Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Comparative study of the different degrees of risk of gastrointestinal stromal tumor

OBJECTIVE: To evaluate the applicability of the main categories of risk and morphological factors in the prognosis of gastrointestinal stromal tumors. METHODS: we retrospectively studied fifty-four cases of GIST, assessing the main prognostic factors of this neoplasis: risk levels, topography, size, mitotic index, necrosis, histological subtype and immunophenotype. We also verified their association and the reduction of overall survival. RESULTS: Univariate analysis showed that tumors with mitoses number greater than 5 per 50CGA (high-power fields), the presence of necrosis and a high risk for both the systems proposed by Fletcher and Miettinen had a significant association with reduced survival (p = 0.00001, 0.0056, 0.03 and 0.009, respectively). The remaining analyzed factors (size, histological subtype, topography and immunophenotype) had no such association. Multivariate analysis (Jacard index) showed that the Miettinen degree of risk was the one that best correlated with prognosis. CONCLUSION: the risk criteria of Fletcher and Miettinen are important in assessing the prognosis of patients with gastrointestinal stromal tumors, especially the latter, which adds to the mitotic index and the presence of tumor necrosis.

Essays on auditor independence

Auditor independence is a cornerstone of the auditing profession and the basic principle that underpins the reputation of the auditing profession in the public eye. Indeed, it is the attribute most demanded from auditors by the public. Therefore, the sustainability of the auditing profession depends on how auditors can protect this principle. This dissertation consists of four interrelated essays concerned with auditor independence. Specifically, it examines situations that can threaten and impair auditor independence. In addition, this dissertation also examines several variables that may enhance and protect auditor independence. The first essay aims to examine the impact of social pressures occurring within audit firms on auditors’ judgment in the setting of a society with “high power distance” and “low individualism” cultural dimensions. The social pressures consisted of obedience pressure exerted by an auditor’s superior and conformity pressure exerted by an auditor’s colleague. Moreover, two moderating variables—a multi-dimensional professional commitment and locus of control—were included as moderator variables in the relationship between the social pressures faced by auditors and their judgment. The findings show that obedience and conformity pressures influence auditor judgment. Auditors who face the social pressures will make a judgment that may be even diametrically opposite to the independence principle. The findings also indicate that a multi-dimensional professional commitment and locus of control may potentially influence auditor judgment in a situation with social pressures. The second essay aims to investigate the association of advocacy and familiarity threats caused by auditor fee dependence and auditor tenure on auditor independence based on Finnish data, law, and auditing environment. This essay was motivated by the Green Paper on Audit Policy, published by the European Commission in 2010 that questions whether the maximum fee collected from a client should be regulated and whether consecutive assignments should be limited, among others. Contrary to popular belief, this essay does not find evidence that audit fees and long auditor tenure will jeopardise auditor independence. Therefore, the findings do not support policies to regulate auditor fees or limit auditor tenure in Finland. The third essay aims to examine the effect of client intimidation on auditor independence in an audit-client conflict situation. Intimidation threat is one of five independence threats that are explicitly referenced in the IFAC’s independence framework. Client intimidation was manifested in the client threatening to replace the auditor if the auditor did not adopt the client’s position. In addition, this essay examines the role of auditor’s perceived pressure and multi-dimensions of professional commitment as moderator variables. The findings suggest that auditors who experience client intimidation in an audit conflict situation are more likely to have their independence impaired than those who are in a similar situation but without client intimidation. Moreover, auditors who experience client intimidation perceive higher pressure than those who do not experience intimidation. Finally, auditors’ affective and continuance professional commitment dimensions moderate the relationship between auditors’ perceived pressures and auditor independence. The aim of the fourth essay is twofold. First, it aims to develop a scale for measuring auditors’ reputation awareness. Second, it aims to examine the correlation between the levels of auditor reputation awareness and auditor independence. A seven-item scale was developed as the reputation awareness scale. The findings indicate that the scale consists of one dimension. It also has a level of satisfactory reliability and a high level of validity. The findings show that there is a positive correlation between the level of auditors’ reputation awareness and auditor independence.

Wind Turbine Direct-Drive Permanent-Magnet Generator with Direct Liquid Cooling for Mass Reduction

Today’s electrical machine technology allows increasing the wind turbine output power by an order of magnitude from the technology that existed only ten years ago. However, it is sometimes argued that high-power direct-drive wind turbine generators will prove to be of limited practical importance because of their relatively large size and weight. The limited space for the generator in a wind turbine application together with the growing use of wind energy pose a challenge for the design engineers who are trying to increase torque without making the generator larger. When it comes to high torque density, the limiting factor in every electrical machine is heat, and if the electrical machine parts exceed their maximum allowable continuous operating temperature, even for a short time, they can suffer permanent damage. Therefore, highly efficient thermal design or cooling methods is needed. One of the promising solutions to enhance heat transfer performances of high-power, low-speed electrical machines is the direct cooling of the windings. This doctoral dissertation proposes a rotor-surface-magnet synchronous generator with a fractional slot nonoverlapping stator winding made of hollow conductors, through which liquid coolant can be passed directly during the application of current in order to increase the convective heat transfer capabilities and reduce the generator mass. This doctoral dissertation focuses on the electromagnetic design of a liquid-cooled direct-drive permanent-magnet synchronous generator (LC DD-PMSG) for a directdrive wind turbine application. The analytical calculation of the magnetic field distribution is carried out with the ambition of fast and accurate predicting of the main dimensions of the machine and especially the thickness of the permanent magnets; the generator electromagnetic parameters as well as the design optimization. The focus is on the generator design with a fractional slot non-overlapping winding placed into open stator slots. This is an a priori selection to guarantee easy manufacturing of the LC winding. A thermal analysis of the LC DD-PMSG based on a lumped parameter thermal model takes place with the ambition of evaluating the generator thermal performance. The thermal model was adapted to take into account the uneven copper loss distribution resulting from the skin effect as well as the effect of temperature on the copper winding resistance and the thermophysical properties of the coolant. The developed lumpedparameter thermal model and the analytical calculation of the magnetic field distribution can both be integrated with the presented algorithm to optimize an LC DD-PMSG design. Based on an instrumented small prototype with liquid-cooled tooth-coils, the following targets have been achieved: experimental determination of the performance of the direct liquid cooling of the stator winding and validating the temperatures predicted by an analytical thermal model; proving the feasibility of manufacturing the liquid-cooled tooth-coil winding; moreover, demonstration of the objectives of the project to potential customers.

Modal testing and numerical modeling of the dynamic properties of layered sheet-steel structure

Recently, due to the increasing total construction and transportation cost and difficulties associated with handling massive structural components or assemblies, there has been increasing financial pressure to reduce structural weight. Furthermore, advances in material technology coupled with continuing advances in design tools and techniques have encouraged engineers to vary and combine materials, offering new opportunities to reduce the weight of mechanical structures. These new lower mass systems, however, are more susceptible to inherent imbalances, a weakness that can result in higher shock and harmonic resonances which leads to poor structural dynamic performances. The objective of this thesis is the modeling of layered sheet steel elements, to accurately predict dynamic performance. During the development of the layered sheet steel model, the numerical modeling approach, the Finite Element Analysis and the Experimental Modal Analysis are applied in building a modal model of the layered sheet steel elements. Furthermore, in view of getting a better understanding of the dynamic behavior of layered sheet steel, several binding methods have been studied to understand and demonstrate how a binding method affects the dynamic behavior of layered sheet steel elements when compared to single homogeneous steel plate. Based on the developed layered sheet steel model, the dynamic behavior of a lightweight wheel structure to be used as the structure for the stator of an outer rotor Direct-Drive Permanent Magnet Synchronous Generator designed for high-power wind turbines is studied.

Permanent magnet synchronous generator design solution for large directdrive wind turbines: Thermal behavior of the LC DD-PMSG

Wind is one of the most compelling forms of indirect solar energy. Available now, the conversion of wind power into electricity is and will continue to be an important element of energy self-sufficiency planning. This paper is one in a series intended to report on the development of a new type of generator for wind energy; a compact, high-power, direct-drive permanent magnet synchronous generator (DD-PMSG) that uses direct liquid cooling (LC) of the stator windings to manage Joule heating losses. The main param-eters of the subject LC DD-PMSG are 8 MW, 3.3 kV, and 11 Hz. The stator winding is cooled directly by deionized water, which flows through the continuous hollow conductor of each stator tooth-coil winding. The design of the machine is to a large degree subordinate to the use of these solid-copper tooth-coils. Both steady-state and timedependent temperature distributions for LC DD-PMSG were examined with calculations based on a lumpedparameter thermal model, which makes it possible to account for uneven heat loss distribution in the stator conductors and the conductor cooling system. Transient calculations reveal the copper winding temperature distribution for an example duty cycle during variable-speed wind turbine operation. The cooling performance of the liquid cooled tooth-coil design was predicted via finite element analysis. An instrumented cooling loop featuring a pair of LC tooth-coils embedded in a lamination stack was built and laboratory tested to verify the analytical model. Predicted and measured results were in agreement, confirming the predicted satisfactory operation of the LC DD-PMSG cooling technology approach as a whole.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Doubly fed wind turbine performance in variable grid conditions

Wind turbines based on doubly fed induction generators (DFIG) become the most popular solution in high power wind generation industry. While this topology provides great performance with the reduced power rating of power converter, it has more complicated structure in comparison with full-rated topologies, and therefore leads to complexity of control algorithms and electromechanical processes in the system. The purpose of presented study is to present a proper vector control scheme for the DFIG and overall control for the WT to investigate its behavior at different wind speeds and in different grid voltage conditions: voltage sags, magnitude and frequency variations. The key principles of variable-speed wind turbine were implemented in simulation model and demonstrated during the study. Then, based on developed control scheme and mathematical model, the set of simulation is made to analyze reactive power capabilities of the DFIG wind turbine. Further, the rating of rotor-side converter is modified to not only generate active rated active power, but also to fulfill Grid Codes. Results of modelling and analyzing of the DFIG WT behavior under different speeds and different voltage conditions are presented in the work.

Loistehon kompensoinnin ja yliaaltosuodattimien nykytila sekä kehityskohteet Kemira Chemicals Oy:n Joutsenon tehtaalla

Tutkimuksessa käsitelty kemikaalitehdas on 110 kV:n kantaverkkoon liittyvä tehointensiivinen teollisuuslaitos. Prosessien käyttöön mukautetut sähkönjakeluverkon yliaaltosuodattimet ja niiden käyttökytkennät ovat tärkeässä asemassa loistehon tuoton hallitsemiseksi liittymän loistehoikkunaan ja riittävän yliaaltosuodatuksen järjestämiseksi häviöt minimoiden. Kohteena olleen kemikaalitehtaan sähkönjakeluverkon kompensointia ja yliaaltosuodatusta on viimeksi tutkittu vuonna 2003. Tämän jälkeen verkostokomponentit ovat ikääntyneet, prosessien käyttö sekä pienjänniteverkko ovat muuttuneet ja tehdasta käyttävät osittain eri henkilöt. Nykytilaselvitykselle ja verkon kehityskohteiden analysoinnille on tullut tarve edellisen selvityksen jatkoksi. Tutkimus painottuu vahvasti kenttämittauksiin, joiden perusteella sekä kirjallisuutta ja tehtaan järjestelmiä hyödyntäen määritetään loistehotasot verkon keskeisimmissä kohteissa pien-, keski- ja suurjännitetasoilla. Tutkimuksessa esitetään lipeätehtaan suotimien uudelleenjärjestely 4. yliaallon vähentämiseksi ja yksikkökoon pienentämiseksi. Kantaverkon liittymäpisteen tilanne oli hyväksyttävä. Tutkimus esittää pienjännitekompensointia KF-4-100 keskukseen varayhteyden kapasiteettia lisäten. Tutkimus tuotti yleistietoutta verkon käytöstä ja selvitti parhaat käyttökytkennät loistehoikkunan hallitsemiseksi ilman loistehokustannuksia.

Investigation of femtosecond laser technology for the fabrication of drug nanocrystals in suspension

La technique du laser femtoseconde (fs) a été précédemment utilisée pour la production de nanoparticules d'or dans un environnement aqueux biologiquement compatible. Au cours de ce travail de maîtrise, cette méthode a été investiguée en vue d'une application pour la fabrication de nanocristaux de médicament en utilisant le paclitaxel comme modèle. Deux procédés distincts de cette technologie à savoir l'ablation et la fragmentation ont été étudiés. L'influence de la puissance du laser, de point de focalisation, et de la durée du traitement sur la distribution de taille des particules obtenues ainsi que leur intégrité chimique a été évaluée. Les paramètres ont ainsi été optimisés pour la fabrication des nanoparticules. L’évaluation morphologique et chimique a été réalisée par microscopie électronique et spectroscopie infrarouge respectivement. L'état cristallin des nanoparticules de paclitaxel a été caractérisé par calorimétrie differentielle et diffraction des rayons X. L'optimisation du procédé de production de nanoparticules par laser fs a permis d'obtenir des nanocristaux de taille moyenne (400 nm, polydispersité ≤ 0,3). Cependant une dégradation non négligeable a été observée. La cristallinité du médicament a été maintenue durant la procédure de réduction de taille, mais le paclitaxel anhydre a été transformé en une forme hydratée. Les résultats de cette étude suggèrent que le laser fs peut générer des nanocristaux de principe actif. Cependant cette technique peut se révéler problématique pour des médicaments sensibles à la dégradation. Grâce à sa facilité d'utilisation et la possibilité de travailler avec des quantités restreintes de produit, le laser fs pourrait représenter une alternative valable pour la production de nanoparticules de médicaments peu solubles lors des phases initiales de développement préclinique. Mots-clés: paclitaxel, nanocristaux, laser femtoseconde, ablation, fragmentation

TIC et formation des enseignants du fondamental en Haïti : barrières et facteurs facilitants

La réalisation des objectifs d’Éducation pour tous en Haïti requiert impérativement, entre autres, une campagne massive et accélérée de formation d’enseignants - formation à la fois initiale et en cours d’emploi. Malheureusement, les structures actuelles sont loin d’être en mesure de répondre à cette demande. Il faudra donc recourir à d’autres modalités de formation, particulièrement celles utilisant les TIC (technologies de l’information et de la communication). Cependant, dans ce domaine, il est fort tentant de continuer à copier ce qui se fait en France, au Canada ou aux États-Unis, et d’allonger ainsi la liste d’échecs dus à une adaptation déficiente ou inexistante. Dans un souci de maximiser les chances de succès, il est important d’examiner l’adéquation des stratégies adoptées au contexte et à l’apprenant haïtiens. Cette recherche étudie les caractéristiques des enseignants haïtiens des deux premiers cycles de l’enseignement fondamental (primaire) en tant qu’apprenants, caractéristiques susceptibles de constituer des barrières ou des facteurs facilitants internes à une intégration efficace des TIC dans leur formation. Dans une première phase quantitative, une enquête a été administrée en 2009-2010 à 176 enseignants. L’analyse des données recueillies a permis de faire ressortir trois tendances fortes : une attitude positive par rapport aux innovations et aux TIC, des sources intrinsèques de motivation et une forte distance hiérarchique ; il faut aussi signaler deux autres résultats importants : le peu de familiarité avec l’ordinateur et l’adoption massive du cellulaire ; les réponses étaient plus partagées au niveau de la conception de l’enseignement et de l’apprentissage et de la dimension individualisme-collectivisme. Une analyse factorielle a fait émerger quatre facteurs : la capacité d’utiliser les TIC, le désir de changement, la conception du rôle du formateur et la distance hiérarchique. Suite à cette enquête, une phase qualitative comportant sept entrevues individuelles avec des spécialistes de la formation des enseignants en Haïti et trois groupes de discussion avec des enseignants du fondamental a été effectuée à la fin de 2010. Cette phase avait pour but d’enrichir, de compléter, d’expliquer, de confirmer et d’illustrer les résultats quantitatifs. Malgré leur regard plus sévère, les spécialistes en formation des enseignants ont largement contribué à l’interprétation des résultats, particulièrement ceux concernant l’attitude par rapport aux innovations et aux TIC, la dimension individualisme-collectivisme et la conception de l’enseignement et de l’apprentissage. Quant aux participants aux groupes de discussion, ils ont globalement appuyé les résultats de la phase quantitative, mais en expliquant et en nuançant certains aspects. Ils ont particulièrement renforcé l’importance de deux facteurs qui ne figuraient pas dans la liste initiale et qui ont émergé de l’analyse factorielle : le désir de changement et la conception du rôle du formateur. Ils ont également apporté des éclaircissements fort pertinents sur la distance hiérarchique. .

Linear block copolymers of L–lactide and 2–dimethylaminoethyl methacrylate : synthesis and properties

Part of the research described in this thesis is conducted in collaboration with Centre d' étude et de Recherche sur les Macromolécules (CERM), Université de Liège, Sart-Tilman, Belgium

FPGA-based object detection using classification circuits

Dans l'apprentissage machine, la classification est le processus d’assigner une nouvelle observation à une certaine catégorie. Les classifieurs qui mettent en œuvre des algorithmes de classification ont été largement étudié au cours des dernières décennies. Les classifieurs traditionnels sont basés sur des algorithmes tels que le SVM et les réseaux de neurones, et sont généralement exécutés par des logiciels sur CPUs qui fait que le système souffre d’un manque de performance et d’une forte consommation d'énergie. Bien que les GPUs puissent être utilisés pour accélérer le calcul de certains classifieurs, leur grande consommation de puissance empêche la technologie d'être mise en œuvre sur des appareils portables tels que les systèmes embarqués. Pour rendre le système de classification plus léger, les classifieurs devraient être capable de fonctionner sur un système matériel plus compact au lieu d'un groupe de CPUs ou GPUs, et les classifieurs eux-mêmes devraient être optimisés pour ce matériel. Dans ce mémoire, nous explorons la mise en œuvre d'un classifieur novateur sur une plate-forme matérielle à base de FPGA. Le classifieur, conçu par Alain Tapp (Université de Montréal), est basé sur une grande quantité de tables de recherche qui forment des circuits arborescents qui effectuent les tâches de classification. Le FPGA semble être un élément fait sur mesure pour mettre en œuvre ce classifieur avec ses riches ressources de tables de recherche et l'architecture à parallélisme élevé. Notre travail montre que les FPGAs peuvent implémenter plusieurs classifieurs et faire les classification sur des images haute définition à une vitesse très élevée.

Short Isora Fibre Reinforced Natural Rubber Composites

The present study deals with the short isora fibre reinforced natural rubber composites. In recent years there has been a tremendous advancement in the field of science and technology of short fibre reinforced polymer composites. The low density, high strength, high stiffness to weight ratio, excellent durability and design flexibility are the primary reasons for their use in many diversified fields such as air crafts, automobiles, marine industry etc. Compared to the various natural and synthetic fibres used as reinforcement for elastomer composites isora fibre is superior in many aspects. `Isora' is a natural lignocellulosic fibre which is easily available in South India especially in Kerala. The fibre is separated from the bark of the Helicteres isora plant by retting process. This fibre has excellent mechanical properties and is easily amenable to physical and chemical modifications. The study shows that composites with poor interfacial bonding tend to dissipate more energy than that with to interfacial bonding. The mechanical loss also can be related to interfacial bonding. The effect of chemical treatment of isora fibre on damping was also studied. Both in the low and high temperature region which indicates that this composite posseses low damping and hence good interfacial bonding characteristics. Hence these composites are better candidates for high damping applications. Composites with longitudinally oriented fibres showed high storage modulus than transversely oriented ones due to the effective stress transfer between fibre and matrix.

Optical Emission Diagnostics Of Laser Produced Plasma From Graphite And Yba2cu3o7

This thesis is entitled “OPTICAL EMISSION DIAGNOSTICS OF LASER PRODUCED PLASMA FROM GRAPHITE AND YBa2Cu3O7. The work presented in this thesis covers the experimental results on the plasma produced with moderately high power laser with irradiance range in between 10 GW cm 2 to 100 GW cm -2. The characterization of laser produced plasma from solid targets viz. graphite and high temperature superconducting material like YBa2Cu3O7 have been carried out. The fundamental frequency from a Q - switched Nd: YAG laser with 9 ns pulse duration is used for the present studies. Various optical emission emission diagnostic techniques were employed for the the characterization of the LPP which include emission spectroscopy, time resolved studies, line broadening method etc. In order to understand the physical nature of the LPP like recombination, collisional excitation and the laser interaction with plasma, the time resolved studies offer the most logical approach