Interaction between widening of diameter of abdominal aorta and cardiovascular risk factors and atherosclerosis burden.

The aim of this study was to investigate influence of traditional cardiovascular risk factors (CVRF) and subclinical atherosclerosis (ATS) burden on early stages of abdominal aortic diameter (AAD) widening among adults. 2,052 consecutive patients (P) (39 % women), mean age 52 ± 13 years, were prospectively screened for CVRF, ATS, and AAD. B-mode ultrasound was used to evaluate the largest AAD and to detect carotid and femoral atherosclerotic plaques. Mean AAD was 15.2 ± 2.8 mm. Atherosclerotic plaques were detected in 71 % of patients. Significant univariate correlation between AAD, traditional CVRF, and ABS was found. However, multiple regression analysis showed that only seven of them were significantly and weakly correlated with AAD (R² = 0.27, p < 0.001). On the other hand, a multivariate logistic analysis was used to evaluate CVRF impact on enlarged AAD ≥25 mm (EAAD) as compared to those with AAD <25 mm. These factors did not account for more than 30 % of interaction (R² = 0.30, p = 0.001). Furthermore, despite a large proportion of patients with high number of CVRF, and subclinical ATS, rate of patients with AAD ≥25 mm was low (1 %) and scattered regardless their CHD risk score or ATS burden. In conclusion, these results suggest that although some traditional CVRF and presence of ATS are associated with early stages of EAAD, other determinants still need to be identified for a better understanding of abdominal aortic aneurysm pathogenesis.

Bortezomib(Velcade (R))-Thalidomide-Dexamethasone (VTD) Is Superior to Thalidomide-Dexamethasone (TD) In Patients with Multiple Myeloma (MM) Progressing or Relapsing After Autologous Transplantation.

Introduction: The Thalidomide-Dexamethasone (TD) regimen has provided encouraging results in relapsed MM. To improve results, bortezomib (Velcade) has been added to the combination in previous phase II studies, the so called VTD regimen. In January 2006, the European Group for Blood and Marrow Transplantation (EBMT) and the Intergroupe Francophone du Myélome (IFM) initiated a prospective, randomized, parallel-group, open-label phase III, multicenter study, comparing VTD (arm A) with TD (arm B) for MM patients progressing or relapsing after autologous transplantation. Patients and Methods: Inclusion criteria: patients in first progression or relapse after at least one autologous transplantation, including those who had received bortezomib or thalidomide before transplant. Exclusion criteria: subjects with neuropathy above grade 1 or non secretory MM. Primary study end point was time to progression (TTP). Secondary end points included safety, response rate, progression-free survival (PFS) and overall survival (OS). Treatment was scheduled as follows: bortezomib 1.3 mg/m2 was given as an i.v bolus on Days 1, 4, 8 and 11 followed by a 10-Day rest period (days 12 to 21) for 8 cycles (6 months) and then on Days 1, 8, 15, 22 followed by a 20-Day rest period (days 23 to 42) for 4 cycles (6 months). In both arms, thalidomide was scheduled at 200 mg/Day orally for one year and dexamethasone 40 mg/Day orally four days every three weeks for one year. Patients reaching remission could proceed to a new stem cell harvest. However, transplantation, either autologous or allogeneic, could only be performed in patients who completed the planned one year treatment period. Response was assessed by EBMT criteria, with additional category of near complete remission (nCR). Adverse events were graded by the NCI-CTCAE, Version 3.0.The trial was based on a group sequential design, with 4 planned interim analyses and one final analysis that allowed stopping for efficacy as well as futility. The overall alpha and power were set equal to 0.025 and 0.90 respectively. The test for decision making was based on the comparison in terms of the ratio of the cause-specific hazards of relapse/progression, estimated in a Cox model stratified on the number of previous autologous transplantations. Relapse/progression cumulative incidence was estimated using the proper nonparametric estimator, the comparison was done by the Gray test. PFS and OS probabilities were estimated by the Kaplan-Meier curves, the comparison was performed by the Log-Rank test. An interim safety analysis was performed when the first hundred patients had been included. The safety committee recommended to continue the trial. Results: As of 1st July 2010, 269 patients had been enrolled in the study, 139 in France (IFM 2005-04 study), 21 in Italy, 38 in Germany, 19 in Switzerland (a SAKK study), 23 in Belgium, 8 in Austria, 8 in the Czech republic, 11 in Hungary, 1 in the UK and 1 in Israel. One hundred and sixty nine patients were males and 100 females; the median age was 61 yrs (range 29-76). One hundred and thirty six patients were randomized to receive VTD and 133 to receive TD. The current analysis is based on 246 patients (124 in arm A, 122 in arm B) included in the second interim analysis, carried out when 134 events were observed. Following this analysis, the trial was stopped because of significant superiority of VTD over TD. The remaining patients were too premature to contribute to the analysis. The number of previous autologous transplants was one in 63 vs 60 and two or more in 61 vs 62 patients in arm A vs B respectively. The median follow-up was 25 months. The median TTP was 20 months vs 15 months respectively in arm A and B, with cumulative incidence of relapse/progression at 2 years equal to 52% (95% CI: 42%-64%) vs 70% (95% CI: 61%-81%) (p=0.0004, Gray test). The same superiority of arm A was also observed when stratifying on the number of previous autologous transplantations. At 2 years, PFS was 39% (95% CI: 30%-51%) vs 23% (95% CI: 16%-34%) (A vs B, p=0.0006, Log-Rank test). OS in the first two years was comparable in the two groups. Conclusion: VTD resulted in significantly longer TTP and PFS in patients relapsing after ASCT. Analysis of response and safety data are on going and results will be presented at the meeting. Protocol EU-DRACT number: 2005-001628-35.

Determination of plasma levels of citalopram and its demethylated and deaminated metabolites by gas chromatography and gas chromatography-mass spectrometry.

Sensitive and specific methods based on gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS) for the determination of levels of citalopram, desmethylcitalopram and didesmethylcitalopram in the plasma of patients treated with citalopram are presented, as well as a GC-MS procedure for the assay of the citalopram propionic acid derivative. After addition of a separate internal standard for each drug, liquid-solvent extraction is used to separate the basic compounds from the acid compounds. The demethylated amines are derivatized with trifluoroacetic anhydride, and the acid metabolite with methyl iodide. GC-MS is performed in the electron impact mode, as mass spectrometry by the (positive-ion) chemical ionization mode (methane and ammonia) appeared to be unsuitable. The limits of quantification were 1 ng/ml for citalopram and desmethylcitalopram and 2 ng/ml for the other metabolites. The correlation coefficients for the calibration curves (range 10-500 ng/ml) were &gt; or = 0.999 for all compounds, whether determined by GC or GC-MS.

CE-ESI-TOF/MS for human growth hormone analysis.

CE is a powerful analytical tool used to separate intact biomolecules such as proteins. The coupling of CE with TOF/MS produces a very promising method that can be used to detect and identify proteins in different matrices. This paper describes an efficient, rapid, and simple CE-ESI-TOF/MS procedure for the analysis of endogenous human growth hormone and recombinant human growth hormone without sample preparation. Operational factors were optimized using an experimental design, and the method was successfully applied to distinguish human growth hormone and recombinant human growth hormone in unknown samples.

Bortezomib(Velcade®)-Thalidomide-Dexamethasone (VTD) Is Superior to Thalidomide-Dexamethasone (TD) In Patients with Multiple Myeloma (MM) Progressing or Relapsing After Autologous Transplantation

Introduction: The Thalidomide-Dexamethasone (TD) regimen has provided encouraging results in relapsed MM. To improve results, bortezomib (Velcade) has been added to the combination in previous phase II studies, the so called VTD regimen. In January 2006, the European Group for Blood and Marrow Transplantation (EBMT) and the Intergroupe Francophone du Myélome (IFM) initiated a prospective, randomized, parallel-group, open-label phase III, multicenter study, comparing VTD (arm A) with TD (arm B) for MM patients progressing or relapsing after autologous transplantation. Patients and Methods: Inclusion criteria: patients in first progression or relapse after at least one autologous transplantation, including those who had received bortezomib or thalidomide before transplant. Exclusion criteria: subjects with neuropathy above grade 1 or non secretory MM. Primary study end point was time to progression (TTP). Secondary end points included safety, response rate, progression-free survival (PFS) and overall survival (OS). Treatment was scheduled as follows: bortezomib 1.3 mg/m2 was given as an i.v bolus on Days 1, 4, 8 and 11 followed by a 10-Day rest period (days 12 to 21) for 8 cycles (6 months) and then on Days 1, 8, 15, 22 followed by a 20-Day rest period (days 23 to 42) for 4 cycles (6 months). In both arms, thalidomide was scheduled at 200 mg/Day orally for one year and dexamethasone 40 mg/Day orally four days every three weeks for one year. Patients reaching remission could proceed to a new stem cell harvest. However, transplantation, either autologous or allogeneic, could only be performed in patients who completed the planned one year treatment period. Response was assessed by EBMT criteria, with additional category of near complete remission (nCR). Adverse events were graded by the NCI-CTCAE, Version 3.0.The trial was based on a group sequential design, with 4 planned interim analyses and one final analysis that allowed stopping for efficacy as well as futility. The overall alpha and power were set equal to 0.025 and 0.90 respectively. The test for decision making was based on the comparison in terms of the ratio of the cause-specific hazards of relapse/progression, estimated in a Cox model stratified on the number of previous autologous transplantations. Relapse/progression cumulative incidence was estimated using the proper nonparametric estimator, the comparison was done by the Gray test. PFS and OS probabilities were estimated by the Kaplan-Meier curves, the comparison was performed by the Log-Rank test. An interim safety analysis was performed when the first hundred patients had been included. The safety committee recommended to continue the trial. Results: As of 1st July 2010, 269 patients had been enrolled in the study, 139 in France (IFM 2005-04 study), 21 in Italy, 38 in Germany, 19 in Switzerland (a SAKK study), 23 in Belgium, 8 in Austria, 8 in the Czech republic, 11 in Hungary, 1 in the UK and 1 in Israel. One hundred and sixty nine patients were males and 100 females; the median age was 61 yrs (range 29-76). One hundred and thirty six patients were randomized to receive VTD and 133 to receive TD. The current analysis is based on 246 patients (124 in arm A, 122 in arm B) included in the second interim analysis, carried out when 134 events were observed. Following this analysis, the trial was stopped because of significant superiority of VTD over TD. The remaining patients were too premature to contribute to the analysis. The number of previous autologous transplants was one in 63 vs 60 and two or more in 61 vs 62 patients in arm A vs B respectively. The median follow-up was 25 months. The median TTP was 20 months vs 15 months respectively in arm A and B, with cumulative incidence of relapse/progression at 2 years equal to 52% (95% CI: 42%-64%) vs 70% (95% CI: 61%-81%) (p=0.0004, Gray test). The same superiority of arm A was also observed when stratifying on the number of previous autologous transplantations. At 2 years, PFS was 39% (95% CI: 30%-51%) vs 23% (95% CI: 16%-34%) (A vs B, p=0.0006, Log-Rank test). OS in the first two years was comparable in the two groups. Conclusion: VTD resulted in significantly longer TTP and PFS in patients relapsing after ASCT. Analysis of response and safety data are on going and results will be presented at the meeting.

Iowa Mass Concrete for Bridge Foundation Study - Phase II, Final Report, 2014

The early-age thermal development of structural mass concrete elements has a significant impact on the future durability and longevity of the elements. If the heat of hydration is not controlled, the elements may be susceptible to thermal cracking and damage from delayed ettringite formation. In the Phase I study, the research team reviewed published literature and current specifications on mass concrete. In addition, the team observed construction and reviewed thermal data from the westbound (WB) I-80 Missouri River Bridge. Finally, the researchers conducted an initial investigation of the thermal analysis software programs ConcreteWorks and 4C-Temp&Stress. The Phase II study is aimed at developing guidelines for the design and construction of mass concrete placements associated with large bridge foundations. This phase included an additional review of published literature and a more in-depth investigation of current mass concrete specifications. In addition, the mass concrete construction of two bridges, the WB I-80 Missouri River Bridge and the US 34 Missouri River Bridge, was documented. An investigation was conducted of the theory and application of 4C-Temp&Stress. ConcreteWorks and 4C-Temp&Stress were calibrated with thermal data recorded for the WB I-80 Missouri River Bridge and the US 34 Missouri River Bridge. ConcreteWorks and 4C-Temp&Stress were further verified by means of a sensitivity study. Finally, conclusions and recommendations were developed, as included in this report.

Pituusleikkurin turvaväylät ja koneturvallisuus

Turvallisuuteen liittyvän ohjausjärjestelmän tehtävänä on siirtää ja käsitellä turvallisuuskriittistä tietoa. Esimerkiksi anturin (turvalaitteen) havaitessa vaaravyöhykkeelle pyrkivän ihmisen tulee ensimmäisenä tiedon välittyä ohjausjärjestelmään. Ohjausjärjestelmän on muodostettava saapuneen tiedon perusteella käsky tehonohjauselimille. Tehonohjauselimillä säädellään koneen käyttöenergian syöttöä ja sitä kautta on mahdollista pysäyttää koneen liike ennen mahdollisen vahingon sattumista. Perinteiset turvaratkaisut ovat perustuneet pakkotoimintaisiin releisiin ja kahdennuksiin. Tällämenetelmällä on toteutettu varmatoimintaisia turvaratkaisuja, joissa yksittäiset viat ovat paljastuneet. Nykyisin on kuitenkin yhä enemmän tarvetta integroida turvatoiminnot automaatiojärjestelmään ja toteuttaa turvaratkaisut hajautetuillajärjestelmillä. Hajautetut järjestelmät sisältävät osittain ohjelmoitavien järjestelmien etuja ja haittoja, mutta tuovat mukanaan myös uudenlaisia vikoja. Työn tarkoitus oli selvittää, millaisia rajoituksia koneturvallisuus asettaa paperiteollisuuden pituusleikkurien turvallisuuteen liittyville ohjausjärjestelmille, sekä selvittää turvallisuuteen liittyvien järjestelmien rakennetta ja ominaisuuksia. Tässä työssä tutkittiin AS-i, EsaLan ja ProfiSafe turvajärjestelmiä teknisten tietojen perusteella. Tutkitut järjestelmät ovat erilaisia ja soveltuvat tämän vuoksi hieman erilaisiin kohteisiin. Kaikilla näillä järjestelmillä on kuitenkin mahdollista toteuttaa pituusleikkurin turvaväyläjärjestelmässä riittävä turvallisuuden taso koneturvallisuuden näkökulmasta. Tämä edellyttää oikein tehtyä riskianalyysiä ja oikeita suunnittelumenetelmiä. Teknisten tietojen perusteella otettiin testattavaksi AS-i safety at workja EsaLan:in Compact järjestelmät, joille suoritettiin sähkömagneettiseen yhteensopivuuteen (EMC) ja toiminnallisuuteen liittyviä testejä.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Dynamic arrest in polymer melts: competition between packing and intramolecular barriers

We present molecular dynamics simulations of a simple model for polymer melts with intramolecular barriers. We investigate structural relaxation as a function of the barrier strength. Dynamic correlators can be consistently analyzed within the framework of the mode coupling theory of the glass transition. Control parameters are tuned in order to induce a competition between general packing effects and polymer-specific intramolecular barriers as mechanisms for dynamic arrest. This competition yields unusually large values of the so-called mode coupling theory exponent parameter and rationalizes qualitatively different observations for simple bead-spring and realistic polymers. The systematic study of the effect of intramolecular barriers presented here also establishes a fundamental difference between the nature of the glass transition in polymers and in simple glass formers.

Törmäysystävällisen valaisinpylvään tuotteistaminen

Euroopan unioni on tiukentanut teiden laitteiden ja tukirakenteiden törmäysturvallisuusvaatimuksia. Uuden standardoinnin tarkoituksena on lieventää ajoneuvon kuljettajan ja matkustajan vammojen vakavuutta ajoneuvon törmätessä tielaitteiden pysyviin rakenteisiin. Käytännössä rakenteiden tulee hidastaa ajoneuvon nopeutta hallitusti eri törmäysnopeuksilla, jolloin matkustajaan kohdistuvat kiihtyvyydet eivät aiheuta vakavaa loukkaantumisriskiä. Vuonna 2005 Mikkelin ammattikorkeakoulun YTI-tutkimuskeskus ja Tehomet Oy kehittivät ensimmäisen version törmäysystävällisestä valaisinpylväästä. Tässä diplomityössä tavoitteena oli kehittää aikaisemmin tehdystä versiosta helpommin valmistettava versio sekä parantaa pylvään törmäyskäyttäytymistä. Valmistusmenetelmistä valittiin pultruusio, kuitukelaus, alipaineinjektio ja RTM. Menetelmille suunniteltiin soveltuvat rakenteet ja laskettiin rakenteiden valmistuskustannukset. Pultruusiolla, alipaineinjektiolla ja RTM:11ä valmistettiin koe-erä esitörmäyskokeita varten. Esitörmäyskokeiden jälkeen valittiin valmistusmenetelmäksi RTM. TKK/Tielaboratorion virallisissa testeissä kehitetylle pylväälle myönnettiin HE2-turvaluokitus. Hanketta jatketaan kehittämällä valmistusprosessia tehokkaammaksi uudistamalla muottitekniikkaa sekä ottamalla käyttöön lujiteaihiot. Tavoitteena on käynnistää tuotanto keväällä 2008. Kehitetty pylväs esitellään kansainvälisillä "Sähkö, Tele, Valo- ja AV 2008"-messuilla Jyväskylän Paviljongissa 6.-8.2.2008.

Farmer-Managed Natural Regeneration Enhances Rural Livelihoods in Dryland West Africa

Declining agricultural productivity, land clearance and climate change are compounding the vulnerability of already marginal rural populations in West Africa. 'Farmer-Managed Natural Regeneration' (FMNR) is an approach to arable land restoration and reforestation that seeks to reconcile sustained food production, conservation of soils and protection of biodiversity. It involves selecting and protecting the most vigorous stems regrowing from live stumps of felled trees, pruning off all other stems, and pollarding the chosen stems to grow into straight trunks. Despite widespread enthusiasm and application of FMNR by environmental management and development projects, to date, no research has provided a measure of the aggregate livelihood impact of community adoption of FMNR. This paper places FMNR in the context of other agroforestry initiatives, then seeks to quantify the value of livelihood outcomes of FMNR. We review published and unpublished evidence about the impacts of FMNR, and present a new case study that addresses gaps in the evidence base. The case study focuses on a FMNR project in the district of Talensi in the semi-arid Upper East Region in Ghana. The case study employs a Social Return on Investment (SROI) analysis, which identifies proxy financial values for non-economic as well as economic benefits. The results demonstrate income and agricultural benefits, but also show that asset creation, increased consumption of wild resources, health improvements and psycho-social benefits created more value in FMNR-adopting households during the period of the study than increases in income and agricultural yields.

Tietoteknisten palveluiden tuottaminen strategisena kumppanuutena - case Rajavartiolaitos

Tutkimuksen tarkoituksena on selvittää laajennettujen transaktiokustannustarkastelun avulla tietoteknisten palveluiden hankintaa strategisena kumppanuutena. Tutkimus kuvaa empiirisen esimerkkitapauksen kautta ulkoistuksen kokonaisvaikuttavuutta eli kumppanuuden hyötyjä ja haittoja asiakkaan kannalta tilanteessa, jossa julkisen sektorin tehtävien uudelleenorganisoinnissa ei ole käytettävissä tehokkaita markkinoita. Kumppanuuden kokonaisvaikuttavuuden elementtien merkitys asiakkaalle on asiakkaan ja palveluntuottajan näkökulmista erilaisia. Asiakas pitää transaktiokustannuksia ja byrokratiahyötyjä tärkeinä. Toimittaja taas koros-taa transaktiohyötyjä ja byrokratiakustannuksia.

Analyzing Carbon Trade Permits in Optimization Framework

The threats caused by global warming motivate different stake holders to deal with and control them. This Master's thesis focuses on analyzing carbon trade permits in optimization framework. The studied model determines optimal emission and uncertainty levels which minimize the total cost. Research questions are formulated and answered by using different optimization tools. The model is developed and calibrated by using available consistent data in the area of carbon emission technology and control. Data and some basic modeling assumptions were extracted from reports and existing literatures. The data collected from the countries in the Kyoto treaty are used to estimate the cost functions. Theory and methods of constrained optimization are briefly presented. A two-level optimization problem (individual and between the parties) is analyzed by using several optimization methods. The combined cost optimization between the parties leads into multivariate model and calls for advanced techniques. Lagrangian, Sequential Quadratic Programming and Differential Evolution (DE) algorithm are referred to. The role of inherent measurement uncertainty in the monitoring of emissions is discussed. We briefly investigate an approach where emission uncertainty would be described in stochastic framework. MATLAB software has been used to provide visualizations including the relationship between decision variables and objective function values. Interpretations in the context of carbon trading were briefly presented. Suggestions for future work are given in stochastic modeling, emission trading and coupled analysis of energy prices and carbon permits.

Alusöljyvahingon seurauksena rantautuvan öljyn lajitteluohjeiston muodostaminen

Työn tärkeimpänä päämääränä oli muodostaa öljyvahinkojätejakeille yksityiskohtaiset ja käytännön olosuhteissa mahdollisimman hyvin toimivat lajitteluohjeet. Lähtökohtana oli se, että edeltävien lajitteluohjeiden soveltuvuutta haluttiin tarkastella useista eri näkökulmista, kuten muodostuvien kustannusten kannalta. Työn muut tavoitteet olivat: jäteastioiden määrän ja laadun selvitys sekä lainsäädännön asettamien rajoitteiden selvittäminen. Riskijäte rajattiin työn ulkopuolelle. Tutkimus toteutettiin pääasiassa kirjallisiin lähteisiin, sähköpostikyselyihin ja puhelinhaastatteluihin perustuvien tietojen avulla. Tärkeimmäksi selvitettäväksi seikaksi osoittautui lajittelusta aiheutuvien kustannusten määrittäminen. Etenkin käsittelykustannuksista saatiin viitteitä optimaalisesta lajitteluvaihtoehdosta. Taloudellisessa tarkastelussa käytiin läpi öljyvahinkojätteiden kulkeutuminen rannalta käsittelyyn saakka, jolloin eri vaihtoehtojen eroavaisuudet saatiin selville. Taloudellisen tarkastelun perusteella paras vaihtoehto oli lajitellun jätteen käsittely siirrettävällä termodesorptiolaitoksella yhdistettynä Kotkan hyötyvoimalaitokseen. Tämän perusteella voidaan päätellä, että öljyinen maa-aines ja öljyinen sekajäte kannattaa käsitellä erillisinä jakeina. Tällöin öljyinen maa-aines ja öljyinen sekajäte kannattaa myös lajitella omiin jakeisiinsa. Keräysastioista on vaikeaa antaa suosituksia ilman riittävän kattavia kenttäkokeita. Taloudellisessa tarkastelussa muoviastiat osoittautuivat edullisimmaksi vaihtoehdoksi. Monissa selvityksissä on öljyvahinkojätteiden käsittelyvaihtoehdoksi valittu Riihimäen Ekokem Oy Ab. Se tuli kuitenkin huomattavasti kalliimmaksi kuin siirrettävän termodesorptiolaitoksen sisältävät laskuesimerkit, joten myös muita vaihtoehtoja kannattaisi harkita. Muita kuin muovisia keräysastioita tulisi vielä testata käytännön öljyntorjuntaharjoituksissa, jotta niiden lopullinen käyttökelpoisuus varmistuu. Harjoitukset tulisi suorittaa mahdollisimman vaihtelevissa sää- ja maasto-olosuhteissa, jotta saadaan tarpeeksi kattavaa tutkimustietoa astioiden soveltuvuudesta.