Ecological impact of Mahshahr petrochemical activities on abundance and diversity of macrobenthic fauna in Zangi Creek (Persian Gulf)

The Moosa Creek extends from its opening into the Persian Gulf, with some sub narrow creeks leading to it. Zangi creek is one of the main branches of Moosa creek. The creek contains numerous sources of organic pollution, including sewage outlet flows and boat waste. After establishing the Petrochemical special Economic Zone (PETZONE) in 1997 near to the Zangi Creek, the pipelines, streets and railway made it distinct from eastern and western parts of this creek. Industrial activities have released sludge and effluents in this creek along these years. A survey of the Zangi creek was performed, assessing water properties, organic pollution, and the population density, distribution and diversity of macrobenthic fauna through bi-monthly sampling from July 2006 to September 2007. Samples were collected from water near the bottom and sediment at 7 stations include 2 stations inside the distinct Zangi creek and 4 stations along a transect with 1 km distances between them in eastern free part and one reference station located at the Persian Gulf entrance to the Moosa creek. The environmental parameters such as temperature, salinity, pH, dissolved oxygen, COD, turbidity, EC and heavy metals include Hg, Cd, Pb, Ni as well as percentage silt-clay and total organic matter of the sediment were measured. The faunal population density and their distribution are discussed in relation to the environmental changes. Results showed spatial heterogeneity in faunal distribution of the Zangi creek. Nine groups of macrofauna were identified out of distinct zangi creek. Polychaets formed the dominant group (48%) followed by bivalves (13%), gastropods (10%), Decapods (2%), Tanaids (5%), and all other groups (22%). The distinct creek was heavily polluted without any macrofauna communities probably as a consequence of the high pH, COD, low salinity and heavy metals contamination specially Cd and Pb. The other stations near to the disposal site were found with macrofauna communities commonly tolerant to organic pollution, At 3 km east of the disposal site, macrofauna is comparable to the surrounded creek, whereas macrofauna still indicate environmental degradation. Farther a way, faunal density decreases and equilibrium taxa gradually replace opportunistic species, while the other stations were far from polluted area contained lower pollution and relatively healthy macrofauna. The mean biomass of macrobenthic fauna were estimated for the whole studied area. The results are considered in Minimum density and biomass in surrounded creek and maximum density and biomass in 3 km of surrounded area. Biodiversity Indices were low in surrounded creek. The Shanon-weaver information index was used to describe the spatially variations in diversity. Macrofauna density, shanon and simpson index were significantly variable between surrounded and free parts of Zangi creek (p<0.05). The numerical abundance of macrobenthose varied from 221. m-2 in polluted area to 4346 m-2 in free part of Zangi creek. The Shanon-weaver information index varied from 0.4 in distinct area to 2.9 in reference station. The physico- chemical changes between distinct and free creeks showed significant variations such as pH, salinity and EC. Salinity and EC were significantly positive correlate to macrofauna density, whereas pH and TOM percentage indicated significantly negative correlation to density. Heavy metals concentrations in sediments were higher than water samples. Concentration pattern of heavy metals in sediments and water samples were Ni>Pb>Cd>Hg. Salinity and pH were significantly correlated to metals in sediments (p<0.01). No significant correlation were found between Macrofauna density and heavy metals (p<0.05).

Development of zona-free hamster ova to blastocysts in vitro

The zona pellucida (ZP) enclosing the mammalian ovum is important for its protection and for initial stages of fertilization, but the role of the ZP during embryo development is less clear. This study was designed to investigate if the hamster ZP is needed for embryo development from 1-cell to blastocyst in vitro, and to compare methods for removing the ZP. A total of 395 hamster pronucleate ova were collected 10 h post activation from superovulated, mated female hamsters. The ZP was removed from some ova using either 0.05% pronase, 0.05% trypsin or acid Tyrode's solution. To prevent ZP-free ova from sticking together, they were cultured singly in 30-50 muL drops of HECM-6 culture medium together with ZP-intact ova as controls. There was no significant difference among treatment groups in embryo development to blastocyst: 36/87 (42%) in the ZP intact group; 35/75 (47%) in the pronase-treated ZP-free group; 37/74 (50%) in the trypsin-treated ZP-free group; and 37/71 (52%) in the acid-treated ZP-free group. These results indicate that 1) the ZP is unnecessary for hamster embryo development in vitro from the pronucleate ovum stage to blastocyst; 2) none of the three ZP-removal methods was detrimental to embryo development; 3) embryos do not need to be cultured in groups during in vitro development from 1-cell to blastocyst. (C) 2000 by Elsevier Science Inc.

Molecular docking and 3D-QSAR study of pyranmycin derivatives against 16S rRNA A site

To understand pharmacophore properties of pyranmycin derivatives and to design novel inhibitors of 16S rRNA A site, comparative molecular field analysis (CoMFA) approach was applied to analyze three-dimensional quantitative structure-activity relationship (3D-QSAR) of 17 compounds. AutoDock 3.0.5 program was employed to locate the orientations and conformations of the inhibitors interacting with 16S rRNA A site. The interaction mode was demonstrated in the aspects of inhibitor conformation, hydrogen bonding and electrostatic interaction. Similar binding conformations of these inhibitors and good correlations between the calculated binding free energies and experimental biological activities suggest that the binding conformations of these inhibitors derived from docking procedure were reasonable. Robust and predictive 3D-QSAR model was obtained by CoMFA with q(2) values of 0.723 and 0.993 for cross-validated and noncross-validated, respectively. The 3D-QSAR model built here will provide clear guidelines for novel inhibitors design based on the Pyranmycin derivatives against 16S rRNA A site. (c) 2005 Elsevier B.V. All rights reserved.

Model-based influences on humans' choices and striatal prediction errors.

The mesostriatal dopamine system is prominently implicated in model-free reinforcement learning, with fMRI BOLD signals in ventral striatum notably covarying with model-free prediction errors. However, latent learning and devaluation studies show that behavior also shows hallmarks of model-based planning, and the interaction between model-based and model-free values, prediction errors, and preferences is underexplored. We designed a multistep decision task in which model-based and model-free influences on human choice behavior could be distinguished. By showing that choices reflected both influences we could then test the purity of the ventral striatal BOLD signal as a model-free report. Contrary to expectations, the signal reflected both model-free and model-based predictions in proportions matching those that best explained choice behavior. These results challenge the notion of a separate model-free learner and suggest a more integrated computational architecture for high-level human decision-making.

Development of tolerance against toxic Microcystis aeruginosa in three cladocerans and the ecological implications

This is the first experimental study to compare difference in the development of tolerance against toxic Microcystis among multi-species of cladocerans (Daphnia, Moina and Ceriodaphnia) pre-exposed to two M. aeruginosa PCC7820 strains (MC-containing and MC-free). Zooplankton were divided into S population (fed Scenedesmus), M-F population (fed Scenedesmus + MC-free Microcystis), and M-C population (fed Scenedesmus + MC-containing Microcystis). M-F and M-C populations were pre-exposed to Microcystis strains for 4 weeks, and their newborns were collected for experiments. A pre-exposure to MC-containing or MC-free Microcystis increased tolerance against toxic Microcystis. The marked increases in survival rate and median lethal time (LT50, 100-194% increase) in the M-C population of Ceriodaphnia suggest that small-sized cladocerans may develop stronger tolerance against Microcystis than large-sized ones when both groups are exposed to toxic Microcystis. This may explain why dominant Daphnia is usually replaced by small-sized cladocerans when cyanobacteria bloomed in summer in eutrophic lakes. (c) 2005 Elsevier Ltd. All rights reserved.

A new phototransistor with uni-travelling-carrier and optically gradual coupling properties

Based on appropriate combination of different band-gap InGaAsP, a new edge-coupled two-terminal double heterojunction phototransistor (ECTT-DHPT) was designed and fabricated, which is double heterojunction, free-aluminium, and works under uni-travelling-carrier mode and optically gradual coupling mode. This device is fully compatible with monolithic micro-wave integrated circuits (MMIC) and heterojunction bipolar transistor (HBT) in material and process. The DC characteristics reveal that the new ECTT-DHPT can perform good optoelectronic mix operation and linear amplification operation by optically biased at two appropriate value respectively. Responsivity of more than 52 A/W and dark current of 70 nA (when V-EC = 1 V) were obtained.

Electrical and optical coupling in an electroabsorption modulator integrated with a DFB laser

Electrical and optical coupling in an electroabsorption (EA) modulator integrated with a distributed feedback (DFB) laser have been investigated. The integrated device is treated as a three-port optoelectronic device with two electrical ports and one optical output port. The scattering parameters of this three-port device have been measured in the designed experiment. The measured results indicate that there exists the electrical coupling between the DFB laser and EA modulator of the integrated light source whenever the current applied to the laser section is below or above the threshold current, and the optical coupling will have stronger influence on the frequency responses than the electrical coupling when the bias current is above the threshold. A small-signal equivalent circuit model for the integrated device is established considering both the electrical and internal optical coupling. Experiments show that the equivalent circuit model is reasonable and the determined element values are correct. Based on the measurement and modeling, the influences of the electrical and optical coupling on the high-frequency responses are investigated and the effective measure to eliminate the additional modulation in the DFB laser are discussed.

Structural, photoluminescence, and field emission properties of vertically well-aligned ZnO nanorod arrays

The self-assembled growth of vertically well-aligned ZnO nanorod arrays with uniform length and diameter on Si substrate has been demonstrated via thermal evaporation and vapor-phase transport. The structural, photoluminescence (PL), and field emission properties of the as-prepared nanorod arrays were investigated. The PL spectrum at 10 K shows a strong and sharp near-band gap emission (NBE) peak ( full width at half-maximum (FWHM) = 4.7 meV) and a weak neglectable deep-level emission (DL) peak (I-NBE/I-DL= 220), which implies its good crystallinity and high optical quality. The room-temperature NBE peak was deduced to the composition of free exciton and its first-order replicas emissions by temperature-dependent PL spectra. The field emission measurements indicate that, with a vacuum gap of 400 Am, the turn-on field and threshold field is as low as 2.3 and 4.2 V/mu m. The field enhancement factor beta and vacuum gap d follows a universal equation.

Two opposite gradients of hole density in as-grown and annealed (Ga,Mn)As layers

The depth distribution of the hole density p in 500 nm-thick (Ga,Mn)As layers is investigated. From Raman scattering spectra, it is found that the gradients of p are opposite in the as-grown and annealed layers. At the region around the free surface, with increasing etching depth, p significantly increases in the as-grown layer; however, p decreases distinctly in the annealed layer. Then, in the bulk, p becomes almost homogeneous for both cases. The etching-depth dependence of Curie temperature obtained from magnetic measurements is in agreement with the distribution characterization of p. These results suggest that annealing induces outdiffusion of Mn interstitials towards the free surface, and incomplete outdiffusion during the growth leads to an accumulation of Mn interstitials around the free surface of the as-grown (Ga,Mn)As. (c) 2006 Elsevier B.V. All rights reserved.

High-power AlGaInP laser diodes with current-injection-free region near the laser facet

A high-power AlGaInP laser diode with current-injection-free region near the facet is successfully fabricated by metaorganic chemical vapor deposition (MOCVD) using the (100) direction n-GaAs substrates with a misorientation of 15 deg toward the (011) direction. The maximum continuous wave output power is about 90 mW for the traditional structure. In comparison, the maximum output power is enhanced by about 67%, and achieves 150 mW for LDs with current-infection-free regions. The fundamental transverse-mode operation is obtained up to 70 mW. Output characteristics at high temperatures are also improved greatly for an LD with a current-injection-free region, and the highest operation temperature is 70 C at 50 mW without kink. The threshold current is about 33 mA, the operation current and the slope efficiency at 100 mW are 120 mA and 0.9 mW/mA, respectively. The lasing wavelength is 658.4 nm at room-temperature 50 mW. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

High responsivity ultraviolet photodetector based on crack-free GaN on Si (111)

A Schottky-based metal-semiconductor-metal photodetector is fabricated on 1 mu m-thick, crack-free GaN on Si (I 11) substrate using an optimized AlxGal-xN/AlN complex buffer layer. It exhibits a high responsivity of 4600A/W at 366nm which may be due to both a crack-free sample and high internal gain. The relationship between responsivity and bias voltage is also investigated. The experiment results indicate that the responsivity increases with the bias voltage and shows a tendency to saturate. (c) 2007 WILEY-VCH Verlag GmbH &Co. KGaA, Weinheim.

Determination of photochemically produced hydroxyl radicals in seawater and freshwater

A variety of short-lived, reactive chemical species (i.e. free radicals and excited state species) are known to be photochemically produced in natural waters. Some of these transients may strongly affect chemical and biological processes, and they have been implicated in the degradation of organic pollutants and natural organic compounds in aqueous environments. Previous studies demonstrated that the highly reactive hydroxyl radical (OH) is photochemically formed in seawater. However, the quantitative importance of this key species in the sea has not been previously studied because of past analytical limitations. By using a highly sensitive probe based on α-H atom abstraction from methanol, we were able to measure production rates and steady-state concentrations of photochemically produced OH radicals in coastal and open ocean seawater and freshwaters. The validity of the method was tested by intercalibrating with an independent, OH-specific reaction, hydroxylation of benzoic acid, and also by competition kinetics experiments. Our OH production rates and steady-state concentrations for freshwaters are in excellent agreement with those measured by previous investigators for similar waters. In contrast, for seawater, the values we measured are 1–3 orders of magnitude higher than previously predicted by models, indicating that there is a major unknown photochemical OH source (s) in seawater.

PLLA-PCys co-electrospun fibers for capture and elution of glutathione S-transferase

The copolymer poly(L-lactic acid)-b-poly(L-cysteine) (PLA-b-PCys) was co-electrospun with PLGA into ultrafine fibers. The reduced glutathione (GSH) was conjugated to the fiber surfaces via disulfide bonds. The glutathione S-transferase (GST) was captured onto the GSH fibers via specific substrate-enzyme interaction between the bound GSH and GST. The captured GST was eluted with free GSH aqueous solution and lyophilized to get pure GST powders. The results show that the GSH moieties on the fiber surface retain the bioactivity of the free GSH and thus they can bind specifically with GST and the GST in solution is captured onto the fiber surface. In addition, the bound GSH is not as active as free GSH so that the captured GST can be eluted off from the fiber by free GSH aqueous solution. Based on this principle, GST itself or its fused proteins can be separated and purified very easily. The preliminary purification efficiency is 6.5 mg center dot(g(PCys))(-1). Further improvements are undertaken.

Hole nucleation and growth induced by crystallization and microphase separation of thin semicrystalline diblock copolymer films

We have investigated the hole nucleation and growth induced by crystallization of thin crystalline-coil diblock copolymer films. Semicrystalline rodlike assemblies from neutral/selective binary solvent are used as seeds to nucleate crystallization at temperatures above the glass transition temperature (T-g) but below melting point (T-m). The crystallization of nanorods drives neighboring copolymer chains to diffuse into the growing nanorods. Depletion of copolymer chains yields hole nucleation and growth at the edge of the nanorods. Simultaneously, the polymer chains unassociated into the nanorods were oriented by induction from the free surface and the substrate, leading to limitation of the hole depth to the lamellar spacing, similar to20 nm. The holes, as well as the nanorods, grow as t(alpha), where t is the annealing time and a crossover in the exponent a. is found. The orientation and stretching of the copolymer chains by the surface and interface are believed to accelerate the crystallization, and in turn, the latter accelerates the growth rate of the holes. At T > T-m, the grains melt and the copolymer chains relax and flow into the first layer of the film.

Isothermal and nonisothermal crystallization kinetics of nylon-46

Isothermal and nonisothermal crystallization kinetics of nylon-46 were investigated with differential scanning calorimetry. The equilibrium melting enthalpy and the equilibrium melting temperature of nylon-46 were determined to be 155.58 J/g and 307.10 degreesC, respectively. The isothermal crystallization process was described by the Avrami equation. The lateral surface free energy and the end surface free energy of nylon-46 were calculated to be 8.28 and 138.54 erg/cm(2), respectively. The work of chain folding was determined to be 7.12 kcal/mol. The activation energies were determined to be 568.25 and 337.80 kJ/mol for isothermal and nonisothermal crystallization, respectively. A convenient method was applied to describe the nonisothermal crystallization kinetics of nylon-46 by a combination of the Avrami and Ozawa equations.