the speed at which this energy spreads. This research also carried out the study of the effect of the crosstalk in the radiation pattern emitted by the piezoelectric array. The radiation pattern is an important factor in the response of the transducer that is why we conducted an analysis of how this pattern is affected under the influence of the crosstalk phenomenon. As mentioned before because of the lack of an in-depth study of the crosstalk phenomenon in the lateral vibration mode, the contribution of this work is important because it focuses in this vibration mode of the piezoelectric elements in the array. In particular, an equation was developed to quantify the crosstalk phenomenon and to see its effects in the array. Deriving from this study it is possible to conclude that the crosstalk phenomenon generated by the lateral vibration mode has a significant effect on the response of the different matrix transducers considered in this work.

Boolean logic device done with DFB laser diode

We present simulation results on how power output-input characteristic Instability in Distributed FeedBack -DFB semiconductor laser diode SLA can be employed to implemented Boolean logic device. Two configurations of DFB Laser diode under external optical injection, either in the transmission or in the reflective mode of operation, is used to implement different Optical Logic Cells (OLCs), called the Q- and the P-Device OLCs. The external optical injection correspond to two inputs data plus a cw control signal that allows to choose the Boolean logic function to be implement. DFB laser diode parameters are choosing to obtain an output-input characteristic with the values desired. The desired values are mainly the on-off contrast and switching power, conforming shape of hysteretic cycle. Two DFB lasers in cascade, one working in transmission operation and the other one in reflective operation, allows designing an inputoutput characteristic based on the same respond of a self-electrooptic effect device is obtained. Input power for a bit'T' is 35 uW(70uW) and a bit "0" is zero for all the Boolean function to be execute. Device control signal range to choose the logic function is 0-140 uW (280 uW). Q-device (P-device)

A reliable support tool for monitoring, testing and debugging wireless sensor cookie nodes

In this work a WSN Support Tool for developing, testing, monitoring and debugging new application prototypes in a reliable and robust way is proposed, by combining a Hardware -Software Integration Platform with the implementation of a parallel communication channel that helps users to interact to the experiments in runtime without interfering in the operation of the wireless network. As a pre-deployment tool, prototypes can be validated in a real environment before implementing them in the final application, aiming to increase the effectiveness and efficiency of the technology. This infrastructure is the support of CookieLab: a WSN testbed based on the Cookie Nodes Platform.

Design, development and construction of an outdoor testing facility for semi-transparent photovoltaic modules

Building-integrated Photovoltaics (BIPV) is one of the most promising technologies enabling buildings to generate on-site part of their electricity needs while performing architectural functionalities. A clear example of BIPV products consists of semi-transparent photovoltaic modules (STPV), designed to replace the conventional glazing solutions in building façades. Accordingly, the active building envelope is required to perform multiple requirements such as provide solar shading to avoid overheating, supply solar gains and thermal insulation to reduce heat loads and improve daylight utilization. To date, various studies into STPV systems have focused on their energy performance based on existing simulation programs, or on the modelling, normally validated by limited experimental data, of the STPV modules thermal behaviour. Taking into account that very limited experimental research has been conducted on the energy performance of STPV elements and that the characterization in real operation conditions is necessary to promote an energetically efficient integration of this technology in the building envelope, an outdoor testing facility has been designed, developed and built at the Solar Energy Institute of the Technical University of Madrid. In this work, the methodology used in the definition of the testing facility, its capability and limitations are presented and discussed.

Diagnostics of classical and dusty plasmas w ith collecting and emissive langmuir probes = Diagnosis de plasmas clásicos y granulares mediante sondas colectoras y emisoras de Langmuir

Las sondas eléctricas se emplean habitualmente en la diagnosis de plasmas. La presente tesis aborda la operación de las sondas colectoras y emisoras de Langmuir en plasmas fríos de baja densidad. El estudio se ha centrado en la determinación del potencial de plasma, Vsp, mediante el potencial flotante de una sonda emisora. Esta técnica consiste en la medida del potencial de la sonda correspondiente a la condición de corriente neta igual a cero, el cual se denomina potencial flotante, VF. Este potencial se desplaza hacia el potencial del plasma según aumenta la emisión termoiónica de la sonda, hasta que se satura cerca de Vsp. Los experimentos llevados a cabo en la pluma de plasma de un motor iónico y en un plasma de descarga de glow muestran que la corriente de electrones termoiónicos es mayor que la corriente de electrones recogidos para una sonda polarizada por debajo del potencial del plasma, resultado inconsistente con la teoría tradicionalmente aceptada. Para investigar estos resultados se ha introducido el parámetro R, definido como el cociente entre la corriente de electrones emitidos y recogidos por la sonda. Este parámetro, que está relacionado con la diferencia de potencial VF - Vsp, también es útil para la descripción de los modos de operación de la sonda emisora (débil, fuerte y más allá del fuerte). Los resultados experimentales evidencian que, al contrario de lo que indica la teoría, R es mayor que la unidad. Esta discrepancia se puede solucionar introduciendo una población efectiva de electrones. Con dicha población, el nuevo modelo para la corriente total de la sonda reproduce los datos experimentales. El origen de este grupo electrónico es todavía una cuestión abierta, pero podría estar originada por una nueva estructura de potencial cerca de la sonda cuando ésta trabaja en el régimen de emisión fuerte. Para explicar dicha estructura de potencial, se propone un modelo unidimensional compuesto por un mínimo de potencial cerca de la superficie de la sonda. El análisis numérico indica que este pozo de potencial aparece para muy altas temperaturas de la sonda, reduciendo la cantidad de electrones emitidos que alcanzan el plasma y evitando así cualquier posible perturbación de éste. Los aspectos experimentales involucrados en el método del potencial flotante también se han estudiado, incluyendo cuestiones como las diferentes técnicas de obtención del VF, el cociente señal-ruido, el acoplamiento de la señal de los equipos utilizados para la obtención de las curvas I-V o la evidencia experimental de los diferentes modos de operación de la sonda. Estas evidencias empíricas se encuentran en todos los aspectos de operación de la sonda: la recolección de electrones, el potencial flotante, la precisión en las curvas I-V y la emisión electrónica. Ésta última también se estudia en la tesis, debido a que un fenómeno de super emisión tiene lugar en el régimen de emisión fuerte. En este modo de operación, las medidas experimentales indican que las corrientes termoiónicas de electrones son mayores que aquéllas predichas por la ecuación de Richardson-Dushman clásica. Por último, la diagnosis de plasmas usando sondas eléctrica bajo presencia de granos de polvo (plasmas granulares) en plasmas fríos de baja densidad también se ha estudiado, mediante la aplicación numérica de la técnica del potencial flotante de la sonda emisora en un plasma no convencional. Los resultados apuntan a que el potencial flotante de una sonda emisora se vería afectado por altas densidades de polvo o grandes partículas. ABSTRACT Electric probes are widely employed for plasma diagnostics. This dissertation concerns the operation of collecting and emissive Langmuir probes in low density cold plasmas. The study is focused on the determination of the plasma potential, Vsp, by means of the floating potential of emissive probes. This technique consists of the measurement of the probe potential, corresponding to the zero net probe current, which is the so-called floating potential, VF . This potential displaces towards the plasma potential as the thermionic electron emission increases, until it saturates near Vsp. Experiments carried out in the plasma plume of an ion thruster and in a glow discharge plasma show the thermionic electron current of the emissive Langmuir probe is higher than the collected electron current, for a probe with a bias potential below Vsp, which is inconsistent with the traditional accepted theory. To investigate these results, a parameter R is introduced as the ratio between the emitted and the collected electron current. This parameter, which is related to the difference VF - Vsp, is also useful for the description of the operation modes of the emissive Langmuir probe (weak, strong and beyond strong). The experimental results give an inconsistency of R > 1, which is solved by a modification of the theory for emissive probes, with the introduction of an effective electron population. With this new electron group, the new model for the total probe current agrees with the experimental data. The origin of this electron group remains an open question, but it might be originated by a new potential structure near the emissive probe when it operates in the strong emission regime. A simple one-dimension model composed by a minimum of potential near the probe surface is discussed for strongly emitting emissive probes. The results indicate that this complex potential structure appears for very high probe temperatures and the potential well might reduce the emitted electrons population reaching the plasma bulk. The experimental issues involved in the floating potential method are also studied, as the different obtaining techniques of VF, the signal-to-noise ratio, the signal coupling of the I-V curve measurement system or the experimental evidence of the probe operation modes. These empirical proofs concern all the probe operation aspects: the electron collection, the floating potential, the I-V curve accuracy as well as the electron emission. This last issue is also investigated in this dissertation, because a super emission takes place in the strong emission regime. In this operation mode, the experimental results indicate that the thermionic electron currents might be higher than those predicted by the classical Richardson-Dushman equation. Finally, plasma diagnosis using electric probes in the presence of dust grains (dusty plasmas) in low density cold plasmas is also addressed. The application of the floating potential technique of the emissive probe in a non-conventional complex plasma is numerically investigated, whose results point out the floating potential of the emissive probe might be shifted for high dust density or large dust particles.

Estudio de la fiabilidad de diodos LEDs rojos mediante ensayos acelerados

El objetivo de este Proyecto Final de Carrera es la realización de un ensayo de fiabilidad de componentes electrónicos, más concretamente de diodos LED, con el fin de estudiar su comportamiento a lo largo del tiempo de vida. Debido a la larga duración de los LEDs, un ensayo de este tipo podría durar años, por lo que es necesario realizar un ensayo acelerado que acorte significativamente el tiempo del experimento, para ello, han de someterse a esfuerzos mayores que en condiciones normales de funcionamiento. En la actualidad, los LEDs son usados en infinidad de aplicaciones, debido a sus múltiples ventajas respecto a otros sistemas de iluminación o señalización convencionales. En numerosos casos se utilizan en el exterior, soportando cambios de temperaturas y de humedad elevados, de ahí, la importancia de realizar ensayos de fiabilidad, que muestren sus posibles causas de fallo, los efectos que producen estos fallos y los aspectos de diseño, fabricación y mantenimiento que puedan afectarles. Como consecuencia del envejecimiento de los LEDs, pueden mostrar una reducción en el flujo luminoso y un empeoramiento de las propiedades cromáticas. Los LEDs utilizados en este Proyecto son de AlInGaP, rojos, de alta luminosidad. Para acelerar el ensayo, se utilizará una cámara climática que simule unas condiciones ambientales determinadas, en concreto, 85º C y 85% HR. Además, se realiza una monitorización periódica, siendo necesaria la utilización de un sistema automático de medida diseñado en LabVIEW, el cual, de manera simultánea realizará medidas y gestionará la inyección de corriente a los LEDs mientras se encuentren en el interior de la cámara climática. Se fabrican dos placas con 4 tiras de LEDs para inyectar un nivel de corriente diferente en cada una y así poder comparar la degradación en función de este parámetro. Fuera de la cámara climática se van a medir las curvas características de tensióncorriente de cada LED a una temperatura ambiente constante, fijada por un módulo Peltier. También se realizarán medidas de potencia luminosa y de espectro de emisión. Se analizarán los resultados obtenidos de cada una de las medidas y se realizará un estudio de fiabilidad y del proceso de degradación sufrido por los LEDs. Este PFC se puede dividir en las siguientes fases de trabajo, siendo el ensayo la parte más larga en el tiempo: · Búsqueda de bibliografía, documentación y normas aplicables. · Familiarización con los equipos y software, estudiando el manejo y funcionamiento de la cámara climática temperatura-humedad y el software a aplicar (LabVIEW y software del espectrómetro). · Desarrollo del hardware y sistemas necesarios para la realización del ensayo. · Realización del ensayo. · Análisis de resultados. ABSTRACT. The objective of this end of degree project is conducting an essay reliability of electronic components, more concretely LEDs, in order to study their behavior throughout its lifespan. Due to the long duration of the LEDs, a essay of this type could last for years, so it is necessary to perform an accelerated essay which significantly shorten the time of the experiment, testing should be subjected to greater efforts than in normal operation. Today, LEDs are used in many applications due to its many advantages over other conventional lighting systems or signaling. In numerous cases are used on the outside, enduring high changes in temperature and humidity, hence the importance of reliability essays, showing the possible causes of failure, the effects produced by these failures and aspects of design, manufacturing and maintenance that may affect them. As a result of the ageing of the LEDs, they may show a reduction in light output and a worsening of the chromatic properties. The LEDs used in this project are AlInGaP, red and high brightness. To speed up the essay will be used a climatic chamber to simulate specific environmental conditions, specifically 85 ° C and 85 % RH. In addition, is pe rformed a periodic monitoring using an automatic measurement system designed in LabVIEW , which , simultaneously will performed measurements and will manage the injection current to the LEDs while are inside of the climatic chamber. 4 strips of LEDs are created to inject a different level of current in each, so can compare the degradation in terms of this parameter. Out of the climatic chamber are obtained the characteristic curves of voltage-current of each LED at a constant room temperature, set by a Peltier module. Also, measures light power and the emitted spectrum. The results of each of the measures and a reliability study and degradation suffered by the LEDs will be discussed. This PFC can be divided into the following steps, the essay being the longest part: • Search bibliography, documentation and standards. • Familiarization with equipment and software, studying the management and the operation of the temperature-humidity environmental chamber and applying software (LabVIEW applications and spectrometer software). • Development of hardware and systems necessary for the conduct of the essay. • Carrying out the essay. • Analysis of results.

SOPHIA CPV module round robin: power rating at CSOC

Within the European funded project SOPHIA, a Round Robin measurement on CPV module has been initiated. Seven different test laboratories located in Europe between 48°N and 37°N perform measurements of four SOITEC CPV modules. The modules are electrically characterized with different measurement equipment under various climatic conditions. One pyrheliometer and one spectral sensor based on component cells are shipped together with the modules. This ensures that the irradiance and spectrum, two factors with high impact on CPV module performance, are measured with the identical equipment at each site. The round robin activity is performed in closeco-operation with the IEC TC82 WG7 power rating team in order to support the work on the CPV module power rating draft standard 62670-3. The resultingrated module power outputs at CSOC (Concentrator Standard Operating Conditions) are compared amongst the power rating methods and amongst the test labs. In this manner, a deviation in rated power output between different test labs and power rating methods is determined.