Influência do lodo de ETE na massa para fabricação de cerâmica vermelha

The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible

Caracterização termo-mecânica de interconectores metálicos recobertos com filmes de LaCrO3

The cells unitaria of the solid oxide fuel cell are separated by means of interconnects, which serve as electrical contact between the cells. Lanthanum Chromite (LaCrO3) has been the most common material used as interconnect in solid oxide fuel cells. Reducing the operating temperature around 800 º C of cells to solid oxide fuel make possibilite the use of metallic interconnects as an alternative to ceramic LaCrO3. Metallic interconnects have advantages over ceramic interconnects such as high thermal conductivity, electricity, good ductility, low cost, good physical and mechanical properties. In this work evaluate the thermo-mechanical properties of the metallic substrate and coated metallic substrate with the ceramic LaCrO3 film via spray-pyrolysis, in order to demonstrate the feasibility of using this material as a component of a fuel cell solid oxide. The materials were characterized by X-ray diffraction, oxidation behavior, mechanical strength, optical microscopy (OM) and scanning electron microscopy (SEM). The X-ray diffraction proved the formation phase of the LaCrO3 on the metallic substrate and the identification of the phases formed after the oxidative test and mechanical strength at high temperature. The oxidation behavior showed the increased oxidation resistance of the coated metallic substrate. It was noted that the mechanical resistance to bending of the coated metallic substrate only increases at room temperature. The optical microscopy (OM) has provided an assessment of both the metallic substrate and the LaCrO3 film deposited on the metal substrate that, in comparison with the micrographs obtained from SEM. The SEM one proved the formation of Cr2O3 layer on the metallic substrate and stability of LaCrO3 film after oxidative test, it can also observe the displacement of the ceramic LaCrO3 film after of mechanical testing and mapping of the main elements as chromium, manganese, oxygen, lanthanum in samples after the thermo-mechanical tests.

Uso de resíduo e de minerais de pegmatito da região do seridó RN e de argilas portuguesas em formulações de grês porcelanato

In the State Rio Grande do Norte, Brazil, the most significant deposits of minerals in the production of granite and pegmatite are Seridó region. Municipalities of Parelhas and Equador are the main responsible for the production of feldspar, quartz, kaolin and granite. The ceramic industries are always in search of competitiveness by investing in new products or improving existing techniques. The stoneware is a type of pottery that stands in the market because it presents technical and aesthetic characteristics superior to other existing products. Characteristics of the raw materials initially obtained with chemical analysis and mineralogical analysis are crucial in getting a product that satisfies the conditions in a manufacturing process and is, in principle, directly related to the firing cycle. This research aimed at developing new formulations for the mass production of ceramic stoneware. The raw materials initially characterized were feldspar, quartz, kaolin and granite. As part of the research was developed at the University of Aveiro, in Portugal, we used two clays used in the production of Portuguese ceramics. The raw material Brazilian and Portuguese and the final product, both in Portugal and Brazil, were analyzed for X-ray fluorescence, X-ray diffraction, granulometric analysis, dilatometric analysis, thermal analysis and analysis of scanning electron microscopy (MEV). The specimens prepared at the University of Aveiro (DECV) were sintered at 10000C and 12000C and the specimens prepared in UFRN were sintered at 10000C, 10500C, 11000C, 11500C, 12000C, 12500C and 13000C, but the best results and demonstrating the presence of the mineral mullite were at temperatures of 12000C, 12500C and 13000C. The results showed that the granite waste used may be considered raw material of excellent quality for use in the ceramic industry and coating floors and more accurately by the industry of stoneware. Physical and mechanical tests conducted on samples of the formulations F01 and F02 developed in UFRN showed a water absorption and mechanical strength suitable for the stoneware

Estudo da substituição de agregados miúdos naturais por pó de pedra em concreto de cimento portland

The sharp consumption of natural resources by the construction industry has motivated numerous studies concerning the application of waste to replace partially or fully, some materials, such as aggregates, thereby reducing the environmental impact caused by the extraction of sand and crushing process. The application of stone dust from crushing process arising as an aggregate for the production of Portland cement concrete is a viable alternative in view of the high cost of natural sands, in addition to the environmental damage which causes its operation to the environment. The stone dust has reduced cost compared to natural sand because it is produced in the beds of their own quarries, which are usually located close to major urban centers. This study examined the feasibility of using stone dust from the crushing of rock gneisses in the state of Bahia, replacing natural quartz sand. In the development of scientific study was conducted to characterize physical and chemical raw materials applied and molded cylindrical specimens , using as reference values Fck 20, Fck 25 and Fck 30 MPa ( resistance characteristic of the concrete after 28 days) in following compositions stone powder: 10%, 30%, 50 %, 100% and 100% with additive. The specimens were cured and subjected to the tests of compressive strength and water absorption, then the samples were subjected to the tests of X-ray diffraction and scanning electron microscopy. The results obtained showed that the composition with 10% stone powder showed the best results regarding the physical and mechanical tests performed, confirming the reduction in compressive strength and increased water uptake increased as the content of the powder stone in the concrete composition

Adição de subprodutos da cinza da casca de café (coffea canephora) em massa cerâmica para porcelanato

To produce porcelain tiles fluxing agents are used in order to obtain a liquid phase during firing. This liquid phase fills the pores decreasing porosity, water absorption and contributes to material densification. In the porcelain tiles industry, feldspar is the main flux material used, with quantities ranging between 35 and 50%. Studies focus on the discovery of materials with flux characteristics that can reduce the consumption of feldspar by porcelain tiles industry. In this context, the coffee husk ashes, a residue obtained when coffee husks are burned to produce heat for the dryers during the processing of the green fruit, have as main chemical constituents potassium, calcium and magnesium, giving them characteristics of fluxing material. Brazil is the largest coffee producer in the world and is responsible for over 30% of the world s production. In this work a physical treatment of coffee husk ash was carried out in order to eliminate the organic matter and, after this, two by-products were obtained: residual wastes R1 and R2. Both residues were added separately as single fluxes and also in association with feldspar in mixtures with raw materials collected in a porcelain industry located in Dias d Ávila-Ba. The addition of these residues aimed to contribute to the reduction of the consumption of feldspar in the production of porcelain tiles. Specimens were produced with dimensions of 60 mm x 20 mm x 6 mm in an uniaxial die with compacting pressure of 45 MPa. The samples were heated to a temperature of 1200 °C, for 8 minutes. Tests were performed to characterize the raw materials by XRF, XRD, particle size analysis, DTA and TGA and, additionally, the results of the physical properties of water absorption, apparent porosity, linear shrinkage, density, dilatometry, flexural strength and SEM of sintered body were analyzed. Additions of less than 8% of the residue R1 contributed to the decrease of porosity, but the mechanical strength of the samples was not satisfactory. Additions of 5% the R2 residue contributed significantly to decrease the water absorption and apparent porosity, and also to increase the mechanical strength. Samples with addition of feldspar associated with the R2 residue, in proportions of 6.7% of R2 and 6.7% of feldspar, led to results of water absorption of 0.12% and mechanical strength of 46 MPa, having parameters normalized to the manufacture of porcelain stoneware tiles

Avaliação do potencial de formigas (Hymenoptera: formicidae) como vetores mecânicos de bactérias do gêneroSstaphylococcus no ambiente hospitalar.

In a hospital environment, these bacteria can be spread by insects such as ants, which are characterized by high adaptability to the urban environment. Staphylococcus is a leading cause of hospital infection. In Europe, Latin America, USA and Canada, the group of coagulase negative staphylococci (CoNS) is the second leading cause of these infections, according to SENTRY (antimicrobial surveillance program- EUA). In this study, we investigated the potential of ants (Hymenoptera: Formicidae) as vehicle mechanics of Staphylococcus bacteria in a public hospital, in Natal-RN. The ants were collected, day and night, from June 2007 to may 2008, in the following sectors: hospitals, laundry, kitchen, blood bank. The ants were identified according to the identification key of Bolton, 1997. For the analysis of staphylococci, the ants were incubated in broth Tryptic Soy Broth (TSB) for 24 hours at 35 º C and then incubated on Mannitol Salt Agar. The typical colonies of staphylococci incubated for 24 hours at 35 ° C in Tryptic Soy Agar for the characterization tests (Gram stain, catalase, susceptibility to bacitracin and free coagulase). The identification of CoNS was performed through biochemical tests: susceptibility to novobiocin, growth under anaerobic conditions, presence of urease, the ornithine decarboxylation and acid production from the sugars mannose, maltose, trehalose, mannitol and xylose. The antimicrobial susceptibility examined by disk-diffusion technique. The technique of Polymerase Chain Reaction was used to confirm the presence of mecA gene and the ability to produce biofilm was verified by testing in vitro using polystyrene inert surface, in samples of resistant staphylococci. Among 440 ants, 85 (19.1%) were carrying coagulase-negative staphylococci (CoNS) of the species Staphylococcus saprophyticus (17), Staphylococcus epidermidis (15), Staphylococcus xylosus (13), Staphylococcus hominis hominis (10), Staphylococcus lugdunensis (10), Staphylococcus warneri (6), Staphylococcus cohnii urealyticum (5), Staphylococcus haemolyticus (3), Staphylococcus simulans (3), Staphylococcus cohnii cohnii (2), and Staphylococcus capitis (1). No Staphylococcus aureus was found. Among the isolates, 30.58% showed resistance to erythromycin. Two samples of CoNS (2.35%), obtained from the ant Tapinoma melanocephalum collected in the post-surgical female ward, S. Hominis hominis and S. lugdunensis harbored the mecA gene and were resistant to multiple antibiotics, and the specie S. hominis hominis even showed to be a biofilm producer. This study proves that ants act as carriers of multidrug-resistant coagulase-negative Staphylococci and biofilm producers and points to the risk of the spreading of pathogenic microorganisms by this insect in the hospital environment

Simulação em uso dos pisos de madeira de Eucalyptus sp e Corymbia maculata

A caracterização anatômica, física, mecânica e química da madeira fornece informações importantes para sua melhor utilização. Contudo, para que madeiras se tornem boa opção para o mercado de pisos, adicionalmente é necessária a realização de ensaios que simulem suas reais condições em serviço. Esses ensaios simulam o pisoteio executado pelos sapatos de salto com pequenas áreas de pressão, o arraste e a queda de objetos, a resistência à abrasão da superfície e o atrito oferecido durante o deslocamento de pessoas que caminham sobre ele. Grande dificuldade da seleção de novas madeiras para pisos está na ausência de valores de referência físico-mecânicos. O presente trabalho visou a caracterizar as madeiras de Eucalyptus clöeziana F. Muell, de Eucalyptus microcorys F. Muell e de Corymbia maculata Hook, para as propriedades de densidade básica, retratibilidade, aplicação de carga rolante, de atrito estático e dinâmico, endentação causada por cargas aplicadas em pequenas áreas, impacto da esfera de aço cadente e resistência à abrasão. Foi observado que as madeiras estudadas podem ser utilizadas para a confecção de pisos, de acordo com seus resultados obtidos e por meio de comparações com resultados de literatura.

Testes físico-mecânicos e físico-químicos do couro da tilápia vermelha

Realizaram-se testes físico-mecânicos e físico-químicos em couro de tilápia vermelha (Oreochromis spp.) a fim de testar a sua resistência. As amostras foram distribuídas em delineamento inteiramente ao acaso com dois tratamentos: no T1, procedeu-se à retirada do corpo-de-prova no sentido longitudinal e, no T2, à retirada do corpo-de-prova no sentido transversal. Para os testes de determinação da resistência à tração, alongamento e rasgamento progressivo, foi utilizado o dinamômetro EMIC, com velocidade de afastamento entre as cargas de 100 ± 20mm/min, em ambiente climatizado (± 23ºC e UR do ar de 50%), por 24 horas. A espessura do couro variou de 0,61 a 0,75mm, mas não houve diferença entre os sentidos analisados. O couro apresentou maior resistência à tração no sentido transversal, 25,89N/mm², (P<0,01), comparado ao sentido longitudinal, 14,20 N/mm². O alongamento foi significativamente (P<0,05) maior no sentido longitudinal, 80,8%, em relação ao transversal, 62,6%. Não houve diferença para o rasgamento progressivo entre os tratamentos. O couro apresentou teor de óxido de cromo de 3,8%, graxa de 15,1% e pH e cifra diferencial de 3,5 e 0,5, respectivamente. Os valores nos testes de resistência e físico-químicos apresentados pelo couro indicam que ele pode ser utilizado para a confecção de vestuário e artefatos de couro em geral.

Digestibilidade da Matéria Seca, Proteína Bruta e Energia Bruta da Silagem de Milho associada ao Concentrado, por meio de ensaios in vivo e in vitro

A study was made to compare dry matter, crude protein and gross energy digestibility of corn silage, associated to concentrate, through in vitro and in vivo digestion techniques. A completely randomized design was used, with two treatments and nine replications, involving three assays. The in vivo digestion assay was conducted with 12 Holstein heifers, on a 24 h permanent sample collection. The in vitro digestion assay was achieved with three collection methods: manual (M), vacuum pump (VP) and nasoesophagic (N). The collection methods VP and M can he used to determine the dry matter digestibility, instead of in vivo method, for the present study ration. The digestion methods influenced the DM, CP and GE digestibility for the studied ration.

Utilização da microscopia eletrônica de varredura como ferramenta de avaliação da estrutura do tecido de abacate 'quintal' após danos mecânicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aplicação de danos mecânicos em abacates e seus efeitos na qualidade dos frutos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da viabilidade da utilização de cinza de lodo de esgoto como adição em argamassa de cimento Portland

The use of sewage sludge as a raw material falls within the waste recycling key in the current process model environmental sustainability .Waste recycling has been consolidated as a sustainable environmentally sound technical solution, and. Despite showing very variable composition and characteristics, sewage sludge, can be considered as a residue with a high recycling potential in the building sector. In this paper the feasibility of using sewage sludge ash was studied in addition to Portland cement mortar in 1:3 mass considered the standard dash. This gray additions were studied in proportions of 5%, 10 %, 15 %, 20 %, 25% and 30% by mass of cement. The methodology was focused on the characterization of materials by physical, chemical , mechanical , environmental and morphological followed by the production of mortar tests ,and finalized by the characterization tests of mortar in the fresh state, through the consistency index, content of entrained air, bulk density and water retention, and in the hardened state by bulk density, water absorption by capillarity capillarity coefficient, compressive strength, tensile strength in bending ,tensile bond strength and microstructural analysis for percentages of 0 to 20%. After comparing with the standard mortar mortars with addition of ash, it is concluded that the ash of sewage sludge did not impair the integrity and properties of mortars with addition, including increasing resistance to compression and tension, being 20% more indicated percentage. Thus, it becomes feasible the addition of sewage sludge ash in Portland cement mortar for the trait studied

Avaliação de indicadores internos em ensaios de digestibilidade

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Resistência a compressão de tijolos de solo-cimento fabricados com o montículo do cupim Cornitermes cumulans (Kollar, 1832)

Objetivou-se neste trabalho, comparar a resistência à compressão de tijolos de solo-cimento fabricados com o montículo do cupim Cornitermes cumulans (Kollar, 1832), com tijolos que utilizaram como matéria prima um NEOSSOLO QUARTZARÊNICO (Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA), 1999), ambos submetidos a duas idades de cura (07 ou 28 dias). O experimento foi montado em delineamento inteiramente casualizado, em esquema fatorial 2x2, sendo analisados dois cofatores: a matéria prima base e a idade de cura. Os ensaios físicos e mecânicos obedeceram às prescrições das normas da Associação Brasileira de Normas Técnicas NBR-8492 (ABNT, 1982) e NBR-8491 (ABNT, 1984). Concluiu-se que a resistência à compressão dos tijolos foi maior com o aumento das idades de cura. O tratamento T4 apresentou maior valor de resistência à compressão, não diferindo estatisticamente dos tratamentos T2 e T1. Os tijolos fabricados com o montículo do cupim C. cumulans (Kollar, 1832) apresentaram diminuição da absorção de água com o aumento das idades de cura, o que normalmente corresponde a um maior aumento da resistência à compressão, ao contrário dos que utilizaram o NEOSSOLO QUARTZARÊNICO (Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA), 1999).

Viabilidade da Utilização de Máquinas de Indução Convencionais como Motores sem Mancais Mecânicos

Electrical Motors transform electrical energy into mechanic energy in a relatively easy way. In some specific applications, there is a need for electrical motors to function with noncontaminated fluids, in high speed systems, under inhospitable conditions, or yet, in local of difficult access and considerable depth. In these cases, the motors with mechanical bearings are not adequate as their wear give rise to maintenance. A possible solution for these problems stems from two different alternatives: motors with magnetic bearings, that increase the length of the machine (not convenient), and the bearingless motors that aggregate compactness. Induction motors have been used more and more in research, as they confer more robustness to bearingless motors compared to other types of machines building with others motors. The research that has already been carried out with bearingless induction motors utilized prototypes that had their structures of stator/rotor modified, that differ most of the times from the conventional induction motors. The goal of this work is to study the viability of the use of conventional induction Motors for the beringless motors applications, pointing out the types of Motors of this category that can be more useful. The study uses the Finite Elements Method (FEM). As a means of validation, a conventional induction motor with squirrel-cage rotor was successfully used for the beringless motor application of the divided winding type, confirming the proposed thesis. The controlling system was implemented in a Digital Signal Processor (DSP)