876 resultados para Load voltage maximization
Resumo:
In Russian there are more than twenty thousand primary substations 35/110 kV and 10/110 kV. According to the Government Plan of Power Industry Development until 2020 year more than hundred new substations will e installed every year and even more renewed. The goal of this Thesis is to find out in this business environment what are the technology opportunities of prefabricated substation modules in new substation or in modernization of old substations in Russia.
Resumo:
The pulsed dielectric barrier discharge (PDBD) and pulsed corona discharge (PCD) were compared for their efficiency to degrade phenol in water solution. Results show that PCD has higher efficiency than PDBD to degrade phenol. When initial pH of water solution was elevated, phenol degradation in the PCD reactor was significantly enhanced, although no considerable effect was seen in the PDBD reactor. The PCD reactor was also able to degrade lignin significantly, both in synthetically prepared solution and in pulp and paper mill wastewater. Water temperature did not affect phenol degradation; however, lignin was better oxidized at lower temperature.
Resumo:
Under pathological conditions, microglia, the resident CNS immune cells, become reactive and release pro-inflammatory cytokines and neurotoxic factors. We investigated whether this phenotypic switch includes changes in the expression of the L-type voltage-gated calcium channel (VGCC) in a rat model of N-methyl-d-aspartate-induced hippocampal neurodegeneration. Double immunohistochemistry and confocal microscopy evidenced that activated microglia express the L-type VGCC. We then analyzed whether BV2 microglia express functional L-type VGCC, and investigated the latter's role in microglial cytokine release and phagocytic capacity. Activated BV2 microglia express the CaV1.2 and CaV1.3 subunits of the L-type VGCC determined by reverse transcription-polymerase chain reaction, Western blot and immunocytochemistry. Depolarization with KCl induced a Ca2+ entry facilitated by Bay k8644 and partially blocked with nifedipine, which also reduced TNF-α and NO release by 40%. However, no nifedipine effect on BV2 microglia viability or phagocytic capacity was observed. Our results suggest that in CNS inflammatory processes, the L-type VGCC plays a specific role in the control of microglial secretory activity.
Resumo:
Tässä työssä tarkastellaan taajuusmuuttajan vanhenemista syklisissä käytöissä puolijohdetehokomponenttien osalta. Laitteiden vikaantumisprosessien analysoimiseksi työssä suunnitellaan syklinen kestotestausjärjestelmä, joka mahdollistaa useamman taajuusmuuttajan yhtäaikaisen vanhentamisen. Jaksottaisesti toistuvat kuormitussyklit rasittavat termomekaanisesti taajuusmuuttajan tehomoduulin sisäisiä rakenteita suurten lämpötilavaihtelujen johdosta. Teoriaosuuden pääpaino kohdistuu puolijohdetehokomponenttien rakenteeseen, vikaantumisprosesseihin ja eliniän kartoittamiseen. Työssä käydään läpi yleisimpien pienijännitteisten moottorinohjausinverttereiden tehomoduulien mekaaniset rakenteet, tyypillisemmät syklisestä kuormituksesta johtuvat vikaantumisprosessit sekä puolijohdetehokomponenttivalmistajien käyttämät syklisen eliniän testausmenetelmät. Loppuosassa työtä suunnitellaan taajuusmuuttajan syklinen kestotestausjärjestelmä laitteiden keinotekoista vanhentamista varten. Testausjärjestelmällä voidaan kuormittaa useampaa taajuusmuuttajaa vuorottain mielivaltaisella kuormitusvirtaprofiililla. Laitteita vanhennettiin kaksi testierää kuormittamalla niitä jaksottaisesti hissikäytön tyypillisellä kuormitusprofiililla. Puolijohdetehokomponentin vanhenemisen edistystä seurattiin termisen impedanssiketjun mittausmenetelmällä, joka perustuu IGBT:n kollektoriemitterijännitteen lämpötilariippuvuuteen. Testilaitteiden puolijohdetehokomponentit hajosivat syklisen eliniän päättymiseen teoriassa esitettyjen vikaantumisprosessien seurauksesta. Tehomoduulien vika-analyysi osoittaa syklisen kestotestausjärjestelmän soveltuvaksi menetelmäksi tutkia erilaisten kuormitusprofiilien vaikutusta taajuusmuuttajan vanhenemiseen.
Resumo:
Distribution companies are facing numerous challenges in the near future. Regulation defines correlation between power quality and revenue cap. Companies have to take measures for reliability increase to successfully compete in modern conditions. Most of the failures seen by customers originate in medium voltage networks. Implementation of network automation is the very effective measure to reduce duration and number of outages, and consequently, outage costs. Topic of this diploma work is study of automation investments effect on outage costs and other reliability indices. Calculation model have been made to perform needed reliability calculations. Theoretical study of different automation scenarios has been done. Case feeder from actual distribution company has been studied and various renovation plans have been suggested. Network automation proved to be effective measure for increasing medium voltage network reliability.
Resumo:
In liberalized electricity markets, which have taken place in many countries over the world, the electricity distribution companies operate in the competitive conditions. Therefore, accurate information about the customers’ energy consumption plays an essential role for the budget keeping of the distribution company and for correct planning and operation of the distribution network. This master’s thesis is focused on the description of the possible benefits for the electric utilities and residential customers from the automatic meter reading system usage. Major benefits of the AMR, illustrated in the thesis, are distribution network management, power quality monitoring, load modelling, and detection of the illegal usage of the electricity. By the example of the power system state estimation, it was illustrated that even the partial installation of the AMR in the customer side leads to more accurate data about the voltage and power levels in the whole network. The thesis also contains the description of the present situation of the AMR integration in Russia.
Resumo:
Yhteiskunnan riippuvuus sähköstä on lisääntynyt voimakkaasti viime vuosikymmenien aikana. Sähkönjakelussa esiintyneet lyhyet ja pitkät keskeytykset ovat osoittaneet yhteiskunnan haavoittuvuuden ja yhteiskunta kestää entistä vähemmän sähkönjakelussa tapahtuvia häiriöitä. Keskeytyksistä aiheutuneiden haittojen arvostus on kasvanut ja tämä on luonut taloudelliset perusteet sähkön laatua parantaville investoinneille. Haja-asutusalueiden keskijänniteverkon johdot on rakennettu avojohtoina ja siten ne ovat alttiita sääolosuhteista johtuville myrsky- ja lumikuormavaurioille. Ilmastomuutoksen ennustetaan lisäävän tuulisuutta ja siten ongelmat sähkönjakelussa mahdollisesti lisääntyvät. Taajamissa käytetään enemmän kaapeleita ja johtolähdöt ovat lyhyitä, joten myrskyistä aiheutuvia keskeytyksiä on vähemmän kuin haja-asutusalueella. Olemassa olevat jakeluverkot ovat käytössä vielä vuosikymmeniä, joten uuden tekniikan kehittämisen rinnalla on kehitettävä myös olemassa olevaa jakeluverkkoa ja sen ylläpitoa. Ylläpidon tavoitteena on käyttövarmuuden parantamisen lisäksi huolehtia siitä, että jakeluverkkoihin sitoutunut omaisuus säilyttää arvonsa mahdollisimman hyvin pitoajan loppuun saakka. Jakeluverkkoihin investoitiin paljon 1950–70-luvuilla. Tältä ajalta on yhä käytössä puupylväitä, joiden ikääntymisen takia korvausinvestointien tarve kasvaa. Hyvänä puolena tässä on että käyttövarmuuden parantamiseksi olemassa olevaa jakeluverkkoa ei tarvitse uusia ennenaikaisesti. Tutkimuksessa päähuomio on haja-asutusalueiden 20 kV keskijänniteverkon kehittämisessä, sillä yli 90 % asiakkaiden kokemista keskeytyksistä johtuu keskijänniteverkon vioista. Erityisesti johtorakenteisiin ja johtojen sijoittamiseen on kiinnitettävä huomiota. Käyttövarmuuden lisäksi jakeluverkkojen kehittämistä ohjaavia tekijöitä ovat taloudellisuus, ympäristön huomioiminen, viranomaisvalvonta sekä asiakkaiden ja omistajien odotukset. Haja-asutusalueilla taloudelliset haasteet ovat suuret vakituisen väestön vähenemisen ja mahdollisesti sähköntarpeen pienenemisen takia. Taloudellisuus korostuu ja riskit kasvavat, kun tuottojen määrä supistuu tarvittaviin jakeluverkon investointeihin ja ylläpitokustannuksiin verrattuna. Ristiriitaa aiheuttaa se, että asiakkaat odottavat sähkönjakelulta parempaa luotettavuutta, mutta paremmasta sähkönlaadusta ei olla valmiita maksamaan juurikaan nykyistä enempää. Jakeluverkkojen kehittämistä voi hidastaa myös viranomaisvalvonta, jos tuottoja ei voida lisätä investointien lisätarpeiden suhteessa. Tutkimuksessa on analysoitu yleisellä tasolla kaapeloinnin lisäämistä, korkeiden pylväiden käyttämistä, leveitä johtokatuja, edullisten ja yksinkertaisten sähköasemien rakentamista haja-asutusalueille ja automaatioasemien lisäämistä keskijänniteverkon solmupisteisiin. Erityisesti tutkimuksessa on analysoitu uutena tekniikkana 1000 V jännitteen käyttömahdollisuutta jakeluverkkojen kehittämisessä. Sähköjohtojen siirtäminen teiden varsiin parantaa käyttövarmuutta, vaikka johdot rakennetaan samalla tekniikalla kuin olemassa olevat johdot. Hajaasutusalueille rakennettavilla sähköasemilla pitkät syöttöjohdot voidaan jakaa pienemmiksi syöttöalueiksi, jolloin keskeytyksistä aiheutuvat haitat koskettavat kerrallaan pienempää asiakasmäärää. Samaan tulokseen päästään oikein sijoitetuilla ja toteutetuilla automaatioasemilla. Tutkimuksen mukaan lupaavaksi tekniikaksi jakeluverkkojen kehittämisessä on osoittautumassa 1000 V jänniteportaan ottaminen 400 V pienjännitteen lisäksi. 1000 V verkoilla voidaan korvata häiriöherkkiä 20 kV keskijänniteverkon lyhyitä, alle viiden kilometrin pituisia haarajohtoja ja haarajohtojen jatkeita, missä siirrettävät tehot ovat pieniä. Uudessa jakelujärjestelmässä sähkö tuodaan 1000 V jännitteellä lähelle asiakasta, jossa jännite muunnetaan normaaliksi asiakkaille soveltuvaksi 400/230 V jännitteeksi. Edullisuus perustuu siihen, että rakentamisessa käytetään samoja pienjännitejohtoja kuin asiakkaille menevässä 400 V pienjänniteverkossa. 1000 V jakelutekniikassa sekä investointikustannukset että ylläpitokustannukset ovat pienemmät kuin perinteisessä 20 kV ilmajohtotekniikassa. 1000 V johdot säästävät maisemaa, sillä ne eivät tarvitse leveää johtokatua kuten 20 kV keskijännitejohdot. 1000 V verkkojen käyttö soveltuukin erityisesti vapaa-ajanasuntojen sähköistykseen herkissä ranta- ja järvimaisemissa. 1000 V verkot mahdollistavat kaapeliauraamisen lisäämisen ja näin voidaan vähentää ympäristöä haittaavien kyllästettyjen pylväiden käyttöä. 1000 V jakeluverkkojen osalta tutkimustyön tuloksia on sovellettu suomalaisessa Suur-Savon Sähkö Oy:ssä. Käytännön kokemuksia 1000 V jakelujärjestelmästä on useista kymmenistä kohteista. Tutkimustulokset osoittavat, ettei keskijänniteverkon maakaapelointi hajaasutusalueilla ole taloudellisesti kannattavaa nykyisillä keskeytyksistä aiheutuvilla haitta-arvoilla, mutta jos keskeytyskustannusten arvostus kasvaa, tulee kaapelointi kannattavaksi monissa paikoissa. Myös myrskyisyyden ja myrskyistä aiheutuvien jakelukeskeytysten lisääntyminen tekisi kaapeloinnista kannattavan. Tulevaisuudessa jakeluverkkojen rakentaminen on entistä monimuotoisempi tehtävä, jossa taloudellisuuden ja käyttövarmuuden lisäksi on huomioitava asiakkaat, omistajat, viranomaiset ja ympäristö. Tutkimusta jakelutekniikan kehittämiseksi tarvitaan edelleen. Tulevaisuuden osalta haja-asutusalueiden jakeluverkkojen kehittämiseen liittyy paljon epävarmuuksia. Hajautetun kiinteistökohtaisen sähköntuotannon lisääntyminen voi tehdä jakeluverkoista nykyistä tarpeettomampia, mutta esimerkiksi liikenteen sähköistyminen voi kasvattaa jakeluverkkojen merkitystä. Tästä syystä jakeluverkkojen rakentamisessa tarvitaan joustavuutta, jotta tarvittaessa voidaan helposti sopeutua erilaisiin kehityssuuntiin.
Resumo:
Power transformer is the most expensive equipment on a substation. It is always necessary to get needed benefit with the lowest expenses. Producing of power transformers with reduced insulation strength is one of the possible ways to reduce expenses. Exploitation of such transformers was begun in the end of 70-th in the last century. Protection from overvoltages was done with valve-type magnetic combined surge arresters with increased blanking voltage during switching overvoltages. Nowadays there is the necessity of replacement of those devices. That’s why modernized nonlinear surge arrester was invented. This master’s thesis is focused on the use research of that modernized device in comparison with usual nonlinear surge arresters. The goal is to show the lightning overvoltages level using different types of nonlinear surge arresters and then calculations of the lightning protection reliability.
Resumo:
Since it is virtually impossible to balance loads in three-phase system, unbalance in a varying degree exists almost in all distribution networks. The aim of the thesis is to analyze the impact of this unbalance subject to different configurations of distribution system and winding connection of the supplying transformer. Also impact of the voltage unbalance on the equipment is investigated. In order to make the investigation more visual, the following calculations have been conducted: - Unsymmetrical load in four-wire star connected network - Unsymmetrical load in four-wire star connected network with broken zero conductor (or three-wire network). - Unsymmetrical load when the supplying transformer is so-called zigzag transformer. PDF created
Resumo:
Technical analysis of Low Voltage Direct Current (LVDC) distribution systems shows that in LVDC transmission the customer voltage quality is higher. One of the problems in LVDC distribution networks that converters both ends of the DC line are required. Because of the converters produce not pure DC voltage, but some fluctuations as well, the huge electrolytic capacitors are required to reduce voltage distortions in the DC-side. This thesis master’s thesis is focused on calculating required DC-link capacitance for LVDC transmission and estimation of the influence of different parameters on the voltage quality. The goal is to investigate the methods of the DC-link capacitance estimation and location in the transmission line.
Resumo:
Electron transport in a self-consistent potential along a ballistic two-terminal conductor has been investigated. We have derived general formulas which describe the nonlinear current-voltage characteristics, differential conductance, and low-frequency current and voltage noise assuming an arbitrary distribution function and correlation properties of injected electrons. The analytical results have been obtained for a wide range of biases: from equilibrium to high values beyond the linear-response regime. The particular case of a three-dimensional Fermi-Dirac injection has been analyzed. We show that the Coulomb correlations are manifested in the negative excess voltage noise, i.e., the voltage fluctuations under high-field transport conditions can be less than in equilibrium.
Resumo:
A mathematical model of the voltage drop which arises in on-chip power distribution networks is used to compare the maximum voltage drop in the case of different geometric arrangements of the pads supplying power to the chip. These include the square or Manhattan power pad arrangement, which currently predominates, as well as equilateral triangular and hexagonal arrangements. In agreement with the findings in the literature and with physical and SPICE models, the equilateral triangular power pad arrangement is found to minimize the maximum voltage drop. This headline finding is a consequence of relatively simple formulas for the voltage drop, with explicit error bounds, which are established using complex analysis techniques, and elliptic functions in particular.
Resumo:
Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.
Resumo:
Tämän työn tavoitteena on analysoida Vaasan Sähköverkko Oy:n keskijänniteverkon nykytila sekä selvittää verkon kehittämisen suuntaviivoja. Nykytilan määrityksessä selvitetään kuormitettavuusasteet, jännitteenalenemat, häviöt oiko- ja maasulkusuojauksen toimivuus sekä keskeytyskustannukset. Nykytilan määrityksen apuna käytettiin verkkotietojärjestelmä Xpowerin tehojako-, oikosulku- ja maasulkulaskentoja. Nykytila on määritetty sekä normaalissa kytkentätilanteessa, että tilanteessa jossa yksi sähköasema kerrallaan on poissa käytöstä. Nykytilan määrityksen perusteella voidaan todeta, että normaalissa kytkentätilanteessa keskijänniteverkko täyttää suurilta osin sille asetetut tekniset reunaehdot, jotka ovat jännitteenalenema, kuormitettavuus, oikosulkukestoisuus sekä oiko- ja maasulkusuojauksen havahtuvaisuus. Jotta reunaehdot toteutuisivat kokonaisuudessaan, tulee oikosulkukestottomien lähtöjen releasetteluja muuttaa tai vaihtaa oikosulkukestottomat johto-osuudet suurempi poikkipintaiseen johtimeen. Nykytilan määrityksen perusteella neljän päämuuntajan kuormitettavuusaste on yli 90 %, joten näiden asemien alueiden kehitystä tulee tarkkailla. Sähköasemien korvaustarkastelun perusteella viiden sähköaseman korvaus tuottaa ongelmia jo nykyisillä huippukuormilla. Työssä tehtyjen selvitystöiden perusteella Vaasan Sähköverkko Oy:n keskijänniteverkkoon lisättiin 10 maastokatkaisijaa sekä selvitettiin verkon mahdollisia tulevaisuuden kehittämisen suuntaviivoja.
Resumo:
To predict the capacity of the structure or the point which is followed by instability, calculation of the critical crack size is important. Structures usually contain several cracks but not necessarily all of these cracks lead to failure or reach the critical size. So, defining the harmful cracks or the crack size which is the most leading one to failure provides criteria for structure’s capacity at elevated temperature. The scope of this thesis was to calculate fracture parameters like stress intensity factor, the J integral and plastic and ultimate capacity of the structure to estimate critical crack size for this specific structure. Several three dimensional (3D) simulations using finite element method by Ansys program and boundary element method by Frank 3D program were carried out to calculate fracture parameters and results with the aid of laboratory tests (loaddisplacement curve, the J resistance curve and yield or ultimate stress) leaded to extract critical size of the crack. Two types of the fracture which is usually affected by temperature, Elastic and Elasti-Plastic fractures were simulated by performing several linear elastic and nonlinear elastic analyses. Geometry details of the weldment; flank angle and toe radius were also studied independently to estimate the location of crack initiation and simulate stress field in early stages of crack extension in structure. In this work also overview of the structure’s capacity in room temperature (20 ºC) was studied. Comparison of the results in different temperature (20 ºC and -40 ºC) provides a threshold of the structure’s behavior within the defined range.