Functionalized Silicon Polymers: Novel Materials for Catalysis

Dept.of Applied Chemistry,Cochin University of Science and Technolgy

Ionomer Compatibilized Low Density Polyethylene - Tapioca Starch Blends Biodegradability and Photodegradability

Biodegradation is the chemical degradation of materials brought about by the action of naturally occurring microorganisms. Biodegradation is a relatively rapid process under suitable conditions of moisture, temperature and oxygen availability. The logic behind blending biopolymers such as starch with inert polymers like polyethylene is that if the biopolymer component is present in sufficient amount, and if it is removed by microorganisms in the waste disposal environment, then the base inert plastic should slowly degrade and disappear. The present work focuses on the preparation of biodegradable and photodegradable blends based on low density polyethylene incorporating small quantities of ionomers as compatibilizers. The thesis consists of eight chapters. The first chapter presents an introduction to the present research work and literature survey. The details of the materials used and the experimental procedures undertaken for the study are described in the second chapter. Preparation and characterization of low density polyethylene (LDPE)-biopolymer (starch/dextrin) blends are described in the third chapter. The result of investigations on the effect of polyethylene-co-methacrylic acid ionomers on the compatibility of LDPE and starch are reported in chapter 4. Chapter 5 has been divided into two parts. The first part deals with the effect of metal oxides on the photodegradation of LDPE. The second part describes the function of metal stearates on the photodegradation of LDPE. The results of the investigations on the role of various metal oxides as pro-oxidants on the degradation of ionomer compatibilized LDPE-starch blends are reported in chapter 6. Chapter 7 deals with the results of investigations on the role of various metal stearates as pro-oxidants on the degradation of ionomer compatibilized LDPE-starch blends. The conclusion of the investigations is presented in the last chapter of the thesis.

‘‘catalysis by nano sulfated titania modified by transition metals"

in the present study, we have prepared and evaluated the physical and chemical properties and catalytic activities of transition metal loaded sulfated titania via the sol-gel route. Sol-gel method is widely used for preparing porous materials having controlled properties and leads to the formation of oxide particles in nano range, which are spherical or interconnected to each other. Characterization using various physico-chemical techniques and a detailed study of acidic properties are also carried out. Some reactions of industrial importance such as Friedel-Crafts reaction, fen-butylation of phenol,Beckmann rearrangement of cyclohexanone oxime, nitration of phenol and photochemical degradation of methylene blue have been selected for catalytic activity study in the present venture. The work is organized into eight chapters

Synthesis And Characterization Ofpolystyrene Supportedcatalytically Active Poly(Amidoamine) Dendrimer-Palladium Nanoparticle Conjugates

Poly(amidoamine) dendrimers were synthesized on cross-linked aminomethyl polystyrene. Palladium complexes of supported dendrimers prepared by ligand exchange method were reduced to dendrimernanoparticle conjugates supported on polystyrene resin. The supported nanoparticles were used as heterogeneous catalysts for the Suzuki coupling between aryl boronic acids and aryl halides. Various factors affecting the catalysts performance were studied. Higher generation dendrimers gave well-defined nanoparticles without agglomeration and these particles showed good catalytic performance

Preparació de nous catalitzadors basats en complexos de Ru i Pd, i el seu ancorament a polímers conductors per a la fabricació de materials multifuncionals

Aquesta tesi doctoral es basa en l'estudi de l'aplicació en catàlisi de dos tipus de complexos organometallics basats en dos metalls de tansició diferents. Concretament s'estudien complexos macrocíclics triolefínics de pal·ladi(0) com a catalitzadors per a les reaccions de Suzuki i Heck, i oxocomplexos carbènics de ruteni(II) com a espècies catalítiques en oxidacions de compostos orgànics. En el cas dels complexos de ruteni s'ha vist que en augmentar el nombre de lligands carbènics en l'esfera de coordinació del metall s'aconseguiex afavorir els processos bielectrònics, obtenint-se catalitzadors més actius i més selectius. En un segon pas, els dos tipus de catalitzadors homogenis s'han immobilitzat sobre la superfície d'un elèctrode mitjançant l'estratègia d'electropolimerització del grup pirrol. Els elèctodes modificats resultants s'han aplicat com a catalitzadors heterogenis. En ambdós casos els catalitzadors heterogenis han mostrat una activitat equiparable o superior a la del sistema homogeni corresponent. Finalment, s'ha assajat una reacció de catàlisi tàndem en què els dos catalitzadors (immobilitzats sobre el mateix elèctrode) actuen en cooperació. S'ha aconseguit realitzar dues transformacions consecutives d'un substat orgànic.

Desarrollo de catalizadores en sistemas de reacción avanzados para la producción de hidrógeno a partir de biogás

[ES]En el presente documento se expone el estudio experimental que consiste en la comparación de diferentes catalizadores en sistemas de reacción avanzados, microrreactores, para la producción de hidrógeno a partir de biogás. El hidrógeno es un vector energético que puede emplearse como combustible, y por tanto, un candidato perfecto para sustituir aquellos combustibles provenientes de fuentes fósiles. Este Proyecto de Fin de Grado se ha basado en desarrollar el proceso conocido como tri-reformado de biogás. Esta técnica, al contrario que las técnicas convencionales de producción, presenta numerosas ventajas ya que la materia prima empleada, el biogás, es una fuente de origen renovable. Para llevar a cabo este estudio se han preparado distintos catalizadores, basados todos ellos en platino. La elección de este metal noble es debido a su alto grado de reactividad, especialmente en sistemas de reacción micro-estructurados. Con el objetivo de reducir los costes asociados al propio catalizador, se añadieron, junto con el platino, otros metales más baratos a fin de analizar su idoneidad en el proceso del tri-reformado. Por tanto, partiendo de un catalizador de referencia que contiene un 5% de platino, se prepararon otros catalizadores mantenido constante, en un 5%, la composición de metal total. Estos catalizadores se han denominado de la siguiente manera: 2.5(Pt-Me), siendo Me cada especie metálica diferente. Tras preparar los catalizadores, se llevaron a cabo diferentes experimentos con un reactor convencional de lecho fijo. El objetivo fue establecer unas condiciones de operación tal que asegurasen una adecuada comparación entre catalizadores. De este modo, se realizaron ensayos de actividad catalítica a diferentes temperaturas y velocidades espaciales para someter a los catalizadores a condiciones de operación extremas, bajo las cuales, las diferencias entre catalizadores fueran más notorias. Una vez detalladas las condiciones de operación adecuadas para la comparación de catalizadores, se llevaron a cabo los correspondientes ensayos con los catalizadores impregnados en los sistemas de reacción avanzados, denominados micorreactores. Estos ensayos se basaron en operar a una velocidad espacial constante para estudiar la influencia de la temperatura. Además, se llevaron a cabo ensayos de estabilidad de hasta 110 horas en las condiciones de operación más desfavorables. Por último se compararon las conversiones de CH4 y CO2 y el rendimiento de H2 de todas las formulaciones catalíticas preparadas, y se concluyó que el mejor candidato para el proceso del tri-reformado es el catalizador 2.5(Pt-Pd).

Electronic structure of point defects in controlled self-doping of the TiO2 (110) surface: Combined photoemission spectroscopy and density functional theory study

Point defects in metal oxides such as TiO2 are key to their applications in numerous technologies. The investigation of thermally induced nonstoichiometry in TiO2 is complicated by the difficulties in preparing and determining a desired degree of nonstoichiometry. We study controlled self-doping of TiO2 by adsorption of 1/8 and 1/16 monolayer Ti at the (110) surface using a combination of experimental and computational approaches to unravel the details of the adsorption process and the oxidation state of Ti. Upon adsorption of Ti, x-ray and ultraviolet photoemission spectroscopy (XPS and UPS) show formation of reduced Ti. Comparison of pure density functional theory (DFT) with experiment shows that pure DFT provides an inconsistent description of the electronic structure. To surmount this difficulty, we apply DFT corrected for on-site Coulomb interaction (DFT+U) to describe reduced Ti ions. The optimal value of U is 3 eV, determined from comparison of the computed Ti 3d electronic density of states with the UPS data. DFT+U and UPS show the appearance of a Ti 3d adsorbate-induced state at 1.3 eV above the valence band and 1.0 eV below the conduction band. The computations show that the adsorbed Ti atom is oxidized to Ti2+ and a fivefold coordinated surface Ti atom is reduced to Ti3+, while the remaining electron is distributed among other surface Ti atoms. The UPS data are best fitted with reduced Ti2+ and Ti3+ ions. These results demonstrate that the complexity of doped metal oxides is best understood with a combination of experiment and appropriate computations.

Magnetically separable, carbon-supported nanocatalysts for the manufacture of fine chemicals

The best of both worlds: The synthesis of carbon-encapsulated iron-based magnetic nanoparticles is described. With such small catalysts that have macroscopic magnetic properties, the advantages of homogeneous or colloidal and heterogeneous catalysts can be combined.

Dielectric properties and physical features of phosphate glasses containing iron oxide

Microwave techniques were applied to the study of dielectric properties of phosphate glasses on the basis of contributions from permanent and induced dipolar polarization of local structural units interacting with the electrical component of the electromagnetic radiation. The dielectric constant of the selected glass system (100-x)(50P(2)O(5)center dot 25Li(2)O center dot 25Na(2)O)center dot xFe(2)O(3), where 0 <= x <= 21 is in mol%, was measured using a microwave setup assembled to measure the phase shift of the standing wave pattern produced by the insertion of the sample. It is shown that the Fe2+ ions contribute effectively to the dielectric constant, as expected from the interactions of the dipoles of the local charge compensation pairs with the microwave radiation. However, there is the possibility of occurrence of some ions Fe3+, in general, at low iron content, which reinforces the glass structure and, therefore, decreases the dielectric constant. There is a gradual conversion from Fe3+ to Fe2+ as the iron ions increases. This is possibly the reason of the anomaly in the dielectric constant values observed in the results. These assumptions can be checked by results of electronic paramagnetic resonance (EPR) and optical absorption (OA). The dielectric constant of the glasses studied in this work was found to increase with the temperature in the range of 25-330 degrees C. (C) 2007 Elsevier B.V. All rights reserved.

Orbital-polarization terms: From a phenomenological to a first-principles description of orbital magnetism in density-functional theory

Phenomenological orbital-polarizition (OP) terms have been repeatedly introduced in the single-particle equations of spin-density-functional theory, in order to improve the description of orbital magnetic moments in systems containing transition metal ions. Here we show that these ad hoc corrections can be interpreted as approximations to the exchange-correlation vector potential A(xc) of current-density functional theory (CDFT). This connection provides additional information on both approaches: phenomenological OP terms are connected to first-principles theory, leading to a rationale for their empirical success and a reassessment of their limitations and the approximations made in their derivation. Conversely, the connection of OP terms with CDFT leads to a set of simple approximations to the CDFT potential A(xc), with a number of desirable features that are absent from electron-gas-based functionals. (C) 2008 Wiley Periodicals, Inc.

NMR study of slow motions of HDA hydrocarbons chains inside lamellar structures

Measurements of H-1 and C-13 Nuclear Magnetic Resonance (NMR) for the nano-composite materials formed by the intercalation of hexadecylamine (HDA) in metal oxides (TiO2, V2O5 and MoO3), are reported. The H-1 NMR spin-lattice relaxation in the rotating frame was described by using the spectral density due to Davidson and Cole, which incorporates a distribution of correlation times characterized by a width parameter epsilon. The fitting of the data was obtained for epsilon = 0.74, indicating that the correlation times are distributed over a narrow range in this system. High-resolution C-13 NMR techniques were used to resolve the NMR lines of middle-chain methylene groups in the spectra and variable contact time cross-polarization {H-1-}C-13 experiments were employed to analyze the reorientation dynamics of the CH3 and CH2 groups in the HDA chains.

Ethanol chemiresistor with enhanced discriminative ability from acetone based on Sr-doped SnO2 nanofibers

We demonstrated a new metal oxides based chemiresistor (MOC), which exhibits fast response/recovery behavior, large sensitivity, and good selectivity to ethanol, enabled by Sr-doped SnO2 nanofibers via simple electrospinning and followed by calcination. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectra (XPS) were carefully used to characterize their morphology, structure, and composition. The ethanol sensing performances based on Sr-doped SnO2 nanofibers were investigated. Comparing with the pristine SnO2 nanofibers, enhanced ethanol sensing performances (more rapid response/recovery behavior and larger response values) have been achieved owing to the basic SnO2 surface caused by Sr-doping, whereas the acetone sensing performances have been weakened. Thus, good discriminative ability to ethanol from acetone has been realized. Additionally, Sr-doped SnO2 nanofibers also exhibit good selectivity.

Highly sensitive SnO2 nanofiber chemiresistors with a low optimal operating temperature: synergistic effect of Cu2+/Au co-doping

Metal oxide chemiresistors (MOCs) with a low optimal operating temperature, high sensitivity and fast response/recovery are highly promising for various applications, but remain challenging to realize. Herein, we demonstrate that SnO2 nanofibers after being co-doped with Cu2+ and Au show considerably enhanced sensing performances at an unexpectedly decreased operating temperature. A synergistic effect occurs when the two dopants are introduced together. Co-doping may form a novel strategy to the development of ultrasensitive MOCs working at a low optimal temperature. This journal is © the Partner Organisations 2014.

Pd embedded in porous carbon (Pd@CMK-3) as an active catalyst for Suzuki reactions: accelerating mass transfer to enhance the reaction rate

Heterogeneous catalysts are promising candidates for use in organic reactions due to their advantages in separation, recovery, and environment compatibility. In this work, an active porous catalyst denoted as Pd embedded in porous carbon (Pd@CMK-3) has been prepared by a strategy involving immersion, ammoniahydrolysis, and heating procedures. Detailed characterization of the catalyst revealed that Pd(0) and Pd(II) species co-exist and were embedded in the matrix of the porous carbon (CMK-3). The as-prepared catalyst has shown high activity toward Suzuki reactions. Importantly, if the reaction mixture was homogenized by two minutes of ultrasonication rather than magnetic stirring before heating, the resistance to mass transfer in the pore channels was significantly reduced. As a result, the reactions proceeded more rapidly and a four-fold increase in the turnover frequency (TOF) could be obtained. When the ultrasonication was employed throughout the entire reaction process, the conversion could also exceed 90% even without the protection of inert gas, and although the reaction temperature was lowered to 30 °C. This work provides a method for fabricating highly active porous carbon encapsulated Pd catalysts for Suzuki reactions and proves that the problem of mass transfer in porous catalysts can be conveniently resolved by ultrasonication without any chemical modification being necessary.[Figure not available: see fulltext.] © 2014 Tsinghua University Press and Springer-Verlag Berlin Heidelberg.

A self-supported, flexible, binder-free pseudo-supercapacitor electrode material with high capacitance and cycling stability from hollow, capsular polypyrrole fibers

Flexible energy devices with high performance and long-term stability are highly promising for applications in portable electronics, but remain challenging to develop. As an electrode material for pseudo-supercapacitors, conducting polymers typically show higher energy storage ability over carbon materials and larger conductivity than transition-metal oxides. However, conducting polymer-based supercapacitors often have poor cycling stability, attributable to the structural rupture caused by the large volume contrast between doping and de-doping states, which has been the main obstacle to their practical applications. Herein, we report a simple method to prepare a flexible, binder-free, self-supported polypyrrole (PPy) supercapacitor electrode with high cycling stability through using novel, hollow PPy nanofibers with porous capsular walls as a film-forming material. The unique fiber structure and capsular walls provide the PPy film with enough free-space to adapt to volume variation during doping/de-doping, leading to super-high cycling stability (capacitance retention > 90% after 11000 charge-discharge cycles at a high current density of 10 A g^-1) and high rate capability (capacitance retention ∼ 82.1% at a current density in the range of 0.25-10 A g^-1).