Long-term response of corn to limited irrigation and crop rotations

Dwindling water supplies for irrigation are prompting alternative management choices by irrigators. Limited irrigation, where less water is applied than full crop demand, may be a viable approach. Application of limited irrigation to corn was examined in this research. Corn was grown in crop rotations with dryland, limited irrigation, or full irrigation management from 1985 to 1999. Crop rotations included corn following corn (continuous corn), corn following wheat, followed by soybean (wheat-corn-soybean), and corn following soybean (corn-soybean). Full irrigation was managed to meet crop evapotranspiration requirements (ETc). Limited irrigation was managed with a seasonal target of no more than 150 mm applied. Precipitation patterns influenced the outcomes of measured parameters. Dryland yields had the most variation, while fully irrigated yields varied the least. Limited irrigation yields were 80% to 90%> of fully irrigated yields, but the limited irrigation plots received about half the applied water. Grain yields were significantly different among irrigation treatments. Yields were not significantly different among rotation treatments for all years and water treatments. For soil water parameters, more statistical differences were detected among the water management treatments than among the crop rotation treatments. Economic projections of these management practices showed that full irrigation produced the most income if water was available. Limited irrigation increased income significantly from dryland management.

Long-term assessment of efficacy of permeable pond covers for odour reduction

Three anaerobic ponds used to store and treat piggery wastes were fully covered with permeable materials manufactured from polypropylene geofabric, polyethylene shade cloth and supported straw. The covers were assessed in terms of efficacy in reducing odour emission rates over a 40-month period. Odour samples were collected from the surface of the covers, the surface of the exposed liquor and from the surface of an uncovered (control) pond at one of the piggeries. Relative to the emission rate of the exposed liquor at each pond, the polypropylene, shade cloth and straw covers reduced average emission rates by 76%, 69% and 66%, respectively. At the piggery with an uncovered control pond, the polypropylene covers reduced average odour emission rates by 50% and 41%, respectively. A plausible hypothesis, consistent with likely mechanisms for the odour reduction and the olfactometric method used to quantifying the efficacy of the covers, is offered.

Destination image: identifying baseline perceptions of Brazil, Argentina and Chile in the nascent Australian long haul travel market

While the popularity of destination image research has increased exponentially in the literature, there has been relatively little published about perceptions held by international consumers of destinations in South America. The purpose of this paper is to report the findings of a research project that aimed to identify the baseline market perceptions of Brazil, Argentina and Chile amongst Australian residents, at the time of the emergence of this long haul market. Of interest was the extent to which Australians differentiate the three distinct countries versus perceiving the continent as a gestalt. These baseline perceptions enable the effectiveness of future marketing communications in Australia by the three national tourism offices to be monitored over time. Importance-Performance Analysis (IPA) is used as a practical analytical tool to guide decision makers. In terms of operationalising destination image, a key research finding was the very high ratio or participants using the ‘Don’t know’ (DK) option for each destination performance scale item. This finding has practical implications for the destination marketers, as well as for researchers engaged in destination image research in long haul and/or emerging markets.

Kaveriporukasta liiketoiminnaksi : Tuotannon häiriöt ja organisaation oppiminen nopeasti muuttuvassa yrityksessä

In the 1990 s the companies utilizing and producing new information technology, especially so-called new media, were also expected to be forerunners in new forms of work and organization. Researchers anticipated that new, more creative forms of work and the changing content of working life were about to replace old industrial and standardized ways of working. However, research on actual companies in the IT sector revealed a situation where only minor changes to existing organizational forms were seen .Many of the independent companies faced great difficulties trying to survive the rapid changes in the products and production forms in the emerging field. Most of the research on the new media field has been conducted as surveys, and an understanding of the actual everyday work process has remained thin. My research is a longitudinal study of the early phases of one new media company in Finland. The study is an analysis of the challenges the company faced in a rapidly changing business field and the attempts to overcome these challenges. The two main analyses in the study focus on the developmental phases of the company and the disturbances in the production process. Based on these analyses, I study changes and learning at work using the methodological framework of developmental work research. Developmental work research is a Finnish variant of the cultural-historical activity theory applied to the study of learning and transformations at work. The data was gathered over a three-year period of ethnographic fieldwork. I documented the production processes and everyday life in the company as a participant observer. I interviewed key persons, video and audio-taped meetings, followed e-mail correspondence and collected various documents, such as agreements and memos. I developed a systematic method for analyzing the disturbances in the production process by combining the various data sources. The systematic analysis of the disturbances depicted a very complex and only partly managed production process. The production process had a long duration, and no single actor had an understanding of it as a whole. Most of the disturbances had to do with the customer relationships. The nature of the disturbances was latent; they were recognized but not addressed. In the particular production processes that I analyzed, the ending life span of a particular product, a CD-ROM, became obvious. This finding can be interpreted in relation to the developmental phase of the production and the transformation of the field as a whole. Based on the analysis of the developmental phases and the disturbances, I formulate a hypothesis of the contradictions and developmental potentials of the activity studied. The conclusions of the study challenge the existing understanding of how to conceptualize and study organizational learning in production work. Most theories of organizational learning do not address qualitative changes in production nor historical challenges of organizational learning itself. My study opens up a new horizon in understanding organizational learning in a rapidly changing field where a learning culture based on craft or mass production work is insufficient. There is a need for anticipatory and proactive organizational learning. Proactive learning is needed to anticipate the changes in production type, and the life cycles of products.

Long-term trends in fertility of soils under continuous cultivation and cereal cropping in southern Queensland. IX. Simulation of soil carbon and nitrogen pools using CENTURY model

Cultivation and cropping of soils results in a decline in soil organic carbon and soil nitrogen, and can lead to reduced crop yields. The CENTURY model was used to simulate the effects of continuous cultivation and cereal cropping on total soil organic matter (C and N), carbon pools, nitrogen mineralisation, and crop yield from 6 locations in southern Queensland. The model was calibrated for each replicate from the original datasets, allowing comparisons for each replicate rather than site averages. The CENTURY model was able to satisfactorily predict the impact of long-term cultivation and cereal cropping on total organic carbon, but was less successful in simulating the different fractions and nitrogen mineralisation. The model firstly over-predicted the initial (pre-cropping) soil carbon and nitrogen concentration of the sites. To account for the unique shrinking and swelling characteristics of the Vertosol soils, the default annual decomposition rates of the slow and passive carbon pools were doubled, and then the model accurately predicted initial conditions. The ability of the model to predict carbon pool fractions varied, demonstrating the difficulty inherent in predicting the size of these conceptual pools. The strength of the model lies in the ability to closely predict the starting soil organic matter conditions, and the ability to predict the impact of clearing, cultivation, fertiliser application, and continuous cropping on total soil carbon and nitrogen.

Studies on friction and formation of transfer layer when Al-4Mg alloy pins slid at various numbers of cycles on steel plates of different surface texture

In the present investigation, various kinds of textures, namely, unidirectional, 8-ground, and random were attained on the die surfaces. Roughness of the textures was varied using different grits of emery papers or polishing powders. Then pins made of Al-4Mg alloys were slid against steel plates at various numbers of cycles, namely 1, 2, 6, 10 and 20 under both dry and lubricated conditions using an inclined pin-on-plate sliding tester. The morphologies of the worn surfaces of the pins and the formation of transfer layer on the counter surfaces were observed using a scanning electron microscope. Surface roughness parameters of the plate were measured using an optical profilometer. It was observed that the coefficient of friction and formation of transfer layer during the first few cycles depend on the die surface textures under both dry and lubricated conditions. It was also observed that under lubricated condition, the coefficient of friction decreases with number of cycles for all kinds of textures. However, under dry condition, it ecreases for unidirectional and 8-ground surfaces while for random surfaces it increases with number of cycles

Elasticity solution for a long circular sandwich cylindrical shell subjected to axisymmetric load

An elasticity solution has been obtained for a long circular sandwich cylindrical shell subjected to axisymmetric radial ring load using Love's stress function approach. Numerical results are presented for different ratios of modulus of elasticity of the layers. The results obtained from this analysis have been compared with those obtained from sandwich shell theory due to Fulton.

Sustainable and profitable grazing management in a highly variable environment-evidence and insights from a long term grazing trial in northern Australia.

Rainfall variability is a major challenge to sustainable management in semi-arid rangelands. We present empirical evidence from a large, long-term grazing trial in northern Australia on the relative performance of constant heavy stocking, moderate stocking at long-term carrying capacity and variable stocking in coping with climate variability over a range of rainfall years. Moderate stocking gave good economic returns, maintained pasture condition and minimised soil loss and runoff. Heavy stocking was neither sustainable nor profitable in the long term. Variable stocking generally performed well but suffered economic loss and some decline in pasture condition in the transition from good to poor years. Importantly, our results show that sustainable and profitable management are compatible in semi-arid rangelands.

Direct measurement of inner prosthesis loading during activities of daily living: Proposal for classification of functional outcome

Background The purpose of this presentation is to outline the relevance of the categorization of the load regime data to assess the functional output and usage of the prosthesis of lower limb amputees. The objectives are • To highlight the need for categorisation of activities of daily living • To present a categorization of load regime applied on residuum, • To present some descriptors of the four types of activity that could be detected, • To provide an example the results for a case. Methods The load applied on the osseointegrated fixation of one transfemoral amputee was recorded using a portable kinetic system for 5 hours. The load applied on the residuum was divided in four types of activities corresponding to inactivity, stationary loading, localized locomotion and directional locomotion as detailed in previously publications. Results The periods of directional locomotion, localized locomotion, and stationary loading occurred 44%, 34%, and 22% of recording time and each accounted for 51%, 38%, and 12% of the duration of the periods of activity, respectively. The absolute maximum force during directional locomotion, localized locomotion, and stationary loading was 19%, 15%, and 8% of the body weight on the anteroposterior axis, 20%, 19%, and 12% on the mediolateral axis, and 121%, 106%, and 99% on the long axis. A total of 2,783 gait cycles were recorded. Discussion Approximately 10% more gait cycles and 50% more of the total impulse than conventional analyses were identified. The proposed categorization and apparatus have the potential to complement conventional instruments, particularly for difficult cases.

Chloris gayana, Rhodes Grass 'KP4'

‘KP4’ is based on selected F4 progeny of 8 plants showing a low, creeping, tight-matted, late flowering growth habit. The original parental breeding population was selected from among 1600 diploid Rhodes grass seedlings grown as spaced plants; seven of the selected parental plants were from ‘Katambora’ and the eighth (which did not contribute as a maternal parent beyond the F1 generation) was a seedling from an unreleased accession. Four (4) cycles of mass selection were conducted, in which the selected plants from the previous generation were allowed to inter-cross in isolation in the field, and the resultant progeny later grown as spaced plants in the field for the next cycle of selection. Selection was for the following attributes: prostrate creeping early growth habit with short stolon internodes resulting in a dense stolon mat; leafy appearance; fine leaf and stem; and late flowering (i.e. a long period of vegetative growth before flowering). ‘KP4’ is a synthetic Rhodes grass cultivar multiplied from the selected fourth-generation plants produced by this line of breeding. Breeder: Donald S. Loch, Cleveland, QLD. PBR Certificate Number 3661, Application Number 2006/189, granted 16 December 2008

Continuation of limit cycles near saddle homoclinic points using splines in phase space

We present a new algorithm for continuation of limit cycles of autonomous systems as a system parameter is varied. The algorithm works in phase space with an ordered set of points on the limit cycle, along with spline interpolation. Currently popular algorithms in bifurcation analysis packages compute time-domain approximations of limit cycles using either shooting or collocation. The present approach seems useful for continuation near saddle homoclinic points, where it encounters a corner while time-domain methods essentially encounter a discontinuity (a relatively short period of rapid variation). Other phase space-based algorithms use rescaled arclength in place of time, but subsequently resemble the time-domain methods. Compared to these, we introduce additional freedom through a variable stretching of arclength based on local curvature, through the use of an auxiliary index-based variable. Several numerical examples are presented. Comparisons with results from the popular package, MATCONT, are favorable close to saddle homoclinic points.

The physiological and behavioral responses of steers to gaseous ammonia in simulated long distance transport by ship.

Ammonia (NH3) can accumulate in high density cattle accommodation during live export shipments and could potentially threaten the animals' health and welfare. The effects of 4 NH3 concentrations, control (<8), 15, 30, and 45 ppm, on the physiology and behavior of steers were recorded. The animals were held for 12 d under a micro-climate and stocking density similar to shipboard conditions experienced on voyages from Australia to the Middle East during the northern hemispheric summer. In bronchoalveolar lavage samples, ammonia increased (P < 0.05) macrophage activity in proportion to NH3 concentration and it increased (P < 0.05) neutrophil percentage at 30 and 45 ppm, indicating active pulmonary inflammation. It also increased (P < 0.05) lacrimation, nasal secretions and coughing, particularly at 45 ppm, indicating that the NH3 was irritating the mucous membranes of the eyes, nasal cavity and respiratory tract. Ammonia had no effect (P > 0.05) on hematological parameters or body weight. Twenty-eight days after exposure to NH3, the steers' pulmonary macrophage activity and neutrophil levels had returned to normal. It was concluded that ammonia concentrations of 30 and 45 ppm induced temporary inflammatory responses which indicate an adverse effect on the welfare of steers.

Wet-dry cycling extends seed persistence by re-instating antioxidant capacity

Seeds in the field experience wet-dry cycling that is akin to the well-studied commercial process of seed priming in which seeds are hydrated and then re-dried to standardise their germination characteristics. To investigate whether the persistence (defined as in situ longevity) and antioxidant capacity of seeds are influenced by wet-dry cycling, seeds of the global agronomic weed Avena sterilis ssp. ludoviciana were subjected to (1) controlled ageing at 60% relative humidity and 53.5°C for 31 days, (2) controlled ageing then priming, or (3) ageing in the field in three soils for 21 months. Changes in seed viability (total germination), mean germination time, seedling vigour (mean seedling length), and the concentrations of the glutathione (GSH) / glutathione disulphide (GSSG) redox couple were recorded over time. As controlled-aged seeds lost viability, GSH levels declined and the relative proportion of GSSG contributing to total glutathione increased, indicative of a failing antioxidant capacity. Subjecting seeds that were aged under controlled conditions to a wet-dry cycle (to −1 MPa) prevented viability loss and increased GSH levels. Field-aged seeds that underwent numerous wet-dry cycles due to natural rainfall maintained high viability and high GSH levels. Thus wet-dry cycles in the field may enhance seed longevity and persistence coincident with re-synthesis of protective compounds such as GSH.

Temporal genetic structure patterns in tropical maize populations under reciprocal recurrent selection.

In order to investigate the effect of long term recurrent selection on the pattern of gene diversity, thirty randomly-selected individuals from the progenitors (p) and four selection cycles (C0, C3, C6 and C11) were sampled for DNA analysis from the tropical maize (Zea mays L.) breeding populations, Atherton 1 (AT1) and Atherton 2 (AT2). Fifteen polymorphic Simple Sequence Repeat markers amplified a total of 284 and 257 alleles in AT1 and AT2 populations, respectively. Reductions in the number of alleles were observed at advanced selection cycles. About 11 and 12% of the alleles in AT1 and AT2 populations respectively, were near to fixation. However, a higher number of alleles (37% in AT1 and 33% in AT2) were close to extinction. Fisher's exact test and analysis of molecular variance (AMOVA) showed significant population differentiations. Gene diversity estimates and AMOVA revealed increased genetic differentiations at the expense of loss of heterozygosity. Population differentiations were mainly due to fixation of complementary alleles at a locus in the two breeding populations. The estimates of effective population at an advanced selection cycle were close to the population size predicted by the breeding method.