Influência da técnica de fabricação e dos materiais sobre o ajuste da interface pilar/implante em infraestruturas implantossuportadas

The aim of this study was to compare the misfit vertical, horizontal and passivity of zirconia and cobalt-chromium frameworks fabricated for CAD / CAM technology and conventional method of casting. Sixteen frameworks in one-piece, were obtained from a metallic matrix containing three Brånemark compatible implants with regular platform (Titamax Cortical Ti, Neodent). Eight frameworks were fabricated by CAD / CAM system (NeoShape, Neodent): four in zirconia (ZirCAD) and four cobalt-chromium (CoCrcad). Eight other frameworks were obtained by conventional casting method: four cobalt-chromium with UCLA abutment premachined Co-Cr (CoCrUCci) and four cobalt-chromium with UCLA abutment castable (CoCrUCc). The fit vertical, horizontal and passivity by one-screw test were measured using scanning electron microscopy with magnification of 250x. Initially evaluated the passivity by one-screw test and subsequently to assess the vertical and horizontal misfit, tightened all the screws with a torque of 20 Ncm. Mean, standard deviation, minimum and maximum values were calculated for each group. Measurements of horizontal misfit were transformed into cumulative frequency for categorization of the variable and the group later comparison groups. To evaluate the existence of quantitative differences between the groups tested for vertical misfit and passivity, we used the Kruskal-Wallis test. The Mann-Whitney test was used to compare group to group statistical differences (p <0.05). Were observed the respective mean and standard deviation for vertical misfit and passivity in micrometers: ZirCAD (5.9 ± 3.6, 107.2 ± 36), CoCrcad (1.2 ± 2.2, 107.5 ± 26 ), CoCrUCci (11.8 ± 9.8, 124.7 ± 74), CoCrUCc (12.9 ± 11.0, 108.8 ± 85). There were statistical differences in measures of vertical misfit (p = 0.000). The Mann-Whitney test revealed statistical differences (p <0.05) between all groups except between CoCrUCci and CoCrUCc (p = 0.619). No statistical difference was observed for the passivity. In relation to the horizontal misfit groups ZirCAD and CoCrcad did not show best values in relation to CoCrUCci and CoCrUCc. Based on the results it can be concluded that frameworks fabricated by CAD / CAM technology had better values of vertical fit than those manufactured by the casting method, nevertheless, the passivity was not influenced by manufacturing technique and material used. The horizontal fit obtained by frameworks manufactured by CAD / CAM was not superior to those manufactured by casting. A lower variability in vertical adjustment and passivity was observed when frameworks were fabricated by CAD / CAM technology

Serviço social na educação: análise das tendencias dos perfis pedagógicos do assistente social

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Conhecimento sobre ergonomia no âmbito acadêmico: um estudo com alunos e professores de odontologia

OBJETIVO: As doenças osteomusculares são as afecções ocupacionais mais prevalentes em cirurgiões-dentistas. Nosso propósito: 1) investigar os conhecimentos, aplicabilidades clínicas dos princípios ergonômicos em discentes e docentes em atividades clínicas de uma universidade pública 2) pesquisar a incidência de sintomatologias dolorosas no pescoço, ombros, parte superior e inferior das costas, cotovelos, quadris, coxas, joelhos, tornozelos e pés no universo de alunos em estágios clínicos. 3) incitar discussões de normas e diretrizes ergonômicas na universidade. MÉTODOS: Esse estudo investigou o universo de alunos matriculados em disciplinas clínicas (148) e respectivos professores (30) do curso de odontologia da Universidade Federal do Rio Grande do Norte, Natal-RN a respeito dos princípios ergonômicos utilizados na rotina clínica. Paralelamente foi pesquisada a incidência de sintomatologia dolorosa nos alunos por intermédio do questionário nórdico e a partir dos resultados foi mensurado o índice de severidade dos sintomas em alunos. The Nordic Musculoskeletal Questionnaire (NMQ) é um instrumento de diagnóstico, proposto para padronizar a mensuração de relatos de sintomas osteomusculares. A análise dos dados foi através do programa SPSS-Statistical Package for the Social Sciences, versão 17.0 realizada analítica e descritivamente, com determinação das médias (x), desvio-padrão para variáveis quantitativas, freqüências simples e relativas para as variáveis categóricas, além da estatística de associação entre grupos (teste t) e a análise de associação do quiquadrado com nível de significância 5% entre as variáveis (Person). As respostas das questões abertas foram codificadas e transformadas em freqüências, descritas posteriormente. RESULTADOS: A aplicabilidade de medidas ergonômicas nas clínicas universitárias não foi evidenciada pelo universo de discentes e docentes. Quanto ao relato de sintomas osteomusculares o sexo feminino foi o mais acometido qualquer que seja o nível acadêmico cursado. As regiões anatômicas de maior grau de severidade de relatos dos sintomas foram: pescoço, parte inferior das costas, punhos, mãos e ombros, com significância etatística p<0,001. CONCLUSÃO: Em função dos achados os autores apresentam um protocolo de intervenção clínica baseado nos determinantes ergonômicos da Associação internacional de ergonomia (EAI) como medida de prevenção da saúde ocupacional dos futuros cirurgiões-dentistas ainda em processo de formação nas clínicas odontológicas das universidades.

Rotura gástrica por barotrauma

Barogenic rupture of the stomach is a rare complication following cardiopulmonary resuscitation, administration of nasal oxygen by catheter and diving accidents. We report a case of gastric barotrauma following oroesophageal intubation. In most cases, the tears occur along the lesser curvature, what have been already attributed to Laplace's formula and, more recently, to morphological features of the stomach.

Sistema não-Intrusivo para Estimação da Direção do olhar utilizando redes neurais artificiais

The fundamental senses of the human body are: vision, hearing, touch, taste and smell. These senses are the functions that provide our relationship with the environment. The vision serves as a sensory receptor responsible for obtaining information from the outside world that will be sent to the brain. The gaze reflects its attention, intention and interest. Therefore, the estimation of gaze direction, using computer tools, provides a promising alternative to improve the capacity of human-computer interaction, mainly with respect to those people who suffer from motor deficiencies. Thus, the objective of this work is to present a non-intrusive system that basically uses a personal computer and a low cost webcam, combined with the use of digital image processing techniques, Wavelets transforms and pattern recognition, such as artificial neural network models, resulting in a complete system that performs since the image acquisition (including face detection and eye tracking) to the estimation of gaze direction. The obtained results show the feasibility of the proposed system, as well as several feature advantages.

Localização de faltas em linhas de transmissão usando morfologia matemática

This work an algorithm for fault location is proposed. It contains the following functions: fault detection, fault classification and fault location. Mathematical Morphology is used to process currents obtained in the monitored terminals. Unlike Fourier and Wavelet transforms that are usually applied to fault location, the Mathematical Morphology is a non-linear operation that uses only basic operation (sum, subtraction, maximum and minimum). Thus, Mathematical Morphology is computationally very efficient. For detection and classification functions, the Morphological Wavelet was used. On fault location module the Multiresolution Morphological Gradient was used to detect the traveling waves and their polarities. Hence, recorded the arrival in the two first traveling waves incident at the measured terminal and knowing the velocity of propagation, pinpoint the fault location can be estimated. The algorithm was applied in a 440 kV power transmission system, simulated on ATP. Several fault conditions where studied and the following parameters were evaluated: fault location, fault type, fault resistance, fault inception angle, noise level and sampling rate. The results show that the application of Mathematical Morphology in faults location is very promising

Modelo de risco com dependência entre os valores das indenizações e seus intervalos entre ocorrências

We present a dependent risk model to describe the surplus of an insurance portfolio, based on the article "A ruin model with dependence between claim sizes and claim intervals"(Albrecher and Boxma [1]). An exact expression for the Laplace transform of the survival function of the surplus is derived. The results obtained are illustrated by several numerical examples and the case when we ignore the dependence structure present in the model is investigated. For the phase type claim sizes, we study by the survival probability, considering this is a class of distributions computationally tractable and more general

Usando a história da resolução de alguns problemas para introduzir conceitos: sistemas lineares, determinantes e matrizes.

In this work we studied the method to solving linear equations system, presented in the book titled "The nine chapters on the mathematical art", which was written in the first century of this era. This work has the intent of showing how the mathematics history can be used to motivate the introduction of some topics in high school. Through observations of patterns which repeats itself in the presented method, we were able to introduce, in a very natural way, the concept of linear equations, linear equations system, solution of linear equations, determinants and matrices, besides the Laplacian development for determinants calculations of square matrices of order bigger than 3, then considering some of their general applications

Estudo geoquímico e geocronológico Rb-Sr e Sm-Nd em zonas de cisalhamento mineralizadas em ouro e suas relações com as rochas encaixantes e geocronológico Sm-Nd em mineralizações de scheelita na faixa Seridó

Great part of the gold mineralizations are associated with shearing zones through which circulate a great volume of fluids, that interact with the host rocks, originating leaching or precipitation of chemical elements, including gold. The studied mineralizations are inserted in the Seridó Belt. The tungsten mineralization in Brejuí Mine is hosted in calcsilicate rocks from Jucurutu Formation. The São Francisco auriferous mineralization has as host rocks mica-schists from Seridó Formation, while the Ponta da Serra and Fazenda Simpático mineralizations are hosted in orthogneisses of this fold belt basement. The research conducted on these mineralizations had the purpose of integrate the data of chemical elements behavior during the shearing/mineralizing event, and its influence on the isotopic systems Rb-Sr and Sm-Nd. The studies of chemical mobility in the auriferous mineralizations showed that elements that during the shearing displayed in general an immobile behavior were Al, Ti and Zr. Among the elements that were mobilized during the event, K and Rb showed mass gain in ali belts of transformed rocks, while the elements Ca, Na and Sr normally lost mass. Petrographic studies showed that the minerais biotite and plagioclase, in all investigated mineralizations, played an important role in the chemical reactions occurred in the transformed rocks to the generation of muscovite, cordierite and sillimanite, justifying the input of K to the formation of muscovite, and the release of Na and Ca from plagioclase to the fluid phase. In the São Francisco auriferous mineralization, the results of the Rb-Sr isotopic analysis yielded ages of 645 ± 19 Ma and 596 ± 17 Ma, with both samples, from original and transformed rocks. Two ages, 569 ± 20 Ma. and 554 ± 19 Ma., were obtained with samples frem the transformed rocks domain. These ages suggest that there were two metamorphic pulses during the emplacement of the mineralized shearing zone. The Sm-Nd data yielded TDM ages of 1,31 Ga and 1,26 Ga with 3Nd (0,6 Ga) of -0,26 e -0,40 for the original and final transformed rocks, respectively. In case of the orthogneisses of Caicó Complex, e.g. the Ponta da Serra and Fazenda Simpático mineralizations, the Rb-Sr data did not yield ages with geological significance. In the Ponta da Serra mineralization, the Sm-Nd isotopic data yielded T DM ages of 2,56 Ga and 2,63 Ga to the original rocks and of 2,71 Ga to the mineralized sheared rock, and values of 3Nd (2,0 Ga) between -3,70 e -5,42 to the original and sheared rock, respectively. In the Fazenda Simpático, Sm-Nd data yielded TDM between 2,65 and 2,69 Ga with values of 3Nd (2,0 Ga) between -5,25 e -5,52. Considering the Sm-Nd data, the TDM ages may be admitted as the age of the parental magma extraction, producer of the protoliths of the orthogneisses from Ponta da Serra and Fazenda Simpático mineralizations. The chemical mobility studies showed that in the basement hosted mineralizations, Rb achieved mass while Sr lost mass, as Sm as well as Nd were strongly mobilized. The Sm/Nd ratio remained constant, however, confirming the isochemical character of those elements. In the basement mineralizations, Rb-Sr ages are destituted of geological significance, because of the partial opening of the isotopic system during the tectono-metamorphic transformations. In the tungsten mineralization, the diagram Sm-Nd constructed with the whole-rock data of calcsilicatic and the high-temperature paragenesis (garnet, diopside and iron-pargasitic hornblende) indicated an 631 ± 24 Ma age, while with the whole-rock data and low-temperature paragenesis (vesuvianite, epidote and calcite), a 537 ± 107 Ma age was obtained. These ages, associated with the petrographic observations, suggest that there was a time gap among the hydrothernal events responsible by the formation of the high and low temperature paragenesis in the calcsilicatic rocks mineralized in scheelite

Pirometamorfismo nos arenitos da Formação Açu, Bacia Potiguar, NE do Brasil

Pyrometamorphism results from conditions of high temperatures and very low pressures provoked by the intrusion of hypabyssal basic bodies into sedimentary or metassedimentary hosting rocks. The onshore portion of the Potiguar Basin in NE Brazil offers examples of this type of metamorphism nearby the contacts of Paleogene to Neogene plugs, sills and dikes of diabases and basalts crosscutting sandstones, siltstones and shales of the Açu Formation (Albian-Cenomanian). The thermal effects over these rocks are reflected on textures and minerals assemblages that characterize the sanidinite facies of metamorphism, often with partial melting of the feldspathic and mica-rich matrix. The liquid formed is potassic and peraluminous, with variably colored rhyolitic glass (colorless, yellow, brown) comprising microcrystals of tridymite, sanidine and clinoenstatite, besides residual detrital clasts of quartz and rarely zircon, staurolite and garnet. Lenses of shale intercalated within the sandstones display crystallites of Fe-cordierite (sekaninaite), mullite, sanidine, armalcolite (Fe-Ti oxide) and brown spinel. The rocks formed due to the thermal effect of the intrusions are called buchites for which two types are herein described: a light one derived from feldspathic sandstone and siltstone protoliths; and a dark one derived from black shale protoliths. Textures indicating partial melting and minerals such as sanidine, mullite, tridymite and armalcolite strongly demonstrate that during the intrusion of the basic bodies the temperature reached 1,000-1,150°C, and was followed by quenching. Cooling of the interstitial melts has as consequences the closure of pores and decrease of the permeability of the protolith, which varies from about 17-11% in the unaffected rocks to zero in the thermally modified types. Although observed only at contacts and over small distances, the number of basic intrusions hosted within the Potiguar Basin in both onshore and offshore portions leaves opened the possibility of important implications of the thermal effects over the hydrocarbon exploration in this area as well in other Cretaceous and Paleozoic basins in Brazil

MATHEMATICA notebook for computing tetrahedral finite element shape functions and matrices for the Helmholtz equation

A MATHEMATICA notebook to compute the elements of the matrices which arise in the solution of the Helmholtz equation by the finite element method (nodal approximation) for tetrahedral elements of any approximation order is presented. The results of the notebook enable a fast computational implementation of finite element codes for high order simplex 3D elements reducing the overheads due to implementation and test of the complex mathematical expressions obtained from the analytical integrations. These matrices can be used in a large number of applications related to physical phenomena described by the Poisson, Laplace and Schrodinger equations with anisotropic physical properties.

An exact equation for the free surface of a fluid in a porous medium

We study the problem of the evolution of the free surface of a fluid in a saturated porous medium, bounded from below by a. at impermeable bottom, and described by the Laplace equation with moving-boundary conditions. By making use of a convenient conformal transformation, we show that the solution to this problem is equivalent to the solution of the Laplace equation on a fixed domain, with new variable coefficients, the boundary conditions. We use a kernel of the Laplace equation which allows us to write the Dirichlet-to-Neumann operator, and in this way we are able to find an exact differential-integral equation for the evolution of the free surface in one space dimension. Although not amenable to direct analytical solutions, this equation turns out to allow an easy numerical implementation. We give an explicit illustrative case at the end of the article.

Políticas públicas e voz do professor: caracterização das leis brasileiras

OBJETIVO: Caracterizar as leis sobre saúde vocal publicadas em todo território nacional até o ano de 2006. MÉTODOS: Foram feitas buscas da documentação em sites oficiais, assim como um questionário elaborado pelas autoras foi divulgado no meio fonoaudiológico, por correio eletrônico, para captar o maior número de leis possível. Obtiveram-se 22 documentos que foram analisados quanto ao raio de abrangência, ações propostas, natureza dessas ações, público-alvo, secretarias envolvidas, iniciativa e promulgação das leis. Tais dados foram analisados de maneira absoluta (numérica) e relativa (percentualmente). RESULTADOS: Os documentos são, em sua maioria, leis de abrangência estadual, mais numerosas na região sudeste, propostas pelo poder legislativo, cuja viabilização compete a uma parceria entre secretarias de saúde e educação estaduais. As ações propostas, de modo geral, preconizam a implementação de assistência preventiva por meio de cursos teórico-práticos (90,91%), com periodicidade anual, ministrados por fonoaudiólogos, com a ressalva de que será oferecido, ao professor com distúrbio vocal, acesso ao tratamento fonoaudiológico e/ou médico (77,27%). em apenas três documentos (13,64%) avança-se para além de cursos, com propostas de ações de promoção à reabilitação, inclusive com menção ao ambiente de trabalho. Dois deles (9,09%) consideram os direitos do professor trabalhador. CONCLUSÃO: Levando-se em conta o grande número de casas legislativas no Brasil, poucas são as leis propostas a favor da saúde do professor, especialmente em relação à voz. Além disso, para que sejam aplicadas e transformadas em programas de saúde vocal, tais iniciativas devem partir de competência constitucional própria, a fim de garantir os recursos financeiros necessários para a sua viabilização.

Comparação entre análises para permanência no rebanho de vacas Nelore utilizando modelo linear e modelo de limiar

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Arquitetura multiprocessada e reconfigurável para a síntese de redes de Petri em hardware

Uma arquitetura reconfigurável e multiprocessada para a implementação física de Redes de Petri foi desenvolvida em VHDL e mapeada sobre um FPGA. Convencionalmente, as Redes de Petri são transformadas em uma linguagem de descrição de hardware no nível de transferências entre registradores e um processo de síntese de alto nível é utilizado para gerar as funções booleanas e tabelas de transição de estado para que se possa, finalmente, mapeá-las num FPGA (Morris et al., 2000) (Soto and Pereira, 2001). A arquitetura proposta possui blocos lógicos reconfiguráveis desenvolvidos exclusivamente para a implementação dos lugares e das transições da rede, não sendo necessária a descrição da rede em níveis de abstração intermediários e nem a utilização de um processo de síntese para realizar o mapeamento da rede na arquitetura. A arquitetura permite o mapeamento de modelos de Redes de Petri com diferenciação entre as marcas e associação de tempo no disparo das transições, sendo composta por um arranjo de processadores reconfiguráveis, cada um dos quais representando o comportamento de uma transição da Rede de Petri a ser mapeada e por um sistema de comunicação, implementado por um conjunto de roteadores que são capazes de enviar pacotes de dados de um processador reconfigurável a outro. A arquitetura proposta foi validada num FPGA de 10.570 elementos lógicos com uma topologia que permitiu a implementação de Redes de Petri de até 9 transições e 36 lugares, atingindo uma latência de 15,4ns e uma vazão de até 17,12GB/s com uma freqüência de operação de 64,58MHz.