Discrete element modelling of power draw of tumbling mills

The power required to operate large mills is typically 5-10 MW. Hence, optimisation of power consumption will have a significant impact on overall economic performance and environmental impact. Power draw modelling results using the discrete element code PFC3D have been compared with results derived from the widely used empirical Model of Morrell. This is achieved by calculating the power draw for a range of operating conditions for constant mill size and fill factor using two modelling approaches. fThe discrete element modelling results show that, apart from density, selection of the appropriate material damping ratio is critical for the accuracy of modelling of the mill power draw. The relative insensitivity of the power draw to the material stiffness allows selection of moderate stiffness values, which result in acceptable computation time. The results obtained confirm that modelling of the power draw for a vertical slice of the mill, of thickness 20% of the mill length, is a reliable substitute for modelling the full mill. The power draw predictions from PFC3D show good agreement with those obtained using the empirical model. Due to its inherent flexibility, power draw modelling using PFC3D appears to be a viable and attractive alternative to empirical models where necessary code and computer power are available.

Critical comparison of Julius Kruttschnitt Mineral Research Centre (JKMRC) blast fragmentation models

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to Mill™ optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions - compressive and tensile. In the-first region, compressive stress waves form a 'crushed zone' directly adjacent to the blast hole. The second region, termed the 'cracked zone', occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to Mill™ project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the-fine to intermediate section (1-100 mm) of the fragmentation curve. This region of the distribution is important for Mine to Mill™ optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split . Following this work, an improved fragmentation model will be developed in response to these findings.

Effect of solute lipophilicity on penetration through canine skin

Objective To investigate the effect of lipophilicity on the percutaneous penetration of a homologous series of alcohols through canine skin Design Skin harvested from Greyhound thorax was placed in Franz-type diffusion cells and the in vitro passage of radio-labelled (C-14) alcohols (ethanol, butanol, hexanol and octanol (Log P 0.19 - 3.0)) through separate skin sections was measured in replicates of five. Permeability coefficient (k(P), cm/h), maximum flux (J(max), mol/cm(2)/h) and residue remaining within the skin were determined. Results The k(P) increased with increasing lipophilicity (6.2 x 10(-4) +/- 1.6 x 10(-4) cm/h for ethanol to 1.8 x 10(-2) 3.6 x 10(-3) cm/h for octanol). Alcohol residues remaining within each skin sample followed a similar pattern. An exponential decrease in Jmax with increasing lipophilicity was observed. Conclusion Changes in canine skin permeability occur with increasing alcohol lipophilicity. This finding has practical consequences for the design of topical formulations and optimisation of drug delivery through animal skin.

Scheduling of head-dependent cascaded reservoirs considering discharge ramping constraints and start/stop of units

This paper is on the problem of short-term hydro scheduling (STHS), particularly concerning head-dependent reservoirs under competitive environment. We propose a novel method, based on mixed-integer nonlinear programming (MINLP), for optimising power generation efficiency. This method considers hydroelectric power generation as a nonlinear function of water discharge and of the head. The main contribution of this paper is that discharge ramping constraints and start/stop of units are also considered, in order to obtain more realistic and feasible results. The proposed method has been applied successfully to solve two case studies based on Portuguese cascaded hydro systems, providing a higher profit at an acceptable computation time in comparison with classical optimisation methods based on mixed-integer linear programming (MILP).

Evaluation of exposure parameters in plain radiography: a comparative study with european guidelines

Typical distribution of exposure parameters in plain radiography is unknown in Portugal. This study aims to identify exposure parameters that are being used in plain radiography in the Lisbon area and to compare the collected data with European references [Commission of European Communities (CEC) guidelines]. The results show that in four examinations (skull, chest, lumbar spine and pelvis), there is a strong tendency of using exposure times above the European recommendation. The X-ray tube potential values (in kV) are below the recommended values from CEC guidelines. This study shows that at a local level (Lisbon region), radiographic practice does not comply with CEC guidelines concerning exposure techniques. Further national/local studies are recommended with the objective to improve exposure optimisation and technical procedures in plain radiography. This study also suggests the need to establish national/local diagnostic reference levels and to proceed to effective measurements for exposure optimisation.

A practical approach for profit-based unit commitment with emission limitations

This paper proposes a practical approach for profit-based unit commitment (PBUC) with emission limitations. Under deregulation, unit commitment has evolved from a minimum-cost optimisation problem to a profit-based optimisation problem. However, as a consequence of growing environmental concern, the impact of fossil-fuelled power plants must be considered, giving rise to emission limitations. The simultaneous address of the profit with the emission is taken into account in our practical approach by a multiobjective optimisation (MO) problem. Hence, trade-off Curves between profit and emission are obtained for different energy price profiles, in a way to aid decision-makers concerning emission allowance trading. Moreover, a new parameter is presented, ratio of change, and the corresponding gradient angle, enabling the proper selection of a compromise commitment for the units. A case study based on the standard IEEE 30-bus system is presented to illustrate the proficiency Of Our practical approach for the new competitive and environmentally constrained electricity supply industry.

Optimização de recursos na construção de linhas de caminhos de ferro

Os Caminhos-de-ferro representam um conjunto de abordagens quase ilimitadas, nestes termos, o tema proposto – “A optimização de recursos na construção de linhas de Caminhos de Ferro”, incidirá particularmente sobre a optimização dos recursos: i) materiais; ii) mão-de-obra; iii) equipamentos, afectos a construção da via e da catenária. O presente estudo pretende traçar um encadeamento lógico e intuitivo que permita manter um fio condutor ao longo do todo o seu desenvolvimento, razão pela qual, a sequência dos objectivos apresentados constitui um caminho que permitira abrir sucessivas janelas de conhecimento. O conhecimento da via e da catenária, a compreensão da forma como os trabalhos interagem com os factores externos e a experiência na utilização das ferramentas de planeamento e gestão, são qualidades que conduzem certamente a bons resultados quando nos referimos a necessidade de optimizar os recursos na construção da via e da catenária. A transmissão e reciprocidade da informação, entre as fases de elaboração de propostas e de execução da obra, representam um recurso que pode conduzir a ganhos de produtividade. A coordenação e outro factor determinante na concretização dos objectivos de optimização dos recursos, que se efectua, quer internamente, quer exteriormente. A optimização de recursos na construção da via e da catenária representa o desafio permanente das empresas de construção do sector ferroviário. E neste pressuposto que investem na formação e especialização da sua mão-de-obra e na renovação tecnológica dos seus equipamentos. A optimização dos materiais requer aproximações distintas para o caso da via e para o caso da catenária, assim como, os equipamentos e a mão-de-obra não podem ser desligados, pois não funcionam autonomamente, no entanto a respectiva optimização obedece a pressupostos diferentes.

MASDSheGATS – Scheduling System for Dynamic Manufacturing Environments

This chapter addresses the resolution of scheduling in manufacturing systems subject to perturbations. The planning of Manufacturing Systems involves frequently the resolution of a huge amount and variety of combinatorial optimisation problems with an important impact on the performance of manufacturing organisations. Examples of those problems are the sequencing and scheduling problems in manufacturing management, routing and transportation, layout design and timetabling problems.

Addressing the facilities layout design problem through constraint logic programming

One of the most difficult problems that face researchers experimenting with complex systems in real world applications is the Facility Layout Design Problem. It relies with the design and location of production lines, machinery and equipment, inventory storage and shipping facilities. In this work it is intended to address this problem through the use of Constraint Logic Programming (CLP) technology. The use of Genetic Algorithms (GA) as optimisation technique in CLP environment is also an issue addressed. The approach aims the implementation of genetic algorithm operators following the CLP paradigm.

Virtual power producers market strategies

This paper presents MASCEM - a multi-agent based electricity market simulator. MASCEM uses game theory, machine learning techniques, scenario analysis and optimisation techniques to model market agents and to provide them with decision-support. This paper mainly focus on the MASCEM ability to provide the means to model and simulate Virtual Power Producers (VPP). VPPs are represented as a coalition of agents, with specific characteristics and goals. The paper detail some of the most important aspects considered in VPP formation and in the aggregation of new producers and includes a case study.

Natural gas system operation: lagrangean optimization techniques

To comply with natural gas demand growth patterns and Europe´s import dependency, the gas industry needs to organize an efficient upstream infrastructure. The best location of Gas Supply Units – GSUs and the alternative transportation mode – by phisical or virtual pipelines, are the key of a successful industry. In this work we study the optimal location of GSUs, as well as determining the most efficient allocation from gas loads to sources, selecting the best transportation mode, observing specific technical restrictions and minimizing system total costs. For the location of GSUs on system we use the P-median problem, for assigning gas demands nodes to source facilities we use the classical transportation problem. The developed model is an optimisation-based approach, based on a Lagrangean heuristic, using Lagrangean relaxation for P-median problems – Simple Lagrangean Heuristic. The solution of this heuristic can be improved by adding a local search procedure - the Lagrangean Reallocation Heuristic. These two heuristics, Simple Lagrangean and Lagrangean Reallocation, were tested on a realistic network - the primary Iberian natural gas network, organized with 65 nodes, connected by physical and virtual pipelines. Computational results are presented for both approaches, showing the location gas sources and allocation loads arrangement, system total costs and gas transportation mode.

Multidimensional aspects related to shiftworkers' health and well-being

The impact of shift and night work on health shows a high inter- and intra-individual variability, both in terms of kind of troubles and temporal occurrence, related to various intervening factors dealing with individual characteristics, lifestyles, work demands, company organisation, family relations and social conditions. The way we define "health" and "well-being" can significantly influence appraisals, outcomes and interventions. As the goal is the optimisation of shiftworkers' health, it is necessary to go beyond the health protection and to act for health promotion. In this perspective, not only people related to medical sciences, but many other actors (ergonomists, psychologists, sociologists, educators, legislators), as well as shiftworkers themselves. Many models have been proposed aimed at describing the intervening variables mediating and/or moderating the effects; they try to define the interactions and the pathways connecting risk factors and outcomes through several human dimensions, which refer to physiology, psychology, pathology, sociology, ergonomics, economics, politics, and ethics. So, different criteria can be used to evaluate shiftworkers' health and well-being, starting from biological rhythms and ending in severe health disorders, passing through psychological strain, job dissatisfaction, family perturbation and social dis-adaptation, both in the short- and long-term. Consequently, it appears rather arbitrary to focus the problem of shiftworkers' health and tolerance only on specific aspects (e.g. individual characteristics), but a systemic approach appears more appropriate, able to match as many variables as possible, and aimed at defining which factors are the most relevant for those specific work and social conditions. This can support a more effective and profitable (for individuals, companies, and society) adoption of preventive and compensative measures, that must refer more to "countervalues" rather than to "counterweights".

Reported missing - learners in SLA/EFL research

Versão integral da revista no link do editor

Azorean Agriculture Efficiency by PAR

Copyright © 2013 Springer Netherlands.

Monitorização integrada para sistemas de alimentação distribuídos

Mestrado em Engenharia Electrotécnica e de Computadores