Reduction of seed production of red rice escapes in clearfield rice

Roguing is a practice used to reduce the seed source of red rice escapes to control in Clearfield-rice areas. However, there is great difficulty in performing it in large and heavily infested rice fields. This objective of this work was to evaluate the effects of the use of imazamox herbicide, applied in different rates and times, on plants of Clearfield-rice and red rice. Four experiments were conducted during the 2007/08 and 2008/09 growing seasons, in completely randomized block design and treatments arranged in factorial design, using three replications per treatment. The treatments had increasing rates of imazamox, application times and rice cultivars. The rice cultivars tested were IRGA 417, IRGA 422 CL, Avaxi CL and Puitá INTA CL. The variables evaluated were the number of panicles m-2, number of grains panicle-1, spikelet sterility in rice and red rice; and, rice grain yield and its components. The imazamox reduced the seed production of red rice escapes in a simulated situation of commercial Clearfield-rice area. The greater percentage reductions were obtained when this herbicide was applied at final formation of the panicle or panicle exertion of the red rice plant escapes to control. The Puitá INTA CL cultivar has high level of resistance to imazamox, independent of rate and application times tested, becoming the only alternative to the use of this practice.

Wind Turbine Direct-Drive Permanent-Magnet Generator with Direct Liquid Cooling for Mass Reduction

Today’s electrical machine technology allows increasing the wind turbine output power by an order of magnitude from the technology that existed only ten years ago. However, it is sometimes argued that high-power direct-drive wind turbine generators will prove to be of limited practical importance because of their relatively large size and weight. The limited space for the generator in a wind turbine application together with the growing use of wind energy pose a challenge for the design engineers who are trying to increase torque without making the generator larger. When it comes to high torque density, the limiting factor in every electrical machine is heat, and if the electrical machine parts exceed their maximum allowable continuous operating temperature, even for a short time, they can suffer permanent damage. Therefore, highly efficient thermal design or cooling methods is needed. One of the promising solutions to enhance heat transfer performances of high-power, low-speed electrical machines is the direct cooling of the windings. This doctoral dissertation proposes a rotor-surface-magnet synchronous generator with a fractional slot nonoverlapping stator winding made of hollow conductors, through which liquid coolant can be passed directly during the application of current in order to increase the convective heat transfer capabilities and reduce the generator mass. This doctoral dissertation focuses on the electromagnetic design of a liquid-cooled direct-drive permanent-magnet synchronous generator (LC DD-PMSG) for a directdrive wind turbine application. The analytical calculation of the magnetic field distribution is carried out with the ambition of fast and accurate predicting of the main dimensions of the machine and especially the thickness of the permanent magnets; the generator electromagnetic parameters as well as the design optimization. The focus is on the generator design with a fractional slot non-overlapping winding placed into open stator slots. This is an a priori selection to guarantee easy manufacturing of the LC winding. A thermal analysis of the LC DD-PMSG based on a lumped parameter thermal model takes place with the ambition of evaluating the generator thermal performance. The thermal model was adapted to take into account the uneven copper loss distribution resulting from the skin effect as well as the effect of temperature on the copper winding resistance and the thermophysical properties of the coolant. The developed lumpedparameter thermal model and the analytical calculation of the magnetic field distribution can both be integrated with the presented algorithm to optimize an LC DD-PMSG design. Based on an instrumented small prototype with liquid-cooled tooth-coils, the following targets have been achieved: experimental determination of the performance of the direct liquid cooling of the stator winding and validating the temperatures predicted by an analytical thermal model; proving the feasibility of manufacturing the liquid-cooled tooth-coil winding; moreover, demonstration of the objectives of the project to potential customers.

Nutrient cycling disturbance in Atlantic Forest sites affected by air pollution coming from the industrial complex of Cubatão, Southeast Brazil

Several aspects of nutrient cycling were studied at two sites of Atlantic Forest, in São Paulo State, Southeast Brazil (23o46’ S; 46o18’ W), which exhibited different degrees of forest structure decline caused by the air pollution emitted by the industrial complex of Cubatão, being referred here as the most and least affected sites (MAS and LAS, respectively). These investigations were developed during 1984 - 1986, a period in which the most severe negative effects of air pollution could be observed. Concentrations and amounts of N, P, K, Ca, Mg and S in four ecosystem compartments (leaves, litter layer, soil and roots) and in rainfall, throughfall and litterfall are briefly presented. At each site, the content of mineral elements generally decreased from leaves to litterfall and litter layer on the forest floor. Soil surface layer (0 - 5 cm) in both sites was the richest in mineral elements. Soil fertility was greater at LAS. In general, nutrient amounts remaining in the compartments and cycling through the ecosystem were greater at LAS as well, which could be due to the higher complexity of the forest structure at this site. Rainfall contributed more to soil inputs of K, Ca, Mg and S than litterfall at both sites. The nutrient residence times in the litter layer were higher and the index of nutrient use efficiency was lower at the most affected site. It was concluded that nutrient cycling was disturbed by air pollution at both sites, but to a greater extent at MAS. The main consequences of the air pollution stress were detected in the flux of nutrients through litterfall and in the litter layer on the forest floor.

The succession dynamics of a macroalgal community after a flood disturbance in a tropical stream from São Paulo State, southeastern Brazil

The succession dynamics of a macroalgal community in a tropical stream (20º58' S and 49º25' W) was investigated after disturbance by a sequence of intensive rains. High precipitation levels caused almost complete loss of the macroalgal community attached to the substratum and provided a strong pressure against its immediate re-establishment. After this disturbance, a weekly sampling program from May 1999 to January 2000 was established to investigate macroalgal recolonization. The community changed greatly throughout the succession process. The number of species varied from one to seven per sampling. Global abundance of macroalgal community did not reveal a consistent temporal pattern of variation. In early succession stages, the morphological form of tufts dominated, followed by unbranched filaments. Latter succession stages showed the almost exclusive occurrence of gelatinous forms, including filaments and colonies. The succession trajectory was mediated by phosphorus availability in which community composition followed a scheme of changes in growth forms. However, we believe that deterministic and stochastic processes occur in lotic ecosystems, but they are dependent on the length of time considered in the succession analyses.

Plant height reduction in populations of triticale (X triticosecale Wittmack) by induced mutations and artificial crosses

Induced mutations by gamma radiation (0, 5, 10, 20 and 40 kR doses) and reciprocal crosses were tested as mechanisms of enhancing genetic variability for plant height in two triticale cultivars, BR4 and EMBRAPA18. The reciprocal crosses and all doses of radiation showed similar increase in genetic amplitude for this trait, being suitable for increasing variability in breeding programs. Genotypes showed different responses as the gamma ray doses were increased, expressing shorter plant height. The decision of using induced mutations or artificial crosses depends on the resources available and the selection method to be used

Pre- and postnatal nutrition – target for allergy risk reduction

A rapid increase in allergic diseases in Western societies has led to the conclusion that our modern lifestyle is a risk factor for immune dysregulation. Potential culprits and benefactors are searched among early dietary and microbial exposures, which may act to program later allergic disease. The aim of this thesis was to investigate the role of early maternal and child nutrition in reducing the risk of child allergy. The study population comprised of 256 mother – child pairs from families with a history of allergy participating in a randomized controlled dietary counseling and probiotic intervention (Lactobacillus rhamnosus GG and Bifidobacterium lactis Bb12) study from early pregnancy onwards. The dietary counseling aimed for a diet complying with dietary recommendations for pregnant and lactating women, with special attention to fat quality. Maternal dietary counseling was reflected in cord blood fatty acids suggesting better essential fatty acid status in infants in the counseling group. Dietary counseling with probiotics or placebo had no effect on child allergy risk, but associations between maternal diet during pregnancy and breastfeeding and child allergic outcomes were found in secondary analyses. During pregnancy, milk intake was related to decreased and cheese intake to increased risk of child atopic eczema. During breastfeeding, intake of vitamin C was related to increased risk of asthma and intake of egg was related to decreased risk of atopic eczema. The timing of introduction of complementary foods to infant’s diet was not associated with risk of atopic eczema, when adjusted with parental opinion of child allergic symptoms (i.e., potential reverse causality). In conclusion, the results demonstrate that infant fatty acid supply can be modified via maternal dietary changes. In addition, interesting associations of maternal diet with child allergy risk were discovered. However, no difference in the incidence of allergic diseases with dietary counseling was observed. This suggests that more potent dietary interventions might be necessitated to induce clinical risk reduction of allergy. Highrisk families can safely adhere to dietary recommendations for pregnant and lactating women, and the results support the current conception that no additional benefit is gained with delaying introduction of complementary feeding.

Sleep patterns and sleep-related complaints of Brazilian interstate bus drivers

Sleep-related complaints have become a highlight for physicians as well as public health administrators. Studies of sleep patterns and sleep-related complaints of shift workers have been useful in minimizing reduction in the quality of life due to the warping of the sleep-wake cycle. The objective of the present study was to assess patterns of sleep, sleep-related complaints as well as physical activity and scoring rates for depression and anxiety in interstate bus drivers. Data were obtained with a sleep questionnaire, with the Beck inventory for depression, and the State-Trait Anxiety Inventory (STAI). A total of 400 interstate bus drivers from the northern, southern, central-western and south-eastern regions of Brazil were interviewed. Sixty percent of the subjects interviewed presented at least one sleep-related complaint, 16% admitted to have dozed at the wheel while on duty, and 41% stated that they exercised on a regular basis. Other sleep disturbance complaints reported were: sleep latency 29'17"; physical fatigue, 59.8%; mental fatigue, 45.4%; sleepiness, 25.8%; irritability, 20.6%; insomnia, 37.5%, respiratory disturbances, 19.25% and snoring, 20.75%. Scores for anxiety and depression were not in the pathological range. The present data reinforce the view that bus drivers are generally discontent with shift work and its effects on sleep. Consequently, it is very important to establish an appropriate work schedule for drivers, besides implementing photo-therapy and physical activities in order to minimize sleepiness when driving.

Strategic planning of major disturbance proof network

In the 2000’s Finland suffered from storms that caused long outages in electricity distribution, longest up to two weeks. These major disturbances increased the importance of supply security. In 2013 new Electricity Market Act was announced. It defined maximum duration for outages, 6 h for city plan areas and 36 h for other areas. The aim for this work is to determine required major disturbance proof level for a study area and find tools for prioritizing overhead lines for cabling renovation to improve supply security. Three prioritization methods were chosen to be studied: A: prioritization line sections by customer outage costs they cause, B: maximizing customers major disturbance proof network and C: minimizing excavation costs in medium voltage network. Profitability calculations showed that prioritization method A was the most profitable and C had the weakest profitability. The prioritization method C drove renovation into unreasonable locations in the study area in reliability point of view. Therefore universal rule prioritization methods couldn’t be made from the prioritization methods. This led to the conclusion that every renewing area need to be evaluated in a case by case basis.

Reduction of nitrogen oxide emissions in lime kiln

Different nitrogen oxide removal technologies for rotary lime kiln are studied in this thesis, the main focus being in commercial technologies. Post-combustion methods are investigated in more detail as potential possible NOx removal with combustion methods in rotary lime kiln is more limited or primary methods are already in use. However, secondary methods as NOx scrubber, SNCR or SCR technologies are not listed as the Best Available Technologies defined by European Union. BAT technologies for NOx removal in lime kiln are (1) Optimised combustion and combustion control, (2) Good mixing of fuel and air, (3) Low-NOx burner and (4) Fuel selection/low-N fuel. SNCR method is the most suitable technique for NOx removal in lime kiln when NOx removal from 50 % to 70 % is required in case primary methods are already in use or cannot be applied. In higher removal cases ammonia slip is an issue in SNCR. By using SCR better NOx reduction can be achieved but issues with catalyst materials are expected to arise because of the dust and sulphur dioxide which leads to catalyst poison formation in lower flue gas temperatures. NOx scrubbing has potential when simultaneous NOx and SO2 removal is required. The challenge is that NO cannot be scrubbed directly, but once it is oxidized to NO2 or further scrubbing can be performed as the solubility of NO2 is higher. Commercial installations have not been made regarding SNCR, SCR or NOx scrubbing regarding rotary lime kiln. For SNCR and SCR the closest references come from cement industry.

Reduction of intraspecific aggression in adult rats by neonatal treatment with a selective serotonin reuptake inhibitor

Most studies suggest that serotonin exerts an inhibitory control on the aggression process. According to experimental evidence, this amine also influences growth and development of the nervous tissue including serotoninergic neurons. Thus, the possibility exists that increased serotonin availability in young animals facilitates a long-lasting effect on aggressive responses. The present study aimed to investigate the aggressive behavior of adult rats (90-120 days) treated from the 1st to the 19th postnatal day with citalopram (CIT), a selective serotonin reuptake inhibitor (20 mg/kg, sc, every 3 days). Aggressive behavior was induced by placing a pair of rats (matched by weight) in a box (20 x 20 x 20 cm), and submitting them to a 20-min session of electric footshocks (five 1.6-mA - 2-s current pulses, separated by a 4-min intershock interval). When compared to the control group (rats treated for the same period with equivalent volumes of saline solution), the CIT group presented a 41.4% reduction in the duration of aggressive response. The results indicate that the repeated administration of CIT early in life reduces the aggressive behavior in adulthood and suggest that the increased brain serotoninergic activity could play a role in this effect.

Immune and hormonal activity in adults suffering from depression

An association between depression and altered immune and hormonal systems has been suggested by the results of many studies. In the present study we carried out immune and hormonal measurements in 40 non-medicated, ambulatory adult patients with depression determined by CID-10 criteria and compared with 34 healthy nondepressed subjects. The severity of the condition was determined with the Hamilton Depression Rating Scale. Of 40 depressed patients, 31 had very severe and 9 severe or moderate depression, 29 (72.5%) were females and 11 (27.5%) were males (2.6:1 ratio). The results revealed a significant reduction of albumin and elevation of alpha-1, alpha-2 and ß-globulins, and soluble IL-2 receptor in patients with depression compared to the values obtained for nondepressed subjects (P<0.05). The decrease lymphocyte proliferation in response to a mitogen was significantly lower in severely or moderately depressed patients when compared to control (P<0.05). These data confirm the immunological disturbance of acute phase proteins and cellular immune response in patients with depression. Other results may be explained by a variety of interacting factors such as number of patients, age, sex, and the nature, severity and/or duration of depression. Thus, the data obtained should be interpreted with caution and the precise clinical relevance of these findings requires further investigation.

Transitory increased blood pressure after upper airway surgery for snoring and sleep apnea correlates with the apnea-hypopnea respiratory disturbance index

A transitory increase in blood pressure (BP) is observed following upper airway surgery for obstructive sleep apnea syndrome but the mechanisms implicated are not yet well understood. The objective of the present study was to evaluate changes in BP and heart rate (HR) and putative factors after uvulopalatopharyngoplasty and septoplasty in normotensive snorers. Patients (N = 10) were instrumented for 24-h ambulatory BP monitoring, nocturnal respiratory monitoring and urinary catecholamine level evaluation one day before surgery and on the day of surgery. The influence of postsurgery pain was prevented by analgesic therapy as confirmed using a visual analog scale of pain. Compared with preoperative values, there was a significant (P < 0.05) increase in nighttime but not daytime systolic BP (119 ± 5 vs 107 ± 3 mmHg), diastolic BP (72 ± 4 vs 67 ± 2 mmHg), HR (67 ± 4 vs 57 ± 2 bpm), respiratory disturbance index (RDI) characterized by apnea-hypopnea (30 ± 10 vs 13 ± 4 events/h of sleep) and norepinephrine levels (22.0 ± 4.7 vs 11.0 ± 1.3 µg l-1 12 h-1) after surgery. A positive correlation was found between individual variations of BP and individual variations of RDI (r = 0.81, P < 0.01) but not between BP or RDI and catecholamines. The visual analog scale of pain showed similar stress levels on the day before and after surgery (6.0 ± 0.8 vs 5.0 ± 0.9 cm, respectively). These data strongly suggest that the cardiovascular changes observed in patients who underwent uvulopalatopharyngoplasty and septoplasty were due to the increased postoperative RDI.

Unequal Teeth Widths for Torque Ripple Reduction in Permanent Magnet Synchronous Machines With Fractional-Slot Non-Overlapping Windings

Permanent magnet synchronous machines with fractional-slot non-overlapping windings (FSPMSM), also known as tooth-coil winding permanent magnet synchronous machines (TCW PMSM), have been under intensive research during the latest decade. There are many optimization routines explained and implemented in the literature in order to improve the characteristics of this machine type. This paper introduces a new technique for torque ripple minimization in TCW PMSM. The source of torque harmonics is also described. The low order torque harmonics can be harmful for a variety of applications, such as direct drive wind generators, direct drive light vehicle electrical motors, and for some high precision servo applications. The reduction of the torque ripple harmonics with the lowest orders (6th and 12th) is realized by machine geometry optimization technique using finite element analysis (FEA). The presented optimization technique includes the stator geometry adjustment in TCW PMSMs with rotor surface permanent magnets and with rotor embedded permanent magnets. Influence of the permanent magnet skewing on the torque ripple reduction and cogging torque elimination was also investigated. It was implemented separately and together with the stator optimization technique. As a result, the reduction of some torque ripple harmonics was attained.

Oral triiodothyronine for the prevention of thyroid hormone reduction in adult valvular cardiac surgery

Treatment of non-thyroidal illness by intravenous triiodothyronine (T3) after cardiac surgery causes a disproportional elevation of hormone levels. The administration of oral T3, which has never been studied in this context, could cause physiological hormone levels. The aim of this study was to test oral T3 for the prevention of T3 reduction during the postoperative period of valvular cardiac surgery in adults. Eighteen patients who underwent cardiac surgery for valvular disease with invasive hemodynamic monitoring were randomly assigned to 2 groups: the T group received oral T3 (N = 8), 25 µg three times/day, initiated 24 h before surgery and maintained for 48 h and the NT group (N = 10) received placebo. Serum T3, thyroxine and thyrotropin were determined at baseline, 1 h before surgery, within 30 min of cardiopulmonary bypass and 6, 12, 24, and 48 h after removal of the aortic cross-clamp. Baseline T3 was similar in both groups (T: 119 ± 13; NT: 131 ± 9 ng/dL). Serum T3 increased during the first 24 h in the T group compared to the NT group (232 ± 18 vs 151 ± 13 ng/dL; P < 0.001). In the NT group, T3 was reduced by 24% (P = 0.007) 6 h after removal of the aortic cross-clamp, confirming the non-thyroidal illness syndrome. There were no differences in clinical or hemodynamic parameters between groups. Administration of oral T3 prevented its serum reduction after valvular cardiac surgery in adults, with normal serum levels for 48 h without disproportional elevations.

Cost Reduction of Permanent Magnet Synchronous Machines

Electrical machine drives are the most electrical energy-consuming systems worldwide. The largest proportion of drives is found in industrial applications. There are, however many other applications that are also based on the use of electrical machines, because they have a relatively high efficiency, a low noise level, and do not produce local pollution. Electrical machines can be classified into several categories. One of the most commonly used electrical machine types (especially in the industry) is induction motors, also known as asynchronous machines. They have a mature production process and a robust rotor construction. However, in the world pursuing higher energy efficiency with reasonable investments not every application receives the advantage of using this type of motor drives. The main drawback of induction motors is the fact that they need slipcaused and thus loss-generating current in the rotor, and additional stator current for magnetic field production along with the torque-producing current. This can reduce the electric motor drive efficiency, especially in low-speed, low-power applications. Often, when high torque density is required together with low losses, it is desirable to apply permanent magnet technology, because in this case there is no need to use current to produce the basic excitation of the machine. This promotes the effectiveness of copper use in the stator, and further, there is no rotor current in these machines. Again, if permanent magnets with a high remanent flux density are used, the air gap flux density can be higher than in conventional induction motors. These advantages have raised the popularity of PMSMs in some challenging applications, such as hybrid electric vehicles (HEV), wind turbines, and home appliances. Usually, a correctly designed PMSM has a higher efficiency and consequently lower losses than its induction machine counterparts. Therefore, the use of these electrical machines reduces the energy consumption of the whole system to some extent, which can provide good motivation to apply permanent magnet technology to electrical machines. However, the cost of high performance rare earth permanent magnets in these machines may not be affordable in many industrial applications, because the tight competition between the manufacturers dictates the rules of low-cost and highly robust solutions, where asynchronous machines seem to be more feasible at the moment. Two main electromagnetic components of an electrical machine are the stator and the rotor. In the case of a conventional radial flux PMSM, the stator contains magnetic circuit lamination and stator winding, and the rotor consists of rotor steel (laminated or solid) and permanent magnets. The lamination itself does not significantly influence the total cost of the machine, even though it can considerably increase the construction complexity, as it requires a special assembly arrangement. However, thin metal sheet processing methods are very effective and economically feasible. Therefore, the cost of the machine is mainly affected by the stator winding and the permanent magnets. The work proposed in this doctoral dissertation comprises a description and analysis of two approaches of PMSM cost reduction: one on the rotor side and the other on the stator side. The first approach on the rotor side includes the use of low-cost and abundant ferrite magnets together with a tooth-coil winding topology and an outer rotor construction. The second approach on the stator side exploits the use of a modular stator structure instead of a monolithic one. PMSMs with the proposed structures were thoroughly analysed by finite element method based tools (FEM). It was found out that by implementing the described principles, some favourable characteristics of the machine (mainly concerning the machine size) will inevitable be compromised. However, the main target of the proposed approaches is not to compete with conventional rare earth PMSMs, but to reduce the price at which they can be implemented in industrial applications, keeping their dimensions at the same level or lower than those of a typical electrical machine used in the industry at the moment. The measurement results of the prototypes show that the main performance characteristics of these machines are at an acceptable level. It is shown that with certain specific actions it is possible to achieve a desirable efficiency level of the machine with the proposed cost reduction methods.