Cutting of Frozen Wood

The objective of this master's thesis was to develop a system for measuring the cutting forces of frozen wood. In northern parts of the world cuttingof frozen wood is one of the major problem. During winter and early spring the temperature inside the wood cells will fall below Zero degrees that strongly influences on the properties of the wood. These variations of properties will effects on the blade nomenclature while cutting the frozen wood. However the end results will cause uneven cutting forces. Cutting forces, Chip formation, wearing of the blade and the quality of the machined surface are difficult task. In this project we are attempting to find the variation of cutting forces and properties of frozen wood at four different temperatures (-20 , -10, 0 and + 10 degrees). The linear planning machine was used for measuring the cuttingforces. The cutting was done parallel to the long axis of wood due to the nature of pine wood and the structure of the plane. A considerable amount of work andtime was used for collecting and processing the numerical information from the sensors of the measuring system. There were some alterations suggested to the construction of the plane and the sensor system.

A Feasibility Study of a Pelleting Plant as an Option for By Product Upgrading in Wood-Processing Industry

Tämän kannattavuustutkimuksen lähtökohtana oli se, että Yhtyneet Sahat Oy:n Kaukaan sahalla ja Luumäen jatkojalostuslaitoksella haluttiin selvittää pellettitehtaan kannattavuus nykyisessä markkinatilanteessa. Tämä työon luonteeltaan teknis-taloudellinen selvitys eli ns. feasibility study. Pelletöintiprosessi on tekniikaltaan yksinkertainen eikä edellytä korkea teknologian laitteita. Toimiala on maailmanlaajuisesti varsin uusi. Suomessa pellettimarkkinat ovat vielä pienet ja kehittymättömät, mutta kasvua on viime vuosina tapahtunut. Valtaosa kotimaan tuotannosta menee vientiin. Investoinnin laskentaprosessissa saadut tuotannon alkuarvot sekä kustannusrakenteen määrittelyt ovat perustana varsinaisille kannattavuuslaskelmille. Laskelmista on selvitetty investointeihin liittyvät yleisimmät taloudelliset tunnusluvut ja herkimpiä muuttujia on tutkittu ja pohdittu herkkyysanalyysiä apuna käyttäen.

Investments and value creation Case pulp and paper industry

Tämä tutkimus analysoi 49 sellu- ja paperiteollisuusyrityksen investointistrategioiden ja yrityksen arvon välistä yhteyttä vuosien 1996 ja 2005 välillä. Teoriaosa luo katsauksen arvonmääritysmenetelmiin ja investointien vaikutuksesta yrityksen arvoon ja arvonluontiin. Empiirinen osa on sekä kuvaileva, että selittävä. Yrityksen arvon kehittyminen mitataan vuosittain lisäarvomallilla (EVA®). Toteutetussa analyysissa yritykset on ryhmiteltyjoko liiketoimintaorientaation tai maantieteellisen alueen mukaan. Yritysten investointistrategiat jaoteltiin kasvumallin mukaisesti T&K:hon käyttöomaisuusinvestointeihin ja yritysostoihin. Kasvumallin tulokset ovat raportoitu yritystasolla. Tulokset osoittavat, että harvat sellu- ja paperiteollisuusyritykset ovetpystyneet arvonluontiin. Arvonluonti riippuu merkittävästi talouden suhdanteista. Yritysten investointistrategiat ovat olleet hyvin identtisiä tarkastelujaksonaikana ja alan suurimpien yritysten investointistrategiat kuvaavat hyvin koko toimialan kehitystä. Pienempien yritysten investointistrategiat eroavat valtavirran toimista. Jatkoanalyysi osoitti, että investoinnit käyttöomaisuuteen parantavat kannattavuutta, mitattuna EBITDA-%:lla ja yritysostot heikentävät sitä. Mitattaessa arvonluontia EVA®:lla käyttöomaisuusinvestoinneilla on positiivinen vaikutus arvonluontiin, kun taas yritysostot tuhoavat arvoa. Havainnot tukevat aikaisempia empiirisiä tutkimustuloksia.

The Boundaries of a Firm in the Pulp and Paper Industry: Complementarities of the Resource-Based View and Transaction Cost Economics

Tämän tutkimuksen tarkoituksena on tutkia sellu- ja paperiteollisuuden toimintojen luonnetta sekä miten yrityksen rajapinnat ovat muodostuneet ko. teollisuudenalalla. Tutkimus on eksploratiivinen ja luonteeltaan kvalitatiivinen. Tutkimuksen aineisto kerättiin yrityksissä tehdyillä teemahaastatteluilla. Sellu- ja paperitehtaan toimintojen analysoinnissa käytetään resurssiperusteista näkemystä ja transaktiokustannusteoriaa. Tutkimuksen yritysten rakennetta voidaan pitää varsin konservatiivisena. Teoreettinen kehys pystyi selittämään varsinaisen tuotannon järjestämistä varsin hyvin. Tukitoiminnoissa löytyi ristiriitoja teorian ja todellisuuden välillä. Tuotantotoiminnot kannattaa pitää yrityksen sisällä, koska ne täyttävät VRIN-attribuutit ja niihin liittyy korkeita transaktiokustannuksia. Suurin osa tukitoiminnoista voidaan luokitella triviaaleiksi. Joitain tukitoimintoja voidaan kuitenkin luokitella strategisesti tärkeiksi, ja voidaan päätellä, että ne pitäisi pitää yrityksen sisällä. Tässä suhteessa tulokset olivat kuitenkin ristiriitaisia, ja lisätutkimuksia tarvittaisiin lopullisten johtopäätösten tekemiseen.

The Reflections of Strategic Orientation on profitability - A resource-based study in pulp and paper industry

Tutkielman tavoitteena oli analysoida erilaisia strategisia orientaatioita sellu- ja paperiteollisuudessa. Sellu- ja paperiteollisuus on kohtaamassa strategisia haasteita, jotka ulottuvat syvälle sen rakenteisiin. Yritykset ovat valinneet erilaisia lähestymistapoja organisoidessaan tuotantoa ja kansainvälistä arvoketjuaan tässä muuttuvassa ympäristössä. Tutkimukseen valittiin 30 suurinta sellu- ja paperiteollisuudessa toimivaa yritystä ja mahdollisia syitä kannattavuuseroihin yritysten välillä analysoitiin. Yritysten strategista orientaatiota tarkasteltiin vertailemalla muun muassa seuraavia tekijöitä: vertikaalinen integraatioaste, tuotevalikoiman laajuus, tuotantokapasiteetin levinneisyys ja tuotantokapasiteetin ikä. Kannattavuutta mitattiin erilaisilla talouden tunnusluvuilla (liikevoitto, oman pääoman tuotto-%, koko pääoman tuotto-%). Tulosten mukaan yrityksiä voidaan ryhmitellä strategisen orientaation perusteella ja ryhmien välillä on kannattavuuseroja.

Financial Analysis of the Pulp and Paper Industry: Performance and value creation of the world's pulp and paper companies

Tutkimuksen tavoitteena on analysoida 74 sellu- ja paperiyrityksen taloudellista suorituskykyä kannattavuutta, maksuvalmiutta, vakavaraisuutta ja arvonluontikykyä kuvaavilla tunnusluvuilla. Tutkimuksen teoriaosa esittelee liiketoiminta-analyysin välineet, jonka jälkeen esitellään taloudelliset tunnusluvut. Empiriaosassa käydään läpi vuoden 2005 tunnusluvut yritystasolla. Jotta voidaan tarkastella tunnuslukujen muutoksia pitkällä aikavälillä, yritykset ryhmitellään maantieteellisen sijainnin sekä liiketoimintaorientaation mukaan. Tutkimus on kuvaileva. Tunnusluvuista voidaan todeta sellu- ja paperiteollisuudessa meneillään oleva toimialan rakennemuutos. Eteläamerikkalaiset yritykset, jotka hyötyvät uudesta ja kustannustehokkaasta raaka-aineesta, ovat siirtyneet lähemmäs arvonluontia, kun taas suurin osa pohjoisamerikkalaisista yrityksistä, jotka olivat toimialan johtavia arvonluojia, ovat nyt arvon tuhoajia. Toimiala kärsii myös alhaisesta kannattavuudesta, joka vaikuttaa eniten pohjoisamerikkalaisiin yrityksiin. Samaan aikaan eteläamerikkalaiset yritykset ovat nostaneet kannattavuuttaan, mikä puolestaan korostaa meneillään olevaa muutosta.

The effect of oxygen delignification on fiber properties in kraft pulp production - a review

Fiber damages comprise fiber deformations, characterized as fiber curl, kink, dislocations and strength losses as well as some yet unidentified factors. This recently discovered phenomenon is especially evident in mill scale kraftpulps. Laboratory produced pulps tend to have less damages and superior strength properties compared to those produced in pulp mills. Generally fiber damages pose a problem in the production of reinforcement pulp because they tend to decrease the ability of fibers to transmit load. Previous studies on fiber damage have shown that most of the fiber damages occur during brown stock processing starting from cooking and discharging. This literature review gives an overall picture on fiber damages occurring during softwood kraft pulp production with an emphasis on the oxygen delignification stage. In addition the oxygen delignification stage itself is described in more detailed extent in order to understand the mechanisms behind the delignification and fiber damaging effect. The literature available on this subject is unfortunately quite contradictory and implicates a lotof different terms. Only a few studies have been published which help to understand the nature of fiber damages. For that reason the knowledge presented in this work is not only based on previous studies but also on research scientist and mill staff interviews.

Aspects on Process Engineering in the Finnish Pulp and Paper Industry : Thesis for the Degree of Licentiate in Science of Technology

Process development will be largely driven by the main equipment suppliers. The reason for this development is their ambition to supply complete plants or process systems instead of single pieces of equipment. The pulp and paper companies' interest lies in product development, as their main goal is to create winning brands and effective brand management. Design engineering companies will find their niche in detail engineering based on approved process solutions. Their development work will focus on increasing the efficiency of engineering work. Process design is a content-producing profession, which requires certain special characteristics: creativity, carefulness, the ability to work as a member of a design team according to time schedules and fluency in oral as well as written presentation. In the future, process engineers will increasingly need knowledge of chemistry as well as information and automation technology. Process engineering tools are developing rapidly. At the moment, these tools are good enough for static sizing and balancing, but dynamic simulation tools are not yet good enough for the complicated chemical reactions of pulp and paper chemistry. Dynamic simulation and virtual mill models are used as tools for training the operators. Computational fluid dynamics will certainlygain ground in process design.

Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Determination of thermal diffusivity in papaya pulp as a function of maturation stage

In order to determine the penetration of the thermal wave in the papaya fruit pulp (Carica papaya L.), cv. Golden, thermal diffusivity of the pulp was obtained measuring temperature at four different depths. Measurements were carried out initially with the fruit on the first stage of maturity. The changes of the thermal diffusivity were expressed as a function of ripening. A temporal decrease of the thermal diffusivity was observed. Chemical (pH, soluble solids and total titratable acidity) and physical (pulp firmness) properties were measured as well and the results were compared to the thermal diffusivity change.

Short communication.Wood identification based on their common name and their transversal surface anatomy. Application to the batch from the expedition of Ruiz and Pavon

Aim of study: To identify species of wood samples based on common names and anatomical analyses of their transversal surfaces (without microscopic preparations). Area of study: Spain and South America Material and methods: The test was carried out on a batch of 15 lumber samples deposited in the Royal Botanical Garden in Madrid, from the expedition by Ruiz and Pavon (1777-1811). The first stage of the methodology is to search and to make a critical analysis of the databases which list common nomenclature along with scientific nomenclature. A geographic filter was then applied to the information resulting from the samples with a more restricted distribution. Finally an anatomical verification was carried out with a pocket microscope with a magnification of x40, equipped with a 50 micrometers resolution scale. Main results: The identification of the wood based exclusively on the common name is not useful due to the high number of alternative possibilities (14 for “naranjo”, 10 for “ébano”, etc.). The common name of one of the samples (“huachapelí mulato”) enabled the geographic origin of the samples to be accurately located to the shipyard area in Guayaquil (Ecuador). Given that Ruiz y Pavon did not travel to Ecuador, the specimens must have been obtained by Tafalla. It was possible to determine correctly 67% of the lumber samples from the batch. In 17% of the cases the methodology did not provide a reliable identification. Research highlights: It was possible to determine correctly 67% of the lumber samples from the batch and their geographic provenance. The identification of the wood based exclusively on the common name is not useful.

Enzymatic technology to improve oil extraction from Caryocar brasiliense camb. (Pequi) Pulp.

The present study aims to compare yield and quality of pequi pulp oil when applying two distinct processes: in the first, pulp drying in a tray dryer at 60ºC was combined with enzymatic treatment and pressing to oil extraction; in the second, a simple process was carried out by combining sun-drying pulp and pressing. In this study, raw pequi fruits were collected in Mato Grosso State, Brazil. The fruits were autoclaved at 121ºC and stored under refrigeration. An enzymatic extract with pectinase and CMCase activities was used for hydrolysis of pequi pulp, prior to oil extraction. The oil extractions were carried out by hydraulic pressing, with or without enzymatic incubation. The oil content in the pequi pulp (45% w/w) and the physicochemical characteristic of the oil was determined according to standard analytical methods. Free fatty acids, peroxide values, iodine and saponification indices were respectively 1.46 mgKOH/g, 2.98 meq/kg, 49.13 and 189.40. The acidity and peroxide values were lower than the obtained values in commercial oil samples, respectively 2.48 mgKOH/g and 5.22 meq/kg. Aqueous extraction has presented lower efficiency and higher oxidation of unsaturated fatty acids. On the other hand, pequi pulp pressing at room temperature has produced better quality oil. However its efficiency is still smaller than the combined enzymatic treatment and pressing process. This combined process promotes cellular wall hydrolysis and pulp viscosity reduction, contributing to at least 20% of oil yield increase by pressing.

Anaerobic treatment of deinking pulp plant effluents

Anaerobic treatment as a first biological stage in wastewater treatment is nowadays a well-established technology in recycled paper processing mills using closed water circuits. Today further developed high-rate processes and especially high-tower reactors are also able to handle lower organic loads and become therefore feasible for deinking pulp plant effluents. The interest in the anaerobic method is based on a positive energy balance in form of biogas production and low biomass yield from the process. The anaerobic treatment method was researched and its suitability for the deinking pulp plant effluents was tested experimentally at Stora Enso Maxau mill. In the theory, the deinking pulp process is introduced and the effluents from the deinking process are characterized. The anaerobic treatment is brought up in depth in terms of its use for the deinking effluents, and different kind of reactor types are presented. In addition, other wastewater treatment methods are shortly introduced with the focus on tertiary treatment. Static biodegradability tests were carried out for the wastewaters both anaerobically and aerobically. Based on the results, the deinking effluents can be degraded anaerobically, and inhibition to the methanogenic bacteria was not noticed. In the aerobic static test a good performance of the existing wastewater treatment plant at Maxau mill was proved. Later on pilot trials with sequential anaerobic-aerobic treatment were carried out for the deinking effluents. The anaerobic reactor used was a so called internal circulation reactor. The results confirmed that the combination of the anaerobic treatment and the aerobic activated sludge process is a suitable method for deinking wastewaters with a COD reduction as good as with a two stage aerobic method. When combined with the outstanding quality of the produced biogas and the cost savings acquired from the lower sludge production, the anaerobic treatment was found to be an especially favorable treatment method.