三角洲储层孔隙结构模型与剩余油分布研究——以临南油田沙河街组储层为例

The study of pore structure in reservoir was paid attention to in the early reservoir research and now a systematic research methodology is set up. On the limits of tools and conditions, methodologies and technologies on formation condition and distribution laws of pore structure and the relationship between remaining oil distribution and pore structure are uncertain and some knownage about it is also uncertain. As the development of petroleum industry, the characterization of pore structure and the prediction of remaining oil are the hot spot and difficult point in the research of oil development. The author pays a close attention to this subject and has done much research on it. In a case study in Linnan oilfield Huimin sag Jiyang Depression Bohai Bay basin by using a new method, named varied scale comprehensive modeling of pore structure, the author builds pore structure models for delta reservoir, reveals the remaining oil distribution laws in delta facies, and predicts the distribution of remaining oil in Linnan oilfield. By the application of stratigraphy, sedimentology and structure geology. the author reveals the genetic types of sandbody and its distribution laws, builds the reservoir geological models for delta sandstone reservoir in Shahejie group in Linnan oilfield and points out the geological Factors that control the development of pores and throats. Combining petrology and the reservoir sensitive analysis, the author builds the rock matrix models. It is the first time to state that rocks in different sentimental micro facies have different sensitive .response to fluid pressed into the rocks. Normally. the reservoirs in the delta front have weaker sensitivity to fluid than the reservoirs in delta plain, In same subfacies, the microfacies that have fine grain, such as bank and crevasse splay, have stronger reservoir sensitivity than the microfacies that have coarse grains, such as under-water branched channel and debauch bar. By the application of advanced testing, such as imagine analysis, scan electronic microscope, and morphology method, the author classifies the pore structure and set up the distribution models of pore, throat and pore structure. By the application of advanced theory in well-logging geology, the author finds the relationship between microscope pore structure and macroscopic percolation characteristics, and then builds the well-logging interpretation formulae for calculating pore structure parameters. By using the geostatistics methods, the author reveals the spatial correlative characteristics of pore structure. By application of conditional stochastic simulation methods, the author builds the 3D models of pore structure in delta reservoir. It is the base of predicting remaining oil distribution. By a great deal of experiments and theoretical deduction, The author expounds the laws of percolation flow in different pore structures, and the laws by which the pore structure controls the micro distribution of remaining oil, and then, states the micro mechanism of remaining oil distribution. There are two types of remaining oil. They are by-pass flow caused by micro-fingering and truncation caused by non-piston movement. By new method, the author states the different pore structure has different replacement efficiency, reveals the formation condition and distribution laws of remaining oil. predicts the remaining oil distribution in Linnan oil field, and put forward some idea about how to adjust the oil production. The study yielded good results in the production in Linnan oilfield.

云南岩石圈流变学及多震层孕震环境

The Study on rheology of the lithosphere and the environments of the seismogenic layer is currently the basic project of the international earthquake research. Yunnan is the ideal place for studying this project. Through the multi-disciplinary comprehensive study of petrology, geophysics, seismo-geology, rock mechanics, etc., the depth-strength profiles of the lithosphere have been firstly constructed, and the seismogenic layer and its geophysical and tectonic environments in Yunnan have been systematically expounded in this paper. The related results achieved are of the important significances for further understanding the mechanism of strong earthquake generation, dividing the potential foci and exposing recent geodynamical processes in Yunnan. Through the comprehensive contrast of the metamorphic rocks in early and middle Proterozoic outcropping on the surface, DSS data and experimental data of rock seismic velocity under high temperature and high pressure, the petrological structure of the crust and upper mantle has been studied on Yunnan: the upper, middle and lower crust is composed of the metamorphic rocks of greenschist, amphibolite and granulite facies, respectively or granitoids, diorites and gabbros, respectively, and the upper mantle composed of the peridotites. Through the contrast studies of the heat flow and epicenters of the strong earthquakes, the distribution of the geotemperature and the data of focal depth, the relationship of between seismicity and geothermal structure of the lithosphere in Yunnan has been studied: the strong earthquakes with magnitude M ≥ 6.0 mainly take place at the geothermal gradient zone, and the seismic foci densely distribute between 200～500 ℃ isogeotherms. On the basis of studies of the rock properties and constituents of the crust and upper mantle and geothermal structure of the lithosphere, the structure of the rheological stratification of the lithosphere has been studied, and the corresponding depth-strength profiles have been constructed in Yunnan. The lithosphere in majority region of Yunnan has the structure of the rheological stratification, i.e. the brittle regime in the upper crust or upper part of the upper crust, ductile regime in the middle crust or lower part of the upper crust to middle crust, ductile regime in the lower crust and ductile regime in the subcrustal lithosphere. The rheological stratification has the quite marked lateral variations in the various tectonic units. The distributions of the seismogenic layer have been determined by using the high accurate data of focal depth. Through the contrast of the petrological structure, the structure of seismic velocity, electric structure, geotemperature structure, and rheological structure and the study of the focal mechanism in the seismogenic layer, the geophysical environments of the seismogenic layer in Yunnan have been studied. The seismogenic layer in Yunnan is located at the depths of 3 ～ 20 km; the rocks in the seismogenic layer are composed of the metamorphic rocks of greenschist to amphibolite facies (or granites to diorites); the seismogenic layer and its internal focal regions of strong earthquakes have the structure of medium properties with the relatively high seismic velocity, high density and high resistivity; there exists the intracrustal low seismic velocity and high conductivity layer bellow the seismogenic layer, the geotemperature is generally 100～500 ℃ in the depth range in which the seismogenic layer is located. The horizontal stress field predominates in the seismogenic layer, the seismogenic layer corresponds to the brittle regime of the upper crust or brittle regime of the upper crust to semibrittle regime of the middle crust. The formation of the seismogenic layer, preparedness and occurrence of the strong earthquakes is the result of the comprehensive actions of the source fault, rock constituent, structure of the medium properties, distribution of the geotemperature, rheological structure of the seismogenic layer and its external environments. Through the study of the structure, active nature, slip rate, segmentation of the active faults, and seismogenic faults, the tectonic environments of the seismogenic layer in Yunnan have been studied. The source faults of the seismogenic layer in Yunnan are mainly A-type ones and embody mainly the strike slip faults with high dip angle. the source faults are the right-lateral strike slip ones with NW-NNW trend and left-lateral strike slip ones with NE-NEE trend in Southwestern Yunnan, the right-lateral strike slip ones with NNW trend and left-lateral strike slip ones with NNE trend (partially normal ones) in Northwestern Yunnan, the right-lateral strike slip ones with NWW trend in Central Yunnan and left-lateral strike slip ones with NW-NNW trend in Eastern Yunnan. Taking Lijiang earthquake with Ms = 7.0 for example. The generating environments of the strong earthquake and seismogenic mechanical mechanism have been studied: the source region of the strong earthquake has the media structure with the relatively high seismic velocity and high resistivity, there exists the intracrustal low velocity and high conductivity layer bellow it and the strong earthquakes occur near the transitional zone of the crustal brittle to ductile deformation. These characteristics are the generality of the generating environments of strong earthquakes. However, the specific seismogenic tectonic environments and action of the stress field of the seismic source in the various regions, correspondingly constrains the dislocation and rupture mechanical mechanism of source fault of strong earthquake.

大别山碰撞造山带逆冲推覆构造运动学和动力学研究

Since the discovery of coesite-bearing eclogites in Dabie and Sulu region over ten years ago, the Dabie collisional orogen has been the "hot-spot" across the world. While many great progresses have been made for the last decade in the researches on the Dabie and Sulu UHP metamorphic rocks in the following fields, such as, petrology, mineralogy, isotope chronology, and geochemistry, the study of the structural geology on the Dabie orogen is still in great need. Thrust and nappe tectonics commonly developed in any collisional orogenic belt during the syncollisional process of the orogen. It is the same as the Dabic collisional orogen is concerned. The paper put much stress on the thrust and nappe tectonics in the Dabic orogenic belt, which have been seldom systematically studied before. The geometric features including the division and the spatial distribution of various thrust and nappe tectonics in the Dabie orogen have been first studied, which is followed by the detailed studies on their kinematic characteristics in different scales varying from regional tectonics to microtectonics. In the thesis, new deformation ages have been obtained by the isotopic methods of ~(40)Ar-~(39)Ar, Sm-Nd and Rb-Sr minerals-whole rock isochrons on the mylonites formed in three ductile shear zones which bounded three different major nappes in the Dabie collisional orogenic belt. And the petrological, geochemical characteristics of some metamorphic rocks as well as the geotectonics of their protoliths, which have also deformed in the ductile shear zone, are analyzed and discussed. In the paper, twelve nappes in the Dabie orogen are first divided, which are bounded by various important NWW or NW-strike faults and three NNE-strike faults. They are Shangcheng Nappe, Huoshan Nappe, Yuexi Nappe, Yingshanjian-Hengzhong Nappe, Huangzhen Nappe, Xishui-Huangmei Nappe, Zhoudang Nappe, Suhe-Huwan Nappe, Xinxian Nappe, Hong'an Nappe, Mulan Nappe and Hhuangpi-Susong Nappe. In the Dabie orogen, three types of thrust and nappe tectonics belonging to two stages have been confirmed. They are: (1) early stage ductile thrust -nappe tectonics which movement direction was top-to-the-south; (2) late stage brittle to ductile-brittle thrust-nappe tectonics which are characterized by double-vergence movement, including top-to-the-north and top-to-the-south; (3) the third type also belongs to the late stage which also characterized by double-vergence movement, including top-to-the-east and top-to-the-west, and related to the strike-slip movement. The deformation ages of both Wuhe-Shuihou ductile shear zone and Taihu-Mamiao ductile shear zone have been dated by ~(40)Ar-~(39)Ar method. ~(40)Ar/~(39)Ar plateau ages of biotite and mica from the mylonites in these two shear zones are 219.57Ma and 229.12Ma. The plateau ages record the time of ductile deformation of the ductile shear zones, which made the concerned minerals of the mylonites exhume from amphibolite facies to the middle-upper crustal conditions by the early stage ductile thrust-nappe tectonics. The mineral isochons of Sm-Nd and Rb-Sr dating on the same mylonite sample of the metamafic rocks are 156.5Ma and 124.56Ma respectively. The two isochron ages suggest that the mylonitic rock strongly deformed in the amphilbolite facies at 156Ma and then exhumed to the upper crustal green schist condition at 124Ma with the activities of the Quiliping-Changlinggang ductile shear zone which bounded to the southen edge of Xinxian Nappe. Studies of the petrological and geochemical characteristics of some meta-mafic rocks and discussion on the geotectonics of their protoliths indicate that their protoliths were developped in an island arc or back-arc basin or active continental margin in which calc-alkline basalts formed. This means that arc-accretion orogeny had evolved in the margins of North china plate and/or Yangtze plate before these two plates directly collided with each other during the evolution process of Dabie orogen. Three-stage evolution of the thrust-nappe tectonics in Dabie collisional orogen has been induced based on the above-mentioned studies and previous work of others. And a possible 3-stage exhumation model (Thrust-Positive Flower Structure Model) has also been proposed.

内蒙古东部喀喇沁地区早中生代底侵作用

Mafic granulite xenoliths have been extensively concerned over the recent years because they are critical not only to studies of composition and evolution of the deep parts of continental crust but to understanding of the crust-mantle interaction. Detailed petrology, geochemistry and isotope geochronology of the Early Mesozoic mafic-ultramafic cumulate xenoliths and mafic granulite xenoliths and their host diorites from Harqin area, eastern Inner-Mongolia have been studied here. Systematic Rb-Sr isochron, ~(40)Ar-~(39)Ar and K-Ar datings for mafic-ultramafic cumulate xenoliths give ages ranging from 237Ma to 221Ma. Geochemical research and forming temperature and pressure estimates suggest that cumulates are products of the Early Mesozoic mantle-derived magmatic underplating and they formed in the magmatic ponds at the lowermost of the continental crust and are later enclaved by the dioritic magma. Detailed study on the first-discovered mafic granulite xenoliths reveals that their modal composition, mineral chemistry and metamorphic P-T conditions are all different from those of the Precambrian granulite exposed on the earth surface of the North China craton. High-resolution zircon U-Pb dating suggests that the granulite facies metamorphism may take place in 253 ～ 236Ma. Hypersthene single mineral K-Ar dating gives an age of 229Ma, which is believed to represent a cooling age of the granulite. As the host rock of the cumulate and granulite xenoliths, diorites intruded into Archean metamorphic rocks and Permian granite. They are mainly composed of grandodiorite, tonalite and monzogranite and show metaluminous and calc-alkaline features. Whole rock and single mineral K-Ar dating yields age of 221 ～ 223Ma, suggesting a rapid uplift in the forming process of the diorites. Detailed field investigation and geochemical characteristics indicate that these diorites with different rock types are comagmatic rocks, and they have no genetic correlation with cumulate and granulite xenoliths. Geochemical model simulating demonstrates that these diorites in different lithologies are products of highly partial melting of Archean amphibolite. It is considered that the Early Mesozoic underplating induced the intrusion of diorites, and it reflects an extensional geotectonic setting. Compression wave velocity V_P have been measured on 10 representative rock samples from the Early Mesozoic granulite and mafic-ultramafic cumulate xenoliths population as an aid to interpret in-situ seismic velocity data and investigating velocity variation with depth in a mafic lower crust. The experiments have been carried out at constant confining pressures up to 1000MPa and temperatures ranging from 20 ℃ to around 1300 ℃, using the ultrasonic transmission technique. After corrections for estimated in situ crustal pressures and temperatures, elastic wave velocities range from 6.5 ～ 7.4 km s~(-1). On the basis of these experimental data, the Early-Mesozoic continental compression velocity profile has also been reestablished and compared with those of the present and of the different tectonic environments in the world. The result shows that it is similar to the velocity structure of the extensional tectonic area, providing new constraints on the Early Mesozoic continental structure and tectonic evolution of the North-China craton. Combining with some newly advancements about the regional geology, the thesis further proposes some constraints on the Mesozoic geotectonic evolution history, especially the features of deep geology of the North China craton.

晚中生代松辽盆地形成的大地构造环境及成因机制

Directed by the theory of "Collision Tectonic Facies", the tectonic setting and dynamic mechanism of the formation of Songliao basin in late Mesozoic (J_3-K_1) are studied in the present thesis with the methods of petrology, petrochemistry, geochemistry and isotopic geochronology. The research contents in this paper include as followings. Firstly, the general tectonic frame is made up of different tectonic facies formed from Mid-late Proterozoic to Mesozoic, which are Huabei plate, the Chengde-Siziwangqi melange (Pz_1), the Wenduermiao magmatic arc (Pz_1), the Hegenshan-Chaogenshan melange (Pz_2), the accretion arec (Pz_1-P), the Raohe-Hulin melange (Mz), the magmatic arc (Mz) and the pull-apart basin on the magmatic arc (Mz). Secondly, the volcanic rock assemblages of Songliao basin and its adjacent area in late Mesozoic is the typical calc-alkaline of the magmatic arc. The types of volcanic rocks in the study area include basalts, basaltic andesites, andesites, dacites and rhyolites, and basic-intermediate volcanic rocks have higher alkalinity. The volcanic rock series in this area is the high-K calc-alkaline series. Thirdly, the total REE of volcanic rocks in Songliao basin and its adjacent area is higher than that of the chondrite. The pattern of the REE normalized by the chondrite shows the characteristics similar to that of the typical island arcs or the active continental margins in the earth, that is enrichment of LREE and depletion of Eu. The spider-diagram of the trace element normalized by the primitive mantle also expresses the similar features to that of the typical island arcs or the active continental margins, it has distinctive valleies of Nb, Ta, Sr, P, and Ti, as well as the peaks of La, Ce, Th, U, and K. The incompatible elements show that the high field strength elements, such as Nb, Ta, Ti, and P, are depletion while the low field strength elements, such as K, U, Pb, and Ba, are enrichment. These features are similar to those of orogenic volcanic rocks and imply the formation of the volcanic rocks in this area is related to the subduction. The degrees of both the enrichment of the HFS elements and depletion of the LFS elements become more obvious from basic to acid volcanic rocks, which suggests crustal contamination enhances with the magmatic crystallization and fractionation. The concentration of the compatible elements is W-shape, and anomalies in Cr and Ni suggest there is the contamination during the magmatic crystallization and fractionation. Fourthly, the isotopic age data prove the volcanic activity in the Songliao basin and its adjacent area started in the early-middle Jurassic, and ended in the end of the early Cretaceous-the beginning of the Cretaceous. The volcanism summit was the late Jurassic-the early Cretaceous (100 - 150Ma). Finally, the tectonic setting of volcanism in the late Mesozoic was magmatic arc, which originated the subduction of Raohe-Hulin trench to the northwest Asian plate. The subduction began in the middle Jurassic, and the collision orogenesis between the Sikhote-Alin arc and Asian continent was completed in the end of the early Cretaceous-the beginning of the late Cretaceous. The results of above tectonic processes were finally to format Nadanhada orogenic belt symbolized by the Raohe-Hulin suture or melange belt. The violently oblique movement of the Izanagi plate toward Asian plate in the late Mesozoic was the dynamic mechanism of above tectonic processes. At the same tome, the left-lateral strike-slip shear caused by the oblique movement of the Izanagi plate produced a series of strike-slip faults in east Asian margin, and the large scale displacements of these strike-slip faults then produced the pull-apart basing or grabens on the magmatic arc. Conclusively, the tectonic setting during the formation of the grabens of Songliao basin in the late Mesozoic was magmatic arc, and its dynamic mechanism was the pull-apart. In a word, there was a good coupling relation among the oblique subduction of the oceanic plate, collisional orogene between island arc and continental plate, strike-slip shear of the faults and the formation of the grabens in Songliao basin and its adjacent area in late Mesozoic. These tectonic processes were completed in the unoin dynamic setting and mechanism as above description.

油气运聚动力学的模拟分析——以准噶尔盆地为例

The petroleum migration, happening in the geologic past, is the very important and complex dynamic processes in the petroleum systems. It plays a linking role among all static factors in a system. The accumulation is in fact the result of the petroleum migration. For the petroleum geology, the dynamics research of the petroleum migration refers to the mechanism and process research, as well as the use of the quantitative methods. In this thesis, combining with the qualitative analysis and quantitative modeling, the author manages to discuss theoretically some key problems dealing with migration processes, which have not been solved yet, and to apply the studied results in petroleum system analysis in actual basins. The basin analysis offers the base of the numerical modeling for geological phenomena occurring in sedimentary basins, that consists of the sedimentary facies analysis, the section reconstructing technique, eroded thickness estimating, etc. The methods to construct the geologic model, which is needed in the research of oil and gas migration and accumulation, are discussed. The basin analysis offers also the possibility for the latter modeling works to get and select the parameters, such as stratum's thickness, age, stratigraphy etc. Modeling works were done by using two basin modeling softwares: Basin_Mod and TPC_Mod. The role of compaction during the secondary migration and the heterogeneity of migrating paths within the clastic carrier are modeled. And the conclusions were applied in the migration studies in the Jungaer Basin, lying on the Northwest part of the China. To construct a reliable migration model, the author studied the characteristics of the sedimentation, the pore fluid pressure evolution, as well as the distribution and the evolution of fluid potential, following the tectonic evolution of the Jungaer Basin. The geochemical prospecting results were used to evidence and to calibrate the migration processes: the oil-source correlation, the distribution of the properties of oil, gas and water. Finally, two important petroleum systems, Permian one and Jurassic one were studied and identified, according, principally, to the studies on the petroleum migration within the Jungaer Basin. Since the oil, as well as the gas, moves mainly in separate phase during the secondary migration, their migrating behaviors would be determined by the dynamics conditions of migration, including the driving forces and pathways. Based on such a consideration, the further understandings may be acquired: the roles played by permeable carriers and low-permeable source rock would be very different in compaction, overpressure generation, petroleum migration, and so on. With the numerical method, the effect of the compaction on the secondary migration was analyzed and the results show that the pressure gradient and the flux resulted from compaction are so small that could be neglected by comparing to the buoyancy of oil. The main secondary migration driving forces are therefore buoyancy and capillary within a hydrostatic system. Modeling with the commercial software-Basin_Mod, the migration pathways of petroleum in clastic carriers seem to be inhomogeneous, controlled by heterogeneity of the driving force, which in turn resulted from the topography of seals, the fabrics and the capillary pressure of the clastic carriers. Furthermore, the direct and indirect methods to study fault-sealing properties in the course of migration were systemically summarized. They may be characterized directly by lithological juxtaposition, clay smear and diagenesis, and indirectly the comparing the pressures and fluid properties in the walls at two apartments of a fault. In Jungaer Basin, the abnormal pressures are found in the formations beneath Badaowan or Baijantan Formation. The occurrence of the overpressure seems controlled by the stratigraphy. The rapid sedimentation, tectonic pressuring, clay sealing, chemical diagensis were considered as the principal pressuring mechanisms. The evolution of fluid pressure is influenced differently at different parts of the basin by the tectonic stresses. So the basin appears different pressure evolution cycles from each part to another during the geological history. By coupling the results of thermal evolution, pressure evolution and organic matter maturation, the area and the period of primary migration were acquired and used to determine the secondary migration time and range. The primary migration in Fengcheng Formation happened from latter Triassic to early Jurassic in the main depressions. The main period of lower-Wuerhe Formation was at latter Jurassic in Changji, Shawan and Pen-1-jing-xi Depression, and at the end of early Cretaceous in Mahu Depression. The primary migration in Badaowan and Sangonghe Formation is at the end of early-Cretaceous in Changji Depression. After then, the fluid potential of oil is calculated at the key time determined from area and time of the primary migration. Generally, fluid potential of oil is high in the depressions and low at the uplifts. Synthetically, it is recognized that the petroleum migration in the Jungaer Basin is very complex, that leads us to classify the evolution of petroleum systems in Northwestern China as a primary stage and a reformed one. The remigration of accumulated petroleum, caused by the reformation of the basin, results in the generation of multiple petroleum systems. The faults and unconformities are usually the linkers among the original petroleum systems. The Permian petroleum system in Jungaer Basin is such a multiple petroleum system. However, the Jurassic petroleum system stays still in its primary stage, thought the strong influences of the new tectonic activities.

阿尔金蛇绿混杂带构造岩石组合及其大地构造意义

The Alytn fault is a huge left-slip fault zone within the Asian continent, and locates such zone that is linked to main tectonic units in the western China, which makes it is very important to the tectonic framework and ore distribution in the western China. Selecting two ophiolite zones (namely Hongliugou-Lapeiquan ophiolite zone and Sulamutage ophiolite zone) respectively located within the southern and northern part of the Altyn fault and based on analysis of field geology characteristics and geochemistry, this paper recognized the rock types (mainly mafic and ultramafic rocks) within the melanges and subdivided each lithological unit based on tectonic environment. At last, this paper rebuilt the paleo-tectonic framework in the Alytn region by the method of tectonic facies and discussed its tectonic evolution with the theory of collision orogens. Combining former results with hard field observation and geochemical analysis, this paper acquired such recognitions to two ophiolte zones within the Altyn fault zone as follows: To the typical regions (Hongliugou, Lapeiquan, Mangya and Sulamutage) within the two ophiolte zones in the Altyn fault zone, this paper offered the field geology profiles. Field geology characteristics show that they are composed of melange bases (mainly abyssal flysch and carbonate rocks) and melange blocks from various tectonic environments, often with fault contact among each lithological units, belonging to typical ophiolitic melange zone. The ultramafic rocks outcropped at the Altyn region are all harzburgites. Remant grains of primary minerals have melted residual texture and elastic deformation texture under high temperature and pressure. The whole-rock analyses show their low TiO_2 contents (0.01～0.04%), low Al, Ca and high MgO contents and wide Mg~# range (89.35～95.57). Rare earth patterns have two types, namely tabacco pipe-shped and LREE-shaped, of which the former is often seen. The chondrite-nomalized Yb values of these analyses are all lower than 1. The spinels have low Ti and high Cr content and most spinels have Cr# higher than 60. All of the above characteristics show that the ultramafic rocks in the Altyn fault zone are components of metmorphic peridotites of ophiolite from depleted mantle source and most ophiolites from this zone belong to supra-subduction zone (SSZ) type ophiolite with a few mid-ocean ridge basalt (MORB) type. Geochemical analyses show that the melange blocks within the Altyn ophiolitic melange zone have different characteristics from various tectonic environments. This paper recognized such tectonic-lithological assemblages as mid-ocean basalts, oceanic island basalts, oceanic island arc tholeiites, island arc calalkaline basalts and island arc granites and inferred that these tectonic-lithological units respectively belongs to such tectonic units as ophiolites, oceanic islands and/or oceanic seamounts, oceanic island arc and a~creting arcs, which show these blocks from oceanic crust and subduction zone for the most part. For the Altyn ophiolites, the chronological data show they become new from the north to the south. Combined with the study on late slip of Altyn fault and North Qilianshan orogeny, the author inferred that the Altyn region had belonged to one part of the North Qilianshan accreting wedge-arc orogeny at paleozoic, and later huge left-slip made it locate modem site.

东海陆架盆地西南部烟囱构造与油气运聚关系研究

In recent years, chimney structure has been proved one of important indicators and a useful guide to major petroleum fields exploration through their exploration history both at home and abroad. Chimney structure, which has been called "gas chimney" or "seismic chimney", is the special fluid-filled fracture swarm, which results from the boiling of active thermal fluid caused by abruptly decreasing of high pressure and high temperature in sedimentary layers of upper lithosphere. Chimney structure is well developed in continental shelf basin of East China Sea, which indicates the great perspectives of petroleum resources there. However, the chimney structure also complicated the petroleum accumulation. So the study of chimney structure on its formation, its effect on occurrence and distribution of petroleum fields is very important not only on theoretical, but also on its applied research. It is for the first time to make a clear definition of chimney structure in this paper, and the existence and practical meaning of chimney structure are illustrated. Firstly, on the viewpoint of exploration, this will amplify exploration area or field, not only in marine, but also on continent. Secondly, this is very important to step-by-step exploration and development of petroleum fields with overpressure. Thirdly, this will provide reference for the study on complex petroleum system with multi-sources, commingled sources and accumulation, multi-stage accumulations, and multi-suits petroleum system in the overlay basin. Fourthly, when the thermal fluid enters the oceanic shallow layer, it can help form gas hydrate under favorable low-temperature and high-pressure conditions. Meanwhile, the thermal fluid with its particular component and thermal content will affect the physical, chemical and ecological environments, which will help solving the problem of global resources and environment. Beginning from the regional tectonic evolution characteristics, this paper discussed the tectonic evolution history of the Taibei depression, then made an dynamical analysis of the tectonic-sedimentary evolution during the Mesozoic and Cenozoic for the East China Sea basin. A numerical model of the tectonic-thermal evolution of the basin via the Basin-Mod technique was carried out and the subsidence-buried history and thermal history of the Taibei depression were inverse calculated: it had undergone a early rapid rift and sag, then three times of uplift and erosion, and finally depressed and been buried. The Taibei depression contains a huge thick clastic sedimentary rock of marine facies, transitional facies and continental facies on the complex basement of ante-Jurassic. It is a part of the back-arc rifting basins occurred during the Mesozoic and Cenozoic. The author analyzed the diagenesis and thermal fluid evolution of this area via the observation of cathodoluminescence, scanning electron microscope and thin section, taking advantage of the evidences of magma activities, paleo-geothermics and structural movement, the author concluded that there were at least three tectonic-thermal events and three epochs of thermal-fluid activities; and the three epochs of thermal-fluid activities were directly relative to the first two tectonic-thermal events and were controlled by the generation and expulsion of hydrocarbon in the source rock simultaneously. Based on these, this paper established the corresponding model between the tectonic-thermal events and the thermal-fluid evolution of the Taibei Depression, which becomes the base for the study on the chimney structures. According to the analyses of the gas-isotope, LAM spectrum component of fluid inclusion, geneses of CO_2 components and geneses of hydrocarbon gases, the author preliminarily verified four sources of the thermal fluid in the Taibei Depression: ① dehydration of mud shale compaction, ② expulsion of hydrocarbon in the source rock; ③ CO_2 gas hydro-thermal decomposition of carbonatite; ④magma-derived thermal fluid including the mantle magma water and volatile components (such as H_2O, CO_2, H_2S, SO_2, N_2 and He etc.). On the basis of the vitrinite reflectance (Ro), homogenization temperature of fluid inclusion, interval transit time of major well-logging, mud density of the wells, measured pressure data and the results of previous studies, this paper analyzed the characteristics of the geothermal fields and geo-pressure fields for the various parts in this area, and discussed the transversal distribution of fluid pressure. The Taibei depression on the whole underwent a temperature-loss process from hot basin to cold basin; and locally high thermal anomalies occurred on the regional background of moderate thermal structure. The seal was primarily formed during the middle and late Paleocene. The overpressured system was formed during the middle and late Eocene. The formation of overpressured system in Lishui Sag underwent such an evolutionary process as "form-weaken-strengthen-weaken". Namely, it was formed during the middle and late Eocene, then was weakened in the Oligocene, even partly broken, then strengthened after the Miocene, and finally weakened. The existence of the thermal fluid rich in volatile gas is a physical foundation for the boiling of the fluid, and sharply pressure depletion was the major cause for the boiling of the fluid, which suggests that there exists the condition for thermal fluid to boil. According to the results of the photoelastic simulation and similarity physical experiments, the geological condition and the formation mechanism of chimnestructures are summarized: well compartment is the prerequisite for chimney formation; the boiling of active thermal fluid is the original physical condition for chimney formation; The local place with low stress by tension fault is easy for chimney formation; The way that thermal fluid migrates is one of the important factors which control the types of chimney structures. Based on where the thermal fluid come from and geometrical characteristics of the chimney structures, this paper classified the genetic types of chimney structures, and concluded that there existed three types and six subtypes chimney structures: organic chimney structures generated by the hydrocarbon-bearing thermal fluid in middle-shallow layers, inorganic and commingling-genetic chimney structures generated by thermal fluid in middle-deep layers. According to the seismic profiles interpretations, well logging response analysis and mineralogical and petrological characteristics in the study area, the author summarized the comprehensive identification marks for chimney structures. Especially the horizon velocity analysis method that is established in this paper and takes advantage of interval velocity anomaly is a semi-quantitative and reliable method of chimney structure s identification. It was pointed out in this paper that the occurrence of the chimney structures in the Taibei depression made the mechanism of accumulation complicated. The author provided proof of episodic accumulation of hydrocarbon in this area: The organic component in the boiling inclusion is the trail of petroleum migration, showing the causality between the boiling of thermal fluid and the chimney structures, meanwhile showing the paroxysmal accumulation is an important petroleum accumulation model. Based on the evolutionary characteristics of various types of chimney structures, this paper discussed their relationships with the migration-accumulation of petroleum respectively. At the same time, the author summarized the accumulating-dynamical models associated with chimney structures. The author analyzed such accumulation mechanisms as the facies state, direction, power of petroleum migration, the conditions of trap, the accumulation, leakage and reservation of petroleum, and the distribution rule of petroleum. The author also provides explanation for such practical problems the existence of a lot of mantle-derived CO_2, and its heterogeneous distribution on plane. By study on and recognition for chimney structure, the existence and distribution of much mantle-derived CO_2 found in this area are explained. Caused by tectonic thermal activities, the deep magma with much CO_2-bearing thermal fluid migrate upward along deep fault and chimney structures, which makes two wells within relatively short distance different gas composition, such as in well LF-1 and well LS36-1-1. Meanwhile, the author predicted the distribution of petroleum accumulation belt in middle-shallow layer for this area, pointed out the three favorable exploration areas in future, and provided the scientific and deciding references for future study on the commingling-genetic accumulation of petroleum in middle-deep layer and the new energy-gas hydrate.

济阳-昌潍坳陷火成岩油气藏体系形成机理和分布规律研究

Jiyang & Changwei depressions are two neighboring depressions in Bahai Bay Basin, the famous oil rich basin in East China. The exploration activities in the past 40 years has proved that, within the basins, there exists not only plentiful sandstone hydrocarbon reservoirs (conventional), but also abundant special reservoirs as igneous rock, mudstone and conglomerate ones which have been knowing as the unconventional in the past, and with the prospecting activity is getting more and more detailed, the unconventional reservoirs are also getting more and more important for further resources, among which, the igneous lithological reservoir be of significance as a new research and exploration area. The purpose of this paper is, with the historical researches and data as base, the System Theory, Practice Theory and Modern Comprehensive Petroleum Geology Theory as guide, the theoretical and practice break through as the goal, and the existing problems in the past as the break through direction, to explore and establish a valid reservoir formation and distribution models for igneous strata in the profile of the eastern faulted basins. After investigating the distribution of the igneous rocks and review the history of the igneous rocks reservoirs in basins, the author focused on the following issues and correspondingly the following progresses have been made: 1.Come to a new basin evolution and structure model named "Combined-Basin-bodies Model" for Jiyang even Eastern faulted basins based on the study on the origin and evolution of Jiyang & Changwei basins, depending on this model, every faulted basin in the Bo-hai Bay Basin is consisted of three Basin-Bodies including the Lower (Mesozoic), Middle (Early Tertiary) and the Upper (Late Tertiary) Bodies, each evolved in different geo-stress setting and with different basin trend, shape and igneous-sedimentary buildings system, and from this one to next one, the basin experienced a kind of process named "shape changing" and "Style changing". 2. Supposed a serious of new realizations as follows (1) There were "multi-level magma sources" including Upper mantel and the Lower, Middle and even the Upper Shell magma Chambers in the historical Magma Processes in the basins; (2) There were "multi-magma accessing or pass" from the first level (Mantel faults) to the second, third and fourth levels (that is the different levels of fault in the basin sediment strata) worked in the geo-historical and magma processes; (3) Three tectonic magma cycles and more periods have been recognized those are matched with the "Basin -body-Model" and (4)The geo-historical magma processes were non-homogeneous in time and space scale and so the magma rocks distributed in "zones" or "belts". 3. The study of magma process's effect on basin petroleum conditions have been made and the following new conclusions were reached: (1) the eruptive rocks were tend to be matched with the "caped source rock", and the magma process were favorable to the maturing of the source rocks. (2) The magma process were fruitful to the accumulation of the non-hydrocarbon reservoirs however a over magma process may damage the grade of resource rock; (3) Eruptive activity provided a fruitful environment for the formation of such new reservoir rocks as "co-eruptive turbidity sandstones" and "thermal water carbonate rocks" and the intrusive process can lead to the origin of "metamorphism rock reservoir"; (4) even if the intrusive process may cause the cap rock broken, the late Tertiary intrusive rocks may indeed provide the lateral seal and act as the cap rock locally even regionally. All above progresses are valuable for reconstructing the magma-sedimentary process history and enriching the theory system of modem petroleum geology. 4. A systematic classification system has been provided and the dominating factors for the origin and distribution of igneous rock reservoirs have been worked out based on the systematic case studies, which are as follows: (1) The classification is given based on multi-factors as the origin type, litho-phase, type of reservoir pore, reservoir ability etc., (2) Each type of reservoir was characterized in a detailed way; (3) There are 7 factors dominated the intrusive reservoir's characteristics including depth of intrusion, litho-facies of surrounding rocks, thickness of intrusive rock, intrusive facies, frequency and size of the working faults, shape and tectonic deformation of rock, erosion strength of the rock and the time of the intrusion ect., in the contrast, 4 factors are for eruptive rocks as volcanic facies, frequency and size of the working faults, strength of erosion and the thermal water processing. 5. Several new concept including "reservoir litho-facies", "composite-volcanic facies" and "reservoir system" ect. Were suggested, based on which the following models were established: (1) A seven reservoir belts model for a intrusive unit profile and further more, (2) a three layers cubic model consisted of three layer as "metamorphic roe layer", "marginal layer" and "the core"; (3) A five zones vertical reservoir sequence model consisted of five litho-facies named A, B, C, D and E for a original lava unit and furthermore three models respectively for a erosion, subsidence and faulted lava unit; (4) A composite volcanic face model for a lava cone or a composite cone that is consisted of three facies as "crater and nearby face", "middle slope" and "far slope", among which, the middle slope face is the most potential reservoir area and producible for oil & gas. 6. The concept of "igneous reservoir" was redefined as the igneous, and then a new concept of "igneous reservoir system" was supposed which means the reservoir system consisted of igneous and associated non-igneous reservoirs, with non-hydrocarbon reservoir included. 7. The origin and distribution of igneous reservoir system were probed and generalized for the exploration applications, and origin models of the main reservoir sub-systems have been established including those of igneous, related non-igneous and non-hydrocarbon. For intrusive rocks, two reservoir formation models have been suggested, one is called "Original or Primary Model", and the another one is "Secondary Model"; Similarly, the eruptive rock reservoirs were divided in three types including "Highly Produced", "Moderately Produced" and "Lowly Produced" and accordingly their formation models were given off; the related non-igneous reservoir system was considered combination of eight reservoirs, among which some ones like the Above Anticline Trap are highly produced; Also, the non-hydrocarbon. Trap system including five kinds of traps was discussed. 8. The concept models for four reservoir systems were suggested, which include the intrusive system consisted of 7 kinds of traps, the land eruptive system with 6 traps, the under water eruptive system including 6 kinds of traps and the non-hydrocarbon system combined by 5 kinds of traps. In this part, the techniques for exploration of igneous reservoir system were also generalized and probed, and based on which and the geological progresses of this paper, the potential resources and distributions of every reservoir system was evaluated and about 186 millions of reserves and eight most potential non-hydrocarbon areas were predicted and outlined. The author believe that the igneous reservoir system is a very important exploration area and its study is only in its early stage, the framework of this paper should be filled with more detailed studies, and only along way, the exploration of igneous reservoir system can go into it's really effective stage.

河流成因储层沉积微相与剩余油分布及形成机理研究

Based on the study of fluvial sandstone reservoir in upper of Guantao group in Gudao and Gudong oilfields, this paper first introduces A.D.Miall's(1996a) architectural-element analysis method that was summarized from ground outcrop scale into the reservoir formation research of the study area, more subtly divides sedimentary microfacies and establishes sedimentary model of research area.on this base, this paper summarizes the laws of residual oil distribution of fluvial formation and the control effect of sedimentary microfacies to residual oil distribution, and reveals residual oil formation mechanism. These results have been applied to residual oil production, and the economic effect is good. This paper will be useful for residual oil research and production and enhancement of oil recovery in similar reservoir. The major conclusions of this paper are as follows. 1. Using the architectural-element analysis method to the core data, a interfacial division scheme of the first to the dixth scale is established for the studied fluvial formation. 2.Seven architectural-elements are divided in upper of Guantao group of study area. The sandstone group 5～1+2 of Neogene upper Gutao group belongs to high sinuous fine grain meandering river, and the sandstone group 6 is sandy braided river. 3. Inter layer, the residual oil saturation of "non-main layer" is higher than "main layer", but the residual recoverable reserve of former is larger. Therefore, "main layer" is the main body of residual oil distribution. The upper and middle part of inner layer has lower permeability and strong seeping resistance. Addition to gravity effect in process of driving, its driving efficiency is low; residual oil saturation is high. Because of controlling of inside non-permeable interlayer or sedimentary construction, the residual oil saturation of non-driving or lower driving efficiency position also is high. On plane, the position of high residual oil saturation mostly is at element LV, CS, CH (FF), FF etc, Which has lower porosity and permeability, as well as lens sand-body and sand-body edge that is not controlled by well-net, non-perfect area of injection and production, lower press difference resort area of inter-well diffiuent-line and shelter from fault, local high position of small structure. 4.Microscopic residual oil mainly includes the non-moved oil in the structure of fine pore network, oil in fine pore and path, oil segment in pore and path vertical to flow direction, oil spot or oil film in big pore, residual oil in non-connective pore. 5.The most essential and internal controlling factor of fluvial formation residual oil distribution is sedimentary microfacies. Status of injection and production is the exterior controlling factor of residual oil distribution. 6. The controlling effect of formation sedimentary microfacies to residual oil distribution indicates inter-layer vertical sedimentary facies change in scale of injection and production layer-series, planar sedimentary face change and inner-layer vertical sedimentary rhythm and interbed in single layer to residual oil distribution. 7. It is difficult to clear up the inter-layer difference in scale of injection and production layer-series. The using status of minor layer is not good and its residual oil saturation is high relatively. It is obvious that inter-layer vertical sedimentary facies changes control inter-layer residual oil distribution at the same or similar conditions of injection and production. For fluvial formation, this vertical sedimentary facies change mainly is positive gyration. Namely, from down to top, channel sediment (element CHL, LA) changes into over-bank sediment (element LV, CR, CS). 8. In water-injection developing process of transverse connecting fluvial sandstone oil formation, injection water always comes into channel nearby, and breaks through along channel and orientation of high pressure gradient, does not expand into side of channel until pressure gradient of channel orientation changes into low. It brings about that water-driving status of over-bank sedimentary element formation (LV, CR, CS) is not good, residual oil saturation is high. In non-connective abandoned channel element (CH) formation with channel, because this reverse is difficult to control by injection and production well-series, its using status is not good, even terribly not good, residual oil is enrichment. 9. The rhythm and sedimentary structure, sedimentary facies change in single sand body brings about vertical changes of formation character, growth character of inner layer interbed. These are important factor of controlling and affecting vertical water spread volume and inner layer residual oil forming and distribution in single sand body. Positive rhythm, is the principal part of fluvial sandstone inner layer sedimentary rhythm. Namely, from down to upside, rock grain granularity changes from coarse to fine, seeping ability changes from strong to feebleness. It brings about that water-driving status of inner layer upside is not good, residual oil saturation is high. Inner layer interbed has different degree affecting and controlling effect to seeping of oil and water. Its affecting degree lies on interbed thickness, extending scale, position, and jeted segment of production or injection well. The effect of interbed at upside of oil formation to oil and water seeping is less; the effect of interbed at middle of oil formation to oil and water seeping is more. 10. Indoor experiment and research indicate that wettability, permeability step, vertical permeability, position of Kmax and ratio of oil viscousity and water viscousity all have great effect on the water-driving recovery ratio. 11. Microscopic residual oil distribution is affected and controlled by formation pore network structure, pressure field distribution, and oil characteristic. 12.The residual oil forming mechanism: the over-bank sedimentary element and upper part of a positive rhythm sandstone have fine pore and throat network, permeability is low, displacement pressure of pore and throat is high. The water-driving power usually falls short of displacement pressure that brings about injection water does not spread into these pore and throat network, thereby immovable oil area, namely residual oil, is formed. At underside of channel sedimentary element and positive rhythm sandstone, porosity and permeability is relatively high, connecting degree of pore and throat is high, displacement pressure of pore and throat is low. Thereby injection water is easy to enter into pore and throat, driving oil in them. Because the pore space is irregular, the surface of pore wall is coarse and non-flat. That the oil locate on concave hole of pore wall and the dead angle of pore, and the oil attaches on surface of pore wall by surface tension, are difficult to be peeled off, becoming water-driving residual oil (remaining oil). On the other hand, Because flowing section lessens, flowing resistance increase, action of capillary fore, or seeping speed decreases at process of transfer at pass narrow throat path in the course carried by driving water. The "oil drop", "oil bead", or "oil segment" peeled off by driving water is difficult to carry and to drive out by water at less pressure difference. Thereby they are enclosed in pore to form discontinuous residual oil. 13.This results described above have been applied in nine develop blocks of Gudao and Gudong oilfield. Its applying effect is marked through local injection production adjustment, deploying replacement well, repair hole, replacement envelop, block off water and profile control etc. Relative method and technology can be applied to other oil production area of Shengli oilfield, and obtain better economic and societal effect.

断陷湖盆缓坡带成藏模式研究

Halfgraben-like depressions have multiple layers of subtle traps, multiple coverings of oil-bearing series and multiple types of reservoirs. But these reservoirs have features of strong concealment and are difficult to explore. For this reason, many scholars contribute efforts to study the pool-forming mechanism for this kind of basins, and establish the basis for reservoir exploration and development. However, further study is needed. This paper takes HuiMin depression as an example to study the pool-forming model for the gentle slope belts of fault-depression lake basins. Applying multi-discipline theory, methods and technologies including sedimentary geology, structural geology, log geology, seismic geology, rock mechanics and fluid mechanics, and furthermore applying the dynamo-static data of oil reservoir and computer means in maximum limitation, this paper, qualitatively and quantitatively studies the depositional system, structural framework, structural evolution, structural lithofacies and tectonic stress field, as well as fluid potential field, sealing and opening properties of controlling-oil faults and reservoir prediction, finally presents a pool-forming model, and develops a series of methods and technologies suited to the reservoir prediction of the gentle slope belt. The results obtained in this paper richen the pool-forming theory of a complex oil-gas accumulative area in the gentle slope belt of a continental fault-depression basin. The research work begins with the study of geometric shape of fracture system, then the structural form, activity stages and time-space juxtaposition of faults with different level and different quality are investigated. On the basis of study of the burial history, subsidence history and structural evolution history, this paper synthesizes the studied results of deposition system, analyses the structural lithofacies of the gentle slope belt in the HuiMing Depression and its controlling roles to oil reservoir in the different structural lithofacies belts in time-space, and presents their evolution patterns. The study of structural stress field and fluid potential field indicates that the stress field has a great change from the Dong Ying stages to nowadays. One marked point among them is that the Dong Ying double peak- shaped nose structures usually were the favorable directional area for oil and gas migration, while the QuDi horst became favorable directional area since the GuanTao stage. Based on the active regular of fractures and the information of crude oil saturation pressure, this paper firstly demonstrates that the pool-forming stages of the LingNan field were prior to the stages of the QuDi field, whici provides new eyereach and thinking for hydrocarbon exploration in the gentle slope belt. The BeiQiao-RenFeng buried hill belt is a high value area with the maximum stress values from beginning to end, thus it is a favorable directional area for oil and gas migration. The opening and sealing properties of fractures are studied. The results obtained demonstrate their difference in the hydrocarbon pool formation. The seal abilities relate not only with the quality, direction and scale of normal stress, with the interface between the rocks of two sides of a fault and with the shale smear factor (SSF), but they relate also with the juxtaposition of fault motion stage and hydrocarbon migration. In the HuiMin gentle slope belt, the fault seal has difference both in different stages, and in different location and depth in the same stage. The seal extent also displays much difference. Therefore, the fault seal has time-space difference. On the basis of study of fault seal history, together with the obtained achievement of structural stress field and fluid potential field, it is discovered that for the pool-forming process of oil and gas in the studied area the fault seal of nowadays is better than that of the Ed and Ng stages, it plays an important role to determine the oil column height and hydrocarbon preservation. However, the fault seal of the Ed and Ng stages has an important influence for the distribution state of oil and gas. Because the influential parameters are complicated and undefined, we adopt SSF in the research work. It well reflects synthetic effect of each parameter which influences fault seal. On the basis of the above studies, three systems of hydrocarbon migration and accumulation, as well as a pool-forming model are established for the gentle slope belt of the HuiMin depression, which can be applied for the prediction of regular patterns of oil-gas migration. Under guidance of the pool-forming geological model for the HuiMin slope belt, and taking seismic facies technology, log constraint evolution technology, pattern recognition of multiple parameter reservoir and discrimination technology of oil-bearing ability, this paper develops a set of methods and technologies suited to oil reservoir prediction of the gentle slope belt. Good economic benefit has been obtained.

吐哈盆地山前带构造岩相带及油气藏预测研究

This paper based on the example of mountain front tectonic belt of Tuha basin - a typical basin in west China, using geological, logging and seismic data, combining the two methods-comprehensive analysis of geological-geophysical data and numerical simulation together, studies the types of tectonic lithofacies and the mechanism of oil/gas accumulation in mountain front tectonic belt, and predicts favorable exploration areas. The tectonic lithofacies in periphery belt of compressional basin is systematically studied for the first time. The distribution and systematically analyzed with geological, logging and seismic data; the bury history of formations in the mountain front are restored with the back-stripping technique; the tectonic depression history of the mountain front is studied according to Airy Balanced Model; the tectonic evolution history is restored with the balanced section technique; according to the space composition of tectonic units and sedimentary systems of different geological time, the tectonic facies belt of the middle and lower Jurassic in the piedmont is divided into 12 types, and the controls of each type's tectonic lithofacies belt on the conditions of oil/gas generation, reservation and sealing are analyzed in depth. 3D numerical simulation and analysis is applied to the tectonic stress field in the hydrocarbon reservoir-forming-period for the first time. Because of the complex evolution of mountain front of Tuha basin, 3D numerical simulation of tectonic stress field in the hydrocarbon reservoir-forming-period helps to study the magnitude of the maximum principal stress, the minimum principal stress and the shear stress, the range and distribution of the principal stress, and controls of the upwards factors on the oil/gas migration and accumulation. Through the study on the oil-controlling fault's evolution, sealing mechanism and sealing history, the coupling of two effects of the fault-passage and sealing screen for oil/gas migration can be defined. Using the basic principle of petroleum system analysis, the paper systematically studies the hydrocarbon reservoir-forming mechanism and the time-space matching of the factors that affect the formation of reservoir, such as the space matching of active oil/gas matching of the active period of fault, the migration period of oil/gas and the formation period of trap. Through comprehensive analysis, the favorable exploration targets are selected in selected in the mountain front.

鄂尔多斯盆地西缘中生代构造与地层分析及盆地演化研究

Through the detailed analyses of Mesozoic tectono-stratigraphy and basin formation dynamic mechanism and the styles of different units in the western margin of Ordos Basin(Abbreviated to "the western margin"), while some issues of the pre-Mesozoic in the western margin and central part of Ordos Basin also be discussed, the main views and conclusion as follows: 1. There are three types of depositional systems which are related with syndepositional tectonic actions and different tectonic prototype basins, including: alluvial fan systems, river system (braided river system and sinuosity river system), lacustrine-river delta system and fan delta system. They have complex constitutions of genetic facies. For the tectonic sequence VI, the fan sediments finning upper in the north-western margin and coarse upper in the south-western margin respectively. 2. In order to light the relationship between basin basement subsidence rate and sediment supply and the superposed styles, five categories of depositional systems tracts in different prototype basins were defined: aggrading and transgressive systems tracts during early subsidence stage, regressive and aggrading systems tracts during rapid subsidence, upper transgessive systems tracts during later subsidence stage. Different filling characteristics and related tectonic actions in different stages in Mesozoic period were discussed. 3. In order to determined the tectonic events of the provenance zones and provenance strata corresponding to basins sediments, according the clastics dispersal style and chemical analyses results of sediments in different areas, the provenance characteristics have been described. The collision stage between the "Mongolia block" and the north-China block may be the late permian; The sediments of Mesozoic strata in the north-western margin is mainly from the Alex blocks and north-Qilian Paleozoic orogeny, while the south-western margin from Qinling orogeny. The volcanic debris in the Yan'an Formation may be from the arc of the north margin of north-China block, although more study needed for the origin of the debris. The provenance of the Cretaceous may be from the early orogeny and the metamorphic basement of Longshan group. 4. The subsidence curve and subsidence rate and sedimentary rate in different units have been analyzed. For different prototype basin, the form of the subsidence curves are different. The subsidence of the basins are related with the orogeny of the basins.The beginning age of the foreland basin may be the middle Triassic. The change of basement subsidence show the migration of the foredeep and forebulge into the basin. The present appearance of the Ordos basin may be formed at the late stage of Cretaceous, not formed at the late Jurassic. 5. The structure mode of the west margin is very complex. Structure transfer in different fold-thrust units has been divided into three types: transfer faults, transition structures and intersected form. The theoretic explanations also have been given for the origin and the forming mechanism. The unique structure form of Hengshanpu is vergent west different from the east vergence of most thrust faults, the mechanism of which has been explained. 6. In Triassic period, the He1anshan basin is extensional basin while the Hengshanbu is "forland", and the possible mechanism of the seemingly incompatible structures has been explained. First time, the thesis integrate the Jurassic—early Cretaceous basins of west margin with the Hexi corridor basins and explain the unitive forming mechanism. The model thinks the lateral extrusion is the main mechanism of the Hexi corridor and west margin basins, meanwhile, the deep elements and basement characters of the basins. Also, for the first time, we determine the age of the basalt in Helanshan area as the Cretaceous period, the age matching with the forming of the Cretaceous basins and as the main factor of the coal metamorphism in the Helanshan area. 7. The Neoprotterozoic aulacogen is not the continuation of the Mesozoic aulacogen, while it is another new rift stage. In the Paleozoic, the Liupanshan—southern Helanshan area is part of the back-arc basins of north Qilian ocean. 8. The Helanshan "alacogen" is connected with the north margin of north China block, not end at the north of Zhouzishan area like "appendices". Also, I think the upper Devonian basin as the beginning stage of the extensional early Carboniferous basins, not as a part of the foreland basins of Silurian period, not the collision rift. 9. The controlling factor of the difference of the deformation styles of the north-west margin and the south-west margin is the difference of the basements and adjacent tectonic units of the two parts.

东营凹陷下第三系岩性油气藏形成条件与预测

The Dongying depression, located in the northern part of the jiyang Sag in the Buohaiwan Basin, comprises one of the major oil-producing bases of the Shengli oil-field. The prediction and exploration of subtle or litho1ogical oil traps in the oil-field has become the major confronted target. This is also one of the frontier study areas in the highly-explored oil-bearing basins in East China and abroad. Based on the integrated analysis of the geological, seismic and logging data and the theories of sequence stratigraphy, tectono-stratigraphy and petroleum system, the paper has attempted to document the characteristics of the sequence stratigraphic and structural frameworks of the low Tertiary, the syndepositional faults and their control on deposition, and then to investigate the forming conditions and distribution of the tithological oil traps in the depression. The study has set up a set of analysis methods, which can be used to effectively analysis the sequence stratigraphy of inland basins and predict the distribution of sandstone reservoirs in the basins. The major achievements of the study are as follows: 1. The low Tertiary can be divided into 4 second-order sequences and 13 third-order sequences, and the systems tracts in the third-order sequences have been also identified based on the examination and correction of well logging data and seismic profiles. At the same time, the parasequences and their stacking pattern in the deltaic systems of the third member of the Shahejie Formation have been recognized in the key study area. It has been documented that the genetic relation of different order sequences to tectonic, climatic and sediment supply changes. The study suggested that the formation of the second-order sequences was related to multiple rifting, while the activity of the syndepositional faults controlled the stacking pattern of parasequences of the axial deltaic system in the depression. 2. A number of depositional facies have been recognized in the low Tertiary on the basis of seismic facies and well logging analysis. They include alluvial fan, fan delta or braided delta, axial delta, lowstand fan, lacustrine and gravity flow deposits. The lacustrine lowstand fan deposits are firstly recognized in the depression, and their facies architecture and distribution have been investigated. The study has shown that the lowstand fan deposits are the important sandstone reservoirs as lithological oil traps in the depression. 3. The mapping of depositional systems within sequences has revealed the time and special distrbution of depositional systems developed in the basin. It is pointed out that major elastic systems comprise the northern marginal depositional systems consisting of alluvial fan, fan delta and offshore lowstand fan deposits, the southern gentle slope elastic deposits composed of shallow lacustrine, braided delta and lowstand fan deposits and the axial deltaic systems including those from eastern and western ends of the depression. 4. The genetic relationship between the syndepositional faults and the distribution of sandstones has been studied in the paper, upper on the analysis of structural framework and syndepositional fault systems in the depression. The concept of structural slope-break has been firstly introduced into the study and the role of syndepositional faults controlling the development of sequence architecture and distribution of sandstones along the hinged and faulted margins have been widely investigated. It is suggested that structural styles of the structural slope-break controlled the distribution of lowstand fan deposits and formed a favorable zone for the formation of lithological or structure-lithological oil traps in the basin. 5. The paper has made a deep investigation into the forming condition and processes of the lithological traps in the depression, based the analysis of composition of reservoir, seal and resource rocks. It is pointed out that there were two major oil pool-forming periods, namely the end of the Dongying and Guangtao periods, and the later one is the most important. 6. The study has finally predicted a number of favorable targets for exploration of lithologieal traps in the depression. Most of them have been drilled and made great succeed with new discovered thousands tons of raw oil reserves.

火成岩储层裂缝识别、预测理论与方法研究－以济阳坳陷火成岩油藏为例

Since 1970s, igneous reservoirs such as Shang741, Bin674 and Luol51 have been found in Jiyang depression, which are enrichment and heavy-producing. Showing good prospect of exploration and development, igneous reservoirs have been the main part of increasing reserves and production in Shengli oilfield. As fracture igneous reservoir being an extraordinary complex concealed reservoir and showing heavy heterogeneity in spatial distribution, the study of recognition, prediction, formation mechanism and the law of distribution of fracture is essential to develop the reservoir. Guided by multiple discipline theory such as sedimentology, geophysics, mineralogy, petroleum geology, structural geology and reservoir engineering, a set of theories and methods of recognition and prediction of fractured igneous rock reservoir are formed in this paper. Rock data, three-dimensional seismic data, log data, borehole log data, testing data and production data are combined in these methods by the means of computer. Based on the research of igneous rock petrography and reservoir formation mechanism, emphasized on the assessment and forecast of igneous rock reservoir, aimed at establishing a nonhomogeneity quantification model of fractured igneous rock reservoir, the creativity on the fracture recognition, prediction and formation mechanism are achieved. The research result is applied to Jiyang depression, suggestion of exploration and development for fractured igneous rock reservoir is supplied and some great achievement and favourable economic effect are achieved. The main achievements are gained as follows: 1. The main facies models of igneous rock reservoir in JiYang depression are summarized. Based on data and techniques of seism, well log and logging,started from the research of single well rock facies, proceeded by seismic and log facies research, from point to line and line to face, the regional igneous facies models are established. And hypabyssal intrusion allgovite facies model, explosion volcaniclastic rock facies model and overfall basaltic rocks facies model are the main facies models of igneous rock reservoir in JiYang depression. 2. Four nonhomogenous reservoir models of igneous reservoirs are established, which is the base of fracture prediction and recognition. According to characteristics of igneous petrology and spatial types of reservoir, igneous reservoirs of Jiyang depression are divided into four categories: fractured irruptive rock reservoir, fracture-pore thermocontact metamorphic rock and irruptive rock compound reservoir, pore volcanic debris cone reservoir and fracture-pore overfall basaltic rock reservoir. The spatial distribution of each model's reservoir has its features. And reservoirs can be divided into primary ones and secondary ones, whose mechanism of formation and laws of distribution are studied in this paper. 3. Eight geologic factors which dominate igneous reservoirs are presented. The eight geologic factors which dominates igneous reservoirs are igneous facies, epigenetic tectonics deformation, fracture motion, intensity of intrusive effect and adjoining-rock characters, thermo-contact metamorphic rock facies, specific volcano-tectonic position, magmatic cyclicity and epigenetic diagenetic evolution. The interaction of the eight factors forms the four types nonhomogenous reservoir models of igneous reservoirs in Jiyang depression. And igneous facies and fracture motion are the most important and primary factors. 4. Identification patterns of seismic, well log and logging facies of igneous rocks are established. Igneous rocks of Jiyang depression show typical reflecting features on seismic profile. Tabular reflection seismic facies, arc reflection seismic facies and hummocky or mushroom reflection seismic facies are the three main facies. Logging response features of basic basalt and diabase are shown as typical "three low and two high", which means low natural gamma value, low interval transit-time, low neutron porosity, high resistivity and high density. Volcaniclastic rocks show "two high and three low"-high neutron porosity, high interval transit-time, low density, low-resistance and low natural gamma value. Thermo-contact metamorphic rocks surrounding to diabase show "four high and two low" on log data, which is high natural gamma value, high self-potential anomaly, high neutron porosity, high interval transit-time and low density and low-resistance. Based on seismic, well log and logging data, spatial shape of Shang 741 igneous rock is described. 5. The methods of fracture prediction and recognition for fractured igneous reservoir are summarized. Adopting FMI image log and nuclear magnetic resonance log to quantitative analysis of fractured igneous reservoir and according to formation mechanism and shape of fracture, various fractures are recognized, such as high-angle fracture, low-angle fracture, vertical fracture, reticulated fracture, induced fracture, infilling fracture and corrosion vug. Shang 741 intrusive rock reservoir can be divided into pore-vug compound type, pore fracture type, micro-pore and micro-fracture type. Physical properties parameters of the reservoir are computed and single-well fracture model and reservoir parameters model are established. 6. Various comprehensive methods of fracture prediction and recognition for fractured igneous reservoir are put forward. Adopting three-element (igneous facies, fracture motion and rock bending) geologic comprehensive reservoir evaluation technique and deep-shallow unconventional laterolog constrained inversion technique, lateral prediction of fractured reservoir such as Shang 741 is taken and nonhomogeneity quantification models of reservoirs are established.