运用MC-ICP-MS测定天然样品的锂同位素组成

自然界锂同位素分馏强烈，这使得它在很多方面都得到了应用，如地球化学、天体化学和核工业等。所有这些领域都要求精确的测定6Li/7Li的比值。但由于锂是微量元素，而且在测试过程中还存在明显的干扰，因此在进行锂同位素比值测定之前必须对样品进行分离和富集。本文以锂元素标准样品和钾、钠、钙、镁元素标准样品的混合溶液为主要研究对象，采用阳离子交换树脂AG-50W-X8来分离富集锂，探索在不同淋洗介质条件下锂分离纯化的最佳介质条件。初步得出以下结论： 1、本次研究建立了相对简单、高效的锂同位素分离方法。用单一的柱子分离、提纯样品锂；用低浓度的盐酸（0.15M HCl）直接作为淋洗介质，操作过程简单。 2、对锂同位素比值测定产生潜在影响因素，如基体效应、回收率、流程空白等进行了实验研究，证实这些影响因素对于本次研究所建立的方法来说都是可以忽略不计的。 3、用MC-ICP-MS测定样品的锂同位素组成，分析结果的准确度和精度与现阶段所报道数据相同。测定海水的锂同位素组成（+31.6±1.0‰，2σ）与Tomoscak 等（+31.8±1.9‰，2σ）的分析值相近。 4、该方法也适用于低含量的样品。我们分离并测定了不同类型样品的锂同位素组成，样品锂含量在0.064µg/g和132µg/g之间，说明该方法也同样适用于低含量地质样品的分析测定。

贵州省遵义市大气降水中有机和无机地球化学特征研究

正确认识降水中的化学组分是评价酸雨和大气环境质量的重要途径，降水中低分子有机酸的研究是认识C、H、O等元素生物地球化学循环和酸雨成因的重要内容。贵州省遵义市作为我国酸雨高发地区，是降水化学组成尤其是低分子有机酸地球化学循环研究的典型区域。我们在遵义市进行了为期一年(2006年5月~2007年4月)的降水采集(共76个样品)，对pH值、电导率和主要的阴离子(包括有机和无机)、阳离子进行了测定，并进行了分析和讨论。 (1) pH和电导率的雨量加权平均值分别为4.11(范围：2.30~ 6.04)和62.10 μs•cm-1 (范围：6.60 ~ 1630.00 μs•cm-1)，酸雨频率高达93.2%，pH存在着显著的季节变化，其中冬季pH值最低，表明遵义市酸雨污染较为严重，冬季为最。 (2) 遵义市监测期间离子浓度的大小顺序为SO42-> Ca2+> H+> NH4+> NO3-> Cl-> F->HCOO-> Mg2+> K+> CH3COO-> Na+> (COO)22-> PO43-> NO2-，其中SO42-、Ca2+、H+、NH4+、NO3-是最主要离子，浓度分别为148.15 μmol•L-1、81.89 μmol•L-1、77.74 μmol•L-1、43.80 μmol•L-1和31.50μmol•L-1，它们分别占离子总量的31.97%、17.67%、16.78%、9.45%和6.54%；遵义市大气降水中主要的致酸物质是SO42-和NO3-，主要的缓冲物质是Ca2+和NH4+，大气污染类型属硫酸钙型。相对酸度和中和因子结果表明降水中仅有77%的降水酸度被碱性物质(以Ca2+和NH4+为主)中和；因子分析中H+、NO3-、nss-SO42-(非海源性硫酸根)、NH4+归为一组，再次表明SO42-和NO3-对降水酸度的重要贡献。富集系数和源的贡献分析表明，SO42-和NO3-主要来自人为活动的贡献，SO42-来源主要包括工业、民用的燃煤燃烧释放的SO2，NO3-主要是遵义市电厂和其它工厂向大气中排放的NOx的化学转化而成。Ca2+主要来自于遵义市的土壤及水泥厂等的排放；Mg2+主要来自陆源输入，部分来自海水的贡献。氮肥生产、大面积农田化肥的使用以及生物排放源很可能是该地区降水中NH4+的主要污染源。值得注意的是，作为海盐性离子的Cl-，在遵义市降水中重要的部分还是人为活动，主要是遵义工厂(如碱厂和钛厂)向大气中排放的HCl和Cl2转化而成。无机离子浓度的季节变化表明，对于遵义市，需要逐步改变能源结构尤其是冬季工业、居民燃煤的使用，才能有效地改善遵义市当前的环境污染。 (3) 遵义市降水中含量较高的常见有机酸是[HCOO-]T、[CH3COO-]T和[(COO)22-]T，它们的雨量加权平均值各为9.29 μmol•L -1、6.47 μmol•L-1和5.06 μmol•L-1；遵义市区降水中有机酸总浓度为22.28 μmol•L-1，占阴离子总量的9.39 %；遵义市降水中四季的有机酸浓度由高到低分别为：春季>冬季>秋季>夏季。以上结果表明，遵义市的有机酸是降水中的重要组成部分，其浓度存在明显的季节性变化。在一次降雨事件中，有机酸的浓度一般随降雨时间的延长而降低，但在降雨中后期有时会出现上升的现象，表明有机酸主要来自云下淋滤作用，少数情况下来自大气远距离的传输。 (4) 相关性分析发现甲酸和乙酸具有强烈的正相关(r= 0.86)，表明甲酸和乙酸具有共同的来源。有机酸与降水中的主要无机离子NO3-、nss-SO42-、K+、Na+、Ca2+等存在着中度相关，表明有机酸的来源与人为活动有着重要的关系。应用气液平衡的原理，提出了降水中甲酸、乙酸比值(F/A)aq的有机酸来源判定方法。发现遵义降水中的有机酸春季和冬季主要来自人类活动的释放，其中春季主要来自遵义市南郊的工业污染，由南方水汽(占春季总量的54%)将其污染物传输至遵义市中心城区，冬季主要是大量燃煤的燃烧释放；夏季和秋季则主要来自植物的释放，其中秋季中的部分有机酸也受到华中和华东地区(其气团占秋季总量的45%)的远距离影响。而遵义市区的山间盆地地形、高湿度、高静风率和低风速、以尘埃为主的大气污染物和有机酸的短生命周期(几小时~几天)为有机酸来源于当地创造了有利条件。 (5) 根据热力学平衡计算新方法，发现遵义市pH≤5的降水中甲酸和乙酸对自由酸度的贡献分别为14.79% (范围：0.42~91.14%)、3.66% (范围：0.02~31.55%)。对比显示，遵义市的有机酸贡献量低于边远地区，主要由于遵义市降水的低pH值和高无机酸度所致。在春、夏、秋、冬季节，降水中的有机酸对自由酸度的平均贡献值分别为31.95%、26.16%、8.02%、11.17%，表明有机酸酸度有着明显的季节性差异，春季有机酸的高贡献量主要受降水中的有机酸高含量、低水温和高pH值的共同作用，夏季受高pH值的影响，而秋季和冬季的低贡献量主要受降水的低pH值所控制。 (6) 在遵义市的沉降通量中，无机离子的湿沉降通量占所有离子湿沉降总量的94%，并存在明显的季节性变化。SO42-、Ca2+、H+、NH4+、NO3-为最主要的贡献者，分别为90.1、49.8、47.3、26.0和19.2 mmol•m-2•yr-1。对比显示，SO42-、Ca2+、H+的沉降量均属于我国的高值区，而NO3-的沉降量属于我国中值区，NH4+的沉降量属我国低值水平。营养元素总无机氮TIN(TIN= NH4+ -N+ NO3- -N+ NO2- -N)的湿沉降总量为45.7 mmol•m-2•yr-1，其中NH4+和NO3-分别占TIN的57.0%和41.9%，遵义地区高TIN值当地氮肥的施用量和工业NOx的释放量密不可分；营养元素P的沉降量为1.97 mmol•m-2•yr-1，由于P的来源较少，促使P的湿沉降通量较低。有机酸占湿沉降总量的6%，其四季的湿沉降量顺序由高到低依次为：春>秋>冬>夏，这是有机离子的浓度和四季的降雨量共同作用的结果。根据气液平衡理论可知，挥发性有机酸(HCOO-、CH3COO-和CH3CH2COO-)的干沉降量占总沉降量的47.2%，表明遵义市有机酸沉降方式包括干湿沉降两种。因此在研究遵义市的污染物尤其是有机酸类对生态系统和城市建设的影响时，有必要同时收集气样和水样。

锡在流体和花岗质熔体间分配行为的实验研究

锡矿床是与花岗岩在时间、空间、成因上有着密切联系的典型矿种之一。与锡矿有关的花岗岩多具有过铝、富钾、硅含量高的特征。传统观点认为与锡矿有关的花岗岩主要是S型花岗岩，可是近年在国内外相继发现了许多具有重要经济价值的锡矿床与富碱侵入岩有着密切成因联系。与富碱侵入岩有关的锡成矿作用日益受到地质学家的重视，锡矿床与富碱侵入岩的关系已成为研究热点之一，相关的研究工作虽然取得了很大的进展，但是富碱侵入岩体能否分异出富锡成矿流体还存在争议。研究表明，与岩浆岩有关的成矿与岩浆演化过程中成矿元素在流体-熔体相间的分配行为有着密切的关系。成矿元素在流体-熔体相间的分配行为除受到温度、压力及氧逸度等物理化学条件的制约外，还受到岩浆熔体成份及岩浆分异出来的流体化学组成的影响。以往有关锡在流体-熔体相间分配行为的实验研究主要侧重于改变流体相来观测锡的分配系数，且多为单一的含氯或含氟岩浆体系，这制约了对岩浆演化过程中元素在流体-熔体相间分配行为的深入认识。本文通过改变流体相、熔体相的化学组成，开展了一系列锡在流体和花岗质熔体相间分配行为的实验研究。综合分析了锡在晶体-熔体-流体间的分配行为，并结合地质实际探讨与富碱侵入岩有关的锡成矿的物理化学条件和成矿机理。研究成果对深入认识与花岗岩有关锡矿的成矿机理、丰富和完善与花岗岩有关的锡成矿理论、为进一步探索与花岗岩有关的锡成矿规律提供重要的实验依据。此外，实验对进一步推动实验地球化学学科发展具有重要意义。 实验在中国科学院地球化学研究所矿床地球化学国家重点实验室的成矿实验室完成，主要实验设备为快速内冷（RQV）高压釜。实验的温度为850℃，压力100MPa、氧逸度接近NNO。实验首先采用人工合成硅酸盐凝胶的方法制成具有不同化学组成的花岗质熔体，使用分析纯化学试剂配制不同成分和不同浓度的溶液，分别作为实验初始固液相。主要开展了三方面的实验研究：1．熔体相组成不变，以改变流体相组成来观察锡的分配行为。这组实验固相初始物为过碱质富钾的硅酸盐，初始液相分别为NaCl、KCl、HCl、HF、去离子水溶液；2．流体相组成不变，改变熔体化学组成观察锡分配行为。初始液相选用低浓度的0.1mol/L HCl溶液，熔体相为具不同化学组成的凝胶（其中一组改变熔体碱质含量和铝饱和指数ASI、另一组改变熔体钠钾摩尔比值）；3．氟氯共存含水的花岗质岩浆体系中氟氯含量相对变化时锡分配行为。实验通过改变熔体相中氟含量和液相盐酸溶液的浓度来观察锡在含氟硅酸盐熔体和不同浓度盐酸溶液间的分配行为。氟主要以(NaF+KF)混合物的形式加入初始固相中。实验研究结果表明： 1．流体相络阴离子种类及含量对锡在流体-熔体相间的分配行为有着明显的影响。当流体相中络阴离子Cl－、F－含量增大时，有利于增大锡在流体-熔体相间的分配系数；尤其当流体为富氯的酸性流体时，锡在流体-熔体相间的分配系数随液相中HCl浓度的增大而增大并存在关系式logD Sn=2.0247×log[HCl]＋0.6717（[HCl]的单位为mol/L），锡在流体相中主要以二价锡氯配合物的形式迁移，锡倾向于分配进入富氯的酸性流体中。此外，富氯酸性流体与共存的熔体反应后，熔体中的碱质含量降低，铝饱和指数增大。 2．熔体化学组成对锡在熔体相/流体相的分配行为有着明显的影响。D Sn随着熔体中碱质含量增大而减小：D Sn=－0.0489×MAlk＋0.4516, R2=0.98（MAlk为熔体中Na2O+K2O摩尔含量），表明富碱质熔体有利于锡在熔体相中富集，从而可能为锡矿形成提供矿质来源。D Sn随熔体ASI值的增大而增大：D Sn=0.1886×ASI－0.1256, R2=0.99，即过铝质熔体相对有利于锡分配进入流体相中。过铝质熔体中碱质总量及其它组分相对不变的前提下，熔体钠钾摩尔比值越高D Sn越小：D Sn=－0.0314×RNa/K＋0.0483, R2=0.82（RNa/K为Na/K摩尔比值），富钠的熔体有利于锡分配进入熔体相，而富钾的熔体却相对有利于锡分配进入流体相中。 3．在氟氯共存花岗质岩浆体系中：①熔体相中氟含量对氯在流体-熔体相间的分配有着明显影响，熔体中氟含量降低有利于氯分配进入流体相。②熔体中氟含量大于约1 wt%后，D Sn小于0.1且变化不大，当液相富含HCl且熔体中氟含量从约1 wt%降低后，D Sn 迅速增大，即熔体中氟含量小于约1 wt%后锡倾向于分配进入富氯的酸性流体中。而富氟（F含量大于约1 wt%）的熔体有利于萃取锡并使锡在熔体相中富集。③熔体铝饱和指数ASI值越大，相应锡的分配系数越大；流体相中HCl浓度增大时，锡分配系数随之增大；当熔体为过铝质的花岗质熔体、流体富含HCl时有利于锡分配进入流体相。 分析总结与花岗岩有关的锡成矿特征和锡在不同晶体相和熔体相间的分配行为得出：壳源铝质、富碱、富挥发份、贫钙铁镁的岩浆在结晶分异演化过程中相对有利于锡在残余熔流体相中富集。因此，具有这些特征的岩浆结晶分异演化产生的晚期岩浆可富含锡，能为后期锡矿床的形成提供矿质来源。这种富锡富挥发份的岩浆在上侵过程中，当温度压力降低、岩浆水饱和度增大、硅含量增大、熔体相氟含量降低时，可分异出含氯富锡的成矿流体。 根据上述结论，分析了与湖南芙蓉锡矿床有着密切成因联系的骑田岭花岗岩的岩石化学特征、成岩成矿物理化学条件，得出芙蓉锡矿床成矿流体可由骑田岭晚期岩浆分异产生。 最后得出如下认识：1)当花岗质岩浆体系水不饱和、流体相络阴离子浓度低的情况下，锡倾向于分配进入熔体相中；2)水饱和富含挥发份的过铝、富钾的岩浆体系有利于锡分配进入流体相；3) 铝质、富钾、富挥发份的富碱侵入岩岩浆演化过程中可在有利的物理化学条件下分异出富锡的流体相，与芙蓉超大型锡矿床有成因联系的骑田岭富碱侵入岩体成岩过程中可分异出富锡的成矿流体。

贵州喀斯特高原湖泊物质循环过程中的铜锌同位素地球化学－以红枫湖、阿哈湖为例

近年来铜、锌同位素地球化学研究已经进入了快速发展时期。作为新兴的同位素技术手段，铜锌同位素工具已普遍应用于地球化学、矿床学、古海洋学和生物学等多种领域，然而铜、锌同位素在湖泊生态系统中的研究却相对较少。湖泊生态系统中，重金属的迁移、循环与转化一直是地球科学家们关注的焦点，但研究手段仅局限于含量与形态的测定。因此本论文旨在通过对湖泊生态系统中铜、锌同位素的研究，揭示影响铜、锌同位素组成的主要因素，为铜、锌同位素成为湖泊系统中新的重金属示踪工具奠定基础。 本论文通过一系列条件实验，确定了用于MC-ICP-MS测定环境样品中铜、锌同位素时最佳的化学分离条件。随后选取红枫湖和阿哈湖为主要研究对象，用此实验流程对湖泊水体及其主要支流悬浮物中的铜、锌同位素的季节及剖面变化进行了初步研究。除此之外，对水体中重金属如Cu、Zn、Mn、Ni、Co、Cr、Cd和Pb的形态分布特征及物质循环进行了研究。主要得出以下几点认识： 1、环境样品中铜锌的最佳分离条件是，采用AG MP-1(100-200目)阴离子交换树脂，分别以7 mol/L HCl + 0.001% H2O2，2 mol/L HCl+ 0.001% H2O2，0.5 mol/L HNO3作为淋洗液，并分别在适当的体积接收淋洗液，可以有效地分离沉积物、植物和悬浮物等样品中的铜和锌。化学分离过程中回收率接近100％，同位素比值的变化均在误差范围以内。 2、红枫湖、阿哈湖水体及主要支流悬浮物和红枫湖生物样品中的δ65Cu分布范围为-2.64‰~1.11‰，可达到3.75‰的变化。红枫湖夏季水体悬浮物的δ65Cu变化为-0.08‰~0.25‰，入湖河流水体悬浮物δ65Cu的变化范围为0.13‰~ 1.11‰；阿哈湖夏季水体悬浮物δ65Cu的变化范围为-0.62‰~0.37‰，入湖河流水体悬浮物δ65Cu的变化范围为-1.08‰~0.60‰。两湖冬季水体悬浮物的δ65Cu值均较负。红枫湖生物样品中δ65Cu较负（-1.54‰~ 0.03‰）。 红枫湖水体悬浮物中δ65Cu的随水深的变化趋势主要受到藻类吸收作用的控制，而阿哈湖δ65Cu的随水深的变化趋势主要受到其物源的控制。说明在贫营养化湖泊中，铜同位素组成可以示踪物源；而在富营养化湖泊中，铜同位素组成则可以示踪生物活动。同时水温的垂直变化也可能是其影响因素之一。 3、红枫湖水体及其主要支流水体悬浮物中的δ66Zn变化范围分别为-0.29‰~0.26‰和-0.04‰~0.48‰，阿哈湖水体及其主要支流水体悬浮物中的δ66Zn变化范围分别为-0.18‰~0.27‰和-0.17‰~0.46‰，均表现出支流中的锌同位素组成较重的趋势。而生物样品中的δ66Zn变化范围较大，为-0.35‰~0.57‰。说明湖泊生态系统中各端元的锌同位素组成存在明显差异。 红枫湖夏季δ66Zn随着湖水深度的变化，与Chla（叶绿素）呈极显著的正相关(R=0.97)。说明锌同位素组成与藻类生物量有一定的响应关系，主要是藻类对锌的有机吸附或是吸收过程改变了锌同位素组成。阿哈湖的锌同位素组成主要受到其源区的控制作用，从而可利用锌同位素示踪源区；此外，红枫湖和阿哈湖悬浮物中的锌同位素比值均表现出夏季小于冬季，说明大气的干湿沉降可能是一个较负的锌同位素源。生物样品中的δ66Zn变化范围较大，说明由于生物作用过程导致的锌同位素分馏大于非生物过程。 4、红枫湖重金属Mn、Ni、Co、Cr、Cd和Pb的含量在南湖高于北湖，主要是羊昌湖的输入所导致；重金属入湖通量的季节性变化，直接导致了重金属含量的季节性变化。沉积物－水界面在冬夏季节，由于“富氧”和“贫氧”状态的改变，导致了溶解态Mn、Ni和Cr的季节性变化；水粒相互作用过程中，溶解有机碳（DOC）、氧化铁胶体、氧化锰胶体和水生藻类的生长繁殖，影响了重金属不同结合形态的变化。

湖北恩施表生高硒环境中有机结合态硒的形态研究

硒是人体和动物必需的微量元素，摄入过高或过低均可导致不同的健康效应。已有的研究表明，硒的生物有效性不仅与地质环境中的总硒有关，更取决于硒的形态分布。不同形态的硒具有显著差异的地球化学特性，影响着环境中硒的迁移、循环、生物有效性和毒性。渔塘坝是中国唯一发生过人群硒中毒爆发性流行的地区，该地区风化富硒碳质岩和高硒土壤中有机结合态硒可达到总硒的60%以上，而有机结合态硒的进一步研究有助于深入了解硒的分布和生物可利用性，阐明富硒碳质岩风化及其成土过程中硒的生物地球化学次生富集过程与循环机制。本论文利用改进的7步连续化学浸提技术和优化的有机结合态硒提取方案，使用氢化物发生－原子荧光光谱法，研究了恩施表生高硒环境中有机结合态硒的形态分布，得出了以下几点结论： 1. 在硒七步连续提取方案的基础上，对影响硒提取的因素如液固比、提取剂浓度等进行了优化、并对不同结合态（相态）硒提取中的若干问题进行了讨论。研究结果表明，硒的连续化学提取过程中，液固比为20:1到50:1时能够满足不同结合态硒提取的要求；在水浴加热条件下，NaOH浓度0.1M～0.5M时能有效提取有机结合态硒；1M Na2SO3溶液是元素硒的较好提取剂；而对于硫化物/硒化物结合态硒，合适配比的NaOH＋H2O2混合液有利于H2Se的完全吸收，500～600mL/min的载气气流能保证其被CrCl2+HCl混合液还原所产生H2Se气体的完全吸收。 2. 利用优化的连续化学浸提方案提取风化富硒碳质岩石和高硒土壤样品的有机结合态硒，进而分离出富里酸硒和胡敏酸硒，并用高压密闭消化－氢化物原子荧光光谱法测定了硒的含量。该方案的回收率为84.4～104.2%，平均回收率为96.1%；有机结合态硒与胡敏酸富里酸硒加和值之间有良好的一致性，线性相关系数为0.999（n＝14），斜率为1.0026。而后使用自制的氢化物反应发生和吸收装置进一步分离了与富里酸（胡敏酸）吸附的Se(IV)和强结合的硒，其中分离富里酸硒的回收率为86.3%～107.6%，平均值为97.1%；分离胡敏酸硒的回收率为85.5%～105.9%，平均值为97.9%。表明本论文所采用的实验方案是切实可行的。 3. 风化富硒碳质岩石样品中胡敏酸硒比例较高，所占比例为36.3%～75.8%，平均值为58.1%，但胡敏酸硒并不是占有绝对的优势，且各个样品之间存在较大差异。高硒土壤样品中富里酸硒占有机结合态比例在25.4%～85.0%，除个别样品外，多数样品的富里酸硒所占比例均在70%～80%，表明富里酸硒是渔塘坝土壤有机结合态硒的一种主要存在形式，在适当的条件下（如环境的pH-Eh变化），能够被转化从而被植物吸收利用。并且这种岩石中胡敏酸硒含量高、土壤中富里酸硒含量高的分布特征指示了硒在风化过程中可能的迁移和转化规律。 4. 富里酸硒和胡敏酸硒的形态分析表明，不同岩石样品中各有机结合态硒的形态分布差异较大，分布规律不明显，这可能与岩石样品的风化程度有关；而对于土壤样品，不论是在富里酸还是胡敏酸中，吸附Se(IV)的含量都大于强结合硒，尤其是富里酸中的吸附Se(IV)，平均值为83.4%，最高达95.4%。这部分吸附的Se(IV)相对于强结合的富里酸硒更容易被释放，而这也进一步佐证了富里酸硒易于受环境变化（pH-Eh）和倍半氧化物等的影响而转变为生物可利用态硒。 5. 无论是胡敏酸强结合硒（HA-Se）还是富里酸强结合硒（FA-Se）均在有机结合态硒中以一定的比例存在，对这部分硒的研究还仅局限于定量，而其究竟是以何种形态、以何种方式与腐殖质结合尚不清楚。因此，有必要对这部分硒进行进一步研究。

湖泊沉积物碳氧同位素和介形虫Li/Ca比值与古环境重建

了解过去是认识现在和预测未来的基础。晚全新世是PAGES研究的目标时段之一。寻找和解译最近2000年连续、高分辨率自然记录是古气候研究的热点与难点。本项研究有针对性地选择程海、草海和青海湖开展湖泊沉积物环境记录的精细研究，结合14C、210Pb和137Cs定年，系统探讨了碳酸盐碳氧同位素、纤维素碳氧同位素、有机质碳同位素以及介形虫壳体Li/Ca比值指标的古环境指示意义。 通过研究，本论文取得了如下成果和新的认识： 1. 建立了一套有效的四阶段湖泊沉积物有机质纤维素提取方法（5%NaOH碱洗、5%HCl酸洗、亚氯酸钠和冰醋酸混合溶液漂白以及17.5%NaOH碱洗），红外光谱鉴定提取物为纯的α-纤维素，表明该实验方法是可行的，为今后广泛开展湖泊沉积物纤维素稳定同位素研究打下了坚实基础。 2. 多指标综合辨识了程海和草海沉积物碳酸盐主要是自生碳酸盐。程海和草海沉积物有机质C/N比值结合有机质碳同位素结果表明两湖的有机质分别源于水生植物藻类和大型水草。程海和草海沉积物碳酸盐含量主要反映了湖区温度的变化。 3. 程海、草海沉积物碳酸盐与青海湖沉积物介形虫壳体氧同位素组成均反映了湖区降水/蒸发比。降水/蒸发比大的湿润期，碳酸盐δ18O值小；降水/蒸发比小的干旱期，碳酸盐δ18O值大。程海沉积物碳酸盐碳同位素组成影响因素复杂，除了受大气与湖水之间的CO2交换影响外，还受水生植物光合/吸收作用的影响；草海沉积物碳酸盐碳同位素组成更大的变化范围，反映了湖区水生植物光合/吸收作用的影响，其异常的正值可能指示了湖区细菌参与有机质碳同位素分馏过程。 4. 利用草海沉积物有机质纤维素氧同位素定量恢复了湖水氧同位素组成变化。在此基础上，结合碳酸盐氧同位素组成初步恢复了草海地区过去500年来温度变化历史：草海地区在过去500年明显存在四个冷期，包括1550－1610年，1670－1730年，1770－1870年和1890－1920年冷期，其中前三个发生在传统意义上的现代小冰期时段。与其它记录研究结果的一致性表明纤维素氧同位素结合碳酸盐氧同位素是恢复古温度变化的最有效途径之一，同时也为现代小冰期在中国西南地区的存在提供了湖泊沉积学方面的证据。 5. 不同类型水生植物湖泊，湖泊沉积物有机质δ13C值对湖泊初级生产力变化的响应过程不同。大型水草为主的湖泊（草海），其沉积物有机质δ13C值随湖泊生产力的增大呈现增加的变化趋势；藻类为主的湖泊（程海），其沉积物有机质δ13C随湖泊生产力的增大呈现减小的变化趋势，藻类易降解是导致δ13C值随湖泊生产力的增大呈现减小变化趋势的主要原因。 6. 程海沉积物碳酸盐和有机质碳同位素组成的正相关变化以及草海沉积物碳酸盐和有机质碳同位素组成的负相关变化.表明湖泊生产力变化并不是导致碳酸盐和有机质碳同位素正相关变化的主要原因，湖泊水生植物类型以及湖泊大小均起着重要作用。湖泊沉积物碳酸盐与有机质之间的碳同位素分馏（△δ13C）是一种有效的湖泊生产力指示剂，即使是在有微生物参与有机质碳同位素分馏过程的草海，△δ13C值也反映了湖泊生产力的变化过程。 7. 青海湖沉积物单一种属介形虫壳体胖真星介（Eucypris inflata）Li/Ca比值与气象记录以及邻近地区都兰和祁连山树轮宽度指数恢复的古温度变化序列的对比研究揭示，介形虫壳体Li/Ca比值与温度呈明显的负相关变化（Li/Ca比值高，温度低；Li/Ca比值低，温度高），表明介形虫壳体Li/Ca比值是一种有效的古温度代用指标。 8. 青海湖沉积物单一种属介形虫壳体胖真星介（Eucypris inflata）Li/Ca比值、氧同位素与反映太阳活动的大气14C含量和冰芯10Be含量的一致性变化表明青海湖地区温度和降雨量的同步变化主要受太阳活动控制。

Determination of alcohols by high-performance liquid chromatography with fluorimetric detection after pre-column derivatisation with carbazole-9-N-acetic acid and chromatographic behaviour of alcoholic derivatives

Alcohols were derivatised to their carbazole-9-N-acetic acid (CRA) esters with 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride (EDC . HCl) as the dehydrating agent. Studies on derivatisation conditions indicated that the coupling reaction proceeded rapidly and smoothly in the presence of a base catalyst in acetonitrile to give the corresponding sensitively fluorescent derivatives. The retention behaviour of alcohol derivatives was investigated by varying mobile phase compositions (ACN-water and MeOH-water). The parameters from the equation log k'=A-BX were evaluated by retention data of derivatives using an isocratic elution with different mobile phases. The results indicated that the parameters derived allowed computation of retention factors in good agreement with experiments. At the same time, a general equation was derived that makes possible predictions of partition coefficient in binary mobile phases with different proportions of organic solvent to water based on some simple regression analysis. The LC separation for the derivatised alcohols containing higher carbon alcohols showed good reproducibility on a reversed-phase C-18 column with gradient elution. The detection limits (excitation at 335 nm, emission at 360 nm) for derivatised alcohols (signal-to-noise ratio=3:1) were in the range of 0.1-0.4 pg per injection. (C) 2001 Elsevier Science B.V. All rights reserved.

Otimização de protocolo para análise de AFLP em Lolium multiflorum Lam.

ESTABELECIMENTO DE METODOLOGIA PARA ANÁLISE MOLECULAR DE AZEVÉM ANUAL COM MARCADORES AFLP. O uso de marcadores moleculares no manejo de bancos de germoplasma tem sido cada vez mais expressivo. Entre os diferentes tipos de marcadores moleculares, o AFLP, Amplified Fragment Length Polymorphism, apresenta algumas vantagens para uso na caracterização de recursos genéticos, como a detecção de grande número de bandas informativas por reação, com ampla cobertura do genoma e considerável reprodutibilidade, além de não necessitar de dados de seqüenciamento prévio da espécie para a construção de primers. Embora a análise de AFLP seja freqüentemente utilizada em estudos de variabilidade genética em diferentes espécies, o uso da técnica em Lolium multiflorum ainda é incipiente. Com a finalidade de estabelecer um protocolo para o emprego da técnica de AFLP em azevém anual foi conduzido este trabalho. Foram avaliadas as concentrações iniciais de DNA genômico de 100 e 250 ng, a digestão do DNA com 1,25 e 1U das enzimas EcoRI e MSe, e os respectivos tempos de reação de digestão: 3, 6 e 12 horas. Também foram avaliadas quatro concentrações da solução resultante da ligação dos adaptadores: solução sem diluição; diluída 1:5; 1:10 e 1:20 e duas diluições após a reação de pré-amplificação, de 1:25 e 1:50. Como resultado, foi estabelecido como melhor protocolo, no qual foi obtido um maior número e qualidade de fragmentos, o que utiliza a concentração inicial de DNA genômico de 100 ng, num volume final de reação de digestão 10 ?l, com 1U de cada enzima EcoRI e MseI e tempo de reação de 12h a 37°C, com reação de ligação de adaptadores realizada com a adição da solução de ligação de adaptadores, do Kit AFLP? Analysis System I (InvitroGen Life Technologies, Carlsbad, Calif., USA), e 0,4 U de T4 DNA ligase em um volume final de 10?l, por 2h a 20°C. Após a ligação de adaptadores a diluição deverá ser de 1:5. A reação de pré-amplificação deverá ocorrer a partir de 1?l desta última solução (diluída 1:5), 1,0 X PCR buffer com Mg Plus [Tris-HCl (pH 7.6) 20 mM, MgCl2 1,5 mM, KCl 50 mM], BSA 0,003% e 1 U de Taq DNA polimerase, completando com mix de pré-amplificação do Kit AFLP? Analysis System I até alcançar o volume final de 11?l. O produto da pré-amplificação deverá ser diluído 1:25 antes de ser procedida à amplificação seletiva, a qual deve ser realizada utilizando 2,5 ?l da solução de DNA pré-amplificado (diluído 1:25), 1 X PCR buffer com Mg Plus [Tris-HCl (pH 8,4) 20 mM, MgCl2 1,5 mM, KCl 50 mM], BSA (0,003%), 1 U de Taq DNA polimerase, 10 ng de primer EcoRI, 1,5 ng de primer MseI, 0,4mM de DNTps e H2O MilliQ? até completar o volume final de 10?l. Com este protocolo uma única combinação de primers permitiu identificar 58 bandas polimórficas na análise de duas populações de azevém anual.

New route for light olefins production from chloromethane over HSAPO-34 molecular sieve

HSAPO-34 molecular sieve was employed in chloromethane conversion and showed high performance in activity and selectivity in production of light olefins. Our detailed IR investigation allowed the identification of the active sites and the adsorbed species and demonstrated that the conversion started from 350 degrees C with alkoxy group as the intermediate. The fixed-bed catalytic testing evidenced that in the range of 350-500 degrees C, 70-80% of chloromethane was transferred to ethylene, propylene and butenes. Increasing reaction temperature favors the conversion and enhances the yield of lighter olefins. A very important reversible phenomenon, the breaking of Al-O-P bonds upon adsorption of HCl, a main product of reaction to generate a large amount of P-OH groups and the recovery of Al-O-P upon removal of HCI was revealed. (c) 2005 Elsevier B.V. All rights reserved.

Synteza i struktura nowych aminowych analogów ansamycynowego antybiotyku rifampicyny

Wydział Chemii: Zakład Biochemii

Zmiany właściwości włóknistych krzemianów pod wpływem czynników fizykochemicznych

Wydział Chemii

Application of mesoporous silica for the oral delivery of poorly water-soluble drugs

The objective of this thesis was to improve the dissolution rate of the poorly waters-soluble drug, fenofibrate by processing it with a high surface area carrier, mesoporous silica. The subsequent properties of the drug – silica composite were studied in terms of drug distribution within the silica matrix, solid state and release properties. Prior to commencing any experimental work, the properties of unprocessed mesoporous silica and fenofibrate were characterised (chapter 3), this allowed for comparison with the processed samples studied in later chapters. Fenofibrate was a highly stable, crystalline drug that did not adsorb moisture, even under long term accelerated storage conditions. It maintained its crystallinity even after SC-CO2 processing. Its dissolution rate was limited and dependent on the characteristics of the particular in vitro media studied. Mesoporous silica had a large surface area and mesopore volume and readily picked up moisture when stored under long term accelerated storage conditions (75% RH, 40 oC). It maintained its mesopore character after SC-CO2 processing. A variety of methods were employed to process fenofibrate with mesoporous silica including physical mixing, melt method, solvent impregnation and novel methods such as liquid and supercritical carbon dioxide (SC-CO2) (chapter 4). It was found that it was important to break down the fenofibrate particulate structure to a molecular state to enable drug molecules enter into the silica mesopores. While all processing methods led to some increase in fenofibrate release properties; the impregnation, liquid and SC-CO2 methods produced the most rapid release rates. SC-CO2 processing was further studied with a view to optimising the processing parameters to achieve the highest drug-loading efficiency possible (chapter 5). In this thesis, it was that SC-CO2 processing pressure had a bearing on drug-loading efficiency. Neither pressure, duration or depressurisation rate affected drug solid state or release properties. The amount of drug that could be loaded onto to the mesoporous silica successfully was also investigated at different ratios of drug mass to silica surface area under constant SC-CO2 conditions; as the drug – silica ratio increased, the drug-loading efficiency decreased, while there was no effect on drug solid state or release properties. The influence of the number of drug-loading steps was investigated (chapter 6) with a view to increasing the drug-loading efficiency. This multiple step approach did not yield an increase in drug-loading efficiency compared to the single step approach. It was also an objective in this chapter to understand how much drug could be loaded into silica mesopores; a method based on the known volume of the mesopores and true density of drug was investigated. However, this approach led to serious repercussions in terms of the subsequent solid state nature of the drug and its release performance; there was significant drug crystallinity and reduced release extent. The impact of in vitro release media on fenofibrate release was also studied (chapter 6). Here it was seen that media containing HCl led to reduced drug release over time compared to equivalent media not containing HCl. The key findings of this thesis are discussed in chapter 7 and included: 1. Drug – silica processing method strongly influenced drug distribution within the silica matrix, drug solid state and release. 2. The silica surface area and mesopore volume also influenced how much drug could be loaded. It was shown that SC-CO2 processing variables such as processing pressure (13.79 – 41.37 MPa), duration time (4 – 24 h) and depressurisation rate (rapid or controlled) did not influence the drug distribution within the SBA- 15 matrix, drug solid state form or release. Possible avenues of research to be considered going forward include the development and application of high resolution imaging techniques to visualise drug molecules within the silica mesopores. Also, the issues surrounding SBA-15 usage in a pharmaceutical manufacturing environment should be addressed.

On the adsorption of hexaammineruthenium (III) at anionic self-assembled monolayers

The binding of the electroactive hexaammineruthenium (III) complex ions to anionic self-assembled monolayers (SAMs) has been investigated by means of chronocoulometry and ac voltammetry. From chronocoulometric data recorded in 10-2 M LiClO4 containing different [Ru(NH3)6]3+ concentrations, we have established the adsorption isotherm of [Ru(NH3)6]3+ on a compact monolayer of 2-mercaptobenzimidazole-5-sulfonate (MBIS) self-assembled on Au(1 1 1). The data were satisfactorily fitted to the linearized Langmuir adsorption isotherm and a binding constant of 4.0 (±0.4) × 106 M-1 has been determined. The electrostatic binding of [Ru(NH3)6]3+ to a dilute PNA-DNA monolayer formed after hybridization on a PNA-modified gold electrode by self-assembly from a mixed solution of mercaptobutan-1-ol and PNA oligonucleotides has been studied by ac voltammetry. The admittance of the PNA-modified electrode after hybridization with complementary DNA was measured in 0.01 M Tris-HCl buffer containing different [Ru(NH3)6]3+ concentrations. Based on these data, a binding constant of [Ru(NH3)6]3+ to the surface-confined PNA-DNA duplex was derived from the Langmuir isotherm and amounts to 2.9 (±0.3) × 105 M-1. As the interactions between [Ru(NH3)6]3+ and the immobilized PNA-DNA hybrids on the gold surface are essentially electrostatic, the adsorption of the highly charged cationic redox complex at low concentrations to the negatively charged PNA-DNA modified surface is in large competition with other monovalent cations present in the electrolyte at higher concentrations. The influence of competing sodium cations was thus studied by adding different NaCl concentrations in the 0.01 M Tris-HCl electrolyte. © 2008 Elsevier Ltd. All rights reserved.

Four-decade responses of soil trace elements to an aggrading old-field forest: B, Mn, Zn, Cu, and Fe.

In the ancient and acidic Ultisol soils of the Southern Piedmont, USA, we studied changes in trace element biogeochemistry over four decades, a period during which formerly cultivated cotton fields were planted with pine seedlings that grew into mature forest stands. In 16 permanent plots, we estimated 40-year accumulations of trace elements in forest biomass and O horizons (between 1957 and 1997), and changes in bioavailable soil fractions indexed by extractions of 0.05 mol/L HCl and 0.2 mol/L acid ammonium oxalate (AAO). Element accumulations in 40-year tree biomass plus O horizons totaled 0.9, 2.9, 4.8, 49.6, and 501.3 kg/ha for Cu, B, Zn, Mn, and Fe, respectively. In response to this forest development, samples of the upper 0.6-m of mineral soil archived in 1962 and 1997 followed one of three patterns. (1) Extractable B and Mn were significantly depleted, by -4.1 and -57.7 kg/ha with AAO, depletions comparable to accumulations in biomass plus O horizons, 2.9 and 49.6 kg/ha, respectively. Tree uptake of B and Mn from mineral soil greatly outpaced resupplies from atmospheric deposition, mineral weathering, and deep-root uptake. (2) Extractable Zn and Cu changed little during forest growth, indicating that nutrient resupplies kept pace with accumulations by the aggrading forest. (3) Oxalate-extractable Fe increased substantially during forest growth, by 275.8 kg/ha, about 10-fold more than accumulations in tree biomass (28.7 kg/ha). The large increases in AAO-extractable Fe in surficial 0.35-m mineral soils were accompanied by substantial accretions of Fe in the forest's O horizon, by 473 kg/ha, amounts that dwarfed inputs via litterfall and canopy throughfall, indicating that forest Fe cycling is qualitatively different from that of other macro- and micronutrients. Bioturbation of surficial forest soil layers cannot account for these fractions and transformations of Fe, and we hypothesize that the secondary forest's large inputs of organic additions over four decades has fundamentally altered soil Fe oxides, potentially altering the bioavailability and retention of macro- and micronutrients, contaminants, and organic matter itself. The wide range of responses among the ecosystem's trace elements illustrates the great dynamics of the soil system over time scales of decades.

Elucidating the Molecular Composition of Cartilage by Proteomics.

Articular cartilage consists of chondrocytes and two major components, a collagen-rich framework and highly abundant proteoglycans. Most prior studies defining the zonal distribution of cartilage have extracted proteins with guanidine-HCl. However, an unextracted collagen-rich residual is left after extraction. In addition, the high abundance of anionic polysaccharide molecules extracted from cartilage adversely affects the chromatographic separation. In this study, we established a method for removing chondrocytes from cartilage sections with minimal extracellular matrix protein loss. The addition of surfactant to guanidine-HCl extraction buffer improved protein solubility. Ultrafiltration removed interference from polysaccharides and salts. Almost four-times more collagen peptides were extracted by the in situ trypsin digestion method. However, as expected, proteoglycans were more abundant within the guanidine-HCl extraction. These different methods were used to extract cartilage sections from different cartilage layers (superficial, intermediate, and deep), joint types (knee and hip), and disease states (healthy and osteoarthritic), and the extractions were evaluated by quantitative and qualitative proteomic analyses. The results of this study led to the identifications of the potential biomarkers of osteoarthritis (OA), OA progression, and the joint specific biomarkers.