722 resultados para steam consumption
Resumo:
In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.
Resumo:
The complexity of the connexions within an economic system can only be reliably reflected in academic research if powerful methods are used. Researchers have used Structural Path Analysis (SPA) to capture not only the linkages within the production system but also the propagation of the effects into different channels of impacts. However, the SPA literature has restricted itself to showing the relations among sectors of production, while the connections between these sectors and final consumption have attracted little attention. In order to consider the complete set of channels involved, in this paper we propose a structural path method that endogenously incorporates not only sectors of production but also the final consumption of the economy. The empirical application comprises water usages, and analyses the dissemination of exogenous impacts into various channels of water consumption. The results show that the responsibility for water stress is imputed to different sectors and depends on the hypothesis used for the role played by final consumption in the model. This highlights the importance of consumers’ decisions in the determination of ecological impacts. Keywords: Input-Output Analysis, Structural Path Analysis, Final Consumption, Water uses.
Resumo:
The water consumption and the crop coefficient of the banana cv. Pacovan were estimated in Petrolina County, northeastern Brazil, in order to establish guidelines to irrigation water management. Evaluations were carried out since planting in January 1999 to the 3rd harvest in September 2001 on a microsprinkler irrigated orchard, with plants spaced in a 3 x 3 m grid. Average daily water consumption was 3.9, 4.0, and 3.3 mm in the 1st, 2nd and 3rd growing seasons, respectively. Crop coefficient values increased from 0.7 (vegetative growth) to 1.1 (flowering). Even with high soil water availability, transpiration was reduced due to high evaporative demand.
Resumo:
Background: There are few studies comparing pharmaceutical costs and the use of medications between immigrants and the autochthonous population in Spain. The objective of this study is to evaluate whether there are differences in pharmaceutical consumption and expenses between immigrant and Spanish-born populations. Methods: Prospective observational study in 1,630 immigrants and 4,154 Spanish-born individuals visited by fifteen primary care physicians at five public Primary Care Clinics (PCC) during 2005 in the city of Lleida, Catalonia (Spain). Data on pharmaceutical consumption and expenses was obtained from a comprehensive computerized data-collection system. Multinomial regression models were used to estimate relative risks and confidence intervals of pharmaceutical expenditure, adjusting for age and sex. Results: The percentage of individuals that purchased medications during a six-month period was 53.7% in the immigrant group and 79.2% in the autochthonous group. Pharmaceutical expenses and consumption were lower in immigrants than in autochthonous patients in all age groups and both genders. The relative risks of being in the highest quartile of expenditure, for Spanish-born versus immigrants, were 6.9, 95% CI = (4.2, 11.5) in men and 5.3, 95% CI = (3.5, 8.0) in women, with the reference category being not having any pharmaceutical expenditure. Conclusion: Pharmaceutical expenses are much lower for immigrants with respect to autochthonous patients, both in the percentage of prescriptions filled at pharmacies and the number of containers of medication obtained, as well as the prices of the medications used. Future studies should explore which factors explain the observed differences in pharmaceutical expenses and if these disparities produce health inequalities.
Resumo:
BACKGROUND: Health professionals and organizations in developed countries adapt slowly to the increase of ethnically diverse populations attending health care centres. Several studies report that attention to immigrant mental health comes up with barriers in access, diagnosis and therapeutics, threatening equity. This study analyzes differences in exposure to antidepressant drugs between the immigrant and the native population of a Spanish health region. METHODS: Cross-sectional study of the dispensation of antidepressant drugs to the population aged 15 years or older attending the public primary health centres of a health region, 232,717 autochthonous and 33,361 immigrants, during 2008. Data were obtained from computerized medical records and pharmaceutical records of medications dispensed in pharmacies. Age, sex, country of origin, visits, date of entry in the regional health system, generic drugs and active ingredients were considered. Statistical analysis expressed the percentage of persons exposed to antidepressants stratified by age, gender, and country of origin and prevalence ratios of antidepressant exposition were calculated. RESULTS: Antidepressants were dispensed to 11% of native population and 2.6% of immigrants. Depending on age, native women were prescribed antidepressants between 1.9 and 2.7 times more than immigrant women, and native men 2.5 and 3.1 times more than their immigrant counterparts. Among immigrant females, the highest rate was found in the Latin Americans (6.6%) and the lowest in the sub-Saharans (1.4%). Among males, the highest use was also found in the Latin Americans (1.6%) and the lowest in the sub-Saharans (0.7%). The percentage of immigrants prescribed antidepressants increased significantly in relation to the number of years registered with the local health system. Significant differences were found for the new antidepressants, prescribed 8% more in the native population than in immigrants, both in men and in women. CONCLUSIONS: All the immigrants, regardless of the country of origin, had lower antidepressant consumption than the native population of the same age and sex. Latin American women presented the highest levels of consumption, and the sub-Saharan men the lowest. The prescription profiles also differed, since immigrants consumed more generics and fewer recently commercialized active ingredients.
Resumo:
The objective of this thesis is to find out how information and communication technology affects the global consumption of printing and writing papers. Another objective is to find out, whether there are differences between paper grades in these effects. The empirical analysis is conducted by linear regression analysis using three sets of country-level panel data from 1990-2006. Data set of newsprint contains 95 countries, data set of uncoated woodfree paper 61 countries and data set of coated mechanical paper 42 countries. The material is based on paper consumption data of RISI’s Industry Statistics Database and on the information and communication technology data of GMID-database. Results indicate that number of Internet users has statistically significant negative effect on the consumption of newsprint and on the consumption of coated mechanical paper and number of mobile telephone users has positive effect on the consumptions of these papers. Results also indicate that information and communication technologies have only small effect on consumption of uncoated woodfree paper or no significant effect at all, but these results are more uncertain to some extent.
Resumo:
Coffee, a major dietary source of caffeine, is among the most widely consumed beverages in the world and has received considerable attention regarding health risks and benefits. We conducted a genome-wide (GW) meta-analysis of predominately regular-type coffee consumption (cups per day) among up to 91 462 coffee consumers of European ancestry with top single-nucleotide polymorphisms (SNPs) followed-up in ~30 062 and 7964 coffee consumers of European and African-American ancestry, respectively. Studies from both stages were combined in a trans-ethnic meta-analysis. Confirmed loci were examined for putative functional and biological relevance. Eight loci, including six novel loci, met GW significance (log10Bayes factor (BF)>5.64) with per-allele effect sizes of 0.03-0.14 cups per day. Six are located in or near genes potentially involved in pharmacokinetics (ABCG2, AHR, POR and CYP1A2) and pharmacodynamics (BDNF and SLC6A4) of caffeine. Two map to GCKR and MLXIPL genes related to metabolic traits but lacking known roles in coffee consumption. Enhancer and promoter histone marks populate the regions of many confirmed loci and several potential regulatory SNPs are highly correlated with the lead SNP of each. SNP alleles near GCKR, MLXIPL, BDNF and CYP1A2 that were associated with higher coffee consumption have previously been associated with smoking initiation, higher adiposity and fasting insulin and glucose but lower blood pressure and favorable lipid, inflammatory and liver enzyme profiles (P<5 × 10-8).Our genetic findings among European and African-American adults reinforce the role of caffeine in mediating habitual coffee consumption and may point to molecular mechanisms underlying inter-individual variability in pharmacological and health effects of coffee.
Resumo:
Tässä työssä on selvitetty sellutehtaan höyryverkosta tehtaan ulkopuolelle myytävän ylijäämähöyryn määrän ja paineen nopeaan vaihteluun vaikuttavia tekijöitä. Työssä on tarkasteltu höyryn kehityksen ja kulutuksen vaihtelun vaikutusta ylijäämähöyryyn. Lisäksi on tarkasteltu mahdollisuuksia edellä mainittujen häiriöiden tasaamiseksi. Työssä on selvitetty teoriaa, joka vaikuttaa sellutehtaan höyryn kehitykseen ja kulutukseen. Lisäksi on selvitetty energiataselaskennan ja höyryverkon hallintaa parantavien toimenpiteiden teoriaa. Omana kokonaisuutena on sellutehtaan höyryn kehityksen ja kulutuksen tarkastelu sekä selvitys tehtaan höyryverkon hallinnan nykytilasta. Höyryverkolle on muodostettu energiatase. Työn tuloksia varten on kerätty ja tallennettu mittapistetietoa tiedonkeräysjärjestelmän avulla eri höyryverkon mittapisteistä. Työn tuloksina on mainittu useita höyryverkon hallintaa parantavia toteutuskelpoisia asioita ja toimenpiteitä. Työllä on luotu pohjaa menetelmälle, joka ohjaa energian kehitystä vastaamaan sellun tuotannon tarvitsemaa energiamäärää. Samalla saataisiin paremmin hallittua ylijäämähöyryä ja sen määrän sekä paineen vaihtelu vähentyisi.
Resumo:
Tässä diplomityössä on suunniteltu ja toteutettu tuotannon optimointijärjestelmä Kotkan Energia Oy:n tuotantolaitoksille sekä osto- ja myyntisopimuksille. Työssä on kerätty ja laskettu Kotkan Energian tuotantolaitosten teknisiä ja suunnittelutietoja, sekä esitelty eri laitteiden ja tuotantolaitosten toimintaa. Lisäksi on käyty läpi kaukolämmön ja prosessihöyryn kulutusta, kulutuksien ennustamista ja tuotantojärjestelmiä, sekä sähkökauppaa ja laitoksilla käytettävien polttoaineiden ominaisuuksia ja hintoja. Voimalaitoksen laitteille on laskettu hyötysuhteet ja tuotteiden hinnat erilaisilla kuormilla. Laskelmien avulla on tehty polynomisovitteet laitteiden hyötysuhteille. Polynomisovitteet ja muu laitosten toiminnasta kerätty ja laskettu tieto on siirretty Kotkan Energian tietohallintopäällikön kanssa yhteistyössä kehitettyyn tietokonepohjaiseen optimointiohjelmaan. Myös optimoinnin teoriaa ja menetelmiä on käyty lyhyesti läpi. Optimointiohjelman avulla pystytään nyt laskemaan erilaisten kaukolämmön, prosessihöyryn ja sähkön hintojen ja kulutusten mukaisia optimaalisia ajotapoja Hovinsaaren voimalaitoksen tuotannolle ja hankintasopimuksille. Optimointiohjelmalla pyritään maksimoimaan energiantuotannon kokonaistuottoa tai minimoimaan tuotantokustannuksia annettujen ja ennustettujen alkuarvojen mukaisesti. Ohjelman antamia tuloksia voidaan käyttää apuna esimerkiksi tuotannon suunnittelussa ja budjetoinnissa. Laskelmat ja ohjelman kehittäminen ovat onnistuneet hyvin ja ohjelman käyttämisestä ja testaamisesta saadut tulokset vaikuttavat oikeanlaisilta ja luotettavilta. Optimointiohjelma on nyt käytössä ja jatkokehittely jatkuu myös diplomityön valmistumisen jälkeen.
Resumo:
Työn tavoitteena on Stora Enso Oyj:n Imatran tehtaiden energiaraportoinnin luotettavuuden parantaminen. Raportoinnissa esiintyvää tase-eroa lämmön tuotannon ja kulutuksen välillä on erilaisten selvitysten perusteella pyritty pienentämään. Höyryn ja lauhteen mittausten virheellisyyttä on tutkittu erilaisten osasto- ja höyrylinja- kohtaisten lämpötaseiden avulla. Taseiden lisäksi mittauksen oikeellisuutta selvitettäessä on käytetty tunnuslukuina lämmön ominaiskulutuksia, joita on verrattu Suomen metsäteollisuuden keskimääräisiin arvoihin. Työssä on tarkistettu myös raportointijärjestelmän laskenta ja päivitetty tarvittavat muutokset. Osa raportoinnin tase-erosta johtuu höyryn virtausmittauksen epävarmuudesta. Tässä työssä on esitetty erilaisia vaihtoehtoja sille, mistä mittauksen epävarmuus johtuu. Samalla on selvitetty virtausmittauksen periaatetta ja siihen tarvittavaa laitteistoa.
Resumo:
Mulching has become an important technique for land cover, but there are some technical procedures which should be adjusted for these new modified conditions to establish optimum total water depth. It is also important to observe the soil-water relations as soil water distribution and wetted volume dimensions. The objective of the present study was to estimate melon evapotranspiration under mulching in a protected environment and to verify the water spatial distribution around the melon root system in two soil classes. Mulching provided 27 mm water saving by reducing water evaporation. In terms of volume each plant received, on average, the amount of 175.2 L of water in 84 days of cultivation without mulching, while when was used mulching the water requirement was 160.2 L per plant. The use of mulching reduced the soil moisture variability throughout the crop cycle and allowed a greater distribution of soil water that was more intense in the clay soil. The clayey soil provided on average 43 mm more water depth retention in 0.50 m soil deep relative to the sandy loam soil, and reduced 5.6 mm the crop cycle soil moisture variation compared to sandy loam soil.
Resumo:
[cat] En aquest treball s'analitza l'efecte que comporta l'introducció de preferències inconsistents temporalment sobre les decisions òptimes de consum, inversió i compra d'assegurança de vida. En concret, es pretén recollir la creixent importància que un individu dóna a la herència que deixa i a la riquesa disponible per a la seva jubilació al llarg de la seva vida laboral. Amb aquesta finalitat, es parteix d'un model estocàstic en temps continu amb temps final aleatori, i s'introdueix el descompte heterogeni, considerant un agent amb una distribució de vida residual coneguda. Per tal d'obtenir solucions consistents temporalment es resol una equació de programació dinàmica no estàndard. Per al cas de funcions d'utilitat del tipus CRRA i CARA es troben solucions explícites. Finalment, els resultats obtinguts s'il·lustren numèricament.
Resumo:
[cat] En aquest treball s'analitza l'efecte que comporta l'introducció de preferències inconsistents temporalment sobre les decisions òptimes de consum, inversió i compra d'assegurança de vida. En concret, es pretén recollir la creixent importància que un individu dóna a la herència que deixa i a la riquesa disponible per a la seva jubilació al llarg de la seva vida laboral. Amb aquesta finalitat, es parteix d'un model estocàstic en temps continu amb temps final aleatori, i s'introdueix el descompte heterogeni, considerant un agent amb una distribució de vida residual coneguda. Per tal d'obtenir solucions consistents temporalment es resol una equació de programació dinàmica no estàndard. Per al cas de funcions d'utilitat del tipus CRRA i CARA es troben solucions explícites. Finalment, els resultats obtinguts s'il·lustren numèricament.