A study on the inhibition of mild steel corrosion in hydrochloric acid by pyridoxol hydrochloride

The inhibition of the corrosion of mild steel in 2M hydrochloric acid solutions by Pyridoxol hydrochloride (PXO) has been studied using weight loss and hydrogen evolution techniques. The inhibitor (PXO) exhibited highest inhibition efficiency of 71.93% at the highest inhibitor concentration of 1.0 x 10-2M investigated and a temperature of 303K from weight loss result. Also, inhibition was found to increase with increasing concentration of the inhibitor and decreasing temperature. A first order type of mechanism has been deduced from the kinetic treatment of the weight loss results and the process of inhibition attributed to physical adsorption. The results obtained from the two techniques show that pyridoxol hydrochloride could serve as an effective inhibitor of the corrosion of mild steel in HCl acid solution. The compound obeys the Langmuir adsorption isotherm equation.

Numerical Investigation of Flow Past a Circular Cylinder and in a Staggered Tube Bundle Using Various Turbulence Models

Transitional flow past a three-dimensional circular cylinder is a widely studied phenomenon since this problem is of interest with respect to many technical applications. In the present work, the numerical simulation of flow past a circular cylinder, performed by using a commercial CFD code (ANSYS Fluent 12.1) with large eddy simulation (LES) and RANS (κ - ε and Shear-Stress Transport (SST) κ - ω! model) approaches. The turbulent flow for ReD = 1000 & 3900 is simulated to investigate the force coefficient, Strouhal number, flow separation angle, pressure distribution on cylinder and the complex three dimensional vortex shedding of the cylinder wake region. The numerical results extracted from these simulations have good agreement with the experimental data (Zdravkovich, 1997). Moreover, grid refinement and time-step influence have been examined. Numerical calculations of turbulent cross-flow in a staggered tube bundle continues to attract interest due to its importance in the engineering application as well as the fact that this complex flow represents a challenging problem for CFD. In the present work a time dependent simulation using κ – ε, κ - ω! and SST models are performed in two dimensional for a subcritical flow through a staggered tube bundle. The predicted turbulence statistics (mean and r.m.s velocities) have good agreement with the experimental data (S. Balabani, 1996). Turbulent quantities such as turbulent kinetic energy and dissipation rate are predicted using RANS models and compared with each other. The sensitivity of grid and time-step size have been analyzed. Model constants sensitivity study have been carried out by adopting κ – ε model. It has been observed that model constants are very sensitive to turbulence statistics and turbulent quantities.

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

Product costing model for laser welded hollow core steel panels

The aim of the study was to create an easily upgradable product costing model for laser welded hollow core steel panels to help in pricing decisions. The theory section includes a literature review to identify traditional and modern cost accounting methodologies, which are used by manufacturing companies. The theory section also presents the basics of steel panel structures and their manufacturing methods and manufacturing costs based on previous research. Activity-Based costing turned out to be the most appropriate methodology for the costing model because of wide product variations. Activity analysis and the determination of cost drivers based on observations and interviews were the key steps in the creation of the model. The created model was used to test how panel parameters affect the costs caused by the main manufacturing stages and materials. By comparing cost structures, it was possible to find the panel types that are the most economic and uneconomic to manufacture. A sensitivity analysis proved that the model gives sufficiently reliable cost information to support pricing decisions. More reliable cost information could be achieved by determining the cost drivers more accurately. Alternative methods for manufacturing the cores were compared with the model. The comparison proved that roll forming can be more advantageous and flexible than press brake bending. However, more extensive research showed that roll forming is possible only when the cores are designed to be manufactured by roll forming. Due to that fact, when new panels are designed consideration should be given to the possibility of using roll forming.

Customer consciousness in the production process of a steel factory

The purpose of this thesis is to examine the level of customer consciousness of the production process employees in a steel factory and to investigate the methods of internal marketing in order to propose development practices to enhance the customer consciousness of the case company employees. The significance of the level of customer consciousness is discussed and practices already implemented affecting the level of customer consciousness in the company are examined. The literature review gives an insight to the role of customer consciousness in the CRM philosophy of a manufacturing company and examines the means of internal marketing in enhancing customer consciousness. In the empirical part of the study, the level and significance of customer consciousness is determined by conducting individual and focus group interviews. The interviews are also used to examine the practices that could function in enhancing the customer consciousness of the employees. Development suggestions to improve the level of customer consciousness in the production process are given based on the results. The level of customer consciousness is at a poor level in the production process and influences above all on work motivation and job satisfaction, but possibly on customer satisfaction as well. The enhancement of customer consciousness in the production process should be done e.g. by ensuring the distribution of right knowledge coherently to all of the employees, gathering large customer reference database to exploit in work and in training, using visual illustration in presenting the customer information, training proactively and letting the employees to participate in the customer oriented development activities. Customer satisfaction focused reward system can be considered.

In vitro effect of substrate, temperature and photoperiod on Phakopsora pachyrhizi urediniospore germination and germ tube growth

In vitro experiments were conducted to assess the effects of substrate, temperature and time of exposure to temperature and photoperiod on P. pachyrhizi uredospore germination and germ tube growth. The following substrates were tested: water-agar and soybean leaf extract-agar at different leaf concentrations (0.5, 1.0, 2.0 and 4.0 g of leaves and 15g agar/L water), temperatures (10, 15, 20, 25, 30, and 35oC) and times of exposure (1, 2, 3, 4, 5, 6, 7, and 8 hours) to temperature and 12 different photoperiods. The highest germination and germ tube length was found for the soybean leaf extract agar. Maximum P. pachyrhizi uredospore germination was obtained at 21.8 and 22.3°C, and maximum germ tube growth at 21.4 and 22.1°C. The maximum uredospore germination was found at 6.4 hours exposure, while the maximum germ tube length was obtained at 7.7 h exposure. Regarding photoperiod, the maximum spore germination and the maximum uredospore germ tube length were found in the dark. Neither spore germination nor uredospore germ tube growth was completely inhibited by the exposure to continuous light.

Miehistönkuljetusajoneuvon rungon suunnittelu

Tämän diplomityön tavoitteena oli suunnitella miehistönkuljetusajoneuvon runko. Rungosta suunniteltiin mahdollisimman hyvin energiaa absorboiva. Rakenne toteutettiin kennora-kenteena. Suunnittelussa sovellettiin koneensuunnittelun periaatteiden lisäksi energiaa ab-sorboivien rakenteiden suunnittelun periaatteita. Myös valmistustekniset näkökohdat otet-tiin huomioon. Rakenteessa hyödynnettiin Ruukki Oy:n Ramor 500 suojausterästä sekä OPTIM 500 MC terästä. Lisäksi erilaisten täyteaineiden käyttöä tutkittiin. Suunnittelun työkaluna käytettiin epälineaarista elementtimenetelmää, koska energiaa ab-sorboivien rakenteiden suunnittelussa on otettava huomioon materiaalien epälineaarinen käyttäytyminen. Rakenteen suunnittelu jakaantui viiteen vaiheeseen. Aluksi rakenteeseen kohdistuvat kuormitukset laskettiin elementtimenetelmän avulla. Esisuunnittelussa lasket-tiin plastisuusteorian avulla alustavasti tarvittavat materiaalipaksuudet. Tämän jälkeen ra-kenteen ydingeometria optimoitiin mahdollisimman hyvin energiaa absorboivaksi. Opti-moinnissa hyödynnettiin elementtimenetelmää. Seuraavassa vaiheessa varmistettiin raken-teen globaalit ominaisuudet. Lopuksi rakenteen kestävyyttä tarkasteltiin elementtimene-telmällä. Runko ei mallien mukaan kestänyt siltä vaadittuja kuormitustapauksia. Mallin kaikki ole-tukset pidettiin varmalla puolella. Reunaehdot oletettiin todellisuutta jäykemmiksi. Myös-kään materiaalin venymänopeudesta johtuvaa lujittumista ei otettu huomioon. Koska mii-naräjähdys on monimutkainen tapahtuma, rungon todellinen kestävyys joudutaan ar-viomaan räjähdystesteillä. Elementtimallien perusteella voidaan kuitenkin sanoa, että ener-giaa absorboiva ajoneuvon runko on mahdollista toteuttaa kennorakenteena. Lisäksi voi-daan todeta, että elementtimenetelmää sopii työvälineeksi tämän tyyppisten rakenteiden suunnitteluun.

Internal ambience of bee colonies submitted to strengthening management by adding broods

This study aimed to investigate the ideal brood area to be introduced for strengthening Apis mellifera colonies, considering variations in the hive's internal ambience. Therefore, eight colonies were equipped with data loggers for recording variations in temperature and humidity inside the hives. Then, these colonies were split in four treatments involving the swapping of four, three, two and one brood comb between strong and weak colonies. Growth in the amount of brood and food stores to the four colony strengthening treatments was assessed counting the comb cells to record changes in the brood and food area. The colonies tended to restore their normal thermoregulation within four hours after they had been manipulated and the hive cover had been closed, which quickly increased brood area in the receiving colonies. Results showed that adding up to three brood combs constitute an important alternative for strengthening Apis mellifera colonies because it did not interfere with nest thermoregulation, speeded up population growth in weak colonies and did not affect the development of strong colonies.

The impact of a chest tube management protocol on the outcome of trauma patients with tube thoracostomy

ABSTRACTObjective:to investigate the effect of standardized interventions in the management of tube thoracostomy patients and to assess the independent effect of each intervention.Methods:A chest tube management protocol was assessed in a retrospective cohort study. The tube thoracostomy protocol (TTP) was implemented in August 2012, and consisted of: antimicrobial prophylaxis, chest tube insertion in the operating room (OR), admission post chest tube thoracostomy (CTT) in a hospital floor separate from the emergency department (ED), and daily respiratory therapy (RT) sessions post-CTT. The inclusion criteria were, hemodynamic stability, patients between the ages of 15 and 59 years, and injury severity score (ISS) < 17. All patients had isolated injuries to the chest wall, lung, and pleura. During the study period 92 patients were managed according to the standardized protocol. The outcomes of those patients were compared to 99 patients treated before the TTP. Multivariate logistic regression analysis was performed to assess the independent effect of each variable of the protocol on selected outcomes.Results:Demographics, injury severity, and trauma mechanisms were similar among the groups. As expected, protocol compliance increased after the implementation of the TTP. There was a significant reduction (p<0.05) in the incidence of retained hemothoraces, empyemas, pneumonias, surgical site infections, post-procedural complications, hospital length of stay, and number of chest tube days. Respiratory therapy was independently linked to significant reduction (p<0.05) in the incidence of seven out of eight undesired outcomes after CTT. Antimicrobial prophylaxis was linked to a significant decrease (p<0.05) in retained hemothoraces, despite no significant (p<0.10) reductions in empyema and surgical site infections. Conversely, OR chest tube insertion was associated with significant (p<0.05) reduction of both complications, and also significantly decreased the incidence of pneumonias.Conclusion:Implementation of a TTP effectively reduced complications after CTT in trauma patients.

Teaching project: a low-cost swine model for chest tube insertion training

Objective: to describe and evaluate the acceptance of a low-cost chest tube insertion porcine model in a medical education project in the southwest of Paraná, Brazil. Methods: we developed a low-cost and low technology porcine model for teaching chest tube insertion and used it in a teaching project. Medical trainees - students and residents - received theoretical instructions about the procedure and performed thoracic drainage in this porcine model. After performing the procedure, the participants filled a feedback questionnaire about the proposed experimental model. This study presents the model and analyzes the questionnaire responses. Results: seventy-nine medical trainees used and evaluated the model. The anatomical correlation between the porcine model and human anatomy was considered high and averaged 8.1±1.0 among trainees. All study participants approved the low-cost porcine model for chest tube insertion. Conclusion: the presented low-cost porcine model for chest tube insertion training was feasible and had good acceptability among trainees. This model has potential use as a teaching tool in medical education.

Surface transformation hardening of carbon steel with high power fiber laser

This study investigated the surface hardening of steels via experimental tests using a multi-kilowatt fiber laser as the laser source. The influence of laser power and laser power density on the hardening effect was investigated. The microhardness analysis of various laser hardened steels was done. A thermodynamic model was developed to evaluate the thermal process of the surface treatment of a wide thin steel plate with a Gaussian laser beam. The effect of laser linear oscillation hardening (LLOS) of steel was examined. An as-rolled ferritic-pearlitic steel and a tempered martensitic steel with 0.37 wt% C content were hardened under various laser power levels and laser power densities. The optimum power density that produced the maximum hardness was found to be dependent on the laser power. The effect of laser power density on the produced hardness was revealed. The surface hardness, hardened depth and required laser power density were compared between the samples. Fiber laser was briefly compared with high power diode laser in hardening medium-carbon steel. Microhardness (HV0.01) test was done on seven different laser hardened steels, including rolled steel, quenched and tempered steel, soft annealed alloyed steel and conventionally through-hardened steel consisting of different carbon and alloy contents. The surface hardness and hardened depth were compared among the samples. The effect of grain size on surface hardness of ferritic-pearlitic steel and pearlitic-cementite steel was evaluated. In-grain indentation was done to measure the hardness of pearlitic and cementite structures. The macrohardness of the base material was found to be related to the microhardness of the softer phase structure. The measured microhardness values were compared with the conventional macrohardness (HV5) results. A thermodynamic model was developed to calculate the temperature cycle, Ac1 and Ac3 boundaries, homogenization time and cooling rate. The equations were numerically solved with an error of less than 10-8. The temperature distributions for various thicknesses were compared under different laser traverse speed. The lag of the was verified by experiments done on six different steels. The calculated thermal cycle and hardened depth were compared with measured data. Correction coefficients were applied to the model for AISI 4340 steel. AISI 4340 steel was hardened by laser linear oscillation hardening (LLOS). Equations were derived to calculate the overlapped width of adjacent tracks and the number of overlapped scans in the center of the scanned track. The effect of oscillation frequency on the hardened depth was investigated by microscopic evaluation and hardness measurement. The homogeneity of hardness and hardened depth with different processing parameters were investigated. The hardness profiles were compared with the results obtained with conventional single-track hardening. LLOS was proved to be well suitable for surface hardening in a relatively large rectangular area with considerable depth of hardening. Compared with conventional single-track scanning, LLOS produced notably smaller hardened depths while at 40 and 100 Hz LLOS resulted in higher hardness within a depth of about 0.6 mm.

A Steel Company Entering the Market Area of St. Petersburg

Tutkimuksen tavoitteena on selvittää tarkoituksenmukaisin etabloitumismenetelmä teräsyhtiön kansainvälistymisessä Pietarin markkinoille. Vaikka kansainvälistymistä onkin tutkittu paljon, kyseisen kontekstin erityispiirteisiin on aiemmissa tutkimuksissa kiinnitetty vain vähän huomiota. Kansainvälistymisteorioista työhön valittiin John Dunningin eklektinen paradigma sekä Uppsala-malli. Etabloitumismenetelmän valintaa puolestaan tarkastellaan eri vaihtoehtojen kautta, jotka kattavat viennin, suorat ulkomaan investoinnit, sopimusjärjestelyt sekä yhteisyrityksen. Valintaa selitetään taustalla vaikuttavien tekijöiden sekä kansainvälistymisprosessin kautta. Kohteena olevan markkina-alueen potentiaalin, ongelmien sekä yrityksen kilpailuetujen arvioinnin jälkeen ehdotetaan optimaalista ratkaisua. Omat haasteensa operaatiomuodon valintaan luovat potentiaalinen mutta haastava kohdemarkkina-alue sekä yrityksen sisäiset tekijät. Kontekstiin parhaiten sopivaksi etabloitumismenetelmäksi esitetään aloittamista välittömällä viennillä asiakkaiden etsimiseksi ja suhteiden luomiseksi. Kun asiakkuuksia alueella on riittävästi, myyntikonttorin perustaminen Pietarin lähelle nähdään tarkoituksenmukaisena paikallisen läsnäolon lisäämiseksi. Empiirinen data kattaa kahdeksan asiantuntijahaastattelua, jotka yhdessä muun lähdeaineiston kanssa rakentavat perustan empiirisille tuloksille. Tutkimuksen tulokset tarjoavat yritykselle perustellun ratkaisuehdotuksen siitä, kuinka Pietarin markkinoille tulisi etabloitua.

Enteral fluid therapy through nasogastric tube in rumen cannulated goats

This paper reports the effects of fluid therapy in goats through nasogastric route with an electrolyte solution composed by concentrations of sodium, potassium and chloride similar to goat plasma (140mmol/L of Na+, 4.5mmol/L of K+, 110mmol/L of Cl-). Four Alpine Chamoisee goats, two of them with evident leakage of the rumen cannulas, were used in a crossover experimental design of two periods and two groups. In one group the two goats were submitted to a treatment protocol to induce dehydration before the fluid therapy, whereas the other group was not. Fluid therapy consisted supplying 10mL/kg/h of the electrolyte solution during 8 hours. No signs of discomfort or stress were observed. The dehydration model employed caused a mild dehydration indicated by decrease in feces humidity, body weight and abdominal circumference, and increase in plasma total solids concentration. During fluid therapy globular volume and plasma total solids decreased, whereas % body weight and abdominal circumference increased. No signs of hyperhydration were observed and serum electrolytes (Na+, Cl-, K+) presented no significant alterations in both groups. Fluid therapy proposed in this study was efficient to treat dehydration, even for rumen cannulated animals with evident leakage, and can be administrated safely with no electrolyte imbalance.