Temperature controlled light-emitting diode lamp for photovoltaic rural applications

In recent years, interest in light-emitting diode (LED) lighting has been growing because of its high efficacy, lifetime and ruggedness. This paper proposes a better adaptation of LED lamps to the technical requirements of photovoltaic lighting domestic systems, whose main quality criteria are reliability and that behave as voltage power supplies. As the key element of reliability in LED lamps is temperature, a solution is proposed for driving LED lamps using voltage sources, such as photovoltaic system batteries, with a control architecture based on pulse width modulation signal that regulates the current applied according to the LED lamp temperature. A prototype of the LED lamp has been implemented and tested to show its good performance at different temperatures and at different battery voltages.

Dynamical characterization of monolithic MOPAs emitting at 1.5 μ�m

Eye-safety requirements in important applications like LIDAR or Free Space Optical Communications make specifically interesting the generation of high power, short optical pulses at 1.5 um. Moreover, high repetition rates allow reducing the error and/or the measurement time in applications involving pulsed time-of-flight measurements, as range finders, 3D scanners or traffic velocity controls. The Master Oscillator Power Amplifier (MOPA) architecture is an interesting source for these applications since large changes in output power can be obtained at GHz rates with a relatively small modulation of the current in the Master Oscillator (MO). We have recently demonstrated short optical pulses (100 ps) with high peak power (2.7 W) by gain switching the MO of a monolithically integrated 1.5 um MOPA. Although in an integrated MOPA the laser and the amplifier are ideally independent devices, compound cavity effects due to the residual reflectance at the different interfaces are often observed, leading to modal instabilities such as self-pulsations.

Analysis of mode competition in a monolithic master- oscillator power‐amplifier emitting at 1.5 μm

The optical and radio-frequency spectra of a monolithic master-oscillator power-amplifier emitting at 1.5 ?m have been analyzed in a wide range of steady-state injection conditions. The analysis of the spectral maps reveals that, under low injection current of the master oscillator, the device operates in two essentially different operation modes depending on the current injected into the amplifier section. The regular operation mode with predominance of the master oscillator alternates with lasing of the compound cavity modes allowed by the residual reflectance of the amplifier front facet. The quasi-periodic occurrence of these two regimes as a function of the amplifier current has been consistently interpreted in terms of a thermally tuned competition between the modes of the master oscillator and the compound cavity modes.

Estudio de la fiabilidad de diodos LEDs rojos mediante ensayos acelerados

El objetivo de este Proyecto Final de Carrera es la realización de un ensayo de fiabilidad de componentes electrónicos, más concretamente de diodos LED, con el fin de estudiar su comportamiento a lo largo del tiempo de vida. Debido a la larga duración de los LEDs, un ensayo de este tipo podría durar años, por lo que es necesario realizar un ensayo acelerado que acorte significativamente el tiempo del experimento, para ello, han de someterse a esfuerzos mayores que en condiciones normales de funcionamiento. En la actualidad, los LEDs son usados en infinidad de aplicaciones, debido a sus múltiples ventajas respecto a otros sistemas de iluminación o señalización convencionales. En numerosos casos se utilizan en el exterior, soportando cambios de temperaturas y de humedad elevados, de ahí, la importancia de realizar ensayos de fiabilidad, que muestren sus posibles causas de fallo, los efectos que producen estos fallos y los aspectos de diseño, fabricación y mantenimiento que puedan afectarles. Como consecuencia del envejecimiento de los LEDs, pueden mostrar una reducción en el flujo luminoso y un empeoramiento de las propiedades cromáticas. Los LEDs utilizados en este Proyecto son de AlInGaP, rojos, de alta luminosidad. Para acelerar el ensayo, se utilizará una cámara climática que simule unas condiciones ambientales determinadas, en concreto, 85º C y 85% HR. Además, se realiza una monitorización periódica, siendo necesaria la utilización de un sistema automático de medida diseñado en LabVIEW, el cual, de manera simultánea realizará medidas y gestionará la inyección de corriente a los LEDs mientras se encuentren en el interior de la cámara climática. Se fabrican dos placas con 4 tiras de LEDs para inyectar un nivel de corriente diferente en cada una y así poder comparar la degradación en función de este parámetro. Fuera de la cámara climática se van a medir las curvas características de tensióncorriente de cada LED a una temperatura ambiente constante, fijada por un módulo Peltier. También se realizarán medidas de potencia luminosa y de espectro de emisión. Se analizarán los resultados obtenidos de cada una de las medidas y se realizará un estudio de fiabilidad y del proceso de degradación sufrido por los LEDs. Este PFC se puede dividir en las siguientes fases de trabajo, siendo el ensayo la parte más larga en el tiempo: · Búsqueda de bibliografía, documentación y normas aplicables. · Familiarización con los equipos y software, estudiando el manejo y funcionamiento de la cámara climática temperatura-humedad y el software a aplicar (LabVIEW y software del espectrómetro). · Desarrollo del hardware y sistemas necesarios para la realización del ensayo. · Realización del ensayo. · Análisis de resultados. ABSTRACT. The objective of this end of degree project is conducting an essay reliability of electronic components, more concretely LEDs, in order to study their behavior throughout its lifespan. Due to the long duration of the LEDs, a essay of this type could last for years, so it is necessary to perform an accelerated essay which significantly shorten the time of the experiment, testing should be subjected to greater efforts than in normal operation. Today, LEDs are used in many applications due to its many advantages over other conventional lighting systems or signaling. In numerous cases are used on the outside, enduring high changes in temperature and humidity, hence the importance of reliability essays, showing the possible causes of failure, the effects produced by these failures and aspects of design, manufacturing and maintenance that may affect them. As a result of the ageing of the LEDs, they may show a reduction in light output and a worsening of the chromatic properties. The LEDs used in this project are AlInGaP, red and high brightness. To speed up the essay will be used a climatic chamber to simulate specific environmental conditions, specifically 85 ° C and 85 % RH. In addition, is pe rformed a periodic monitoring using an automatic measurement system designed in LabVIEW , which , simultaneously will performed measurements and will manage the injection current to the LEDs while are inside of the climatic chamber. 4 strips of LEDs are created to inject a different level of current in each, so can compare the degradation in terms of this parameter. Out of the climatic chamber are obtained the characteristic curves of voltage-current of each LED at a constant room temperature, set by a Peltier module. Also, measures light power and the emitted spectrum. The results of each of the measures and a reliability study and degradation suffered by the LEDs will be discussed. This PFC can be divided into the following steps, the essay being the longest part: • Search bibliography, documentation and standards. • Familiarization with equipment and software, studying the management and the operation of the temperature-humidity environmental chamber and applying software (LabVIEW applications and spectrometer software). • Development of hardware and systems necessary for the conduct of the essay. • Carrying out the essay. • Analysis of results.

3-D modeling of perimeter recombination in GaAs diodes and its influence on concentrator solar cells

This paper describes a complete modelling of the perimeter recombination of GaAs diodes which solves most unknowns and suppresses the limitations of previous models. Because of the three dimensional nature of the implemented model, it is able to simulate real devices. GaAs diodes on two epiwafers with different base doping levels, sizes and geometries, namely square and circular are manufactured. The validation of the model is achieved by fitting the experimental measurements of the dark IV curve of the manufactured GaAs diodes. A comprehensive 3-D description of the occurring phenomena affecting the perimeter recombination is supplied with the help of the model. Finally, the model is applied to concentrator GaAs solar cells to assess the impact of their doping level, size and geometry on the perimeter recombination.

Absorption cross-sections of hole polarons in glassy and β-phase polyfluorene

Absorption induced by electrochemically injected holes is studied in poly-9,9-dioctylfluorene (PFO) films. Injected charges form positive polarons which are delocalised over four fluorene units in the glassy phase and about seven fluorene units in its β-phase. Polaron absorption cross-sections at the 640 nm peak are similar to the published values of chemically reduced oligofluorenes in solution. The absorption cross-section of polaron in the β-phase at 470 nm is about eight times smaller than the stimulated emission cross-section derived from published data. This indicates that β-phase-rich PFO is an attractive candidate for a light-emitting layer in double-heterostructure organic laser diodes.

Gamma-emitting radionuclides in tuna samples from the Tokyo Central Fish Market, 1962.

Mode of access: Internet.

The development of a fast neutron spectrometer using silicon surface barrier diodes /

"Published August 1961."

Permanent damage effects of nuclear radiation on the X-band performance of silicon Schottky-barrier microwave mixer diodes /

S/N 003-003-01635-7.

Basic theory and application of tunnel diodes.

Mode of access: Internet.

Optical autocorrelator that uses a surface-emitting second-harmonic generator on (211)B GaAs

An optical autocorrelator grown on a (211)B GaAs substrate that uses visible surface-emitted second-harmonic generation is demonstrated. The (211)B orientation needs TE mode excitation only, thus eliminating the problem of the beating between the TE and TM modes that is required for (100)-grown devices; it also has the advantage of giving higher upconversion efficiency than (111) growth. Values of waveguide loss and the difference in the effective refractive index between the TE(0) and TE(1) modes were also obtained from the autocorrelation experiment.

Gain switching of an external cavity grating-coupled surface emitting laser with wide tunability

The gain-switched, single frequency operation of an external cavity grating-coupled surface emitting laser with a wavelength tuning range of 100 nm was presented. The light in the grating section was coupled out of the laser at a specific angle to the surface of the device. Analysis showed that within the driving current range, lasing in the device only occurred when the external cavity was properly aligned.