Control design for multicast-aware class-based networks

The expectations of citizens from the Information Technologies (ITs) are increasing as the ITs have become integral part of our society, serving all kinds of activities whether professional, leisure, safety-critical applications or business. Hence, the limitations of the traditional network designs to provide innovative and enhanced services and applications motivated a consensus to integrate all services over packet switching infrastructures, using the Internet Protocol, so as to leverage flexible control and economical benefits in the Next Generation Networks (NGNs). However, the Internet is not capable of treating services differently while each service has its own requirements (e.g., Quality of Service - QoS). Therefore, the need for more evolved forms of communications has driven to radical changes of architectural and layering designs which demand appropriate solutions for service admission and network resources control. This Thesis addresses QoS and network control issues, aiming to improve overall control performance in current and future networks which classify services into classes. The Thesis is divided into three parts. In the first part, we propose two resource over-reservation algorithms, a Class-based bandwidth Over-Reservation (COR) and an Enhanced COR (ECOR). The over-reservation means reserving more bandwidth than a Class of Service (CoS) needs, so the QoS reservation signalling rate is reduced. COR and ECOR allow for dynamically defining over-reservation parameters for CoSs based on network interfaces resource conditions; they aim to reduce QoS signalling and related overhead without incurring CoS starvation or waste of bandwidth. ECOR differs from COR by allowing for optimizing control overhead minimization. Further, we propose a centralized control mechanism called Advanced Centralization Architecture (ACA), that uses a single state-full Control Decision Point (CDP) which maintains a good view of its underlying network topology and the related links resource statistics on real-time basis to control the overall network. It is very important to mention that, in this Thesis, we use multicast trees as the basis for session transport, not only for group communication purposes, but mainly to pin packets of a session mapped to a tree to follow the desired tree. Our simulation results prove a drastic reduction of QoS control signalling and the related overhead without QoS violation or waste of resources. Besides, we provide a generic-purpose analytical model to assess the impact of various parameters (e.g., link capacity, session dynamics, etc.) that generally challenge resource overprovisioning control. In the second part of this Thesis, we propose a decentralization control mechanism called Advanced Class-based resource OverpRovisioning (ACOR), that aims to achieve better scalability than the ACA approach. ACOR enables multiple CDPs, distributed at network edge, to cooperate and exchange appropriate control data (e.g., trees and bandwidth usage information) such that each CDP is able to maintain a good knowledge of the network topology and the related links resource statistics on real-time basis. From scalability perspective, ACOR cooperation is selective, meaning that control information is exchanged dynamically among only the CDPs which are concerned (correlated). Moreover, the synchronization is carried out through our proposed concept of Virtual Over-Provisioned Resource (VOPR), which is a share of over-reservations of each interface to each tree that uses the interface. Thus, each CDP can process several session requests over a tree without requiring synchronization between the correlated CDPs as long as the VOPR of the tree is not exhausted. Analytical and simulation results demonstrate that aggregate over-reservation control in decentralized scenarios keep low signalling without QoS violations or waste of resources. We also introduced a control signalling protocol called ACOR Protocol (ACOR-P) to support the centralization and decentralization designs in this Thesis. Further, we propose an Extended ACOR (E-ACOR) which aggregates the VOPR of all trees that originate at the same CDP, and more session requests can be processed without synchronization when compared with ACOR. In addition, E-ACOR introduces a mechanism to efficiently track network congestion information to prevent unnecessary synchronization during congestion time when VOPRs would exhaust upon every session request. The performance evaluation through analytical and simulation results proves the superiority of E-ACOR in minimizing overall control signalling overhead while keeping all advantages of ACOR, that is, without incurring QoS violations or waste of resources. The last part of this Thesis includes the Survivable ACOR (SACOR) proposal to support stable operations of the QoS and network control mechanisms in case of failures and recoveries (e.g., of links and nodes). The performance results show flexible survivability characterized by fast convergence time and differentiation of traffic re-routing under efficient resource utilization i.e. without wasting bandwidth. In summary, the QoS and architectural control mechanisms proposed in this Thesis provide efficient and scalable support for network control key sub-systems (e.g., QoS and resource control, traffic engineering, multicasting, etc.), and thus allow for optimizing network overall control performance.

Calculus of variations on time scales and applications to economics

We consider some problems of the calculus of variations on time scales. On the beginning our attention is paid on two inverse extremal problems on arbitrary time scales. Firstly, using the Euler-Lagrange equation and the strengthened Legendre condition, we derive a general form for a variation functional that attains a local minimum at a given point of the vector space. Furthermore, we prove a necessary condition for a dynamic integro-differential equation to be an Euler-Lagrange equation. New and interesting results for the discrete and quantum calculus are obtained as particular cases. Afterwards, we prove Euler-Lagrange type equations and transversality conditions for generalized infinite horizon problems. Next we investigate the composition of a certain scalar function with delta and nabla integrals of a vector valued field. Euler-Lagrange equations in integral form, transversality conditions, and necessary optimality conditions for isoperimetric problems, on an arbitrary time scale, are proved. In the end, two main issues of application of time scales in economic, with interesting results, are presented. In the former case we consider a firm that wants to program its production and investment policies to reach a given production rate and to maximize its future market competitiveness. The model which describes firm activities is studied in two different ways: using classical discretizations; and applying discrete versions of our result on time scales. In the end we compare the cost functional values obtained from those two approaches. The latter problem is more complex and relates to rate of inflation, p, and rate of unemployment, u, which inflict a social loss. Using known relations between p, u, and the expected rate of inflation π, we rewrite the social loss function as a function of π. We present this model in the time scale framework and find an optimal path π that minimizes the total social loss over a given time interval.

Characterization of water-soluble organic matter from urban aerosols

Water-soluble organic matter (WSOM) from atmospheric particles comprises a complex array of molecular structures that play an important role on the physic-chemical properties of atmospheric particles and, therefore, are linked to several global-relevant atmospheric processes which impact the climate and public health. Due to the large variety of sources and formation processes, adequate knowledge on WSOM composition and its effects on the properties of atmospheric aerosol are still limited. Therefore, this thesis aims at providing new insights on the molecular composition of WSOM from fine atmospheric aerosols typical of an urban area (Aveiro, Portugal). In a first step, adsorption phenomena of semivolatile organic compounds on quartz fibre filters employed in the collection of atmospheric aerosols were assessed. Afterwards, atmospheric aerosol samples were collected during fifteen months, on a weekly basis. A mass balance of aerosol samples was performed in order to set the relative contribution of elemental carbon, WSOM and water-insoluble organic matter to the aerosol mass collected at the urban area of Aveiro, with a special focus on the assessment of the influence of different meteorological conditions. In order to assess the chemical complexity of the WSOM from urban aerosols, their structural characteristics were studied by means of Fourier transform infrared infrared - Attenuated Total Reflectance (FTIR-ATR) and solid-state cross polarization with magic angle spinning 13C nuclear magnetic resonance (CPMAS 13C NMR) spectroscopies, as well as their elemental composition. The structural characterization of aerosol WSOM samples collected in the urban area highlighted a highly complex mixture of functional groups. It was concluded that aliphatic and aromatic structures, hydroxyl groups and carboxyl groups are characteristic to all samples. The semi-quantitative assessment of the CPMAS 13C NMR data showed different distributions of the various functional groups between the aerosol samples collected at different seasons. Moreover, the presence of signals typical of lignin-derived structures in both CPMAS 13C NMR and FTIR-ATR spectra of the WSOM samples from the colder seasons, highlights the major contribution of biomass burning processes in domestic fireplaces, during low temperature conditions, into the bulk chemical properties of WSOM from urban aerosols. A comprehensive two-dimensional liquid chromatography (LC x LC) method, on-line coupled to a diode array, fluorescence, and evaporative light scattering detectors, was employed for resolving the chemical heterogeneity of the aerosol WSOM samples and, simultaneously, to map the hydrophobicity versus the molecular weight distribution of the samples. The LC x LC method employed a mixed-mode hydrophilic interaction column operating under aqueous reversed phase mode in the first dimension, and a size-exclusion column in the second dimension, which was found to be useful for separating the aerosol WSOM samples into various fractions with distinct molecular weight and hydrophobic features. The estimative of the average molecular weight (Mw) distribution of the urban aerosol WSOM samples ranged from 48 to 942 Da and from 45 to 1241 Da in terms of UV absorption and fluorescence detection, respectively. Findings suggest that smaller Mw group fractions seem to be related to a more hydrophobic nature.

Promoção da acessibilidade em televisão interativa (iTV) : proposta de um serviço adaptado a utilizadores com défice visual

As infraestruturas de televisão interativa atualmente existentes possibilitam a integração de uma grande variedade de recursos e serviços, possibilitando aos utilizadores novas experiências de interação e participação. Para a maioria dos telespetadores, o uso de serviços interativos não acarreta grandes dificuldades; no entanto, para públicos com necessidades especiais, por exemplo para pessoas com défice visual, essa tarefa torna-se complexa, dificultando, ou mesmo impedindo, que estes utilizadores possam beneficiar deste tipo de serviços. Portugal não é uma exceção neste contexto, existindo um número significativo de utilizadores com défice visual (UDV) que não beneficiam totalmente das potencialidades do paradigma televisivo atual. Neste âmbito, o projeto de investigação que suporta esta tese explora a problemática do Design Universal aplicado à Televisão Interativa (iTV) e tem como objetivos a conceptualização, prototipagem e validação de um serviço de iTV adaptado especificamente a UDV, visando promover a sua inclusão digital. Para cumprir estes objetivos, a investigação dividiu-se em três etapas distintas. Na primeira etapa, a partir da Teoria Fundamentada nos Dados, foram identificadas as dificuldades e necessidades dos UDV enquanto consumidores de conteúdos televisivos e serviços de audiodescrição; foi selecionada a plataforma tecnológica mais adequada para o suporte do serviço prototipado; e foi definido um conjunto de princípios orientadores de design (POD’s) de interfaces de televisão interativa específico para este público-alvo. Inicialmente foram efetuadas duas entrevistas a 20 participantes com défice visual, para determinar as suas dificuldades e necessidades enquanto consumidores de conteúdos televisivos e serviços de audiodescrição. De seguida, foi realizada uma entrevista a um perito responsável pelo processo de transição para a TDT em Portugal (inicialmente considerou-se que a TDT seria uma plataforma promissora e poderia suportar o protótipo) e efetuada a revisão da literatura sobre POD’s para o desenvolvimento de interfaces para serviços iTV dirigidos a pessoas com défice visual. A partir dos resultados obtidos nesta etapa foi possível definir os requisitos funcionais e técnicos do sistema, bem como os seus PODs, tanto ao nível da componente gráfica, como de interação. Na segunda etapa foi concetualizado e desenvolvido o protótipo iTV adaptado a UDV ‘meo ad+’, com recurso à plataforma tecnológica IPTV da Portugal Telecom, seguindo os requisitos e os princípios de design definidos. Relativamente à terceira etapa, esta contemplou a avaliação do serviço prototipado, por parte de um grupo de participantes com défice visual. Esta fase do trabalho foi conduzida através do método de Estudo Avaliativo, possibilitando, através de testes de usabilidade e acessibilidade, complementados com entrevistas, compreender se o serviço prototipado ia efetivamente ao encontro das necessidades deste tipo de utilizadores, tendo-se observado que os participantes que estiveram envolvidos nos testes ao protótipo mostraram-se satisfeitos com as funcionalidades oferecidas pelo sistema, bem como com o design da sua interface.

Identificação de utilizadores seniores em televisão interativa (iTV) : uma matriz de decisão tecnológica

Desde que surgiu há mais de 50 anos, a televisão sofreu muitas transformações, tanto ao nível tecnológico (por exemplo com a passagem da emissão a preto/branco para cor, o som analógico para digital, a difusão digital) como a nível da sua influência nas sociedades. Entre outros fatores de ordem tecnológica, a consolidação da Internet com o seu elevado nível de personalização, da experiência de utilização, e a sua enorme quantidade de conteúdos disponíveis, catapultou a televisão no sentido de esta se tornar mais interativa. Assim, o telespectador passou a poder usufruir de uma experiência televisiva que pode, por um lado, ser mais participativa, sendo-lhe possível, por exemplo, alvitrar sobre a qualidade de um programa enquanto assiste à sua exibição, e, por outro, ser mais personalizada, possibilitando-lhe, por exemplo, receber conteúdos automaticamente adequados ao seu perfil e contexto. No entanto, esta experiência mais participativa e personalizável carece de uma identificação, idealmente automática e não intrusiva, de quem pode beneficiar da mesma – o telespectador. Contudo, e apesar de significativos avanços na área da televisão interativa, tanto ao nível da infraestrutura de suporte como ao nível dos serviços disponibilizados, a identificação dos utilizadores é, ainda, uma área de estudo com muitos aspetos por compreender. Os seniores, em particular, são grandes consumidores de televisão e representam uma fatia muito considerável das pessoas que podem beneficiar das potencialidades disponibilizadas pela interatividade presente em muitos serviços atuais. Um número crescente destes serviços são desenhados com o objetivo de promoverem um envelhecimento ativo e um concreto apoio à vida, pelo que os seniores podem beneficiar, em vários aspetos do seu quotidiano, se os utilizarem. Nesta faixa etária, a identificação de utilizadores tem, como elemento potenciador da experiência de utilização, um papel especialmente importante ao nível de um aproveitamento personalizado e dirigido destes serviços. No entanto, atendendo às diferentes combinações de características físicas, sensoriais, cognitivas e, mesmo, de literacia digital que tipificam os seniores, perspetivou-se existir uma dependência do perfil do utilizador na seleção do método de identificação mais adequado, os quais podem ser baseados, por exemplo, num leitor de impressões digitais, instalado no telecomando; na leitura de uma wearable tag ou de um cartão RFiD; no reconhecimento da face e, eventualmente, na voz do utilizador. Assim, a inerente investigação desenrolou-se em várias fases, no sentido de permitir alicerçar a construção de uma matriz de decisão tecnológica que, em função do perfil de utilizador, selecione o sistema de identificação mais adequado. O procedimento metodológico inerente à construção desta matriz de decisão, passou por um longo processo envolvendo utilizadores reais, que se iniciou com a realização de entrevistas exploratórias com o objetivo de permitir conhecer melhor os seniores e a forma como estes encaram a tecnologia e, mais concretamente, a televisão interativa. Foi depois implementado um protótipo de alta-fidelidade, completamente funcional, para a realização de testes com o objetivo de perceber qual a preferência relativamente a um subconjunto de tecnologias de identificação. Estes testes, uma vez que não permitiram testar todas as tecnologias em estudo, revelaram-se inconclusivos, porém permitiram reforçar a necessidade de identificar e caracterizar os referidos aspetos do perfil do utilizador que podem interferir na sua preferência relativamente ao sistema de identificação. As características identificadas constituíram-se como os parâmetros de entrada da matriz, sendo que para preencher as respetivas células realizaramse testes de aceitação, com um conjunto de seniores, tendo por base um protótipo, wizard of oz, especificamente implementado para permitir experienciar todas as tecnologias em estudo. Estes testes foram precedidos pela avaliação das capacidades funcionais dos participantes, nos diversos parâmetros definidos. Este texto relata, assim, todo o processo de investigação que foi conduzido, terminando com uma descrição de exemplos de utilização da matriz de decisão implementada e com a identificação de potenciais caminhos de desenvolvimento deste trabalho.

O desenho da comunicação como conhecimento

As últimas décadas do séc. XX assistiram a um crescente protagonismo do Design de Informação que, desde então, tem sofrido inúmeras formas e designações, num processo de afirmação e auto descoberta. A proliferação de dados disponíveis deu ao design e em particular a este ramo do desenho para a compreensão, uma visibilidade crescente e a responsabilidade de encontrar, a partir da informação, novos meios para a construção de sentido. Do design à engenharia informática, são várias as disciplinas que convergem hoje nesse desígnio ainda que sob diferentes modelos e ferramentas. Esta convergência promove uma comparação entre modelos, que tendem a ser tanto mais valorizados quanto mais objectivas as representações. De Playfair a Bertin, as representações gráficas dos últimos duzentos anos têm-se situado no âmbito de disciplinas como a Economia, Sociologia ou a Gestão, explorando metáforas funcionais com vista à evidência da tradução numérica. O Design, enquanto mediador cultural e através do Desenho, tende a acrescentar ao mesmo exercício uma dimensão narrativa ou ilustrativa, convocando a própria existência do autor na interpretação dos mesmos dados numéricos. Com esta investigação, novos processos de semiose se oferecem, associando à objectividade dos dados quantitativos, a subjectividade da cultura formulada a partir do indivíduo enquanto intérprete. Na procura do conhecimento, reconhece-se assim que o desenho da informação ganha competências pela mediação da experiência, religando ética, técnica e estética.

Interactions of cetaceans with Spanish and Portuguese fisheries in Atlantic waters : costs, benefits and implications for management

With the aim to provide new insights into operational cetacean-fishery interactions in Atlantic waters, this thesis assesses interactions of cetaceans with Spanish and Portuguese fishing vessels operating in Iberian and South West Atlantic waters. Different opportunistic research methodologies were applied, including an interview survey with fishers (mainly skippers) and onboard observations by fisheries observers and skippers, to describe different types of interactions and to identify potential hotspots for cetacean-fishery interactions and the cetacean species most involved, and to quantify the extent and the consequences of these interactions in terms of benefits and costs for cetaceans and fisheries. In addition, the suitability of different mitigation strategies was evaluated and discussed. The results of this work indicate that cetaceans interact frequently with Spanish and Portuguese fishing vessels, sometimes in a beneficial way (e.g. cetaceans indicate fish schools in purse seine fisheries), but mostly with negative consequences (depredation on catch, gear damage and cetacean bycatch). Significant economic loss and high bycatch rates are, however, only reported for certain fisheries and associated with particular cetacean species. In Galician fisheries, substantial economic loss was reported as a result of bottlenose dolphins damaging artisanal coastal gillnets, while high catch loss may arise from common dolphins scattering fish in purse seine fisheries. High cetacean bycatch mortality arises in trawl fisheries, mainly of common dolphin and particularly during trawling in water depths below 350 m, and in coastal set gillnet fisheries (mainly common and bottlenose dolphins). In large-scale bottom-set longline fisheries in South West Atlantic waters, sperm whales may significantly reduce catch rates through depredation on catch. The high diversity of cetacean-fishery interactions observed in the study area indicates that case-specific management strategies are needed to reduce negative impacts on fisheries and cetaceans. Acoustic deterrent devices (pingers) may be used to prevent small cetaceans from approaching and getting entangled in purse seines and set gillnets, although possible problems include cetacean habituation to the pinger sounds, as well as negative side effects on non-target cetaceans (habitat exclusion) and fisheries target species (reduced catch rates). For sardine and horse mackerel, target species of Iberian Atlantic fisheries, no aversive reaction to pinger sounds was detected during tank experiments conducted in the scope of this thesis. Bycatch in trawls may be reduced by the implementation of time/area restrictions of fishing activity. In addition, the avoidance of fishing areas with high cetacean abundance combined with the minimization of fishery-specific sound cues that possibly attract cetaceans, may also help to decrease interactions. In large-scale bottom-set longline fisheries, cetacean depredation on catch may be reduced by covering hooked fish with net sleeves ("umbrellas") provided that catch rates are not negatively affected by this gear modification. Trap fishing, as an alternative fishing method to bottom-set gillnetting and longlining, also has the potential to reduce cetacean bycatch and depredation, given that fish catch rates are similar to the rates obtained by bottom-set gillnets and longlines, whereas cetacean by-catch is unlikely. Economic incentives, such as the eco-certification of dolphin-safe fishing methods, should be promoted in order to create an additional source of income for fishers negatively affected by interactions with cetaceans, which, in turn, may also increase fishers’ willingness to accept and adopt mitigation measures. Although the opportunistic sampling methods applied in this work have certain restrictions concerning their reliability and precision, the results are consistent with previous studies in the same area. Moreover, they allow for the active participation of fishers that can provide important complementary ecological and technical knowledge required for cetacean management and conservation.

Alkali-free bioactive glasses for bone regeneration

Bioactive glasses and glass-ceramics are a class of third generation biomaterials which elicit a special response on their surface when in contact with biological fluids, leading to strong bonding to living tissues. The purpose of the present study was to develop diopside based alkali-free bioactive glasses in order to achieve good sintering behaviour, high bioactivity, and a dissolution/ degradation rates compatible with the target applications in bone regeneration and tissue engineering. Another aim was to understand the structure-property relationships in the investigated bioactive glasses. In this quest, various glass compositions within the Diopside (CaMgSi2O6) – Fluorapatite (Ca5(PO4)3F) – Tricalcium phosphate (3CaO•P2O5) system have been investigated. All the glasses were prepared by melt-quenching technique and characterized by a wide array of complementary characterization techniques. The glass-ceramics were produced by sintering of glass powders compacts followed by a suitable heat treatment to promote the nucleation and crystallization phenomena. Furthermore, selected parent glass compositions were doped with several functional ions and an attempt to understand their effects on the glass structure, sintering ability and on the in vitro bio-degradation and biomineralization behaviours of the glasses was made. The effects of the same variables on the devitrification (nucleation and crystallization) behaviour of glasses to form bioactive glass-ceramics were also investigated. Some of the glasses exhibited high bio-mineralization rates, expressed by the formation of a surface hydroxyapatite layer within 1–12 h of immersion in a simulated body fluid (SBF) solution. All the glasses showed relatively lower degradation rates in comparison to that of 45S5 Bioglass®. Some of the glasses showed very good in vitro behaviour and the glasses co-doped with zinc and strontium showed an in vitro dose dependent behaviour. The as-designed bioactive glasses and glass–ceramic materials are excellent candidates for applications in bone regeneration and for the fabrication of scaffolds for tissue engineering.

Materiais à base de óxidos com estrutura do tipo perovskite e compósitos como ânodos de PCES

This work was focused on the analysis of transport, thermomechanical and electrochemical properties of a series of perovskite-like oxide materials and composites for potential applications as anodes of intermediate-temperature solid oxide fuel cells (SOFCs) with lanthanum gallate and silicate solid electrolytes. The primary attention was centered on A(Mn,Nb)O3-δ (A = Sr, Ca) and (La,Sr)(Mn,Ti)O3-based systems, lanthanum chromite substituted with acceptor-type and variable-valence cations, and various Ni-containing cermets. Emphasis was given to phase stability of the materials, their crystal structure, microstructure of porous electrode layers and dense ceramics, electronic conductivity, Seebeck coefficient, oxygen permeability, thermal and chemical induced expansion, and anodic overpotentials of the electrodes deposited onto (La,Sr)(Ga,Mg)O3- and La10(Si,Al)6O27- based electrolyte membranes. In selected cases, roles of oxygen diffusivity, states of the transition metal cations relevant for the electronic transport, catalytically active additives and doped ceria protective interlayers introduced in the model electrochemical cells were assessed. The correlations between transport properties of the electrode materials and electrochemical behavior of porous electrodes showed that the principal factors governing anode performance include, in particular, electronic conduction of the anode compositions and cation interdiffusion between the electrodes and solid electrolytes. The latter is critically important for the silicatebased electrolyte membranes, leading to substantially worse anode properties compared to the electrochemical cells with lanthanum gallate solid electrolyte. The results made it possible to select several anode compositions exhibiting lower area-specific electrode resistivity compared to known analogues, such as (La,Sr)(Cr,Mn)O3-δ.

Microbe-mediated recovery of salt marshes contaminated with oil hydrocarbons

Salt marshes are highly productive intertidal habitats that serve as nursery grounds for many commercially and economically important species. Because of their location and physical and biological characteristics, salt marshes are considered to be particularly vulnerable to anthropogenic inputs of oil hydrocarbons. Sediment contamination with oil is especially dangerous for salt marsh vegetation, since low molecular weight aromatic hydrocarbons can affect plants at all stages of development. However, the use of vegetation for bioremediation (phytoremediation), by removal or sequestration of contaminants, has been intensively studied. Phytoremediation is an efficient, inexpensive and environmental friendly approach for the removal of aromatic hydrocarbons, through direct incorporation by the plant and by the intervention of degrading microbial populations in the rhizosphere (microbe-assisted phytoremediation). Rhizosphere microbial communities are enriched in important catabolic genotypes for degradation of oil hydrocarbons (OH) which may have a potential for detoxification of the sediment surrounding the roots. In addition, since rhizosphere bacterial populations may also internalize into plant tissues (endophytes), rhizocompetent AH degrading populations may be important for in planta AH degradation and detoxification. The present study involved field work and microcosms experiments aiming the characterization of relevant plant-microbe interactions in oilimpacted salt marshes and the understanding of the effect of rhizosphere and endosphere bacteria in the role of salt marsh plants as potential phytoremediation agents. In the field approach, molecular tools were used to assess how plant species- and OH pollution affect sediment bacterial composition [bulk sediment and sediment surrounding the roots (rhizosphere) of Halimione portulacoides and Sarcocornia perennis subsp. perennis] in a temperate estuary (Ria de Aveiro, Portugal) chronically exposed to OH pollution. In addition, the 16S rRNA gene sequences retrieved in this study were used to generate in silico metagenomes and to evaluate the distribution of potential bacterial traits in different microhabitats. Moreover, a combination of culture-dependent and -independent approaches was used to investigate the effect of oil hydrocarbons contamination on the structure and function of endophytic bacterial communities of salt marsh plants.Root systems of H. portulacoides and S. perennis subsp. perennis appear to be able to exert a strong influence on bacterial composition and in silico metagenome analysis showed enrichment of genes involved in the process of polycyclic aromatic hydrocarbon (PAH) degradation in the rhizosphere of halophyte plants. The culturable fraction of endophytic degraders was essentially closely related to known OH-degrading Pseudomonas species and endophytic communities revealed sitespecific effects related to the level of OH contamination in the sediment. In order to determine the effects of oil contamination on plant condition and on the responses in terms of structure and function of the bacterial community associated with plant roots (rhizosphere, endosphere), a microcosms approach was set up. The salt marsh plant Halimione portulacoides was inoculated with a previous isolated Pseudomonas sp. endophytic degrader and the 2-methylnaphthalene was used as model PAH contaminant. The results showed that H. portulacoides health and growth were not affected by the contamination with the tested concentration. Moreover, the decrease of 2-methylnaphthalene at the end of experiment, can suggest that H. portulacoides can be considered as a potential plant for future uses in phytoremedition approaches of contaminated salt marsh. The acceleration of hydrocarbon degradation by inoculation of the plants with the hydrocarbon-degrading Pseudomonas sp. could not, however, be demonstrated, although the effects of inoculation on the structure of the endophytic community observed at the end of the experiment indicate that the strain may be an efficient colonizer of H. portulacoides roots. The results obtained in this work suggest that H. portulacoides tolerates moderate concentrations of 2-methylnaphthalene and can be regarded as a promising agent for phytoremedition approaches in salt marshes contaminated with oil hydrocarbons. Plant/microbe interactions may have an important role in the degradation process, as plants support a diverse endophytic bacterial community, enriched in genetic factors (genes and plasmids) for hydrocarbon degradation.

Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Surface reactivity enhancement of silica-based glass-ceramic scaffolds

A paradigm shift is taking place from using transplanting tissue and synthetic implants to a tissue engineering approach that aims to regenerate damaged tissues by combining cells from the body with highly porous scaffold biomaterials, which act as templates, guiding the growth of new tissue. The central focus of this thesis was to produce porous glass and glass-ceramic scaffolds that exhibits a bioactive and biocompatible behaviour with specific surface reactivity in synthetic physiological fluids and cell-scaffold interactions, enhanced by composition and thermal treatments applied. Understanding the sintering behaviour and the interaction between the densification and crystallization processes of glass powders was essential for assessing the ideal sintering conditions for obtaining a glass scaffolds for tissue engineering applications. Our main goal was to carry out a comprehensive study of the bioactive glass sintering, identifying the powder size and sintering variables effect, for future design of sintered glass scaffolds with competent microstructures. The developed scaffolds prepared by the salt sintering method using a 3CaO.P2O5 - SiO2 - MgO glass system, with additions of Na2O with a salt, NaCl, exhibit high porosity, interconnectivity, pore size distribution and mechanical strength suitable for bone repair applications. The replacement of 6 % MgO by Na2O in the glass network allowed to tailor the dissolution rate and bioactivity of the glass scaffolds. Regarding the biological assessment, the incorporation of sodium to the composition resulted in an inibition cell response for small periods. Nevertheless it was demonstrated that for 21 days the cells response recovered and are similar for both glass compositions. The in vitro behaviour of the glass scaffolds was tested by introducing scaffolds to simulated body fluid for 21 days. Energy-dispersive Xray spectroscopy and SEM analyses proved the existence of CaP crystals for both compositions. Crystallization forming whitlockite was observed to affect the dissolution behaviour in simulated body fluid. By performing different heat treatments, it was possible to control the bioactivity and biocompatability of the glass scaffolds by means of a controlled crystallization. To recover and tune the bioactivity of the glass-ceramic with 82 % crystalline phase, different methods have been applied including functionalization using 3- aminopropyl-triethoxysilane (APTES). The glass ceramic modified surface exhibited an accelerated crystalline hydroxyapatite layer formation upon immersion in SBF after 21 days while the as prepared glass-ceramic had no detected formation of calcium phosphate up to 5 months. A sufficient mechanical support for bone tissue regeneration that biodegrade later at a tailorable rate was achievable with the glass–ceramic scaffold. Considering the biological assessment, scaffolds demonstrated an inductive effect on the proliferation of cells. The cells showed a normal morphology and high growth rate when compared to standard culture plates. This study opens up new possibilities for using 3CaO.P2O5–SiO2–MgO glass to manufacture various structures, while tailoring their bioactivity by controlling the content of the crystalline phase. Additionally, the in vitro behaviour of these structures suggests the high potential of these materials to be used in the field of tissue regeneration.

Decentralizing IP mobility management in future networks

The massive adoption of sophisticated mobile devices and applications led to the increase of mobile data in the last decade, which it is expected to continue. This increase of mobile data negatively impacts the network planning and dimension, since core networks are heavy centralized. Mobile operators are investigating atten network architectures that distribute the responsibility of providing connectivity and mobility, in order to improve the network scalability and performance. Moreover, service providers are moving the content servers closer to the user, in order to ensure high availability and performance of content delivery. Besides the e orts to overcome the explosion of mobile data, current mobility management models are heavy centralized to ensure reachability and session continuity to the users connected to the network. Nowadays, deployed architectures have a small number of centralized mobility anchors managing the mobile data and the mobility context of millions of users, which introduces issues related to performance and scalability that require costly network mechanisms. The mobility management needs to be rethought out-of-the box to cope with atten network architectures and distributed content servers closer to the user, which is the purpose of the work developed in this Thesis. The Thesis starts with a characterization of mobility management into well-de ned functional blocks, their interaction and potential grouping. The decentralized mobility management is studied through analytical models and simulations, in which di erent mobility approaches distinctly distribute the mobility management functionalities through the network. The outcome of this study showed that decentralized mobility management brings advantages. Hence, it was proposed a novel distributed and dynamic mobility management approach, which is exhaustively evaluated through analytical models, simulations and testbed experiments. The proposed approach is also integrated with seamless horizontal handover mechanisms, as well as evaluated in vehicular environments. The mobility mechanisms are also speci ed for multihomed scenarios, in order to provide data o oading with IP mobility from cellular to other access networks. In the pursuing of the optimized mobile routing path, a novel network-based strategy for localized mobility is addressed, in which a replication binding system is deployed in the mobility anchors distributed through the access routers and gateways. Finally, we go further in the mobility anchoring subject, presenting a context-aware adaptive IP mobility anchoring model that dynamically assigns the mobility anchors that provide the optimized routing path to a session, based on the user and network context. The integration of dynamic and distributed concepts in the mobility management, such as context-aware adaptive mobility anchoring and dynamic mobility support, allow the optimization of network resources and the improvement of user experience. The overall outcome demonstrates that decentralized mobility management is a promising direction, hence, its ideas should be taken into account by mobile operators in the deployment of future networks.

Ecological quality assessment in transitional systems

Estuaries are poles of attraction for human settlement which is a source of pressures to surface water bodies. The implementation of the European Water Framework Directive (WDF, 2000/60/EC) has increased the investigation in order to develop methodologies to assess the Ecological Quality Status (EQS) of aquatic ecosystems. Transitional systems are naturally stressed and characterized by highly dynamic physical, chemical and hydro-morphologic conditions and by species with a higher level of tolerance to change, being more difficult to develop suitable quality indicators for these systems. The general purpose of this study is to test the ability of synthesis descriptors, including primary (S, taxa richness) and derived biological variable (H’, Shannon-Wiener diversity), biotic indices (AMBI and M-AMBI), body size properties (abundance distribution by body size classes, length, weight and length-weight relationships) and non-taxonomic indices (ISS), as well as functional indicators related to the decomposition rates of various experimental substrates, a macrophyte (Phragmites australis) and an alga (Fucus vesiculosus), to evaluate the environmental quality in transitional systems. This study was carried out in one of the most pristine channels of the Ria the Aveiro, Mira Channel, along a full salinity gradient and in a metals and metalloid sediment contamination area, the Estarreja Channel, and two reference channels (Canelas and Salreu). In this study were used different sampling techniques, the leaf-bag technique and a hand-held corer. In Mira Channel, the alga and the macrophyte presented an opposite trend in the decomposition rate along the salinity gradient, with the decomposition rates of the alga always higher than those of the macrophyte. The decomposition rates of the macrophyte and the alga were higher in the mid estuary and in higher salinity areas, respectively, corresponding to the preferencial distribution areas of each species. The macrobenthic fauna associated with the decaying and an artificial substrate (control) showed equally well the benthic succession from the marine to the freshwater areas and, despite the strong differences in the decay rates, no significant differences were found between the benthic communities associated with the alga and the macrophyte. The body size properties of the macrobenthic fauna associated with the P. australis leaf-bag (1mm and 5mm) and corer samples were studied along the full salinity gradient. The dominant species of the sub-set of measured specimens were not the same of the original macrobenthic fauna sampled but, despite that, the sub-set of measured specimens was also able to show the benthic succession from the marine to the freshwater areas. The body size abundance distribution of the benthic macroinvertebrates according to the ISS size classes did not show a particular trend in any sampler along the salinity gradient. Significant differences were found in the length, weight and length-weight relationships of Annelids, , Molluscs and even some species along the salinity gradient. No significant differences were found in the AMBI, M-AMBI and ISS values along the salinity gradient for all the samplers. The EQS of the corer samples obtained using the M-AMBI was lower than that of the leaf-bags. The EQS obtained with the ISS was higher than that obtained with the M-AMBI in the leaf-bags but not in the corer samples. The ecological effects of contaminated sediments associated with the industrial chemical effluents discharged in the Estarreja Channel were studied a decade after ceasing the emissions, using the Sediment Quality Triad approach and two reference channels. The results showed that despite the emissions ceased in 2004, the sediment remains polluted with high levels of metals and metalloid, available to bioaccumulation and with severe consequences at the community level. The sediment contamination problem was also studied using the leaf-bag technique with a macrophyte, an alga and a control substrate. The results showed that the decay rates, the associated macrofauna and the application of the AMBI, M-AMBI and ISS indices to the mesh-bag samples were not able to identify the sediment contamination. Contrarily to the AMBI, the M-AMBI and the ISS showed significant differences between the contaminated and the reference channels for the corer samples. Although such statistical significance, the interest of using these complex biotic indices could be questioned, when much simple ones, like the S and H’ allow to reach the same conclusions.

Micro/nanoreservoirs for controlled release of active species in smart functional coatings

This work reports one possible way to develop new functional coatings used to increase the life time of metallic structures. The functionalities selected and attributed to model coatings in the frame of this work were corrosion protection, self-sensing and prevention of fouling (antifouling). The way used to confer those functionalities to coatings was based on the encapsulation of active compounds (corrosion inhibitors, pH indicators and biocides) in micro and nanocontainers followed by their incorporation into the coating matrices. To confer active corrosion protection, one corrosion inhibitor (2-mercaptobenzothiazole, MBT) was encapsulated in two different containers, firstly in silica nanocapsules (SiNC) and in polyurea microcapsules (PU-MC). The incorporation of both containers in different models coatings shows a significant improvement in the corrosion protection of aluminum alloy 2024 (AA2024). Following the same approach, SiNC and PU-MC were also used for the encapsulation of phenolphthalein (one well known pH indicator) to introduce sensing properties in polymeric coatings. SiNC and PU-MC containing phenolphthalein acted as corrosion sensor, showing a pink coloration due to the beginning of cathodic reaction, resulting in a pH increase identified by those capsules. Their sensing performance was proved in suspension and when integrated in coatings for aluminium alloy 2024 and magnesium alloy AZ31. In a similar way, the biocide activity (antifouling) was assigned to two polymeric matrices using SiNC for encapsulation of one biocide (Dichloro-2-octyl-2H-isothiazol-3-one, DCOIT) and also SiNC-MBT was tested as biocide. The antifouling activity of those two encapsulated compounds was assessed through inhibition and consequent decrease in the bioluminescence of modified E. coli. That effect was verified in suspension and when incorporated in coatings for AISI 1008 carbon steel. The developed micro and nanocontainers presented the desired performance, allowing the introduction of new functionalities to model coatings, showing potential to be used as functional additives in the next generation of multifunctional coatings.