Effect of multiple firing and silica deposition on the zirconia-porcelain interfacial bond strength

Objectives. To test the hypothesis that multiple firing and silica deposition on the zirconia surface influence the bond strength to porcelain.Materials and methods. Specimens were cut from yttria-stabilized zirconia blocks and sintered. Half of the specimens (group S) were silica coated (physical vapor deposition (PVD)) via reactive magnetron sputtering before porcelain veneering. The remaining specimens (group N) had no treatment before veneering. The contact angle before and after silica deposition was measured. Porcelain was applied on all specimens and submitted to two (N2 and S2) or three firing cycles (N3 and S3). The resulting porcelain-zirconia blocks were sectioned to obtain bar-shaped specimens with 1 mm(2) of cross-sectional area. Specimens were attached to a universal testing machine and tested in tension until fracture. Fractured surfaces were examined using optical microscopy. Data were statistically analyzed using two-way ANOVA, Tukey's test (alpha = 0.05) and Weibull analysis.Results. Specimens submitted to three firing cycles (N3 and S3) showed higher mean bond strength values than specimens fired twice (N2 and S2). Mean contact angle was lower for specimens with silica layer, but it had no effect on bond strength. Most fractures initiated at porcelain-zirconia interface and propagated through the porcelain.Significance. The molecular deposition of silica on the zirconia surface had no influence on bond strength to porcelain, while the number of porcelain firing cycles significantly affected the bond strength of the ceramic system, partially accepting the study hypothesis. Yet, the Weibull modulus values of S groups were significantly greater than the m values of N groups. (C) 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Effect of 4 mass% Ag addition on the thermal behavior of the Cu-9 mass% Al alloy

The effect of 4 mass% Ag addition on the thermal behavior of the Cu-9 mass% Al alloy was studied using differential scanning calorimetry (DSC), optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and X-ray diffractometry (XRD). The results showed that the presence of silver causes (Cu)-alpha+(alpha+gamma1)-->(Cu)-alpha+beta transformation to occur in two stages. In the first one, part of the produced beta phase combines with the precipitated Ag to give a silver-rich phase and in the second one the transformation is completed. The formation of this silver-rich phase seems to be enhanced at very low cooling rates.

Evaluation of the effect of hyoscine-N-butyl bromide on the cardiovascular actions of detomidine in the horse

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

FACTORS THAT AFFECT THE ENZYMATIC DEGRADATION OF NATURAL STARCH GRANULES - EFFECT OF THE SIZE OF THE GRANULES

In this study the relationship between the enzymatic susceptibility and the size of the com and cassava starch granules was studied. The starch granules were separated by size and classified according to their average diameter in: a) larger than 16 mum; b) between 15 and 10 mum and c) smaller than 10 mum. The starch granules of various sizes were hydrolyzed by bacterial alpha-amylase and fungal amyloglucosidase. The results showed a relationship between the enzymatic susceptibility and the size of the starch granules; smaller size of the starch granules resulted in a higher percentage of hydrolysis. A basic difference in the mode of action of enzymes on small and large granules was observed. Enzymatic attack on the large granules was characterized by considerable surface corrosion, mainly at the radial axis. For small granules, the enzymatic action occurred on the surface of the granules and was characterized by an erosion with solubilization of the granules. Chemical and physical analysis of the starches suggested that hydrolysis should occur mainly at the amorphous areas of the granules.

Knoop hardness of dental resin cements: Effect of veneering material and light curing methods

This study evaluated the Knoop hardness of one resin cement (dual-cure mode or light-cure mode) when illuminated directly or through restorative materials-ceramic (HeraCeram) or composite (Artglass)-by two light curing units. Light curing was carried out using a conventional quartz tungsten halogen (QTH) light source (XL2500) for 40 s, and a light emitting diodes (LED) light source (Ultrablue Is) for 40 s. Bovine incisors had their buccal faces flattened and hybridised. on these surfaces, a mould was seated and filled with cement. A disc of the veneering material (1.5 mm thickness) was positioned over this set for light curing. After storage (24 h/37 degrees C), samples (n = 10) were sectioned for hardness (KHN) measurements. Data were submitted to ANOVA and to Tukey's test (alpha = 0.05). In general, light curing with LED resulted in higher hardness values than QTH. Distinct cement behaviour was observed with different veneering material in association with different light curing units (LCUs). (C) 2006 Elsevier Ltd. All rights reserved.

Idazoxan and the effect of intracerebroventricular oxytocin or vasopressin on sodium intake of sodium-depleted rats

The alpha(2)-adrenergic agonist clonidine and the neuropeptide oxytocin, inhibit sodium intake when injected intracerebroventricularly (i.c.v.). The present work investigates whether (1) vasopressin also inhibits sodium intake when injected i.c.v., and (2) the effect of oxytocin and of vasopressin on sodium intake is affected by i.c.v. injection of idazoxan, an alpha(2)-adrenergic antagonist. Clonidine (30 nmol), oxytocin (40, 80 nmol) and vasopressin (40, 80 nmol) were injected i.c.v. 20 min prior to a 1.5% NaCl appetite test, in rats depleted of sodium for 24 h by a combination of a single s.c. injection of furosemide (10 mg/rat) and removal of ambient sodium. Every dose of clonidine, oxytocin and vasopressin inhibited the 1.5% NaCl intake. Seizures were observed with the higher dose of vasopressin, but not with either dose of oxytocin. The effect of i.c.v. injection of clonidine (30 nmol), oxytocin (80 nmol) or vasopressin (40 nmol) was partially inhibited by prior i.c.v. injection of idazoxan (160, 320 nmol). The results suggest that the inhibition of 1.5% NaCl intake induced by i.c.v. injection of neuropeptides in sodium-depleted rats depends, in part, on the activation of central alpha(2)-adrenoceptors. (C) 1997 Elsevier B.V. B.V. All rights reserved.

Effect of long-term treatment with insulin and/or acarbose on glomerular basement membrane thickening in alloxan-diabetic rats

Acarbose is a competitive inhibitor of the intestinal alpha-glycosidases, that can delay absorption of intestinal carbohydrates causing their malabsorption. In the present paper we studied the effects of insulin, acarbose and their association on glomerular basement membrane thickening in alloxan-diabetic rats. Twenty-five male and female Wistar rats, approximately 3 months old at the beginning of the experiment, were assigned randomly to each of five experimental groups: normal control rats, alloxan-diabetic control rats, alloxan-diabetic rats treated with acarbose, alloxan-diabetic rats treated with insulin, and alloxan-diabetic rats treated with insulin plus acarbose. Alloxan was administered in a single iv dose of 42 mg/kg body weight. Insulin was given subcutaneously at doses of 18 to 30 IU/kg corrected daily on the basis of glycosuria and ketonuria. Acarbose was given mixed with rat chow in a dose of 50 mg/100 g chow. Body weight, water and food intake and diuresis, as well as blood and urine glucose were determined after 1, 3, 6, 9, and 12 months of treatment. Glomerular basement membrane (GBM) thickening was determined by electron microscopy at the same times. Clear clinical and laboratory signs of severe diabetes, with blood glucose levels above 200 mg/dl and urine glucose above 3000 mg/dl, were observed in all alloxan-diabetic control rats, in all periods of follow-up, whereas administration of insulin or acarbose reduced the blood glucose levels of treated groups. The most satisfactory control of blood and urine glucose was observed in animals treated with both insulin and acarbose. However, diarrhea was observed in diabetic rats treated with acarbose associated or not with insulin. GBM thickening was correlated with age in all groups. Beginning at six months after diabetes induction, the GBM of untreated diabetic rats was significantly thicker (mean +/- SEM, 4.446 +/- 0.45 mm) than that of normal rats (2.977 +/- 0.63 mm). Both insulin and acarbose prevented GBM thickening and their combination induced thickening similar to the age-dependent thickening observed for normal rats of the same age. We conclude that acarbose when combined with insulin may be a good option in the control of diabetes and its renal complications.

Effect of La2O3 doping on the microstructure and electrical properties of a SnO2-based varistor

The effect of La2O3 addition on the densification and electrical properties of the (0.9895 - x) SnO2 + 0.01 CoO + 0.0005 Nb2O5 + x La2O5 system, where x = 0.0005 or 0.00075, was considered in this study. The samples were sintered at 1300 degreesC for 2 and 4 h and a single SnO2 phase was identified by X-ray diffraction. Microstructure analysis by scanning electron microscopy showed that the affect of La2O3 addition is to decrease the SnO2 grain size. J versus E curves indicated that the system exhibits a varistor behavior and the effect of La2O3 is to increase both the non-linear coefficient (alpha) and the breakdown voltage (E-2). Considering the Schottky thermionic emission model the potential height and the width were estimated. The addition of small amounts of La2O3 to the basic system increases the potential barrier height and decreases both grain size and potential barrier width. (C) 2001 Kluwer Academic Publishers.

Effect of oxidizing and reducing atmospheres on the electrical properties of dense SnO2-based varistors

The SnO2 based varistor systems recently presented in the literature appear to have a promising potential in commercial applications. Experimental evidence shows that there is a dependence of nonlinear constant values with thermal treatment under different atmospheres. Thermal treatments in oxygen and nitrogen rich atmospheres at 900 degreesC prove this dependence, indicating that the nonlinear constant values are significantly lower when the material is submitted to a nitrogen atmosphere. Moreover, electrical properties can be restored when the varistor is subjected to thermal treatment at the same temperature in an oxygen atmosphere, indicating that the mechanism seems to be reversible. This paper discusses this behavior focusing in the grain boundary region. Ta2O5 mol% concentrations are also analyzed and the results indicate an optimum Ta2O5 concentration of 0.05 mol% for the electrical properties (alpha = 44 and E-B = 6150 V cm(-1)). (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Structural and spectroscopic analysis of gamma-Al2O3 to alpha-Al2O3-CoAl2O4 phase transition

Co-doped alumina powders were synthesized by means of the polymeric precursor method to obtain ceramic pigments. The effect of different contents of Co2+ on phase transition gamma to alpha-Al2O3 and appearing of CoAl2O4 spinel were studied by means of X-ray diffraction. A partial phase diagram of the system CoAl2O3 was proposed from these data by means of determination of the percentages of these phases according to the calcining temperature. Critical particle size to phase transition was determined by means of calculations of crystallite size and determination of superficial area through the BET method. UV-vis spectroscopy of the samples allow to compare the band shift with the phase transition. Besides, a study of thermal stability and intensity of the blue coloration of the synthesized powders with the presence of cobalt in relation to the calcining temperature was accomplished and compared to the phase transition. The results show that the higher blue color intensity was obtained for the powders with Co-doped gamma-Al2O3 closest of phase transition to alpha-Al2O3 + CoAl2O4. (c) 2005 Elsevier B.V. All rights reserved.

Structural organization of cetyltrimethylammonium sulfate in aqueous solution: the effect of Na2SO4

We used dynamic light scattering (DLS), a steady-state fluorescence, time resolved fluorescence quenching (TRFQ), tensiometry, conductimetry, and isothermal titration calorimetry (ITC) to investigate the self-assembly of the cationic surfactant cetyltrimethylammonium sulfate (CTAS) in aqueous solution, which has SO42- as divalent counterion. We obtained the critical micelled concentration (cmc), aggregation number (N-agg), area per monomer (a(0)), hydrodynamic radius (R-H), and degree of counterion dissociation (alpha) of CTAS micelles in the absence and presence of up to 1 M Na2SO4 and at temperatures of 25 and 40 degrees C. Between 0.01 and 0.3 M salt the hydrodynamic radius of CTAS micelle R-H approximate to 16 angstrom is roughly independent on Na2SO4 concentration; below and above this concentration range R-H increases steeply with the salt concentration, indicating micelle structure transition, from spherical to rod-like structures. R-H increases only slightly as temperature increases from 25 to 40 degrees C, and the cmc decreases initially very steeply with Na2SO4 concentration up to about 10 mM, and thereafter it is constant. The area per surfactant at the water/air interface, a(0), initially increases steeply with Na2SO4 concentration, and then decrases above ca. 10 mM. Conductimetry gives alpha = 0.18 for the degree of counterion dissociation, and N-agg obtained by fluorescence methods increases with surfactant concentration but it is roughly independent of up to 80 mM salt. The ITC data yield cmc of 0.22 mM in water, and the calculated enthalpy change of micelle formation, Delta H-mic = 3.8 kJ mol(-1), Gibbs free energy of micellization of surfactant molecules, Delta G(mic) = -38.0 kJ mol(-1) and entropy T Delta S-mic = 41.7 kJ mol(-1) indicate that the formation of CTAS micelles is entropy-driven. (c) 2006 Elsevier B.V. All rights reserved.

ANTINOCICEPTIVE EFFECT OF AMITRAZ IN MICE AND RATS

Amitraz, a formamidine insecticide and acaricide used in veterinary practice, presents side effects related to its pharmacological activity on az-adrenergic receptors. The present study was undertaken to investigate the antinociceptive effect of amitraz in rats and mice. The tail-flick test was used to determine the duration of the antinociceptive effect of the intraperitoneal tip) administration of amitraz (1 and 2 mg/kg, 10 animals per group) in male Wistar rats weighing 180-220 g. The writhing test (using 10 ml/kg of a 0.6% acetic acid solution as a painful stimulus). was performed in 140 male Swiss mice weighing 20-30 g, divided into 14 groups that received ip injections of saline, amitraz (0.5, 1.0, 1.5, 2.0 and 4.0 mg/kg), xylazine or detomidine (1.0, 1.5, 2.0 and 4.0 mg/ kg), in order to compare the effect of amitraz to that caused by xylazine and detomidine, and to investigate the participation of alpha(2)-adrenergic receptors which were blocked by idazoxan (1 mg/kg). Amitraz induced a significant antinociceptive effect in both rats and mice. This effect is blocked in mice by idazoxan.

The effect of polymerization cycles on porosity of microwave-processed denture base resin

Statement of problem. Although most of the physical properties of denture base resin polymerized by microwave energy have been shown to be similar to resins polymerized by the conventional heat polymerization method, the presence of porosity is a problem.Purpose. This study evaluated the effect of different microwave polymerization cycles on the porosity of a denture base resin designed for microwave polymerization.Material and methods. Thirty-two rectangular resin specimens (65 X 40 X 5 mm) were divided into 3 experimental groups (A, B, and C; Onda-Cryl, microwave-polymerized resin) and I control group (T; Classico, heat-polymerized resin), according to the following polymerization cycles: (A) 500 W for 3 minutes, (B) 90 W for 13 minutes + 500 W for 90 seconds, (C) 320 W for 3 minutes + 0 W for 4 minutes + 720 W for 3 minutes, and (T) 74degreesC for 9 hours. Porosity was calculated by measurement of the specimen volume before and after its immersion in water. Data were analyzed using 1-way analysis of variance (alpha = .05).Results. The mean values and SDs of the percent mean porosity were: A = 1.05% +/- 0.28%, B = 0.91% +/- 0.15%, C = 0.88% +/- 0.23%, T = 0.93% +/- 0.23%. No significant differences were found in mean porosity among the groups evaluated.Conclusion. Within the limitations of this study, a denture base resin specifically designed for microwave Polymerization tested was not affected by different polymerization cycles. Porosity was similar to the conventional heat-polymerized denture base resin tested.

Effect of low contents of a polyaniline derivative on the crystallization and electrical properties of blends with PVDF

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The investigation of alpha -> beta phase transition in poly(vinylidene fluoride) (PVDF)

The phase transition from the non-polar a-phase to the polar beta-phase of poly(vinylidene fluoride) (PVDF) has been investigated using micro-Raman spectroscopy, which is advantageous for being a non-destructive technique. Films of alpha-PVDF were subjected to stretching under controlled rates and at 80 degrees C, the transition to beta-PVDF being monitored by the decrease in the Raman band at 794 cm(-1) characteristic of the a-phase, with the concomitant increase in the 839 cm(-1) band characteristic of the beta-phase. Poling with negative corona discharge was found to affect the alpha-PVDF morphology improving the Raman bands related to this crystalline phase. This effect is minimized for films stretched to higher ratios. Significantly, corona-induced effects could not be observed with the other experimental techniques, viz. X-ray diffraction and infrared spectroscopy.