Mechanical properties of chemically modified portuguese pinewood

To turn wood into a construction material with enhanced properties, many methods of chemical modification have been developed in the last few decades. In this work, mechanical properties of pine wood were chemically modified, compared and evaluated. Maritime pine wood (Pinus pinaster) was modified with four chemical processes: 1,3-dimethylol-4,5- dihydroxyethyleneurea, N-methylol melamine formaldehyde, tetra-alkoxysilane and wax. The following mechanical properties were assessed experimentally: Modulus of elasticity measured statically, stiffness stabilization efficiency in different climates (30 and 87% of relative humidity), modulus of rupture, work maximum load, impact bending strength, compression, tensile and shear strength at indoor conditions (65% of relative humidity). In both types of active principle of modification, cell wall or lumen fill, no significant changes on the bending stiffness (modulus of elasticity) were found. In the remaining properties analysed significant changes in the modified wood-material took place compared to unmodified wood control: - Cell wall modification was the most effective method to achieve high stiffness stabilization efficiency (up to 60%) and also increased compression strength (up to 230%). However, modulus of rupture, tensile, shear and the impact bending strength were reduced by both resins, but in a varying extent, where the N-methylol melamine formaldehyde endured less reduction than 1,3-dimethylol-4,5-dihydroxyethyleneurea resin. In the latter, reduction up to 60% can take place. - In the lumen fill modification: tetra-alkoxysilane has no effect in the mechanical properties. Although, a slight increase in shear strength parallel to the grain was found. Wax specimens have shown a slight increase in bending strength, compression, tensile and shear strength as well as in the absorption energy capacity.

A Multiple Criteria Utility-based Approa h for the Unit Commitment with Wind Power and Pumped Storage Hydro

The integration of wind power in eletricity generation brings new challenges to unit commitment due to the random nature of wind speed. For this particular optimisation problem, wind uncertainty has been handled in practice by means of conservative stochastic scenario-based optimisation models, or through additional operating reserve settings. However, generation companies may have different attitudes towards operating costs, load curtailment, or waste of wind energy, when considering the risk caused by wind power variability. Therefore, alternative and possibly more adequate approaches should be explored. This work is divided in two main parts. Firstly we survey the main formulations presented in the literature for the integration of wind power in the unit commitment problem (UCP) and present an alternative model for the wind-thermal unit commitment. We make use of the utility theory concepts to develop a multi-criteria stochastic model. The objectives considered are the minimisation of costs, load curtailment and waste of wind energy. Those are represented by individual utility functions and aggregated in a single additive utility function. This last function is adequately linearised leading to a mixed-integer linear program (MILP) model that can be tackled by general-purpose solvers in order to find the most preferred solution. In the second part we discuss the integration of pumped-storage hydro (PSH) units in the UCP with large wind penetration. Those units can provide extra flexibility by using wind energy to pump and store water in the form of potential energy that can be generated after during peak load periods. PSH units are added to the first model, yielding a MILP model with wind-hydro-thermal coordination. Results showed that the proposed methodology is able to reflect the risk profiles of decision makers for both models. By including PSH units, the results are significantly improved.

Lack of methicillin-resistant Staphylococcus aureus nasal carriage among patients at a primary-healthcare unit in Porto Alegre, Brazil

INTRODUCTION: Community-associated methicillin-resistant Staphylococcus aureus (MRSA) has emerged as a pathogen in individuals without traditional risk factors. MATERIAL AND METHODS: MRSA nasal carriage was assessed in individuals consulting at a Primary Health Unit in Brazil. RESULTS: A total of 336 individuals were included: 136 were tested only for MRSA and 200 for any S. aureus. No MRSA was found among the 336 individuals and 23 (11.5%) of 200 were colonized by S. aureus. DISCUSSION: Low prevalence rates have been found in non-hospitalized individuals, but MRSA surveillance should be encouraged to monitor clinical and molecular epidemiology of CA- MRSA.

HIV-1-mother-to-child transmission and associated characteristics in a public maternity unit in Presidente Prudente, Brazil

In children, vertical transmission is the main form of HIV infection. Our aim was to determine the prevalence of HIV-1 vertical transmission in mother-infant pairs in a public maternity ward in Presidente Prudente, SP. Additionally; we sought to identify characteristics associated with this form of transmission. The files of 86 HIV-1-infected mothers and their newborns referred to a Public Hospital from March 2002 to March 2007 were analyzed. The HIV-1-RNA viral load of the newborns was determined by bDNA. The HIV-1 vertical-transmission rate was 4.6%. Children that were born in the pre-term period and breastfed were at a higher risk of HIV-1 infection (p = 0.005 and p = 0.017 respectively) than children born at term and not breastfed. Prophylactic therapy with zidovudine after birth for newborns was associated with a lower risk of infection (p = 0.003). The number of newborns weighing < 2,500 g was significantly higher for infected children (p = 0.008) than for non-infected newborns. About 22.9% of mothers did not know the HIV-1 status of their newborns eight months after delivery. The study suggests that it is necessary to increase the identification of HIV-1 infection in pregnant women and their newborns as well as to offer and explain the benefits of ARV prophylaxis.

Correlation between the mechanical cycling behavior and microstructure in laser welded joints using NiTi memory shape alloys

Dissertação para obtenção do Grau de Mestre em Engenharia de Materiais

Toxocariasis in children attending a Public Health Service Pneumology Unit in Paraná State, Brazil

The enzyme-linked immunosorbent assay (ELISA) is the most widely used tool to detect anti-Toxocara IgG antibodies for both serodiagnostic and seroepidemiological surveys on human toxocariasis. In the last eight years a high prevalence of toxocariasis (32.2-56.0%) has been reported in children attending public health units from municipalities in the state of Paraná, Brazil. Therefore, the aim of this work was to compare the frequency found among the general child population with that of children attending a public pneumology service in Maringá, Paraná, Brazil and describe the laboratorial, clinical and epidemiological findings. The research was conducted at the Consórcio Público Intermunicipal de Saúde do Setentrião Paranaense (CISAMUSEP) from July 2009 to July 2010 among children aged between one and 15 years. From a total of 167 children studied, only 4.2% (7/167) tested positive for anti-Toxocara spp. IgG antibodies and presented mild eosinophilia (2/7), increased serum IgE levels (6/7) and a positive allergy test for mites (5/7). The presence of pets (dogs or cats) at home did not correlate with the seroprevalence. In conclusion, cases of toxocariasis involving the respiratory tract are rare in children attending a public health pneumology unit in the northwestern region of Paraná State, despite the high prevalence of this type of toxocariasis among the infantile population attending Basic Health Units in the same geographical area.

Modeling in-Hospital Patient Survival During the First 28 Days After Intensive Care Unit Admission: a Prognostic Model for Clinical Trials in General Critically Ill Patients

OBJECTIVE: The objective of the study was to develop a model for estimating patient 28-day in-hospital mortality using 2 different statistical approaches. DESIGN: The study was designed to develop an outcome prediction model for 28-day in-hospital mortality using (a) logistic regression with random effects and (b) a multilevel Cox proportional hazards model. SETTING: The study involved 305 intensive care units (ICUs) from the basic Simplified Acute Physiology Score (SAPS) 3 cohort. PATIENTS AND PARTICIPANTS: Patients (n = 17138) were from the SAPS 3 database with follow-up data pertaining to the first 28 days in hospital after ICU admission. INTERVENTIONS: None. MEASUREMENTS AND RESULTS: The database was divided randomly into 5 roughly equal-sized parts (at the ICU level). It was thus possible to run the model-building procedure 5 times, each time taking four fifths of the sample as a development set and the remaining fifth as the validation set. At 28 days after ICU admission, 19.98% of the patients were still in the hospital. Because of the different sampling space and outcome variables, both models presented a better fit in this sample than did the SAPS 3 admission score calibrated to vital status at hospital discharge, both on the general population and in major subgroups. CONCLUSIONS: Both statistical methods can be used to model the 28-day in-hospital mortality better than the SAPS 3 admission model. However, because the logistic regression approach is specifically designed to forecast 28-day mortality, and given the high uncertainty associated with the assumption of the proportionality of risks in the Cox model, the logistic regression approach proved to be superior.

Projeto de uma unidade de produção de biodiesel num reator ultrassónico pela via supercrítica

A concretização deste estágio na INCBIO teve como principal objetivo o projeto e dimensionamento de uma unidade de produção de biodiesel por transesterificação nãocatalítica num reator ultrassónico com condições supercríticas de pressão e temperatura. Com vista à concretização do trabalho, iniciou-se a realização do estudo do estado da arte relativo à produção de biodiesel, com particular enfoque na produção de biodiesel por via catalítica e por via supercrítica e na produção de biodiesel com uso de tecnologia ultrassónica. Conclui-se que nenhum estudo contempla a combinação simultânea da produção de biodiesel por via supercrítica através da tecnologia ultrassónica. Este estudo do estado da arte permitiu ainda definir as condições de temperatura, pressão e rácio mássico (250 °C, 95 bar e 1:1 respetivamente) a considerar no projeto da unidade de produção de biodiesel deste trabalho. Com base no estudo do estado da arte efetuado e com base nas características da matéria procedeu-se à definição do processo de produção de biodiesel. Para a definição do processo começou-se por elaborar o diagrama de blocos do processo (BFD) e o diagrama de fluxo do processo (PFD). Com base nos diagramas e na composição da matéria-prima, procedeu-se à quantificação dos reagentes (metanol) com base na estequiometria das reações envolvidas e ao cálculo do balanço de massa. O balanço de massa foi calculado com base na estequiometria das reações envolvidas e foi também calculado através do software de simulação ASPEN PLUS. Após o cálculo do balanço de massa elaborou-se o diagrama de tubulação e instrumentação (P&ID), que contém todos os equipamentos, válvulas, instrumentação e tubagens existentes na unidade. Após a definição do processo e cálculo do balanço de massa procedeu-se ao dimensionamento mecânico e cálculo hidráulico dos tanques, tubagem, bombas, permutador de calor, reator ultrassónico, válvulas de controlo e instrumentação de acordo com as normas ASME. Nesta fase do trabalho foram consultados diversos fornecedores possíveis para a compra de todo o material necessário. O dimensionamento mecânico e cálculo hidráulico efetuados permitiram, entre outras informações relevantes, obter as dimensões necessárias à construção do layout e à elaboração do desenho 3D. Com os resultados obtidos e desenhos elaborados, é possível avançar com a construção da unidade, pelo que pode-se inferir que o objetivo de projetar uma unidade de produção de biodiesel num reator ultrassónico com condições supercríticas foi alcançado. Por fim, efetuou-se uma análise económica detalhada que possibilita a comparação de uma unidade de produção de biodiesel por via catalítica (unidade de produção da INCBIO) com a unidade de produção de biodiesel num reator ultrassónico com condições supercríticas (unidade projetada neste trabalho). Por questões de confidencialidade, não foram revelados maior parte dos resultados da análise económica efetuada. No entanto, conclui-se que os custos de construção da unidade de produção de biodiesel num reator ultrassónico com condições supercríticas são mais baixos cerca de 35 a 40%, quando comparados com os custos de construção da unidade de produção de biodiesel por via catalítica, evidenciando assim que a combinação em simultâneo das condições supercríticas com a tecnologia ultrassónica possibilita a diminuição dos custos de produção.

Análise e implementação de melhorias no serviço Pós-Venda na área automóvel

No âmbito da unidade curricular de Dissertação/Projeto/Estágio, pertencente ao segundo ano do Mestrado em Engenharia Mecânica – Ramo de Gestão Industrial do Instituto Superior de Engenharia do Porto, o presente trabalho foi desenvolvido no Grupo JAP, Grupo do setor automóvel, desenvolvido especificamente no serviço pós-venda. Numa realidade bastante diferente de outros tempos onde havia grandes margens com a venda de produtos, hoje a realidade é bem diferente. Num contexto de competição global onde as margens são mais reduzidas, o serviço pós-venda, onde o cliente é acompanhado desde da compra até o fim de vida do produto, constitui uma fonte de receitas relevante bem como um diferenciador chave dentre as empresas de revenda automóvel. Por estas razões, são cada vez mais as empresas que seguem a filosofia Lean, orientando toda a sua estrutura produtiva no sentido de atingir zero desperdícios, sem interferir com a qualidade do produto final. A realização deste projeto teve como objetivo o desenvolvimento e adequação de ferramentas de melhoria e apoio ao serviço pós-venda no Grupo. Com a elaboração deste trabalho, pretende-se fazer uma análise a todo o processo do serviço pós-venda, identificando os problemas que ocorrem ao longo do processo e desenvolver um plano de ações de melhoria, utilizando para isso as ferramentas da metodologia Lean. Em primeiro lugar, fez-se uma análise do processo do serviço pós-venda e do serviço do armazém de peças, onde foram identificados alguns pontos de melhoria e recolhidos as primeiras informações para uma análise mais aprofundada de cada problema. Posteriormente, estabeleceu-se um plano de ações para eliminar ou minimizar os desperdícios encontrados no processo, aumentar a produtividade e a qualidade do serviço prestado ao cliente, e procedeu-se à implementação das melhorias. Após a implementação das melhorias, fez-se uma avaliação das mesmas e constatou-se um aumento de produtividade, uma redução de desperdícios e um aumento dos índices de qualidade. Em suma uma melhoria no serviço prestado ao cliente.

Projeto mecânico de equipamento para fabrico automatizado de vestuário

O fabrico de vestuário é uma atividade que se desenvolve em Portugal há várias décadas. Existem marcas de vestuário com reconhecimento a nível mundial que são de origem portuguesa. Para se conseguir qualidade é necessário inovar e automatizar determinados processos, de forma a aumentar produtividades e reduzir erros devido à mão de obra de tarefas intensivas. Na empresa Portuguesa Henrique Camões, com uma vasta experiência ligada a equipamentos de fabrico têxtil, nasceu a ideia de projetar um protótipo de um equipamento automatizado para o fabrico de colarinhos e punhos, com a finalidade de verificar a sua viabilidade a nível funcional. Este trabalho teve assim por base a necessidade de efetuar um projeto sobre um equipamento capaz de costurar e cortar colarinhos e punhos, a serem aplicados em peças de vestuário. Inicialmente foi efetuado um estudo prévio de levantamento de equipamentos já existentes para fins semelhantes. Foi então necessário idealizar um equipamento capaz de responder às expectativas e exigências por parte do cliente. Após os esboços iniciais, onde foram definidos os tipos de mecanismos e formas de funcionamento dos diferentes sistemas em função dos movimentos e ações pretendidas e a estrutura do equipamento, estes sistemas foram otimizados por forma a se obter como resultado final um equipamento funcional. Foi também projetado o esquema pneumático e Grafcet de funcionamento do equipamento. Como auxiliares do projeto, apresentam-se a lista de componentes e de processos de fabrico, bem como os desenhos de pormenor de todos os componentes integrantes da estrutura. O resultado final é um conjunto de ideias e soluções possíveis de aplicar num equipamento deste tipo. De facto, a solução proposta é uma possibilidade viável para um equipamento automatizado para costura e corte de colarinhos e punhos.

Aircraft Engines Maintenance Costs and Reliability: An Appraisal of the Decision Process to Remove an Engine for a Shop Visit Aiming at Minimum Maintenance Unit Cost

Dissertação apresentada como requisito parcial para obtenção do grau de Mestre em Estatística e Gestão de Informação.

Multiple Mechanical Complications in ST-Segment Elevation Myocardial Infarction with Angiographically Normal Coronary Arteries

This case report discusses an unusual presentation of ST-segment elevation myocardial infarction (STEMI) with normal coronary arteries and severe mechanical complications successfully treated with surgery. An 82-year-old man presented STEMI with angiographically normal coronary arteries and no major echocardiographic alterations at discharge. At the first month follow-up, he complained of fatigue and dyspnea, and contrast echocardiography complemented by cardiac magnetic resonance imaging revealed a large left ventricular apical aneurysm with a thrombus communicating by two jets of a turbulent flow to an aneurysmatic formation of the right ventricular apex. The patient underwent a Dor procedure, which was successful. Ventricular septal defects and ventricular aneurysms are rare but devastating complications of STEMI, with almost all patients presenting multivessel coronary artery disease. Interestingly in this case, the angiographic pattern was normal.

How effective are brief interventions in smoking cessation: project of a cohort study in a family health care unit

ABSTRACT: Tobacco use remains the most significant modifiable cause of disability, death and illness1. In Portugal, 19,6% of the population aged ten years or more smoke3. A Cochrane review of 20087 concluded that a brief advice intervention (compared to usual care) can increase the likelihood of a smoker to quit and remain nonsmoker 12 months later by a further 1 to 3 %. Several studies have shown that Primary Care Physicians can play a key role in these interventions8,9,10. However we did not find studies about the effectiveness of brief interventions in routine consultations of Family Doctors in Portugal. For this reason we designed a Cohort Study to make an exploratory study about the effectiveness of brief interventions of less than three minutes in comparison with usual care in routine consultations. The study will be implemented in a Family Healthcare Unit in Beja, during six months. Family Doctors of the intervention group should be submitted for an educational and training program before the study begin. Quit smoking sustained rates will be estimated one year after the first intervention in each smoker. If, as we expect, quit smoking rates will be higher in the intervention group than in the control group, this may change Portuguese Family Doctors attitudes and increase the provision of brief interventions in routine consultations in Primary Healthcare Centers.

Iron Overload in a Murine Model of Hereditary Hemochromatosis Is Associated with Accelerated Progression of Osteoarthritis Under Mechanical Stress

OBJECTIVE: Hereditary hemochromatosis (HH) is a disease caused by mutations in the Hfe gene characterised by systemic iron overload and associated with an increased prevalence of osteoarthritis (OA) but the role of iron overload in the development of OA is still undefined. To further understand the molecular mechanisms involved we have used a murine model of HH and studied the progression of experimental OA under mechanical stress. DESIGN: OA was surgically induced in the knee joints of 10-week-old C57BL6 (wild-type) mice and Hfe-KO mice. OA progression was assessed using histology, micro CT, gene expression and immunohistochemistry at 8 weeks after surgery. RESULTS: Hfe-KO mice showed a systemic iron overload and an increased iron accumulation in the knee synovial membrane following surgery. The histological OA score was significantly higher in the Hfe-KO mice at 8 weeks after surgery. Micro CT study of the proximal tibia revealed increased subchondral bone volume and increased trabecular thickness. Gene expression and immunohistochemical analysis showed a significant increase in the expression of matrix metallopeptidase 3 (MMP-3) in the joints of Hfe-KO mice compared with control mice at 8 weeks after surgery. CONCLUSIONS: HH was associated with an accelerated development of OA in mice. Our findings suggest that synovial iron overload has a definite role in the progression of HH-related OA

Acute Kidney Injury after Pediatric Cardiac Surgery: Risk Factors and Outcomes. Proposal for a Predictive Model

Objectives: To characterize the epidemiology and risk factors for acute kidney injury (AKI) after pediatric cardiac surgery in our center, to determine its association with poor short-term outcomes, and to develop a logistic regression model that will predict the risk of AKI for the study population. Methods: This single-center, retrospective study included consecutive pediatric patients with congenital heart disease who underwent cardiac surgery between January 2010 and December 2012. Exclusion criteria were a history of renal disease, dialysis or renal transplantation. Results: Of the 325 patients included, median age three years (1 day---18 years), AKI occurred in 40 (12.3%) on the first postoperative day. Overall mortality was 13 (4%), nine of whom were in the AKI group. AKI was significantly associated with length of intensive care unit stay, length of mechanical ventilation and in-hospital death (p<0.01). Patients’ age and postoperative serum creatinine, blood urea nitrogen and lactate levels were included in the logistic regression model as predictor variables. The model accurately predicted AKI in this population, with a maximum combined sensitivity of 82.1% and specificity of 75.4%. Conclusions: AKI is common and is associated with poor short-term outcomes in this setting. Younger age and higher postoperative serum creatinine, blood urea nitrogen and lactate levels were powerful predictors of renal injury in this population. The proposed model could be a useful tool for risk stratification of these patients.