Network virtualisation from an operator perspective

Network virtualisation is seen as a promising approach to overcome the so-called “Internet impasse” and bring innovation back into the Internet, by allowing easier migration towards novel networking approaches as well as the coexistence of complementary network architectures on a shared infrastructure in a commercial context. Recently, the interest from the operators and mainstream industry in network virtualisation has grown quite significantly, as the potential benefits of virtualisation became clearer, both from an economical and an operational point of view. In the beginning, the concept has been mainly a research topic and has been materialized in small-scale testbeds and research network environments. This PhD Thesis aims to provide the network operator with a set of mechanisms and algorithms capable of managing and controlling virtual networks. To this end, we propose a framework that aims to allocate, monitor and control virtual resources in a centralized and efficient manner. In order to analyse the performance of the framework, we performed the implementation and evaluation on a small-scale testbed. To enable the operator to make an efficient allocation, in real-time, and on-demand, of virtual networks onto the substrate network, it is proposed a heuristic algorithm to perform the virtual network mapping. For the network operator to obtain the highest profit of the physical network, it is also proposed a mathematical formulation that aims to maximize the number of allocated virtual networks onto the physical network. Since the power consumption of the physical network is very significant in the operating costs, it is important to make the allocation of virtual networks in fewer physical resources and onto physical resources already active. To address this challenge, we propose a mathematical formulation that aims to minimize the energy consumption of the physical network without affecting the efficiency of the allocation of virtual networks. To minimize fragmentation of the physical network while increasing the revenue of the operator, it is extended the initial formulation to contemplate the re-optimization of previously mapped virtual networks, so that the operator has a better use of its physical infrastructure. It is also necessary to address the migration of virtual networks, either for reasons of load balancing or for reasons of imminent failure of physical resources, without affecting the proper functioning of the virtual network. To this end, we propose a method based on cloning techniques to perform the migration of virtual networks across the physical infrastructure, transparently, and without affecting the virtual network. In order to assess the resilience of virtual networks to physical network failures, while obtaining the optimal solution for the migration of virtual networks in case of imminent failure of physical resources, the mathematical formulation is extended to minimize the number of nodes migrated and the relocation of virtual links. In comparison with our optimization proposals, we found out that existing heuristics for mapping virtual networks have a poor performance. We also found that it is possible to minimize the energy consumption without penalizing the efficient allocation. By applying the re-optimization on the virtual networks, it has been shown that it is possible to obtain more free resources as well as having the physical resources better balanced. Finally, it was shown that virtual networks are quite resilient to failures on the physical network.

Analysis of the organic matter associated to sea salt : definition of potential molecular markers based on the volatile composition and presence of glycosidic derivatives and polysaccharides

Sea salt is a natural product obtained from the evaporation of seawater in saltpans due to the combined effect of wind and sunlight. Nowadays, there is a growing interest for protection and re-valorisation of saltpans intrinsically associated to the quality of sea salt that can be evaluated by its physico-chemical properties. These man-made systems can be located in different geographical areas presenting different environmental surroundings. During the crystallization process, organic compounds coming from these surroundings can be incorporated into sea salt crystals, influencing their final composition. The organic matter associated to sea salt arises from three main sources: algae, surrounding bacterial community, and anthropogenic activity. Based on the hypothesis that sea salt contains associated organic compounds that can be used as markers of the product, including saltpans surrounding environment, the aim of this PhD thesis was to identify these compounds. With this purpose, this work comprised: 1) a deep characterisation of the volatile composition of sea salt by headspace solid phase microextraction combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (HS-SPME/GCGC–ToFMS) methodology, in search of potential sea salt volatile markers; 2) the development of a methodology to isolate the polymeric material potentially present in sea salt, in amounts that allow its characterisation in terms of polysaccharides and protein; and 3) to explore the possible presence of triacylglycerides. The high chromatographic resolution and sensitivity of GC×GC–ToFMS enabled the separation and identification of a higher number of volatile compounds from sea salt, about three folds, compared to unidimentional chromatography (GC–qMS). The chromatographic contour plots obtained revealed the complexity of marine salt volatile composition and confirmed the relevance of GC×GC–ToFMS for this type of analysis. The structured bidimentional chromatographic profile arising from 1D volatility and 2D polarity was demonstrated, allowing more reliable identifications. Results obtained for analysis of salt from two locations in Aveiro and harvested over three years suggest the loss of volatile compounds along the time of storage of the salt. From Atlantic Ocean salts of seven different geographical origins, all produced in 2007, it was possible to identify a sub-set of ten compounds present in all salts, namely 6-methyl-5-hepten-2-one, 2,2,6-trimethylcyclohexanone, isophorone, ketoisophorone, β-ionone-5,6-epoxide, dihydroactinidiolide, 6,10,14-trimethyl-2-pentadecanone, 3-hydroxy-2,4,4-trimethylpentyl 2-methylpropanoate, 2,4,4-trimethylpentane-1,3-diyl bis(2-methylpropanoate), and 2-ethyl-1-hexanol. These ten compounds were considered potential volatile markers of sea salt. Seven of these compounds are carotenoid-derived compounds, and the other three may result from the integration of compounds from anthropogenic activity as metabolites of marine organisms. The present PhD work also allowed the isolation and characterisation, for the first time, of polymeric material from sea salt, using 16 Atlantic Ocean salts. A dialysis-based methodology was developed to isolate the polymeric material from sea salt in amounts that allowed its characterisation. The median content of polymeric material isolated from the 16 salts was 144 mg per kg of salt, e.g. 0.014% (w/w). Mid-infrared spectroscopy and thermogravimetry revealed the main occurrence of sulfated polysaccharides, as well as the presence of protein in the polymeric material from sea salt. Sea salt polysaccharides were found to be rich in uronic acid residues (21 mol%), glucose (18), galactose (16), and fucose (13). Sulfate content represented a median of 45 mol%, being the median content of sulfated polysaccharides 461 mg/g of polymeric material, which accounted for 66 mg/kg of dry salt. Glycosidic linkage composition indicates that the main sugar residues that could carry one or more sulfate groups were identified as fucose and galactose. This fact allowed to infer that the polysaccharides from sea salt arise mainly from algae, due to their abundance and composition. The amino acid profile of the polymeric material from the 16 Atlantic Ocean salts showed as main residues, as medians, alanine (25 mol%), leucine (14), and valine (14), which are hydrophobic, being the median protein content 35 mg/g, i.e. 4,9 mg per kg of dry salt. Beside the occurrence of hydrophobic volatile compounds in sea salt, hydrophobic non-volatile compounds were also detected. Triacylglycerides were obtained from sea salt by soxhlet extraction with n-hexane. Fatty acid composition revealed palmitic acid as the major residue (43 mol%), followed by stearic (13), linolenic (13), oleic (12), and linoleic (9). Sea salt triacylglycerides median content was 1.5 mg per kg of dry salt. Both protein and triacylglycerides seem to arise from macro and microalgae, phytoplankton and cyanobacteria, due to their abundance and composition. Despite the variability resulting from saltpans surrounding environment, this PhD thesis allowed the identification of a sea salt characteristic organic compounds profile based on volatile compounds, polysaccharides, protein, and triacylglycerides.

Síntese e transformações de compostos do tipo pirazol e 1,2,3-triazol

Compostos do tipo pirazol e 1,2,3-triazol encontram-se presentes em inúmeras moléculas biologicamente ativas. Muitos fármacos atualmente comercializados ou em fase de estudos clínicos contêm na sua estrutura base núcleos de pirazol ou 1,2,3-triazol. Por isso, estes compostos têm sido alvo de intensa pesquisa na procura de novas moléculas com potenciais aplicações medicinais e agroquímicas. Nesta dissertação são descritas novas vias de síntese de novos compostos do tipo pirazol e 1,2,3-triazol. No primeiro capítulo apresenta-se uma breve revisão bibliográfica sobre a atividade biológica, ocorrência natural e métodos de síntese de pirazóis e seus derivados. O segundo capítulo foca-se na síntese de (E)-2-estiril-3-halo-4H-cromen-4-onas e sua transformação em 3(5)-aril-5(3)-[2-(2-hidroxifenil)-2-oxoetil-1H-pirazóis. Em primeiro lugar faz-se uma revisão bibliográfica sobre as (E)-2-estiril-4H-cromen-4-onas e a sua semelhança estrutural com as flavonas, a sua importância e ocorrência natural e métodos de síntese. São ainda abordadas as metodologias mais utilizadas para a síntese de derivados halogenados de (E)-2-estiril-4H-cromen-4-onas. Seguidamente são apresentados e discutidos os resultados da síntese de (E)-3-bromo-2-estiril-4H-cromen-4-onas através da reação de 5-aril-3-hidroxi-1-(2-hidroxifenil)penta-2,4-dien-1-onas com NBS, sob irradiação com micro-ondas, tendo sido estabelecida uma nova metodologia mais eficiente, rápida e regiosseletiva para a síntese de (E)-3-bromo-2-estiril-4H-cromen-4-onas, na ausência de solvente. São igualmente apresentados os resultados da síntese regiosseletiva de (E)-2-estiril-3-iodo-4H-cromen-4-onas através da reação de 5-aril-3-hidroxi-1-(2-hidroxifenil)penta-2,4-dien-1-onas com NIS e TFA/TFAA/NaOAc. Em ambos os métodos de halogenação desenvolvidos, obtiveram-se como produtos secundários as (E)-2-estiril-4H-cromen-4-onas correspondentes. Seguidamente é apresentado o estudo da reação de (E)-2-estiril-3-halo-4H-cromen-4-onas com hidrato de hidrazina. Ao contrário do esperado, obtiveram-se os 3(5)-aril-5(3)-[2-(2-hidroxifenil)-2-oxoetil-1H-pirazóis através de uma reação de adição conjugada 1,6-, de hidrazina à posição C- da cromona com consequente abertura do anel, seguida de uma adição conjugada 1,4- intramolecular. Estes resultados demonstraram que esta reação segue um mecanismo diferente daquele que está reportado na literatura para a reação de (E)-2-estiril-4H-cromen-4-onas não halogenadas em C-3 com hidrato de hidrazina. No terceiro capítulo apresenta-se uma breve revisão bibliográfica sobre as propriedades, aplicações e metodologias de síntese de 1,2,3-triazóis, dando mais relevância às reações de cicloadição 1,3-dipolar e de “click-chemistry”. Seguidamente descrevem-se os resultados obtidos na reação de (E)-5(3)-estiril-3(5)-(2-hidroxifenil)-1H-pirazóis com a azida de sódio para obtenção de díades pirazol-1,2,3-triazol. No entanto esta reação deu origem a novos 5(3)-(2-aril-2-azidoetil)-3(5)-(2-hidroxifenil)-1H-pirazóis e não às díades pirazol-1,2,3-triazol pretendidas. Como o resultado não foi o esperado, desenvolveu-se outra metodologia de síntese, que envolve, num primeiro, a reação de (E)-2-estiril-4H-cromen-4-onas com azida de sódio, dando origem a 5(4)-aril-4(5)-(cromon-2-il)-1H-1,2,3-triazóis. No passo seguinte, efetuou-se a reação destes compostos com hidrato de hidrazina tendo ocorrido a formação das diades 5(4)-aril-4(5)-[3(5)-(2-hidroxifenil)-1H-pirazol-5(3)-il]-1H-1,2,3-triazol pretendidas. No quarto capítulo, estudou-se a reatividade de (E)-5(3)-estiril-3(5)-(2-hidroxifenil)-1H-pirazóis em reações de iodação com vista à obtenção de 4-iodo-1H-pirazóis. Apresenta-se uma breve revisão bibliográfica sobre os diferentes métodos descritos na literatura para a iodação de compostos heterocíclicos aromáticos, nomeadamente para a obtenção de 4-iodo-1H-pirazóis. Dos vários sistemas de iodação testados, o sistema oxidativo I2/CAN foi o que deu melhores resultados na iodação dos (E)-5(3)-estiril-3(5)-(2-hidroxifenil)-1H-pirazóis. Este método permitiu iodar a posição C-4 do núcleo de pirazol apenas para os derivados que possuem o grupo nitro ou o átomo de cloro no anel do grupo estirilo, obtendo-se o 3(5)-(2-hidroxifenil)-4-iodo-5(3)-(4-nitrofenil)vinil-1H-pirazol e o 5(3)-(4-clorofenil)vinil)-3(5)-(2-hidroxi-5-iodofenil)-4-iodo-1H-pirazol; no entanto, para os restantes derivados, verificou-se apenas a iodação nas posições ativadas do anel fenólico. Todos os novos compostos sintetizados foram caraterizados estruturalmente recorrendo a estudos de espetroscopia de ressonância magnética nuclear (RMN) mono e bidimensionais. Sempre que possível, para uma caraterização estrutural mais completa, foram efetuados espetros de massa (EM) e análises elementares ou espetros de massa de alta resolução (EMAR) para todos os novos compostos sintetizados. Finalmente são apresentadas as conclusões gerais deste trabalho e perspetivas futuras.

Identificação de utilizadores seniores em televisão interativa (iTV) : uma matriz de decisão tecnológica

Desde que surgiu há mais de 50 anos, a televisão sofreu muitas transformações, tanto ao nível tecnológico (por exemplo com a passagem da emissão a preto/branco para cor, o som analógico para digital, a difusão digital) como a nível da sua influência nas sociedades. Entre outros fatores de ordem tecnológica, a consolidação da Internet com o seu elevado nível de personalização, da experiência de utilização, e a sua enorme quantidade de conteúdos disponíveis, catapultou a televisão no sentido de esta se tornar mais interativa. Assim, o telespectador passou a poder usufruir de uma experiência televisiva que pode, por um lado, ser mais participativa, sendo-lhe possível, por exemplo, alvitrar sobre a qualidade de um programa enquanto assiste à sua exibição, e, por outro, ser mais personalizada, possibilitando-lhe, por exemplo, receber conteúdos automaticamente adequados ao seu perfil e contexto. No entanto, esta experiência mais participativa e personalizável carece de uma identificação, idealmente automática e não intrusiva, de quem pode beneficiar da mesma – o telespectador. Contudo, e apesar de significativos avanços na área da televisão interativa, tanto ao nível da infraestrutura de suporte como ao nível dos serviços disponibilizados, a identificação dos utilizadores é, ainda, uma área de estudo com muitos aspetos por compreender. Os seniores, em particular, são grandes consumidores de televisão e representam uma fatia muito considerável das pessoas que podem beneficiar das potencialidades disponibilizadas pela interatividade presente em muitos serviços atuais. Um número crescente destes serviços são desenhados com o objetivo de promoverem um envelhecimento ativo e um concreto apoio à vida, pelo que os seniores podem beneficiar, em vários aspetos do seu quotidiano, se os utilizarem. Nesta faixa etária, a identificação de utilizadores tem, como elemento potenciador da experiência de utilização, um papel especialmente importante ao nível de um aproveitamento personalizado e dirigido destes serviços. No entanto, atendendo às diferentes combinações de características físicas, sensoriais, cognitivas e, mesmo, de literacia digital que tipificam os seniores, perspetivou-se existir uma dependência do perfil do utilizador na seleção do método de identificação mais adequado, os quais podem ser baseados, por exemplo, num leitor de impressões digitais, instalado no telecomando; na leitura de uma wearable tag ou de um cartão RFiD; no reconhecimento da face e, eventualmente, na voz do utilizador. Assim, a inerente investigação desenrolou-se em várias fases, no sentido de permitir alicerçar a construção de uma matriz de decisão tecnológica que, em função do perfil de utilizador, selecione o sistema de identificação mais adequado. O procedimento metodológico inerente à construção desta matriz de decisão, passou por um longo processo envolvendo utilizadores reais, que se iniciou com a realização de entrevistas exploratórias com o objetivo de permitir conhecer melhor os seniores e a forma como estes encaram a tecnologia e, mais concretamente, a televisão interativa. Foi depois implementado um protótipo de alta-fidelidade, completamente funcional, para a realização de testes com o objetivo de perceber qual a preferência relativamente a um subconjunto de tecnologias de identificação. Estes testes, uma vez que não permitiram testar todas as tecnologias em estudo, revelaram-se inconclusivos, porém permitiram reforçar a necessidade de identificar e caracterizar os referidos aspetos do perfil do utilizador que podem interferir na sua preferência relativamente ao sistema de identificação. As características identificadas constituíram-se como os parâmetros de entrada da matriz, sendo que para preencher as respetivas células realizaramse testes de aceitação, com um conjunto de seniores, tendo por base um protótipo, wizard of oz, especificamente implementado para permitir experienciar todas as tecnologias em estudo. Estes testes foram precedidos pela avaliação das capacidades funcionais dos participantes, nos diversos parâmetros definidos. Este texto relata, assim, todo o processo de investigação que foi conduzido, terminando com uma descrição de exemplos de utilização da matriz de decisão implementada e com a identificação de potenciais caminhos de desenvolvimento deste trabalho.

Interactions of cetaceans with Spanish and Portuguese fisheries in Atlantic waters : costs, benefits and implications for management

With the aim to provide new insights into operational cetacean-fishery interactions in Atlantic waters, this thesis assesses interactions of cetaceans with Spanish and Portuguese fishing vessels operating in Iberian and South West Atlantic waters. Different opportunistic research methodologies were applied, including an interview survey with fishers (mainly skippers) and onboard observations by fisheries observers and skippers, to describe different types of interactions and to identify potential hotspots for cetacean-fishery interactions and the cetacean species most involved, and to quantify the extent and the consequences of these interactions in terms of benefits and costs for cetaceans and fisheries. In addition, the suitability of different mitigation strategies was evaluated and discussed. The results of this work indicate that cetaceans interact frequently with Spanish and Portuguese fishing vessels, sometimes in a beneficial way (e.g. cetaceans indicate fish schools in purse seine fisheries), but mostly with negative consequences (depredation on catch, gear damage and cetacean bycatch). Significant economic loss and high bycatch rates are, however, only reported for certain fisheries and associated with particular cetacean species. In Galician fisheries, substantial economic loss was reported as a result of bottlenose dolphins damaging artisanal coastal gillnets, while high catch loss may arise from common dolphins scattering fish in purse seine fisheries. High cetacean bycatch mortality arises in trawl fisheries, mainly of common dolphin and particularly during trawling in water depths below 350 m, and in coastal set gillnet fisheries (mainly common and bottlenose dolphins). In large-scale bottom-set longline fisheries in South West Atlantic waters, sperm whales may significantly reduce catch rates through depredation on catch. The high diversity of cetacean-fishery interactions observed in the study area indicates that case-specific management strategies are needed to reduce negative impacts on fisheries and cetaceans. Acoustic deterrent devices (pingers) may be used to prevent small cetaceans from approaching and getting entangled in purse seines and set gillnets, although possible problems include cetacean habituation to the pinger sounds, as well as negative side effects on non-target cetaceans (habitat exclusion) and fisheries target species (reduced catch rates). For sardine and horse mackerel, target species of Iberian Atlantic fisheries, no aversive reaction to pinger sounds was detected during tank experiments conducted in the scope of this thesis. Bycatch in trawls may be reduced by the implementation of time/area restrictions of fishing activity. In addition, the avoidance of fishing areas with high cetacean abundance combined with the minimization of fishery-specific sound cues that possibly attract cetaceans, may also help to decrease interactions. In large-scale bottom-set longline fisheries, cetacean depredation on catch may be reduced by covering hooked fish with net sleeves ("umbrellas") provided that catch rates are not negatively affected by this gear modification. Trap fishing, as an alternative fishing method to bottom-set gillnetting and longlining, also has the potential to reduce cetacean bycatch and depredation, given that fish catch rates are similar to the rates obtained by bottom-set gillnets and longlines, whereas cetacean by-catch is unlikely. Economic incentives, such as the eco-certification of dolphin-safe fishing methods, should be promoted in order to create an additional source of income for fishers negatively affected by interactions with cetaceans, which, in turn, may also increase fishers’ willingness to accept and adopt mitigation measures. Although the opportunistic sampling methods applied in this work have certain restrictions concerning their reliability and precision, the results are consistent with previous studies in the same area. Moreover, they allow for the active participation of fishers that can provide important complementary ecological and technical knowledge required for cetacean management and conservation.

Brazilian savanna forest : conservation, medicinal reservoir and bioprospecting

This study aimed to analyse the Brazilian savanna forest from a Legal Reserve (LR) area from a perspective of conservation, reservoir of organic carbon and medicinal biomass for a prospective use of native medicinal plants. An ethnobotanical and ethnopharmacological survey was carried out close to a community settled in the rural area in the south of Tocantins, being selected 9 of the most cited species (cajuí- Anacardium othonianum; inharé-Brosimum gaudichaudii; jatobá-Hymenaeae courbaril; jenipapo-Genipa americana, aroeira-Myracrodruon urundeuva; negramina-Siparuna guianensis; barbatimão- Stryphnodendron obovatum; assa peixe-Vernonia brasiliana, embaúba-Cecropia pachystachya). Crude foliar extracts were subjected to a preliminary phytochemical prospection and triage of secondary metabolites with antimicrobial activity of potential interest in health and familiar agriculture. Phenolic compounds, terpenes and flavonoids were detected in the extracts of most species, which suggests the presence of antimicrobial, antioxidant and anti-insect activities. It was evident the need to better know the LR as a reservoir of medicinal biomass in an area under ecological tension where 35% (610ha) of the property is LR and should be protected by law. Therefore, a forest inventory of live woody species was performed using the allometric or indirect method. This identified a rare remnant of Semidecidual Seasonal Forest amidst the largest world savannah, the Cerrado biome. An analysis of the forest average productivity per basal area (m².ha), aerial live biomass (ton.ha-1) and carbon stock was carried out. The forest fragment was considered relatively rich in species and diversity, although showing signs of disturbance and dominance by a few species. Its horizontal structure suggests biotic regeneration conditions. It is an important reservoir of medicinal plants. Of the families (57.5%) presenting medicinal species, 19 from a total of 33 are represented in the area and contain 44% (27) of the total species (61) and 63% (432) of the total individuals catalogued. Medicinal species have ecological importance for the equilibrium of the local flora and represent 80% of the 10 species with higher Importance Value Index (IVI): Tetragastris altissima, Chrysophyllum marginatum, Oenocarpus distichus, Sclerolobium paniculatum, Simarouba versicolor, Alibertia macrophylla, Siparuna guianensis, Maprounea guianensis, Licania parvifolia e Physocalymma scaberrimum. Medicinal productivity was high for this type of phytophysionomy: 183,2 ton. ha-1 of biomass and 91,51 ton. ha-1 of carbon representing 66% of the total biomass and carbon of this Cerrado forest. From this stage S. guianensis (Siparunaceae) was selected for performing bioassays in order to verify its biological activity against microorganisms of health and agricultural relevance. This is a native aromatic medicinal plant recommended as priority for conservation, with local popular medicinal validation and availability of medicinal feedstock (3300 Kg.ha-1), with the foliar fraction giving 38Kg/ha of crude extract and 5L/ha of essential oil. Foliar crude extracts and essential oil were obtained and tested in vitro using a disk diffusion bioassay. Different concentrations of these natural products were tested against gram-positive bacteria (Staphylococcus aureus ATCC 29213), gram-negative bacteria (Escherichia coli ATCC 25922 and ATCC 35218; Pseudomonas aeruginosa ATCC 10145) and fungi (Candida albicans ATCC 6258 e Fusarium oxysporum). The essential oil inhibited the growth of S. aureus in its crude concentration (380μg.mL-1), as well as diluted to half (190μg.mL-1) and a quarter strength (95μg.mL-1). It’s likely that such action is due to sesquiterpenes major components, such as bisabolol and bisabolene (10.35%), measured by gas chromatography (GC-MS, GC-FID). Extracts did not exhibit any antimicrobial activity against the microorganisms tested. The native medicinal plants prospective market is an alternative that favours the conservation of biodiversity while generating benefits for the development of sustainable family productive activities within local ecosystems instead of the current inappropriate uses. This strengthens conservation policies of Legal Reserve in rural settlements and is in agreement with public policy on global warming and climate changes.

Thick-microstructures for MPGDs: simulations and experimental studies

Cherenkov Imaging counters require large photosensitive areas, capable of single photon detection, operating at stable high gains under radioactive backgrounds while standing high rates, providing a fast response and a good time resolution, and being insensitive to magnetic fields. The development of photon detectors based in Micro Pattern Gaseous detectors (MPGDs), represent a new generation of gaseous photon detectors. In particular, gaseous detectors based on stacked Thick-Gaseous Electron Multipliers (THGEMs), or THGEM based structures, coupled to a CsI photoconverter coating, seem to fulfil the requirements imposed by Cherenkov imaging counters. This work focus on the study of the THGEM-based detectors response as function of its geometrical parameters and applied voltages and electric fields, aiming a future upgrade of the Cherenkov Imaging counter RICH-1 of the COMPASS experiment at CERN SPS. Further studies to decrease the fraction of ions that reach the photocathode (Ion Back Flow – IBF) to minimize the ageing and maximize the photoelectron extraction are performed. Experimental studies are complemented with simulation results, also perfomed in this work.

Ecology and conservation of felids in the Brazilian pantanal

Habitat conversion and environmental degradation have reached alarming levels in the Pantanal, endangering all its biodiversity. This scenario is complicated by the fact that the biome relies on only a few protected areas, which combined do not exceed 10% of the territory. Felids, as predators, play a vital role in the maintenance of this ecosystem, but require large areas, have low population densities and, typically, are very sensitive to environmental disturbances. Amolar Mountain Ridge is considered an area of extreme importance and high priority for conservation within the biome. There are four species of felids in this region: the jaguar (Panthera onca), the puma (Puma concolor), the ocelot (Leopardus pardalis), and jaguarundi (Puma yagouaroundi). However, little is known about the ecology of these species in this region or the magnitude of interaction between the communities living around the protected areas and the animals. The goal of this study was to increase our knowledge about these felids and understand how people interact with them in order to contribute to their conservation in the network of parks within Amolar. Camera trapping surveys were carried out in two areas of the network, covering approximately 83,000 hectares, in order to identify the species of mammals occurring in the region, those that may be potential prey for the felids, and to obtain basic ecological data about both felids and prey. In addition, we conducted surveys in three riverside schools in order to assess the knowledge, perceptions and attitudes of schoolchildren regarding the four focal felids, and surveys among the adult population to assess their perceptions and attitudes towards the jaguar. We recorded a total of 33 species of mammals from both study areas. The large cats were cathemeral, reflecting the temporal activity of larger prey, whereas the ocelot was nocturnal, mirroring the activity of smaller prey. Jaguar occupancy was influenced by prey abundance, while puma occupancy was influenced by patch density in drier dense forest. Jaguars and pumas may be competitors over temporal and spatial scales, while no resource overlap was found for ocelots. Overall, both adults and children tended to have negative perceptions about the cats, which were related to the fear of being attacked. To increase awareness about the species and to maximize the effectiveness of protective measures in the network of reserves, it is recommended to develop and implement an Environmental Educational Program in the medium- to long-term in order to minimize the fear of these felids and to counsel locals on the role of felids in the maintenance of the Pantanal’s biodiversity.

Monte Carlo studies of phase transitions and adsorption : application to n-6 Lennard-Jones, C60 and zeolite systems

The solid-fluid transition properties of the n - 6 Lennard-Jones system are studied by means of extensive free energy calculations. Different values of the parameter n which regulates the steepness of the short-range repulsive interaction are investigated. Furthermore, the free energies of the n < 12 systems are calculated using the n = 12 system as a reference. The method relies on a generalization of the multiple histogram method that combines independent canonical ensemble simulations performed with different Hamiltonians and computes the free energy difference between them. The phase behavior of the fullerene C60 solid is studied by performing NPT simulations using atomistic models which treat each carbon in the molecule as a separate interaction site with additional bond charges. In particular, the transition from an orientationally frozen phase at low temperatures to one where the molecules are freely rotating at higher temperatures is studied as a function of applied pressure. The adsorption of molecular hydrogen in the zeolite NaA is investigated by means of grand-canonical Monte Carlo, in a wide range of temperatures and imposed gas pressures, and results are compared with available experimental data. A potential model is used that comprises three main interactions: van der Waals, Coulomb and induced polarization by the permanent electric field in the zeolite.

Materials and concepts for CO2 lean ironmaking by pyroelectrolysis

The main purpose of this PhD thesis was to provide convincing demonstration for a breakthrough concept of pyroelectrolysis at laboratory scale. One attempted to identify fundamental objections and/or the most critical constraints, to propose workable concepts for the overall process and for feasible electrodes, and to establish the main requirements on a clearer basis. The main effort was dedicated to studying suitable anode materials to be developed for large scale industrial units with molten silicate electrolyte. This concept relies on consumable anodes based on iron oxides, and a liquid Fe cathode, separated from the refractory materials by a freeze lining (solid) layer. In addition, one assessed an alternative concept of pyroelectrolysis with electron blocking membranes, and developed a prototype at small laboratory scale. The main composition of the molten electrolyte was based on a magnesium aluminosilicate composition, with minimum liquidus temperature, and with different additions of iron oxide. One studied the dynamics of devitrification of these melts, crystallization of iron oxides or other phases, and Fe2+/Fe3+ redox changes under laser zone melting, at different pulling rates. These studies were intended to provide guidelines for dissolution of raw materials (iron oxides) in the molten electrolyte, to assess compatibility with magnetite based consumable anodes, and to account for thermal gradients or insufficient thermal management in large scale cells. Several laboratory scale prototype cells were used to demonstrate the concept of pyroelectrolysis with electron blocking, and to identify the most critical issues and challenges. Operation with and without electron blocking provided useful information on transport properties of the molten electrolyte (i.e., ionic and electronic conductivities), their expected dependence on anodic and cathodic overpotentials, limitations in faradaic efficiency, and onset of side electrochemical reactions. The concept of consumable anodes was based on magnetite and derived spinel compositions, for their expected redox stability at high temperatures, even under oxidising conditions. Spinel compositions were designed for prospective gains in refractoriness and redox stability in wider ranges of conditions (T, pO2 and anodic overpotentials), without excessive penalty for electrical conductivity, thermomechanical stability or other requirements. Composition changes were also mainly based on components of the molten aluminosilicate melt, to avoid undue contamination and to minimize the dissolution rate of consumable anodes. Additional changes in composition were intended for prospective pyroelectrolysis of Fe alloys, with additions of different elements (Cr, Mn, Ni, Ti).

Organic contaminants in urban soils: major inputs and potential risks

Urban soil quality may be severely affected by hydrophobic organic contaminants (HOCs), impairing environmental quality and human health. A comprehensive study was conducted in two contrasting Portuguese urban areas (Lisbon and Viseu) in order to assess the levels and potential risks of these contaminants, to identify sources and study their behaviour in soils. The concentrations of HOCs were related to the size of the city, with much higher contamination levels observed in Lisbon urban area. Source apportionment was performed by studying the HOCs profiles, their relationship with potentially toxic elements and general characteristics of soil using multivariate statistical methods. Lisbon seems to be affected by nearby sources (traffic, industry and incineration processes) whereas in Viseu the atmospheric transport may be playing an important role. In a first tier of risk assessment (RA) it was possible to identify polycyclic aromatic hydrocarbons (PAHs) in Lisbon soils as a potential hazard. The levels of PAHs in street dusts were further studied and allowed to clarify that traffic, tire and pavement debris can be an important source of PAHs to urban soils. Street dusts were also identified as being a potential concern regarding human and environmental health, especially if reaching the nearby aquatic bodies. Geostatistical tools were also used and their usefulness in a RA analysis and urban planning was discussed. In order to obtain a more realistic assessment of risks of HOCs to environment and human health it is important to evaluate their available fraction, which is also the most accessible for organisms. Therefore, a review of the processes involved on the availability of PAHs was performed and the outputs produced by the different chemical methods were evaluated. The suitability of chemical methods to predict bioavailability of PAHs in dissimilar naturally contaminated soils has not been demonstrated, being especially difficult for high molecular weight compounds. No clear relationship between chemical and biological availability was found in this work. Yet, in spite of the very high total concentrations found in some Lisbon soils, both the water soluble fraction and the body residues resulting from bioaccumulation assays were generally very low, which may be due to aging phenomena. It was observed that the percentage of soluble fraction of PAHs in soils was found to be different among compounds and mostly regulated by soil properties. Regarding bioaccumulation assays, although no significant relationship was found between soil properties and bioavailability, it was verified that biota-to-soil bioaccumulation factors were sample dependent rather than compound dependent. In conclusion, once the compounds of potential concern are targeted, then performing a chemical screening as a first tier can be a simple and effective approach to start a RA. However, reliable data is still required to improve the existing models for risk characterization.

Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Seamless integration of heterogeneous networks in multicast environments

Nowadays, communication environments are already characterized by a myriad of competing and complementary technologies that aim to provide an ubiquitous connectivity service. Next Generation Networks need to hide this heterogeneity by providing a new abstraction level, while simultaneously be aware of the underlying technologies to deliver richer service experiences to the end-user. Moreover, the increasing interest for group-based multimedia services followed by their ever growing resource demands and network dynamics, has been boosting the research towards more scalable and exible network control approaches. The work developed in this Thesis enables such abstraction and exploits the prevailing heterogeneity in favor of a context-aware network management and adaptation. In this scope, we introduce a novel hierarchical control framework with self-management capabilities that enables the concept of Abstract Multiparty Trees (AMTs) to ease the control of multiparty content distribution throughout heterogeneous networks. A thorough evaluation of the proposed multiparty transport control framework was performed in the scope of this Thesis, assessing its bene ts in terms of network selection, delivery tree recon guration and resource savings. Moreover, we developed an analytical study to highlight the scalability of the AMT concept as well as its exibility in large scale networks and group sizes. To prove the feasibility and easy deployment characteristic of the proposed control framework, we implemented a proof-of-concept demonstrator that comprehends the main control procedures conceptually introduced. Its outcomes highlight a good performance of the multiparty content distribution tree control, including its local and global recon guration. In order to endow the AMT concept with the ability to guarantee the best service experience by the end-user, we integrate in the control framework two additional QoE enhancement approaches. The rst employs the concept of Network Coding to improve the robustness of the multiparty content delivery, aiming at mitigating the impact of possible packet losses in the end-user service perception. The second approach relies on a machine learning scheme to autonomously determine at each node the expected QoE towards a certain destination. This knowledge is then used by di erent QoE-aware network management schemes that, jointly, maximize the overall users' QoE. The performance and scalability of the control procedures developed, aided by the context and QoE-aware mechanisms, show the advantages of the AMT concept and the proposed hierarchical control strategy for the multiparty content distribution with enhanced service experience. Moreover we also prove the feasibility of the solution in a practical environment, and provide future research directions that bene t the evolved control framework and make it commercially feasible.

Extension of electrochemically active sites in SOFCs and SOECs

Solid oxide fuel (SOFCs) and electrolyzer (SOECs) cells have been promoted as promising technologies for the stabilization of fuel supply and usage in future green energy systems. SOFCs are devices that produce electricity by the oxidation of hydrogen or hydrocarbon fuels with high efficiency. Conversely, SOECs can offer the reverse reaction, where synthetic fuels can be generated by the input of renewable electricity. Due to this similar but inverse nature of SOFCs and SOECs, these devices have traditionally been constructed from comparable materials. Nonetheless, several limitations have hindered the entry of SOFCs and SOECs into the marketplace. One of the most debilitating is associated with chemical interreactions between cell components that can lead to poor longevities at high working temperatures and/or depleted electrochemcial performance. Normally such interreactions are countered by the introduction of thin, purely ionic conducting, buffer layers between the electrode and electrolyte interface. The objective of this thesis is to assess if possible improvements in electrode kinetics can also be obtained by modifying the transport properties of these buffer layers by the introduction of multivalent cations. The introduction of minor electronic conductivity in the surface of the electrolyte material has previously been shown to radically enhance the electrochemically active area for oxygen exchange, reducing polarization resistance losses. Hence, the current thesis aims to extend this knowledge to tailor a bi-functional buffer layer that can prevent chemical interreaction while also enhancing electrode kinetics.The thesis selects a typical scenario of an yttria stabilized zirconia electrolyte combined with a lanthanide containing oxygen electrode. Gadolinium, terbium and praseodymium doped cerium oxide materials have been investigated as potential buffer layers. The mixed ionic electronic conducting (MIEC) properties of the doped-cerium materials have been analyzed and collated. A detailed analysis is further presented of the impact of the buffer layers on the kinetics of the oxygen electrode in SOFC and SOEC devices. Special focus is made to assess for potential links between the transport properties of the buffer layer and subsequent electrode performance. The work also evaluates the electrochemical performance of different K2NiF4 structure cathodes deposited onto a peak performing Pr doped-cerium buffer layer, the influence of buffer layer thickness and the Pr content of the ceria buffer layer. It is shown that dramatic increases in electrode performance can be obtained by the introduction of MIEC buffer layers, where the best performances are shown to be offered by buffer layers of highest ambipolar conductivity. These buffer layers are also shown to continue to offer the bifunctional role to protect from unwanted chemical interactions at the electrode/electrolyte interface.

Decentralizing IP mobility management in future networks

The massive adoption of sophisticated mobile devices and applications led to the increase of mobile data in the last decade, which it is expected to continue. This increase of mobile data negatively impacts the network planning and dimension, since core networks are heavy centralized. Mobile operators are investigating atten network architectures that distribute the responsibility of providing connectivity and mobility, in order to improve the network scalability and performance. Moreover, service providers are moving the content servers closer to the user, in order to ensure high availability and performance of content delivery. Besides the e orts to overcome the explosion of mobile data, current mobility management models are heavy centralized to ensure reachability and session continuity to the users connected to the network. Nowadays, deployed architectures have a small number of centralized mobility anchors managing the mobile data and the mobility context of millions of users, which introduces issues related to performance and scalability that require costly network mechanisms. The mobility management needs to be rethought out-of-the box to cope with atten network architectures and distributed content servers closer to the user, which is the purpose of the work developed in this Thesis. The Thesis starts with a characterization of mobility management into well-de ned functional blocks, their interaction and potential grouping. The decentralized mobility management is studied through analytical models and simulations, in which di erent mobility approaches distinctly distribute the mobility management functionalities through the network. The outcome of this study showed that decentralized mobility management brings advantages. Hence, it was proposed a novel distributed and dynamic mobility management approach, which is exhaustively evaluated through analytical models, simulations and testbed experiments. The proposed approach is also integrated with seamless horizontal handover mechanisms, as well as evaluated in vehicular environments. The mobility mechanisms are also speci ed for multihomed scenarios, in order to provide data o oading with IP mobility from cellular to other access networks. In the pursuing of the optimized mobile routing path, a novel network-based strategy for localized mobility is addressed, in which a replication binding system is deployed in the mobility anchors distributed through the access routers and gateways. Finally, we go further in the mobility anchoring subject, presenting a context-aware adaptive IP mobility anchoring model that dynamically assigns the mobility anchors that provide the optimized routing path to a session, based on the user and network context. The integration of dynamic and distributed concepts in the mobility management, such as context-aware adaptive mobility anchoring and dynamic mobility support, allow the optimization of network resources and the improvement of user experience. The overall outcome demonstrates that decentralized mobility management is a promising direction, hence, its ideas should be taken into account by mobile operators in the deployment of future networks.