Nonlinear Finite Element Study of Piles in Integral Abutment Bridges, HR-227, Part 2, 1982

The highway departments of the states which use integral abutments in bridge design were contacted in order to study the extent of integral abutment use in skewed bridges and to survey the different guidelines used for analysis and design of integral abutments in skewed bridges. The variation in design assumptions and pile orientations among the various states in their approach to the use of integral abutments on skewed bridges is discussed. The problems associated with the treatment of the approach slab, backfill, and pile cap, and the reason for using different pile orientations are summarized in the report. An algorithm based on a state-of-the-art nonlinear finite element procedure previously developed by the authors was modified and used to study the influence of different factors on behavior of piles in integral abutment bridges. An idealized integral abutment was introduced by assuming that the pile is rigidly cast into the pile cap and that the approach slab offers no resistance to lateral thermal expansion. Passive soil and shear resistance of the cap are neglected in design. A 40-foot H pile (HP 10 X 42) in six typical Iowa soils was analyzed for fully restrained pile head and pinned pile head. According to numerical results, the maximum safe length for fully restrained pile head is one-half the maximum safe length for pinned pile head. If the pile head is partially restrained, the maximum safe length will lie between the two limits. The numerical results from an investigation of the effect of predrilled oversized holes indicate that if the length of the predrilled oversized hole is at least 4 feet below the ground, the vertical load-carrying capacity of the H pile is only reduced by 10 percent for 4 inches of lateral displacement in very stiff clay. With no predrilled oversized hole, the pile failed before the 4-inch lateral displacement was reached. Thus, the maximum safe lengths for integral abutment bridges may be increased by predrilling. Four different typical Iowa layered soils were selected and used in this investigation. In certain situations, compacted soil (> 50 blow count in standard penetration tests) is used as fill on top of natural soil. The numerical results showed that the critical conditions will depend on the length of the compacted soil. If the length of the compacted soil exceeds 4 feet, the failure mechanism for the pile is similar to one in a layer of very stiff clay. That is, the vertical load-carrying capacity of the H pile will be greatly reduced as the specified lateral displacement increases.

Martensitic phase transformation in rapidly solidified Mn50Ni40In10 alloy ribbons

Heusler alloy Mn50Ni40In10 was produced as preferentially textured ribbon flakes by melt spinning, finding the existence of martensitic-austenic transformation with both phases exhibiting ferromagnetic ordering. A microcrystalline three-layered microstructure of ordered columnar grains grown perpendicularly to ribbon plane was formed between two thin layers of smaller grains. The characteristic temperatures of the martensitic transformation were MS=213 K, Mf=173 K, AS=222 K, and Af=243 K. Austenite phase shows a cubic L21 structure (a=0.6013(3) nm at 298 K and a Curie point of 311 K), transforming into a modulated fourteen-layer modulation monoclinic martensite

Novel cell types, neurosecretory cells, and body plan of the early-diverging metazoan Trichoplax adhaerens.

BACKGROUND: Trichoplax adhaerens is the best-known member of the phylum Placozoa, one of the earliest-diverging metazoan phyla. It is a small disk-shaped animal that glides on surfaces in warm oceans to feed on algae. Prior anatomical studies of Trichoplax revealed that it has a simple three-layered organization with four somatic cell types. RESULTS: We reinvestigate the cellular organization of Trichoplax using advanced freezing and microscopy techniques to identify localize and count cells. Six somatic cell types are deployed in stereotyped positions. A thick ventral plate, comprising the majority of the cells, includes ciliated epithelial cells, newly identified lipophil cells packed with large lipid granules, and gland cells. Lipophils project deep into the interior, where they alternate with regularly spaced fiber cells whose branches contact all other cell types, including cells of the dorsal and ventral epithelium. Crystal cells, each containing a birefringent crystal, are arrayed around the rim. Gland cells express several proteins typical of neurosecretory cells, and a subset of them, around the rim, also expresses an FMRFamide-like neuropeptide. CONCLUSIONS: Structural analysis of Trichoplax with significantly improved techniques provides an advance in understanding its cell types and their distributions. We find two previously undetected cell types, lipohil and crystal cells, and an organized body plan in which different cell types are arranged in distinct patterns. The composition of gland cells suggests that they are neurosecretory cells and could control locomotor and feeding behavior.

Fibrinmatrix erhöht Adhärenz von regenerativen peripheren Nervenzellen [Fibrin matrix enhances adherence of peripheral nerve regenerative cells]

Optimal seeding of a nerve conduit with cells is a core problem in tissue engineering of constructing an artificial nerve substitute to gap lesions in the peripheral nerve system. An ideal nerve gap substitute would have to present an equally distributed number of cells that can activate the regrowing axons. This work shows a new in vitro technique of two-step seeding of cells inside a conduit and on layered mats that allows a valuable targeting of the cells and a proven survival in the environment of poly-3-hydroxybutyrate (PHB) conduits. The technique uses two components of diluted fibrin glue Tisseel. Initially, the chosen area on the mat was coated with thrombin followed from the seeding of a fibrinogen-cell compound. Using Sprague Dawley rat cells, we could demonstrate with immunohistochemistry (S100, DAPI) techniques that undifferentiated (uMSC) and Schwann cells (SC) mimicking differentiated mesenchymal stem cells (dMSC) as well as SC can be suspended and targeted significantly better in dissolvable diluted fibrin glue than in growth medium. Analysis showed significantly better values for adherence (p < 0.001) and drop off (p < 0.05) from seeded cells. Using this two-step application allows the seeding of the cells to be more precise and simplifies the handling of cell transplantation.

Mutations in tubulin genes are frequent causes of various foetal malformations of cortical development including microlissencephaly.

Complex cortical malformations associated with mutations in tubulin genes are commonly referred to as "Tubulinopathies". To further characterize the mutation frequency and phenotypes associated with tubulin mutations, we studied a cohort of 60 foetal cases. Twenty-six tubulin mutations were identified, of which TUBA1A mutations were the most prevalent (19 cases), followed by TUBB2B (6 cases) and TUBB3 (one case). Three subtypes clearly emerged. The most frequent (n = 13) was microlissencephaly with corpus callosum agenesis, severely hypoplastic brainstem and cerebellum. The cortical plate was either absent (6/13), with a 2-3 layered pattern (5/13) or less frequently thickened (2/13), often associated with neuroglial overmigration (4/13). All cases had voluminous germinal zones and ganglionic eminences. The second subtype was lissencephaly (n = 7), either classical (4/7) or associated with cerebellar hypoplasia (3/7) with corpus callosum agenesis (6/7). All foetuses with lissencephaly and cerebellar hypoplasia carried distinct TUBA1A mutations, while those with classical lissencephaly harbored recurrent mutations in TUBA1A (3 cases) or TUBB2B (1 case). The third group was polymicrogyria-like cortical dysplasia (n = 6), consisting of asymmetric multifocal or generalized polymicrogyria with inconstant corpus callosum agenesis (4/6) and hypoplastic brainstem and cerebellum (3/6). Polymicrogyria was either unlayered or 4-layered with neuronal heterotopias (5/6) and occasional focal neuroglial overmigration (2/6). Three had TUBA1A mutations and 3 TUBB2B mutations. Foetal TUBA1A tubulinopathies most often consist in microlissencephaly or classical lissencephaly with corpus callosum agenesis, but polymicrogyria may also occur. Conversely, TUBB2B mutations are responsible for either polymicrogyria (4/6) or microlissencephaly (2/6).

Industrial nanoparticle application : representative survey among Swiss companies shows low usage and basic protection means

Manufactured nanoparticles are introduced into industrial processes, but they are suspected to cause similar negative health effects as ambient particles. The poor knowledge about the scale of this introduction did not allow global risk analysis so far. In 2006 a targeted telephone survey among Swiss companies (1) showed the usage of nanoparticles in a few selected companies but did not provide data to extrapolate on the totality of the Swiss workforce. To gain this kind of information a layered representative questionnaire survey among 1'626 Swiss companies was conducted in 2007. Data was collected about the number of potentially exposed persons in the companies and their protection strategy. The response rate was 58.3%. An expected number of 586 companies (95%−confidence interval 145 to 1'027) was shown by this study to use nanoparticles in Switzerland. Estimated 1'309 (1'073 to 1'545) workers do their job in the same room as a nanoparticle application. Personal protection was shown to be the predominant type of protection means. Companies starting productions with nanomaterials need to consider incorporating protection measures into the plans. This will not only benefit the workers' health, but will also likely increase the competitiveness of the companies. Technical and organisational protection means are not only more cost−effective on the long term, but are also easier to control. Guidelines may have to be designed specifically for different industrial applications, including fields outside nanotechnology, and adapted to all sizes of companies.

Trace element distribution among rock-forming minerals from metamorphosed to partially molten basic igneous rocks in a contact aureole (Fuerteventura, Canaries)

Low pressure partial melting of basanitic and ankaramitic dykes gave rise to unusual, zebra-like migmatites, in the contact aureole of a layered pyroxenite-gabbro intrusion, in the root zone of an ocean island (Basal Complex, Fuerteventura, Canary Islands). These migmatites are characterised by a dense network of closely spaced, millimetre-wide leucocratic segregations. Their mineralogy consists of plagioclase (An(32-36)), diopside, biotite, oxides (magnetite, ilmenite), +/-amphibole, dominated by plagioclase in the leucosome and diopside in the melanosome. The melanosome is almost completely recrystallised, with the preservation of large, relict igneous diopside phenocrysts in dyke centres. Comparison of whole-rock and mineral major- and trace-element data allowed us to assess the redistribution of elements between different mineral phases and generations during contact metamorphism and partial melting. Dykes within and outside the thermal aureole behaved like closed chemical systems. Nevertheless, Zr, Hf, Y and REEs were internally redistributed, as deduced by comparing the trace element contents of the various diopside generations. Neocrystallised diopside - in the melanosome, leucosome and as epitaxial phenocryst rims - from the migmatite zone, are all enriched in Zr, Hf, Y and REEs compared to relict phenocrysts. This has been assigned to the liberation of trace elements on the breakdown of enriched primary minerals, kaersutite and sphene, on entering the thermal aureole. Major and trace element compositions of minerals in migmatite melanosomes and leucosomes are almost identical, pointing to a syn- or post-solidus reequilibration on the cooling of the migmatite terrain i.e. mineral-melt equilibria were reset to mineral-mineral equilibria. (C) 2007 Elsevier B.V. All rights reserved.

Bayesian Markov-chain-Monte-Carlo inversion of time-lapse cross hole ground-penetrating radar data to characterize the vadose zone at the Arrenaes field site, Denmark

The ground-penetrating radar (GPR) geophysical method has the potential to provide valuable information on the hydraulic properties of the vadose zone because of its strong sensitivity to soil water content. In particular, recent evidence has suggested that the stochastic inversion of crosshole GPR traveltime data can allow for a significant reduction in uncertainty regarding subsurface van Genuchten-Mualem (VGM) parameters. Much of the previous work on the stochastic estimation of VGM parameters from crosshole GPR data has considered the case of steady-state infiltration conditions, which represent only a small fraction of practically relevant scenarios. We explored in detail the dynamic infiltration case, specifically examining to what extent time-lapse crosshole GPR traveltimes, measured during a forced infiltration experiment at the Arreneas field site in Denmark, could help to quantify VGM parameters and their uncertainties in a layered medium, as well as the corresponding soil hydraulic properties. We used a Bayesian Markov-chain-Monte-Carlo inversion approach. We first explored the advantages and limitations of this approach with regard to a realistic synthetic example before applying it to field measurements. In our analysis, we also considered different degrees of prior information. Our findings indicate that the stochastic inversion of the time-lapse GPR data does indeed allow for a substantial refinement in the inferred posterior VGM parameter distributions compared with the corresponding priors, which in turn significantly improves knowledge of soil hydraulic properties. Overall, the results obtained clearly demonstrate the value of the information contained in time-lapse GPR data for characterizing vadose zone dynamics.

The Dutung-Thaktote extensional fault zone and nappe structures documented by illite crystallinity and clay-mineral paragenesis in the Tethys Himalaya between Spiti river and Tso Morari, NW India

Numerous measurements by XRD of the Scherrer width at half-peak height (001 reflection of illite), coupled with analyses of clay-size assemblages, provide evidence for strong variations in the conditions of low temperature metamorphism in the Tethyan Himalaya metasediments between the Spiti river and the Tso Morari. Three sectors can be distinguished along the Spiti river-Tso Morari transect. In the SW, the Takling and Parang La area is characterised by a metamorphism around anchizone-epizone boundary conditions. Further north, in the Dutung area, the metamorphic grade abruptly decreases to weak diagenesis, with the presence of mixed-layered clay phases. At the end of the profile towards the NE, a progressive metamorphic increase up to greenschist facies is recorded, marked by the appearance of biotite and chloritoid. The combination of these data with the structural. observations permits to propose that a nappe stack has been crosscut by the younger Dutung-Thaktote extensional fault zone (DTFZ). The change in metamorphism across this zone helps to assess the displacements which occurred during synorogenic extension. In the SW and NE parts of the studied transect, a burial of 12 km has been estimated, assuming a geothermal gradient of 25 degrees C/km. In the SW part, this burial is due to the juxtaposition of the Shikar Beh and Mata nappes and in the NE part, solely to burial beneath the Mata nappe. In the central part of the profile, the effect of the DTFZ is to bring down diagenetic sediments in-between the two aforesaid metamorphic zones. The offset along the Dutung-Thaktote normal faults is estimated at 16 km.

Survival of zirconia- and metal-supported fixed dental prostheses: a systematic review

Purpose: The aim of this review was to systematically evaluate and compare the frequency of veneer chipping and core fracture of zirconia fixed dental prostheses (FOPS) and porcelain-fused-to-metal (PFM) FDPs and determine possible influencing factors. Materials and Methods: The SCOPUS database and International Association of Dental Research abstracts were searched for clinical studies involving zirconia and PFM FDPs. Furthermore, studies that were integrated into systematic reviews on PFM FDPs were also evaluated. The principle investigators of any clinical studies on zirconia FDPs were contacted to provide additional information. Based on the available information for each FOP, a data file was constructed. Veneer chipping was divided into three grades (grade 1 = polishing, grade 2 = repair, grade 3 = replacement). To assess the frequency of veneer chipping and possible influencing factors, a piecewise exponential model was used to adjust for a study effect. Results: None of the studies on PFM FDPs (reviews and additional searching) sufficiently satisfied the criteria of this review to be included. Thirteen clinical studies on zirconia FDPs and two studies that investigated both zirconia and PFM FDPs were identified. These studies involved 664 zirconia and 134 PFM FDPs at baseline. Follow-up data were available for 595 zirconia and 127 PFM FDPs. The mean observation period was approximately 3 years for both groups. The frequency of core fracture was less than 1% in the zirconia group and 0% in the PFM group. When all studies were included, 142 veneer chippings were recorded for zirconia FDPs (24%) and 43 for PFM FDPs (34%). However, the studies differed extensively with regard to veneer chipping of zirconia: 85% of all chippings occurred in 4 studies, and 43% of all chippings included zirconia FDPs. If only studies that evaluated both types of core materials were included, the frequency of chipping was 54% for the zirconia-supported FDPs and 34% for PFM FDPs. When adjusting the survival rate for the study effect, the difference between zirconia and PFM FDPs was statistically significant for all grades of chippings (P = .001), as well as for chipping grade 3 (P = .02). If all grades of veneer chippings were taken into account, the survival of PFM FDPs was 97%, while the survival rate of the zirconia FDPs was 90% after 3 years for a typical study. For both PFM and zirconia FDPs, the frequency of grades 1 and 2 veneer chippings was considerably higher than grade 3. Veneer chipping was significantly less frequent in pressed materials than in hand-layered materials, both for zirconia and PFM FDPs (P = .04). Conclusions: Since the frequency of veneer chipping was significantly higher in the zirconia FDPs than PFM FDPs, and as refined processing procedures have started to yield better results in the laboratory, new clinical studies with these new procedures must confirm whether the frequency of veneer chipping can be reduced to the level of PFM. Int J Prosthodont 2010;23:493-502

Événements et déformations tardi-métamorphiques dans le segment Ossola-Ticino (Val Vigezzo-Centovalli, Italie-Suisse)

RESUME: Une zone tectonique large et complexe, connue sous le nom de ligne des Centovalli, traverse le secteur des Alpes Centrales compris entre Domodossola et Locarno. Cette région, formée par le Val Vigezzo et la vallée des Centovalli, constitue la terminaison méridionale du dôme Lepontin et représente une portion de la zone des racines des nappes alpines. Elle fait partie d’une grande et complexe zone de cisaillement, en partie associée à des phénomènes hydrothermaux d’âge alpin (<20 Ma), qui comprend le système tectonique Insubrien et celui du Simplon. Le Val Vigezzo et les Centovalli constituent un vrai carrefour entre les principaux accidents tectoniques des Alpes ainsi qu'une zone de juxtaposition du socle Sudalpin avec la zone des racines de l’Austroalpin et du Pennique. Les phases de déformation et les structures géologiques qui peuvent être étudiées s'étalent sur une période comprise entre environ 35 Ma et l'actuel. L’étude détaillée de terrain a mis en évidence la présence de nombreuses roches et structures de déformation de type ductile et cassant tels que des mylonites, des cataclasites, des pseudotachylites, des kakirites, des failles minéralisées, des gouges de faille et des plis. Sur le terrain on a pu distinguer au moins quatre générations de plis liés aux différentes phases de déformation. Le nombre et la complexité de ces structures indiquent une histoire très compliquée, selon plusieurs étapes distinctes, parfois liées, voire même superposées. Une partie de ces structures de déformation affectent aussi les dépôts sédimentaires d’âge quaternaire, notamment des limons et des sables lacustres. Ces sédiments constituent les restes d'un bassin lacustre attribué à l'époque interglaciaire Riss/Würm (éemien, 67.000-120.000 ans) et ils affleurent dans la partie centrale de la zone étudiée, à l'Est de la plaine de Santa Maria Maggiore. Ces sédiments montrent en leur sein toute une série de structures de déformation tels que des plans de faille inverses, des structures conjuguées de raccourcissement et des véritables plis. Ces failles et ces plis représenteraient les évidences de surface d’une déformation probablement active en époque quaternaire. Une autre formation rocheuse a retenu tout notre attention; il s'agit d'un corps de brèches péridotitiques monogéniques qui affleure en discontinuité le long du versant méridional et le long du fond de la vallée Vigezzo sur environ 20 km. Ces brèches se posent indifféremment sur le socle (unités Finero, Orselina) ou sur les sédiments lacustres. Elles sont traversées par des plans de failles qui développent des véritables stries de faille et des gouges de faille; l’orientation de ces plans est la même que celle affectant les failles à gouges du socle. La genèse de cette brèche est liée à l'altération et au modelage glacier (rock-glaciers) d'une brèche tectonique originelle qui borde la partie externe du Corps de Finero. Les structures de déformation de cette brèche, pareillement à celles des sédiments lacustres, ont été considérées comme les évidences de surface d'une tectonique quaternaire active dans la région. La dernière phase de déformation cassante qui affecte cette région peut donc être considérée comme active en époque quaternaire. Une vue d’ensemble de la région étudiée nous permet de reconnaître à l’échelle régionale une zone de cisaillement complexe orientée E-W, parallèlement à l’axe de la vallée Centovalli-Val Vigezzo. Les données de terrain, indiquent que cette zone de cisaillement débute sous conditions ductiles et évolue en plusieurs étapes jusqu’à des conditions de failles cassantes de surface. La reconstruction de l'évolution géodynamique de la région a permis de définir trois étapes distinctes qui marquent le passage, de ce secteur de socle cristallin, de conditions P-T profondes à des conditions de surface. Dans ce contexte, on a reconnu trois phases principales de déformation à l’échelle régionale qui caractérisent ces trois étapes. La phase la plus ancienne est constituée par des mylonites en faciès amphibolite, associées à des mouvements de cisaillement dextre, qui sont ensuite remplacés par des mylonites en faciès schistes verts et des plis rétrovergentes liés au rétrocharriage des nappes alpines. Une deuxième étape est identifiée par le développement d’une phase hydrothermale liée à un système de failles extensives et décrochantes dextres à direction principale E-W, NE-SW et NW-SE. Leur caractérisation minéralogique a permis la mise en évidence des phases cristallines de néoformation liées à cet événement constituées par : K-feldspath (microcline), chlorites (Fe+Mg), épidotes, prehnite, zéolites (laumontite), sphène, calcite. Dans ce contexte, pour obtenir une meilleure caractérisation de cet événement hydrothermal on a utilisé des géothermomètres sur chlorites, sensible aussi à la pression et a la a(H2O), qui ont donné des valeurs descendantes comprises entre 450-200°C. Les derniers mouvements sont mis en évidence par le développement d’une série de plans majeurs de failles à gouge, qui forment une structure en sigmoïdes d’épaisseur kilométrique reconnaissable à l’échelle de la vallée et caractérisée par des mouvements transpressifs avec une composante décrochante dextre toujours importante. Cette phase de déformation forme un système conjugué de failles avec direction moyenne E-W qui coupent la zone des racines des nappes alpines, la zone du Canavese et le corps ultramafique de Finero. Ce système se déroule de manière subparallèle à l'axe de la vallée le long de plusieurs dizaines de kilomètres. Une analyse complète et détaillée des gouges de faille par XRD a montré que la fraction argileuse (<2 µm) de ces gouges contient une partie de néoformation très importante constituée par, des illites, des chlorites et des interstratifiés de type illite/smectite ou chlorite/smectite. Des datations avec méthode K-Ar sur ces illites ont donné des valeurs comprises entre 12 et 4 Ma qui représentent l'âge de cette dernière déformation cassante. L'application de la méthode de la cristallinité de l'illite (C.I.) a permis d'évaluer les conditions thermiques qui caractérisent le déroulement de cette dernière phase tectonique qui se produit sous conditions de température caractéristiques de l'anchizone et de la diagenèse. L'ensemble des structures de déformation qu'on vient de décrire s'insère parfaitement dans le contexte de convergence oblique entre la plaque adriatique et celle européenne qui à produit l'orogène alpin. On peut considérer les structures tectoniques du Val Vigezzo-Centovalli comme l'expression d'une zone majeure de cisaillement "Simplo-Insubrienne". L'empilement structural et les structures tectoniques affleurantes dans la région sont le résultat de l'interaction entre un régime tectonique transpressif et un régime transtensif. Ces deux champs de tension sont antagonistes entre eux mais sont reliés, de toute façon, à une seule phase décrochante dextre principale, due à une convergence oblique entre deux plaques. À l'échelle de l'évolution géodynamique on peut distinguer différentes étapes au cours desquelles les structures de ces deux régimes tectoniques interagissent en manière différente. En accord avec les données géophysiques et les reconstructions paléodynamiques prises dans la littérature on considère que la ligne Rhône-Simplon-Centovalli représente l'évidence de surface de la suture majeure profonde entre la plaque Adriatique et celle Européenne. Les vitesses de soulèvement qui ont été calculées dans cette étude pour cette région des Alpes donnent une valeur moyenne de 0.8 mm/a qui est tout à fait comparable avec les données proposées par la littérature sur cette zone. La zone Val Vigezzo-Centovalli peut être donc considérée comme un carrefour géologique où se croisent différentes phases tectoniques qui représentent les évidences de surface d'une suture profonde majeure entre deux plaques dans un contexte de collision continentale. ABSTRACT: A wide and complex tectonic zone known as Centovalli line, crosses the Central Alps sector between Domodossola and Locarno. This area, formed by the Vigezzo Valley and Centovalli valley, constitutes the southernmost termination of the Lepontin dome and represents a portion of the alpine nappes root zone. It belongs to a large and complex shear-zone, partly associated with hydrothermal phenomena of alpine age (<20 My), which includes the Insubric Line and the Simplon fault zone. Vigezzo Valley and Centovalli constitute a real crossroads between the mains alpines tectonics lines as well as a zone of juxtaposition of the Southalpine basement with the Austroalpin and Pennique root zone. The deformation phases and the geological structures that can be studied between approximately 35 My and the present. The detailed field study showed the presence of many brittle and ductile deformation structures and fault rocks such as mylonites, cataclasites, pseudotachylites, kakirites, mineralized faults, fault gouges and folds. In the field we could distinguish at least four folds generations related to the various deformation phases. The number and the complexity of these structures indicate a very complicated history, comprising several different stages, that sometimes are related and even superimposed. Part of these deformation structures affect also the sedimentary deposits of quaternary age, in particular the silts and sands lake deposit. These sediments constitute the remainders of a lake basin ascribed to the interglacial Riss/Würm (Eemien, 67.000-120.000 years) and outcroping in the central part of the studied area, in the Eastern part of Santa Maria Maggiore plain. These sediments show a whole series of deformation structures such as inverse fault planes, combined shortening structures and true folds. These faults and folds would represent the surface evidence of a probably active tectonic deformation in quaternary time. Another rock formation attracted all our attention. It is a body of monogenic peridotite breccia which outcrops in discontinuity along the southernmost slope and the bottom of the Vigezzo valley on approximately 20 km. This breccia lies indifferently on the basement (Finero and Orselina units) or on the lake sediments. They are crossed by fault planes which developed slikenside and fault gouges whose orientation is the same of the faults gouges in the alpine basement. This breccia results from the weathering and the surface modelling of an original tectonic breccia which borders the external part of Finero peridotite body. This breccia deformation structures, like those of the lake sediments, were regarded as the surface interaction of active quaternary tectonics in the area. So the last brittle deformation phases which affects this area seems to be actives in quaternary time. Theoverall picture of the studied area on a regional scale enables us to point out a complex shear-zone directed E-W, parallel to the axis of the Centovalli and Vigezzo Valley. The field analysis indicates that this shear-zone began under ductile conditions and evolved in several stages to brittle faulting under surface conditions. The analysis of the geodynamic evolution of the area allows to define three different stages which mark the transition of this alpine basement root zone, from deep P-T conditions to P-T surface conditions. In this context on regional scale three principal deformation phases, which characterize these three stages can be distinguished. The oldest phase consisted of the amphibolitie facies mylonites, associated to dextral strikeslip movements. They are then replaced by green-schists facies mylonites and backfolds related to the backthrusting of the alpines nappes. A second episode is caracterized by the development of an hydrothermal phase bound to an extensive fault and dextral strike-slip fault system, with E-W, NW-SE and SE-NW principal directionsThe principal neoformed mineral phases related to this event are: K-feldspar (microcline), chlorites (Fe+Mg), epidotes prehnite, zéolites (laumontite), sphene and calcite. In this context, to obtain a better characterization of this hydrothermal event, we have used an chlorite geothermometer, sensitive also to the pressure and has the a(H2O), which gave downward values ranging between 450-200°C. The last movements are caracterized by the development of important gouge fault plans, which form a sigmoid structure of kilometric thickness which is recognizable at the valley scale, and is characterized by transpressive movements always with a significant dextral strike-slip component. This deformation phase forms a combined faults system with an average E-W direction, which cuts trough the alpine root zone, the Canavese zone and the Finero ultramafic body. This fault system takes place subparallel to the axis of the valley over several tens of kilometers. A complete and detailed XRD analysis of the gouges fault showed that the clay fraction (<2µm) contains a very significant neo-formation of illite, chlorites and mixed layered clays such as illite/smectite or chlorite/smectite. The K-Ar datings of the illite fraction <2µm gave values ranging between 12 and 4 My and the illite fraction <0.2µm gave more recents values until to 2,4-0 My.This values represent the age of this last brittle deformation. The application of the illite crystallinity method (C.I.) allowed evaluating the thermal conditions which characterize this tectonic phase that occured under temperature conditions of the anchizone and diagenesis. The whole set of deformation structures which we just described, perfectly fit the context of oblique convergence between the Adriatic and the European plate that produced the alpine orogen. We can regard the Vigezzo valley and Centovalli tectonic structures as the expression of a major "Simplo-Insubric" shear-zone. Structural stacking and tectonic structures that outcrop in the studied area, are the result of the interaction between a transpressive and a transtensve tectonic phases. These two tension fields are antagonistic but they are also connected, in any event, with only one principal dextral strike-slip movement, caused by an oblique convergence between two plates. On the geodynamic evolution scale we can distinguish various stages during which these two tectonic structures fields interact in various ways. In agreement with the geophysical data and the paleodynamic recostructions taken in the literature we considers that the Rhone-Simplon-Centovalli line are the surface feature of the major collision between the Adriatique and the European plate at depth. The uplift speeds we calculated in this study for this Alpine area give an average value of 0.8 mm/a, which is in good agreement with the data suggested by the literature on this zone. TheVigezzo Valley and Centovalli zone can therefore be regarded as a geological crossroad where various tectonic phases are superimposed. They represent the evidences of a major and deeper suture between two plates in a continental collision context.

Kysyntävaihteluihin varautuminen metalliteollisuuden alihankintayrityksessä

Raportissa esitetään keinoja kysynnän vaihteluiden ehkäisemiseksi sekä vaihteluihin varautumiseksi metalliteollisuudessa alihankintayrityksessä. Keinot on jaoteltu sisäisiin ja ulkoisiin toimenpiteisiin. Sisäiset toimenpiteet on toteutettu yrityksen omassa tuotannossa ja niiden tarkoitus on kehittää valmistusprosesseja kokonaisuutena. Ulkoiset toimenpiteet on suunniteltu kehittämään kohdeyrityksen ja sen suurimman asiakkaan välistä yhteistyötä. Ratkaisukeinoja kehitettäessä raportissa tutustutaan prosessien merkitykseen toiminnan kuvaamisessa sekä ajan rooliin tilausohjautuvassa toiminnassa. Myös tilauksen kytkentäpisteen merkitystä toiminnan kehittämisessä pohditaan. Kysyntävaihteluiden perimmäisiä syitä analysoidaan ja esitellään toimintavaihtoehtoja kysyntävaihteluiden vähentämiseksi tai poistamiseksi. Kehitetyt toimenpiteet muodostavat kaksitasoisen ja kahdeksan pykäläisen ratkaisumallin. Ratkaisuista ulkoisia ovat toimintavastuiden uudelleenmäärittely, tilauskäytäntöjen kehittäminen, tiedon jakaminen sekä siirtyminen keskitettyihin toimitusratkaisuihin. Sisäiset ratkaisut ovat tuotantomuotojen uudelleenorganisointi, läpäisyajan parantaminen, resurssien tehokkaampi hyödyntäminen sekä prosessipohjaiset tuotannonohjausmenetelmät. Toimenpiteiden myötä kohdeyritys on tulevaisuudessa paremmin varautunut kohtaamaan vaihteluita kysynnässä. Yritys on sisäisesti joustavampi ja tehokkaampi ja omaa myös tehokkaita ulkoisia valmiuksia kysyntävaihteluiden varalle.

Comblike poly(a-alkyl g glutamate)s: computer simulation studies of an intermediate thermal phase.

Monte Carlo (MC) simulations have been used to study the structure of an intermediate thermal phase of poly(R-octadecyl ç,D-glutamate). This is a comblike poly(ç-peptide) able to adopt a biphasic structure that has been described as a layered arrangement of backbone helical rods immersed in a paraffinic pool of polymethylene side chains. Simulations were performed at two different temperatures (348 and 363 K), both of them above the melting point of the paraffinic phase, using the configurational bias MC algorithm. Results indicate that layers are constituted by a side-by-side packing of 17/5 helices. The organization of the interlayer paraffinic region is described in atomistic terms by examining the torsional angles and the end-to-end distances for the octadecyl side chains. Comparison with previously reported comblike poly(â-peptide)s revealed significant differences in the organization of the alkyl side chains.

De vegetatione notulae, III

Synusie and association. Application to the therophytic Mediterranean communities. The Agropyro-Lygeetum (=Eremopyro-Lygeetum) of the Ebro Basin is a two-layered community. The aerian organs of the chamaephytic and therophytic synusies appears mosaic-like distributed, but the roots of chamaephytes forms a continuous layer under the roots of spring therophytes. The structure of other Mediterranean therophytic associations is similar.

Fraktiointikerrostuksen vaikutus paperin laatuun

Työn tavoitteena oli kehittää prosessia fraktioinnista monikerrosperälaatikolle painopaperilajeilla. Tarkoituksena oli selvittää koeajojen avulla sihti- ja pyörrepuhdistusfraktioinnin soveltuvuutta paperin kerrostuksen kannalta. Työssä vertailtiin keskenään fraktiointimenetelmiä ja niiden yhdistelmiä. Tehtävänä oli prosessikonseptin kehittäminen eri prosessikytkennöistä ja –ratkaisuista simuloinnin avulla. Kirjallisuusosassa tutustuttiin analysoiden kirjallisuusviitteiden perusteella massan fraktiointiin ja paperin kerrostamiseen sekä fraktiointikerrostetun rainan karakterisointiin. Tavoitteiden saavuttamiseksi esikokeena suoritettiin pilotkoeajo hienopaperimassalla, jossa tutkittiin pääasiassa fraktiointitulosta. Toinen koeajo suoritettiin LWC-paperilla, jossa koekonekonsepti oli optimaalisempi kerrostuksen kannalta ja fraktiointitulos voitiin linkittää paperin laatusuureisiin. LWC-koeajossa fraktioidulla massalla tehtiin laboratoriomittakaavassa monikerrosarkkimuottikokeita, joiden tuloksilla pyrittiin vahvistamaan koeajosta saatuja tuloksia ja fraktioinnnin potentialia. Prosessikonseptin kehittämiseksi rakennettiin seitsemän simulointimallia eri kytkennöistä. Malleja verrattiin keskenään täyteaine- ja kuitujakeiden fraktiointikyvyn perusteella. Koeajojen avulla selvitettiin fraktioinnin kannalta optimaaliset prosessimuuttujat. Fraktiointikerrostuksella parannettiin paperin z-suuntaista lujuutta ja etenkin pyörrepuhdistinfraktioinnilla pintojen sileyttä. Fraktiointikerrostuksella voitiin parantaa paperin täyteainejakaumaa. Kokeiden perusteella huomattiin, että kukin paperilaji tarvitsee erilaisen fraktiointijärjestelyn riippuen käytetystä massasta ja täyteaineesta.