Ultrasonic wave reflection measurements on self-compacting pastes and concretes

The objective of this study was to extend the use of combined longitudinal (P-wave) and shear (S-wave) ultrasonic wave reflection (UWR) to monitor the setting and stiffening of self-compacting pastes and concretes. An additional objective was to interpret the UWR responses of various modified cement pastes. A polymeric buffer with acoustic impedance close to that of cement paste, high impact polystyrene, was chosen to obtain sensitive results from the early hydration period. Criteria for initial and final set developed by our group in a prior study were used to compute setting times by UWR. UWR results were compared with standard penetration measurements. Stiffening behavior and setting times for normal cement pastes, pastes modified with mineral and chemical admixtures, self-compacting pastes, and concretes were explored using penetration resistance, S-wave and P-wave reflection. All three methods showed that set times of pastes varied linearly with w/c, that superplasticizer and fly ash delayed the set times of pastes, and that differences in w/cm, sp/cm, and fa/cm could be detected. Final set times determined from UWR correlated well with those from penetration resistance. Initial set times from S-wave reflection did not correlate very well with those from penetration resistance. Final set times from P-wave and S-wave reflection were roughly the same. Pastes with different chemical admixtures were tested, and the effects of these admixtures on stiffening were determined using UWR. Self-compacting concretes were studied using UWR, and their response and setting times were largely similar to that of corresponding self-compacting pastes. The P-wave reflection response was explored in detail, and the phenomenon of partial debonding and the factors affecting it were explained. Partial debonding is probably caused by autogenous shrinkage at final set, and was controlled and limited by water. The extent of partial debonding was higher with the transducers placed on the side as opposed to the bottom, and the S-wave transducer seemed to promote debonding in the P-wave reflection, whereas the P-wave transducer seemed to reduce debonding in the S-wave reflection. Simultaneous formwork pressure testing and UWR were performed; however, no clear correlation was seen between the two properties.

Design and construction of a two dimensional duct equipped with a wave generator and a variable coastal slope and an ocean wave energy conversion system (OWC)

The aims of this thesis were evaluation the type of wave channel, wave current, and effect of some parameters on them and identification and comparison between types of wave maker in laboratory situations. In this study, designing and making of two dimension channels (flume) and wave maker for experiment son the marine buoy, marine building and energy conversion systems were also investigated. In current research, the physical relation between pump and pumpage and the designing of current making in flume were evaluated. The related calculation for steel building, channels beside glasses and also equations of wave maker plate movement, power of motor and absorb wave(co astal slope) were calculated. In continue of this study, the servo motor was designed and applied for moving of wave maker’s plate. One Ball Screw Leaner was used for having better movement mechanisms of equipment and convert of the around movement to linear movement. The Programmable Logic Controller (PLC) was also used for control of wave maker system. The studies were explained type of ocean energies and energy conversion systems. In another part of this research, the systems of energy resistance in special way of Oscillating Water Column (OWC) were explained and one sample model was designed and applied in hydrolic channel at the Sheikh Bahaii building in Azad University, Science and Research Branch. The dimensions of designed flume was considered at 16 1.98 0. 57 m which had ability to provide regular waves as well as irregular waves with little changing on the control system. The ability of making waves was evaluated in our designed channel and the results were showed that all of the calculation in designed flume was correct. The mean of error between our results and theory calculation was conducted 7%, which was showed the well result in this situation. With evaluating of designed OWC model and considering of changes in the some part of system, one bigger sample of this model can be used for designing the energy conversion system model. The obtained results showed that the best form for chamber in exit position of system, were zero degree (0) in angle for moving below part, forty and five (45) degree in front wall of system and the moving forward of front wall keep in two times of height of wave.

The Becker-Döring equations with monomer input, competition and inhibition

We investigate the Becker-Döring model of nucleation with three generalisations; an input of monomer, an input of inhibitor and finally, we allow the monomers to form two morphologies of cluster. We assume size-independent aggregation and fragmentation rates. Initially we consider the problem of constant monomer input and determine the steady-state solution approached in the large-time limit, and the manner in which it is approached. Secondly, in addition to a constant input of monomer we allow a constant input of inhibitor, which prevents clusters growing any larger and this removes them from the kinetics of the process; the inhibitor is consumed in the action of poisoning a cluster. We determine a critical ratio of poison to monomer input below which the cluster concentrations tend to a non-zero steady-state solution and the poison concentration tends to a finite value. Above the critical input ratio, the concentrations of all cluster sizes tend to zero and the poison concentration grows without limit. In both cases the solution in the large-time limit is determined. Finally we consider a model where monomers form two morphologies, but the inhibitor only acts on one morphology. Four cases are identified, depending on the relative poison to monomer input rates and the relative thermodynamic stability. In each case we determine the final cluster distribution and poison concentration. We find that poisoning the less stable cluster type can have a significant impact on the structure of the more stable cluster distribution; a counter-intuitive result. All results are shown to agree with numerical simulation.

Wave climate in the Arctic 1992-2014: seasonality and trends

Over the past decade, the diminishing Arctic sea ice has impacted the wave field, which depends on the ice-free ocean and wind. This study characterizes the wave climate in the Arctic spanning 1992–2014 from a merged altimeter data set and a wave hindcast that uses CFSR winds and ice concentrations from satellites as input. The model performs well, verified by the altimeters, and is relatively consistent for climate studies. The wave seasonality and extremes are linked to the ice coverage, wind strength, and wind direction, creating distinct features in the wind seas and swells. The altimeters and model show that the reduction of sea ice coverage causes increasing wave heights instead of the wind. However, trends are convoluted by interannual climate oscillations like the North Atlantic Oscillation (NAO) and Pacific Decadal Oscillation. In the Nordic Greenland Sea the NAO influences the decreasing wind speeds and wave heights. Swells are becoming more prevalent and wind-sea steepness is declining. The satellite data show the sea ice minimum occurs later in fall when the wind speeds increase. This creates more favorable conditions for wave development. Therefore we expect the ice freeze-up in fall to be the most critical season in the Arctic and small changes in ice cover, wind speeds, and wave heights can have large impacts to the evolution of the sea ice throughout the year. It is inconclusive how important wave–ice processes are within the climate system, but selected events suggest the importance of waves within the marginal ice zone.

Gravimetric and density profiling using the combination of surface acoustic waves and neutron reflectivity

A new approach is described herein, where neutron reflectivity measurements that probe changes in the density profile of thin films as they absorb material from the gas phase have been combined with a Love wave based gravimetric assay that measures the mass of absorbed material. This combination of techniques not only determines the spatial distribution of absorbed molecules, but also reveals the amount of void space within the thin film (a quantity that can be difficult to assess using neutron reflectivity measurements alone). The uptake of organic solvent vapours into spun cast films of polystyrene has been used as a model system with a view to this method having the potential for extension to the study of other systems. These could include, for example, humidity sensors, hydrogel swelling, biomolecule adsorption or transformations of electroactive and chemically reactive thin films. This is the first ever demonstration of combined neutron reflectivity and Love wave-based gravimetry and the experimental caveats, limitations and scope of the method are explored and discussed in detail.

Dopamine and visually regulated eye growth in chick

Retinal image properties such as contrast and spatial frequency play important roles in the development of normal vision. For example, visual environments comprised solely of low contrast and/or low spatial frequencies induce myopia. The visual image is processed by the retina and it then locally controls eye growth. In terms of the retinal neurotransmitters that link visual stimuli to eye growth, there is strong evidence to suggest involvement of the retinal dopamine (DA) system. For example, effectively increasing retinal DA levels by using DA agonists can suppress the development of form-deprivation myopia (FDM). However, whether visual feedback controls eye growth by modulating retinal DA release, and/or some other factors, is still being elucidated. This thesis is chiefly concerned with the relationship between the dopaminergic system and retinal image properties in eye growth control. More specifically, whether the amount of retinal DA release reduces as the complexity of the image degrades was determined. For example, we investigated whether the level of retinal DA release decreased as image contrast decreased. In addition, the effects of spatial frequency, spatial energy distribution slope, and spatial phase on retinal DA release and eye growth were examined. When chicks were 8-days-old, a cone-lens imaging system was applied monocularly (+30 D, 3.3 cm cone). A short-term treatment period (6 hr) and a longer-term treatment period (4.5 days) were used. The short-term treatment tests for the acute reduction in DA release by the visual stimulus, as is seen with diffusers and lenses, whereas the 4.5 day point tests for reduction in DA release after more prolonged exposure to the visual stimulus. In the contrast study, 1.35 cyc/deg square wave grating targets of 95%, 67%, 45%, 12% or 4.2% contrast were used. Blank (0% contrast) targets were included for comparison. In the spatial frequency study, both sine and square wave grating targets with either 0.017 cyc/deg and 0.13 cyc/deg fundamental spatial frequencies and 95% contrast were used. In the spectral slope study, 30% root-mean-squared (RMS) contrast fractal noise targets with spectral fall-off of 1/f0.5, 1/f and 1/f2 were used. In the spatial alignment study, a structured Maltese cross (MX) target, a structured circular patterned (C) target and the scrambled versions of these two targets (SMX and SC) were used. Each treatment group comprised 6 chicks for ocular biometry (refraction and ocular dimension measurement) and 4 for analysis of retinal DA release. Vitreal dihydroxyphenylacetic acid (DOPAC) was analysed through ion-paired reversed phase high performance liquid chromatography with electrochemical detection (HPLC-ED), as a measure of retinal DA release. For the comparison between retinal DA release and eye growth, large reductions in retinal DA release possibly due to the decreased light level inside the cone-lens imaging system were observed across all treated eyes while only those exposed to low contrast, low spatial frequency sine wave grating, 1/f2, C and SC targets had myopic shifts in refraction. Amongst these treatment groups, no acute effect was observed and longer-term effects were only found in the low contrast and 1/f2 groups. These findings suggest that retinal DA release does not causally link visual stimuli properties to eye growth, and these target induced changes in refractive development are not dependent on the level of retinal DA release. Retinal dopaminergic cells might be affected indirectly via other retinal cells that immediately respond to changes in the image contrast of the retinal image.

Characteristics and predictors of high-range speeding offenders

This paper examines an aspect of the data taken from a larger study evaluating the effect of speeding penalty changes on speeding recidivism in Queensland. Traffic offence data from May 1996 to August 2007 were provided to the research team for two cohorts of offenders: individuals who committed a speeding offence in May 2001; and individuals who committed a speeding offence in May 2003. Data included details of the offenders’ index offence, previous and subsequent traffic offences (speeding and other) and their demographic characteristics. Using this data the aim of this component of the research was to use demographic data and the previous traffic offences of these individuals to explore the characteristics and predictors of high-range speeding offenders. High-range offenders were identified as those individuals who committed two or more speeding offences with a recorded speed of 30 km/hr or more above the speed limit. For the purposes of comparison, low-range offenders (committed one speeding offence in the time-frame and that offence was less than 15 km/hr over the speed limit) and mid-range offenders (all other offenders) were identified. Using Chi-square and logistic regression analyses, characteristics and predictors of high-range speeding offenders were identified. The implications and limitations of this study are also discussed.

Limits of spherical blur determined with an adaptive optics mirror

We extended an earlier study (Vision Research, 45, 1967–1974, 2005) in which we investigated limits at which induced blur of letter targets becomes noticeable, troublesome and objectionable. Here we used a deformable adaptive optics mirror to vary spherical defocus for conditions of a white background with correction of astigmatism; a white background with reduction of all aberrations other than defocus; and a monochromatic background with reduction of all aberrations other than defocus. We used seven cyclopleged subjects, lines of three high-contrast letters as targets, 3–6 mm artificial pupils, and 0.1–0.6 logMAR letter sizes. Subjects used a method of adjustment to control the defocus component of the mirror to set the 'just noticeable', 'just troublesome' and 'just objectionable' defocus levels. For the white-no adaptive optics condition combined with 0.1 logMAR letter size, mean 'noticeable' blur limits were ±0.30, ±0.24 and ±0.23 D at 3, 4 and 6 mm pupils, respectively. White-adaptive optics and monochromatic-adaptive optics conditions reduced blur limits by 8% and 20%, respectively. Increasing pupil size from 3–6 mm decreased blur limits by 29%, and increasing letter size increased blur limits by 79%. Ratios of troublesome to noticeable, and of objectionable to noticeable, blur limits were 1.9 and 2.7 times, respectively. The study shows that the deformable mirror can be used to vary defocus in vision experiments. Overall, the results of noticeable, troublesome and objectionable blur agreed well with those of the previous study. Attempting to reduce higher-order aberrations or chromatic aberrations, reduced blur limits to only a small extent.

Personalised ontology learning and mining for web information gathering

Over the last decade, the rapid growth and adoption of the World Wide Web has further exacerbated user needs for e±cient mechanisms for information and knowledge location, selection, and retrieval. How to gather useful and meaningful information from the Web becomes challenging to users. The capture of user information needs is key to delivering users' desired information, and user pro¯les can help to capture information needs. However, e®ectively acquiring user pro¯les is di±cult. It is argued that if user background knowledge can be speci¯ed by ontolo- gies, more accurate user pro¯les can be acquired and thus information needs can be captured e®ectively. Web users implicitly possess concept models that are obtained from their experience and education, and use the concept models in information gathering. Prior to this work, much research has attempted to use ontologies to specify user background knowledge and user concept models. However, these works have a drawback in that they cannot move beyond the subsumption of super - and sub-class structure to emphasising the speci¯c se- mantic relations in a single computational model. This has also been a challenge for years in the knowledge engineering community. Thus, using ontologies to represent user concept models and to acquire user pro¯les remains an unsolved problem in personalised Web information gathering and knowledge engineering. In this thesis, an ontology learning and mining model is proposed to acquire user pro¯les for personalised Web information gathering. The proposed compu- tational model emphasises the speci¯c is-a and part-of semantic relations in one computational model. The world knowledge and users' Local Instance Reposito- ries are used to attempt to discover and specify user background knowledge. From a world knowledge base, personalised ontologies are constructed by adopting au- tomatic or semi-automatic techniques to extract user interest concepts, focusing on user information needs. A multidimensional ontology mining method, Speci- ¯city and Exhaustivity, is also introduced in this thesis for analysing the user background knowledge discovered and speci¯ed in user personalised ontologies. The ontology learning and mining model is evaluated by comparing with human- based and state-of-the-art computational models in experiments, using a large, standard data set. The experimental results are promising for evaluation. The proposed ontology learning and mining model in this thesis helps to develop a better understanding of user pro¯le acquisition, thus providing better design of personalised Web information gathering systems. The contributions are increasingly signi¯cant, given both the rapid explosion of Web information in recent years and today's accessibility to the Internet and the full text world.

Vibration of ship structures and its control

Noise and vibration in complex ship structures are becoming a prominent issue for ship building industry and ship companies due to the constant demand of building faster ships of lighter weight, and the stringent noise and libration regulation of the industry. In order to retain the full benefit of building faster ships without compromising too much on ride comfort and safety, noise and vibration control needs to be implemented. Due to the complexity of ship structures, the coupling of different wave types and multiple wave propagation paths, active control of global hull modes is difficult to implement and very expensive. Traditional passive control such as adding damping materials is only effective in the high frequency range. However, most severe damage to ship structures is caused by large structural deformation of hull structures and high dynamic stress concentration at low frequencies. The most discomfort and fatigue of passengers and the crew onboard ships is also due to the low frequency noise and vibration. Innovative approaches are therefore, required to attenuate the noise and vibration at low frequencies. This book was developed from several specialized research topics on vibration and vibration control of ship structures, mostly from the author's own PhD work at the University of Western Australia. The book aims to provide a better understanding of vibration characteristics of ribbed plate structures, plate/plate coupled structures and the mechanism governing wave propagation and attenuation in periodic and irregular ribbed structures as well as in complex ship structures. The book is designed to be a reference book for ship builders, vibro-acoustic engineers and researchers. The author also hopes that the book can stimulate more exciting future work in this area of research. It is the author's humble desire that the book can be some use for those who purchase it. This book is divided into eight chapters. Each chapter focuses on providing solution to address a particular issue on vibration problems of ship structures. A brief summary of each chapter is given in the general introduction. All chapters are inter-dependent to each other to form an integration volume on the subject of vibration and vibration control of ship structures and alike. I am in debt to many people in completing this work. In particular, I would like to thank Professor J. Pan, Dr N.H. Farag, Dr K. Sum and many others from the University of Western Australia for useful advices and helps during my times at the University and beyond. I would also like to thank my wife, Miaoling Wang, my children, Anita, Sophia and Angela Lin, for their sacrifice and continuing supports to make this work possible. Financial supports from Australian Research Council, Australian Defense Science and Technology Organization and Strategic Marine Pty Ltd at Western Australia for this work is gratefully acknowledged.

Do strategy choices matter for nascent firms? A study on effectuation and causation impacts on new ventures outcomes

Principal Topic : Nascent entrepreneurship has drawn the attention of scholars in the last few years (Davidsson, 2006, Wagner, 2004). However, most studies have asked why firms are created focussing on questions such as what are the characteristics (Delmar and Davidsson, 2000) and motivations (Carter, Gartner, Shaver & Reynolds, 2004) of nascent entrepreneurs, or what are the success factors in venture creation (Davidsson & Honig; 2003; Delmar and Shane, 2004). In contrast, the question of how companies emerge is still in its infancy. On a theoretical side, effectuation, developed by Sarasvathy (2001) offers one view of the strategies that may be at work during the venture creation process. Causation, the theorized inverse to effectuation, may be described as a rational reasoning method to create a company. After a comprehensive market analysis to discover opportunities, the entrepreneur will select the alternative with the higher expected return and implement it through the use of a business plan. In contrast, effectuation suggests that the future entrepreneur will develop her new venture in a more iterative way by selecting possibilities through flexibility and interaction with the market, affordability of loss of resources and time invested, development of pre-commitments and alliances from stakeholders. Another contrasting point is that causation is ''goal driven'' while an effectual approach is ''mean driven'' (Sarasvathy, 2001) One of the predictions of effectuation theory is effectuation is more likely to be used by entrepreneurs early in the venture creation process (Sarasvathy, 2001). However, this temporal aspect and the impact of the effectuation strategy on the venture outcomes has so far not been systematically and empirically tested on large samples. The reason behind this research gap is twofold. Firstly, few studies collect longitudinal data on emerging ventures at an early enough stage of development to avoid severe survivor bias. Second, the studies that collect such data have not included validated measures of effectuation. The research we are conducting attempts to partially fill this gap by combining an empirical investigation on a large sample of nascent and young firms with the effectuation/causation continuum as a basis (Sarasvathy, 2001). The objectives are to understand the strategies used by the firms during the creation process and measure their impacts on the firm outcomes. Methodology/Key Propositions : This study draws its data from the first wave of the CAUSEE project where 28,383 Australian households were randomly contacted by phone using a specific methodology to capture emerging firms (Davidsson, Steffens, Gordon, Reynolds, 2008). This screening led to the identification of 594 nascent ventures (i.e., firms that are not operating yet) and 514 young firms (i.e., firms that have started operating from 2004) that were willing to participate in the study. Comprehensive phone interviews were conducted with these 1108 ventures. In a likewise comprehensive follow-up 12 months later, 80% of the eligible cases completed the interview. The questionnaire contains specific sections designed to distinguish effectual and causal processes, innovation, gestation activities, business idea changes and ventures outcomes. The effectuation questions are based on the components of effectuation strategy as described by Sarasvathy (2001) namely: flexibility, affordable loss and pre-commitment from stakeholders. Results from two rounds of pre-testing informed the design of the instrument included in the main survey. The first two waves of data have will be used to test and compare the use of effectuation in the venture creation process. To increase the robustness of the results, temporal use of effectuation will be tested both directly and indirectly. 1. By comparing the use of effectuation in nascent and young firms from wave 1 to 2, we will be able to find out how effectuation is affected by time over a 12-month duration and if the stage of venture development has an impact on its use. 2. By comparing nascent ventures early in the creation process versus nascent ventures late in the creation process. Early versus late can be determined with the help of time-stamped gestation activity questions included in the survey. This will help us to determine the change on a small time scale during the creation phase of the venture. 3. By comparing nascent firms to young (already operational) firms. 4. By comparing young firms becoming operational in 2006 with those first becoming operational in 2004. Results and Implications : Wave 1 and 2 data have been completed and wave 2 is currently being checked and 'cleaned'. Analysis work will commence in September, 2009. This paper is expected to contribute to the body of knowledge on effectuation by measuring quantitatively its use and impact on nascent and young firms activities at different stages of their development. In addition, this study will also increase the understanding of the venture creation process by comparing over time nascent and young firms from a large sample of randomly selected ventures. We acknowledge the results from this study will be preliminary and will have to be interpreted with caution as the changes identified may be due to several factors and may not only be attributed to the use/not use of effectuation. Meanwhile, we believe that this study is important to the field of entrepreneurship as it provides some much needed insights on the processes used by nascent and young firms during their creation and early operating stages.

Role of low affinity beta1-adrenergic receptors in normal and diseased hearts

ROLE OF LOW AFFINITY β1-ADRENERGIC RECEPTOR IN NORMAL AND DISEASED HEARTS Background: The β1-adrenergic receptor (AR) has at least two binding sites, 1HAR and 1LAR (high and low affinity site of the 1AR respectively) which cause cardiostimulation. Some β-blockers, for example (-)-pindolol and (-)-CGP 12177 can activate β1LAR at higher concentrations than those required to block β1HAR. While β1HAR can be blocked by all clinically used β-blockers, β1LAR is relatively resistant to blockade. Thus, chronic β1LAR activation may occur in the setting of β-blocker therapy, thereby mediating persistent βAR signaling. Thus, it is important to determine the potential significance of β1LAR in vivo, particularly in disease settings. Method and result: C57Bl/6 male mice were used. Chronic (4 weeks) β1LAR activation was achieved by treatment with (-)-CGP12177 via osmotic minipump. Cardiac function was assessed by echocardiography and catheterization. (-)-CGP12177 treatment in healthy mice increased heart rate and left ventricular (LV) contractility without detectable LV remodelling or hypertrophy. In mice subjected to an 8-week period of aorta banding, (-)-CGP12177 treatment given during 4-8 weeks led to a positive inotropic effect. (-)-CGP12177 treatment exacerbated LV remodelling indicated by a worsening of LV hypertrophy by ??% (estimated by weight, wall thickness, cardiomyocyte size) and interstitial/perivascular fibrosis (by histology). Importantly, (-)-CGP12177 treatment to aorta banded mice exacerbated cardiac expression of hypertrophic, fibrogenic and inflammatory genes (all p<0.05 vs. non-treated control with aorta banding).. Conclusion: β1LAR activation provides functional support to the heart, in both normal and diseased (pressure overload) settings. Sustained β1LAR activation in the diseased heart exacerbates LV remodelling and therefore may promote disease progression from compensatory hypertrophy to heart failure. Word count: 270

Human preadipocyte proliferation and differentiation

Obesity represents a major health, social and economic burden to many developing and Westernized communities, with the prevalence increasing at a rate exceeding almost all other medical conditions. Despite major recent advances in our understanding of adipose tissue metabolism and dynamics, we still have limited insight into the regulation of adipose tissue mass in humans. Any significant increase in adipose tissue mass requires proliferation and differentiation of precursor cells (preadipocytes) present in the stromo-vascular compartment of adipose tissue. These processes are very complex and an increasing number of growth factors and hormones have been shown to modulate the expression of genes involved in preadipocyte proliferation and differentiation. A number of transcription factors, including the C/EBP family and PP ARy, have been identified as integral to adipose tissue development and preadipocyte differentiation. Together PP ARy and C/EBPa regulate important events in the activation and maintenance of the terminally differentiated phenotype. The ability of PP ARy to increase transcription through its DNA recognition site is dependent on the binding of ligands. This suggests that an endogenous PP ARy ligand may be an important regulator of adipogenesis. Adipose tissue functions as both the major site of energy storage in the body and as an endocrine organ synthesizing and secreting a number of important molecules involved in regulation of energy balance. For optimum functioning therefore, adipose tissue requires extensive vascularization and previous studies have shown that growth of adipose tissue is preceded by development of a microvascular network. This suggests that paracrine interactions between constituent cells in adipose tissue may be involved in both new capillary formation and fat cell growth. To address this hypothesis the work in this project was aimed at (a) further development of a method for inducing preadipocyte differentiation in subcultured human cells; (b) establishing a method for simultaneous isolation and separate culture of both preadipocytes and microvascular endothelial cells from the same adipose tissue biopsies; (c) to determine, using conditioned medium and co-culture techniques, if endothelial cell-derived factors influence the proliferation and/or differentiation of human preadipocytes; and (d) commence characterization of factors that may be responsible for any observed paracrine effects on aspects of human adipogenesis. Major findings of these studies were as follows: (A) Inclusion of either linoleic acid (a long-chain fatty acid reported to be a naturally occurring ligand for PP ARy) or Rosiglitazone (a member of the thiazolidinedione class of insulin-sensitizing drugs and a synthetic PPARy ligand) in differentiation medium had markedly different effects on preadipocyte differentiation. These studies showed that human preadipocytes have the potential to accumulate triacylglycerol irrespective of their stage of biochemical differentiation, and that thiazolidinediones and fatty acids may exert their adipogenic and lipogenic effects via different biochemical pathways. It was concluded that Rosiglitazone is a more potent inducer of human preadipocyte differentiation than linoleic acid. (B) A method for isolation and culture of both endothelial cells and preadipocytes from the same adipose tissue biopsy was developed. Adipose-derived microvascular endothelial cells were found to produce factor/s, which enhance both proliferation and differentiation of human preadipocytes. (C) The adipogenic effects of microvascular endothelial cells can be mimicked by exposure of preadipocytes to members of the Fibroblast Growth Factor family, specifically ~-ECGF and FGF-1. (D) Co-culture of human preadipocytes with endothelial cells or exposure of preadipocytes to either ~-ECGF or FGF-1 were found to 'prime' human preadipocytes, during their proliferative phase of growth, for thiazolidinedione-induced differentiation. (E) FGF -1 was not found to be acting as a ligand for PP ARy in this system. Findings from this project represent a significant step forward in our understanding of factors involved in growth of human adipose tissue and may lead to the development of therapeutic strategies aimed at modifying the process. Such strategies would have potential clinical utility in the treatment of obesity and obesity related disorders such as Type II Diabetes.

Evaluating the effect of a patient education brochure on patients’ expectations and satisfaction with emergency department service

Introduction: The purpose of this study was to assess the capacity of a written intervention, in this case a patient information brochure, to improve patient satisfaction during an Emergency Department (ED) visit. For the purpose of measuring the effect of the intervention the ED journey was conceptualised as a series of distinct areas of service comprising waiting time, service by the triage nurse, care from doctors and nurses and information giving Background of study: Research into patient satisfaction has become a widespread activity endorsed by both governments and hospital administrations. The literature on ED patient satisfaction has consistently indicated three primary areas of patient dissatisfaction: waiting time, nursing care and communication. Recent developments in the literature on patient satisfaction studies however have highlighted the relationship between patients. expectations of a service encounter and their consequent assessment of the experience as dissatisfying or satisfying. Disconfirmation theory posits that the degree to which expectations are confirmed will affect subsequent levels of satisfaction. The conceptual framework utilised in this study is Coye.s (2004) model of disconfirmation. Coye while reiterating satisfaction is a consequence of the degree expectations are either confirmed or disconfirmed also posits that expectations can be modified by interventions. Coye.s work conceptualises these interventions as intra encounter experiences (cues) which function to adjust expectations. Coye suggests some cues are unintended and may have a negative impact which also reinforces the value of planned cues intended to meet or exceed consumer expectations. Consequently the brochure can be characterized as a potentially positive cue, encouraging the patient to understand processes and to orient them in what can be a confronting environment. Only a limited number of studies have examined the effect of written interventions within an ED. No studies could be located which have tested the effect of ED interventions using a conceptual framework which relates the effect of the degree to which expectations are confirmed or disconfirmed in terms of satisfaction with services. Method: Two studies were conducted. Study One used qualitative methods to explore patients. expectations of the ED from the perspective of both patients and health care professionals. Study One was used in part to direct the development of the intervention (brochure) in Study Two. The brochure was an intervention designed to modify patients. expectations thus increasing their satisfaction with the provision of ED service. As there was no existing tools to measure ED patients. expectations and satisfaction a new tool was also developed based on the findings and the literature of Study One. Study Two used a non-randomised, quasi-experimental approach using a non-equivalent post-test only comparison group design used to investigate the effect of the patient education brochure (Stommel and Wills, 2004). The brochure was disseminated to one of two study groups (the intervention group). The effect of the brochure was assessed by comparing the data obtained from both the intervention and control group. These two groups consisted of 150 participants each. It was expected that any differences in the relevant domains selected for examination would indicate the effect of the brochure both on expectation and potentially satisfaction. Results: Study One revealed several areas of common ground between patients and nurses in terms of relevant content for the written intervention, including the need for information on the triage system and waiting times. Areas of difference were also found with patients emphasizing communication issues, whereas focus group members expressed concern that patients were often unable to assimilate verbal information. The findings suggested the potential utility of written material to reinforce verbal communication particularly in terms of the triage process and other ED protocols. This material was synthesized within the final version of the written intervention. Overall the results of Study Two indicated no significant differences between the two groups. The intervention group did indicate a significant number of participants who viewed the brochure of having changed their expectations. The effect of the brochure may have been obscured by a lack of parity between the two groups as the control group presented with statistically significantly higher levels of acuity and experienced significantly shorter waiting times. In terms of disconfirmation theory this would suggest expectations that had been met or exceeded. The results confirmed the correlation of expectations with satisfaction. Several domains also indicated age as a significant predictor with older patients tending to score higher satisfaction results. Other significant predictors of satisfaction established were waiting time and care from nurses, reinforcing the combination of efficient service and positive interpersonal experiences as being valued by patients. Conclusions: Information presented in written form appears to benefit a significant number of ED users in terms of orientation and explaining systems and procedures. The degree to which these effects may interact with other dimensions of satisfaction however is likely to be limited. Waiting time and interpersonal behaviours from staff also provide influential cues in determining satisfaction. Written material is likely to be one element in a series of coordinated strategies to improve patient satisfaction during periods of peak demand.