Lidar uncertainty in complex terrain development of a bias correction methodology

El autor ha trabajado como parte del equipo de investigación en mediciones de viento en el Centro Nacional de Energías Renovables (CENER), España, en cooperación con la Universidad Politécnica de Madrid y la Universidad Técnica de Dinamarca. El presente reporte recapitula el trabajo de investigación realizado durante los últimos 4.5 años en el estudio de las fuentes de error de los sistemas de medición remota de viento, basados en la tecnología lidar, enfocado al error causado por los efectos del terreno complejo. Este trabajo corresponde a una tarea del paquete de trabajo dedicado al estudio de sistemas remotos de medición de viento, perteneciente al proyecto de intestigación europeo del 7mo programa marco WAUDIT. Adicionalmente, los datos de viento reales han sido obtenidos durante las campañas de medición en terreno llano y terreno complejo, pertenecientes al también proyecto de intestigación europeo del 7mo programa marco SAFEWIND. El principal objetivo de este trabajo de investigación es determinar los efectos del terreno complejo en el error de medición de la velocidad del viento obtenida con los sistemas de medición remota lidar. Con este conocimiento, es posible proponer una metodología de corrección del error de las mediciones del lidar. Esta metodología está basada en la estimación de las variaciones del campo de viento no uniforme dentro del volumen de medición del lidar. Las variaciones promedio del campo de viento son predichas a partir de los resultados de las simulaciones computacionales de viento RANS, realizadas para el parque experimental de Alaiz. La metodología de corrección es verificada con los resultados de las simulaciones RANS y validadas con las mediciones reales adquiridas en la campaña de medición en terreno complejo. Al inicio de este reporte, el marco teórico describiendo el principio de medición de la tecnología lidar utilizada, es presentado con el fin de familiarizar al lector con los principales conceptos a utilizar a lo largo de este trabajo. Posteriormente, el estado del arte es presentado en donde se describe los avances realizados en el desarrollo de la la tecnología lidar aplicados al sector de la energía eólica. En la parte experimental de este trabajo de investigación se ha estudiado los datos adquiridos durante las dos campañas de medición realizadas. Estas campañas has sido realizadas en terreno llano y complejo, con el fin de complementar los conocimiento adquiridos en casa una de ellas y poder comparar los efectos del terreno en las mediciones de viento realizadas con sistemas remotos lidar. La primer campaña experimental se desarrollo en terreno llano, en el parque de ensayos de aerogeneradores H0vs0re, propiedad de DTU Wind Energy (anteriormente Ris0). La segunda campaña experimental se llevó a cabo en el parque de ensayos de aerogeneradores Alaiz, propiedad de CENER. Exactamente los mismos dos equipos lidar fueron utilizados en estas campañas, haciendo de estos experimentos altamente relevantes en el contexto de evaluación del recurso eólico. Un equipo lidar está basado en tecnología de onda continua, mientras que el otro está basado en tecnología de onda pulsada. La velocidad del viento fue medida, además de con los equipos lidar, con anemómetros de cazoletas, veletas y anemómetros verticales, instalados en mástiles meteorológicos. Los sensores del mástil meteorológico son considerados como las mediciones de referencia en el presente estudio. En primera instancia, se han analizado los promedios diez minútales de las medidas de viento. El objetivo es identificar las principales fuentes de error en las mediciones de los equipos lidar causadas por diferentes condiciones atmosféricas y por el flujo no uniforme de viento causado por el terreno complejo. El error del lidar ha sido estudiado como función de varias propiedades estadísticas del viento, como lo son el ángulo vertical de inclinación, la intensidad de turbulencia, la velocidad vertical, la estabilidad atmosférica y las características del terreno. El propósito es usar este conocimiento con el fin de definir criterios de filtrado de datos. Seguidamente, se propone una metodología para corregir el error del lidar causado por el campo de viento no uniforme, producido por la presencia de terreno complejo. Esta metodología está basada en el análisis matemático inicial sobre el proceso de cálculo de la velocidad de viento por los equipos lidar de onda continua. La metodología de corrección propuesta hace uso de las variaciones de viento calculadas a partir de las simulaciones RANS realizadas para el parque experimental de Alaiz. Una ventaja importante que presenta esta metodología es que las propiedades el campo de viento real, presentes en las mediciones instantáneas del lidar de onda continua, puede dar paso a análisis adicionales como parte del trabajo a futuro. Dentro del marco del proyecto, el trabajo diario se realizó en las instalaciones de CENER, con supervisión cercana de la UPM, incluyendo una estancia de 1.5 meses en la universidad. Durante esta estancia, se definió el análisis matemático de las mediciones de viento realizadas por el equipo lidar de onda continua. Adicionalmente, los efectos del campo de viento no uniforme sobre el error de medición del lidar fueron analíticamente definidos, después de asumir algunas simplificaciones. Adicionalmente, durante la etapa inicial de este proyecto se desarrollo una importante trabajo de cooperación con DTU Wind Energy. Gracias a esto, el autor realizó una estancia de 1.5 meses en Dinamarca. Durante esta estancia, el autor realizó una visita a la campaña de medición en terreno llano con el fin de aprender los aspectos básicos del diseño de campañas de medidas experimentales, el estudio del terreno y los alrededores y familiarizarse con la instrumentación del mástil meteorológico, el sistema de adquisición y almacenamiento de datos, así como de el estudio y reporte del análisis de mediciones. ABSTRACT The present report summarizes the research work performed during last 4.5 years of investigation on the sources of lidar bias due to complex terrain. This work corresponds to one task of the remote sensing work package, belonging to the FP7 WAUDIT project. Furthermore, the field data from the wind velocity measurement campaigns of the FP7 SafeWind project have been used in this report. The main objective of this research work is to determine the terrain effects on the lidar bias in the measured wind velocity. With this knowledge, it is possible to propose a lidar bias correction methodology. This methodology is based on an estimation of the wind field variations within the lidar scan volume. The wind field variations are calculated from RANS simulations performed from the Alaiz test site. The methodology is validated against real scale measurements recorded during an eight month measurement campaign at the Alaiz test site. Firstly, the mathematical framework of the lidar sensing principle is introduced and an overview of the state of the art is presented. The experimental part includes the study of two different, but complementary experiments. The first experiment was a measurement campaign performed in flat terrain, at DTU Wind Energy H0vs0re test site, while the second experiment was performed in complex terrain at CENER Alaiz test site. Exactly the same two lidar devices, based on continuous wave and pulsed wave systems, have been used in the two consecutive measurement campaigns, making this a relevant experiment in the context of wind resource assessment. The wind velocity was sensed by the lidars and standard cup anemometry and wind vanes (installed on a met mast). The met mast sensors are considered as the reference wind velocity measurements. The first analysis of the experimental data is dedicated to identify the main sources of lidar bias present in the 10 minute average values. The purpose is to identify the bias magnitude introduced by different atmospheric conditions and by the non-uniform wind flow resultant of the terrain irregularities. The lidar bias as function of several statistical properties of the wind flow like the tilt angle, turbulence intensity, vertical velocity, atmospheric stability and the terrain characteristics have been studied. The aim of this exercise is to use this knowledge in order to define useful lidar bias data filters. Then, a methodology to correct the lidar bias caused by non-uniform wind flow is proposed, based on the initial mathematical analysis of the lidar measurements. The proposed lidar bias correction methodology has been developed focusing on the the continuous wave lidar system. In a last step, the proposed lidar bias correction methodology is validated with the data of the complex terrain measurement campaign. The methodology makes use of the wind field variations obtained from the RANS analysis. The results are presented and discussed. The advantage of this methodology is that the wind field properties at the Alaiz test site can be studied with more detail, based on the instantaneous measurements of the CW lidar. Within the project framework, the daily basis work has been done at CENER, with close guidance and support from the UPM, including an exchange period of 1.5 months. During this exchange period, the mathematical analysis of the lidar sensing of the wind velocity was defined. Furthermore, the effects of non-uniform wind fields on the lidar bias were analytically defined, after making some assumptions for the sake of simplification. Moreover, there has been an important cooperation with DTU Wind Energy, where a secondment period of 1.5 months has been done as well. During the secondment period at DTU Wind Energy, an important introductory learning has taken place. The learned aspects include the design of an experimental measurement campaign in flat terrain, the site assessment study of obstacles and terrain conditions, the data acquisition and processing, as well as the study and reporting of the measurement analysis.

On the cup anemometer working condition monitoring

The analysis of the harmonic terms related to the rotational speed of a cup anemometer is a way to detect anomalies such as wear and tear, rotor non-symmetries (rotor damage) or problems at the output signal system. The research already done in this matter at the IDR/UPM Institute is now taken to cup anemometers working on the field. A 1-2 year testing campaign is being carried out in collaboration with Kintech Engineering. 2 Thies First Class Advanced installed at 58 m and 73 m height in a meteorology tower are constantly monitored. The results will be correlated to the anemometer performance evolution studied through several calibrations planned to be performed along the testing campaign.

Plataforma de simulación en Matlab-Simulink de un accionamiento regulado para emular aerogeneradores

En este proyecto se desarrolla un modelo de simulación de un accionamiento controlado que emula el comportamiento de una turbina eólica, el cual se ha llevado a cabo a través del programa para simulación Matlab/Simulink. Su desarrollo se ha estructurado de la siguiente forma: Tras una breve introducción a la energía eólica y a las máquinas eléctricas objeto de estudio en este proyecto, se procede a la caracterización y representación de dichas maquinas dentro de la plataforma de simulación virtual Simulink. Posteriormente se explican posibles estrategias de control de la máquina de inducción, las cuales son aplicadas para la realización de un control de velocidad. Asimismo, se realiza un control vectorial de par de la máquina de inducción de modo que permita un seguimiento efectivo del par de referencia demandado por el usuario, ante distintas condiciones. Finalmente, se añade el modelo de turbina eólica de manera que, definiendo los valores de velocidad de viento, ángulo de paso y velocidad del eje, permite evaluar el par mecánico desarrollado por la turbina. Este modelo se valida comprobando su funcionamiento para diferentes puntos de operación ante diversas condiciones del par de carga. Las condiciones de carga se establecen acoplando al modelo de la turbina, un generador síncrono de imanes permanentes conectado a una carga resistiva. ! II! ABSTRACT In this project, the simulation model of a controlled drive that emulates the behaviour of a wind turbine is developed. It has been carried out through the platform for multidomian simulation called Matlab/Simulink. Its development has been structured as follows: After a brief introduction to the wind energy and the electrical machines studied in this project, these machines are characterized and represented into the virtual simulation platform, Simulink. Subsequently, the possible control strategies for the induction machine are explained and applied in order to carry out a speed control. Additionally, a torque vector control of the induction machine is performed, so as to enable an effective monitoring of the reference torque requested by the user, under different conditions. Finally, the wind turbine model is implemented so as to assess the turbine mechanical torque, after defining the wind speed, the pitch angle and the shaft speed values. This model is validated by testing its functionality for different operating points under various load torques. The load conditions are set up by attaching a permanent magnets synchronous machine, with a resistive load, to the turbine model.

Modelado dinámico y control de maniobras de dispositivos submarinos

Es bien conocido por todos que la Primera Revolución Industrial, que tuvo su inicio en la segunda mitad del Siglo XVIII, conllevó un aumento del uso de los recursos energéticos que no se ha detenido para llegar a los niveles de desarrollo tecnológico, industrial y de calidad de vida, de los que se dispone en la actualidad. A simple vista podría intuirse que para disponer de un mayor nivel tecnológico, industrial, de confort, etc. sea necesario un mayor consumo de energía primaria. La actual generación de energía está principalmente basada en el procesamiento de los diversos compuestos del carbono (hidrocarburos, gases y productos derivados del petróleo), que son contaminantes y además, se agotan. Desde hace unas pocas décadas, la humanidad ha sido consciente que es necesario generar energía a partir de fuentes de origen renovable, y que además resulten menos contaminantes. Así, en la actualidad, se ha llegado a un estado de desarrollo avanzado para la explotación de diversas fuentes de energías como la eólica, a la vez que se comienza a mirar con realismo la posibilidad de explotación de diversas energías de origen marino. Se considera que las energías renovables procedentes de los océanos que se encuentran más desarrolladas tecnológicamente hablando, sin tener en cuenta la energía eólica fuera costa (offshore), son la denominada energía undimotriz o de las olas y la energía de las corrientes marinas, no necesariamente en este orden. El trabajo propuesto en esta Tesis se centra en este último recurso energético y, aunque no se dispone todavía de ningún dispositivo en fase de explotación comercial, la concepción, diseño y desarrollo de dispositivos para la extracción de energía de las corrientes, y su evolución, han sido relativamente rápidos e importantes en estos últimos años. Existen ya diferentes dispositivos en fase de pruebas con resultados muy prometedores. Aunque los dispositivos actuales se encuentran limitados a la explotación energética en zonas de poca profundidad, los diferentes estudios del recurso indican la necesidad de explotar corrientes marinas a mayores profundidades, para lo que se están desarrollando actualmente dispositivos, cuya evolución en lo que a sistemas de fondeo se refiere, está siendo muy parecida a la que se ha producido en los parques eólicos fuera costa, similar a su vez, a la evolución llevada a cabo en las plataformas oceánicas para la explotación de recursos petrolíferos (denominados oil & gas) que se extraen de profundidades cada vez mayores. Las soluciones tecnológicas que resulten válidas han de ser también económicamente viables, y en la actualidad se requiere todavía reducir costos en todas las fases de instalación, explotación y mantenimiento de estos dispositivos, sea cual sea su profundidad de operación. Uno de los focos de estudio para abaratar los costes de explotación en general, pasa por abaratar y reducir los costes en las maniobras necesarias de inmersión (de la superficie del mar a la profundidad de operación) y emersión (de la profundidad de operación a la superficie del mar) de estos dispositivos, para llevar a cabo tareas de mantenimiento in situ, en el mar, y sin necesidad de buques especializados ni de su transporte a tierra. En esta Tesis se propone, en primer lugar, un método para evaluar el ciclo de vida de diversos dispositivos de aprovechamiento de las corrientes marinas. Se evidencia que el coste de la energía así generada sigue siendo no plenamente competitivo, por lo que se requiere avanzar en el abaratamiento de costes, principalmente en la instalación y en su mantenimiento. Para ello se propone como novedad principal, introducir sistemas de control en lazo cerrado para realizar maniobras de instalación y mantenimiento de forma automática. También se aporta un modelo dinámico original y muy sencillo para dispositivos bajo estos movimientos de emersión/inmersión, a partir del cual se han desarrollado los algoritmos de control para el propósito mencionado, que no es otro sino automatizar en todo lo posible las maniobras completas. Los algoritmos de control propuestos han sido validados mediante simulación. Se proponen trayectorias de referencia de movimiento suaves (smooth) similares a las utilizadas en robótica. Estos movimientos de cambios de profundidad en lazo cerrado, combinados con secuencias de movimientos en bucle abierto para cuando el dispositivo interacciona en la superficie libre, han dado lugar a nuevas maniobras completas de instalación y mantenimiento que se presentan en esta Tesis, diferentes a las actuales. Finalmente, y como justificación de la viabilidad económica del método novedoso aportado, se ha realizado un estudio comparativo de los costes de la tecnología propuesta, frente a la tecnología actual. Este nuevo sistema de maniobras automáticas implica un ciclo de vida diferente para los dispositivos de aprovechamiento de la energía de las corrientes, ciclo que se cuantifica a partir de un dispositivo base que ha sido modificado y adaptado para la nueva tecnología propuesta, demostrando su viabilidad tanto técnica como económica. ABSTRACT It’s well known that the First Industrial Revolution started in the second half of the eighteenth century, carried the increasing of the use of energy resource which have not been stopped until reach the present technology, industrial evolution and daily life quality. On the surface, it can be known intuitively that a higher consumption of primary energy resource is demanded for benefiting from a higher technological industrial and daily life level. Today, the generation of energy is mainly based in the processing of carbon products (hydrocarbons, gases and petroleum products) which are pollutants, and additionally, are depleted. From a few decades ago, the humanity is aware the energy should be obtained from renewable resources, which besides, should be cleaner. So, at the present, a technical develop has been gained to exploit several energy source, as wind energy, and, at the same time, the extraction of the marine energy starts to seem as a reality. The renewable marine energies considered more advanced and technically developed, without keeping in mind, the offshore wind energy, are the wave energy and the tidal current energy, not necessarily in that order. This Thesis is focused in this last energy resource, and, although, any device is under commercial operation, the concept, design and develop of this type of devices to extract the tidal current energy and their evolution has been comparatively fast and important the last years. There are several devices under test with promising results. Even through the current devices are limited to lower depth areas, the several studies of the tidal energy resource suggest the need to exploit the marine current at greater depths to what is being developed devices, where their evolution in the anchoring system is being very similar to the evolution performed in the offshore wind farms, which is at the same time, similar to the evolution in the oil and gas exploitation which are extracted to greatest depths. Viable technical solutions should be also viable economically and nowadays the cost in all phases of the project (installation, maintenance and operation) should be decreased whatever the operation depth is. One focus of study to lower the operation cost is the cost decreasing of immersion manoeuvring operations (from sea surface to the operation depth) and immersion manoeuvring operations (from operation depth to the sea surface), therefore the maintenance operations can be performed on – site, in the sea, and no specialized vessels are required to transport the devices from the sea to shore. In this dissertation, firstly is proposed a method to evaluate the life cycle of the tidal energy current devices. It is proved the energy generated by these devices is not fully competitive; therefore, the cost falling is mainly an objective in the installation and the maintenance operations. For that, it is proposed as main novelty, the using of closed loop control systems to perform the automatic installation and manoeuvring operations. It is also contributed with an original and simple dynamic model and for controlling the immersion/emersion movements of these devices, from which the control algorithms are developed in order to automate as much as possible the complete manoeuvring. The control algorithms proposed has been validated by simulations. Reference paths with smooth movements, similar which are used in robotics, are suggested. These movements to change the depth using closed loop control, combined with the sequences in open loop movements when the device is in free surface, have been development for a new complete manoeuvring to installation and maintenance operations which are advanced in this Thesis and they are different to the present manoeuvrings. Finally and as justification of the economic viability of this original method, a comparative cost study between the technology proposed and the current technology is performed. This new automatic manoeuvring system involves a different life cycle for the tidal energy current devices, cycle that is quantified from a base device which has been modified and adapted for the new proposed technology, showing the technical and economic viability.

Aerodinámica experimental de elementos de parques energéticos

La creciente demanda de energía eléctrica y la necesidad de implementar energías no contaminantes hace que las llamadas tecnologías verdes sean cada día más solicitadas. Entre estas tecnologías encontramos la energía solar y la energía eólica; ambas tienen una trayectoria de uso e investigación bastante amplia, sin embargo aún presentan problemas de fondo que impiden dar mayor impulso a su uso. El objetivo de la presente tesis es presentar soluciones a problemas de optimización en campos conversores de energía. Para ello se analizan y resuelven dos problemas por medio de técnicas de aerodinámica experimental: el primero sobre campos de colectores solares y el segundo sobre campos eólicos. Las técnicas de medición utilizadas en aerodinámica, y en el presente trabajo, son: medición de cargas, anemometría de hilo caliente, velocimetría por imagen de partículas y escaneo de presiones; además de un análisis estadístico de los datos. En el primer caso se ensayan experimentalmente colectores solares parabólicos en donde, por cuestiones de seguridad o por protección contra el viento, se utilizan cercas. Éstas modifican el comportamiento del flujo corriente abajo y se ha encontrado que la distancia a la cual se colocan, así como el tipo de cercas (sólida o permeable), modifican las cargas estructurales a las que los colectores están expuestos. Los resultados demuestran que existe una distancia crítica en la cual la presencia de la cerca aumenta la carga en lugar de disminuirla, por lo cual la selección adecuada del parapeto y la distancia a la cual se coloca son de suma importancia para la optimización de la estructura. En el segundo caso se ensaya experimentalmente y simula numéricamente la estela de turbinas eólicas por medio de discos porosos. En donde un disco permeable simula el rotor de una turbina. El disco es capaz de semejar la estela y los efectos que ésta puede causar corriente abajo. Los resultados muestran que seleccionando adecuadamente la porosidad, es posible simular coeficientes de empuje similares a los desarrollados por los aerogeneradores, además la estela y sus efectos son semejantes a los medidos en campo. ABSTRACT The called green energy technologies are increasingly required because of the growing demand for electricity and the need to implement nonpolluting energy. Among the green energy technologies it is found the solar and the wind energy, both have a history of use and fairly extensive research; however they still have problems which limit to give them further impetus to its use. The aim of this thesis is to present solutions to optimization problems in energy harvesting. To this end it is analysed, and solved, two problems by means of techniques in experimental aerodynamics: the first issue with regard to parabolic troughs and the second about wind farms. The measurement techniques commonly used in aerodynamics, and used in this research work, are: measurement of loads, hot wire anemometry, particle image velocimetry and scanning of pressures; where data are collected and then an statistical analysis is done. In the first case it is tested parabolic troughs where, either for security reasons or protection against the wind actions, fences are used. These fences modify the behaviour of flow downstream and it was found that the distance at which they are placed, and the type of fences (solid or permeable) modify the structural loads to which the parabolic troughs are exposed. The results show that there is a critical distance at which the presence of the fence increases the load instead of protecting the parabolic trough, hence making the proper selection of the parapet and the distance at which it stands are paramount for the optimization of the structure. In the second case it is tested, experimentally and numerically, the wake of wind turbines by means of porous disks; where the permeable disc simulates a turbine rotor. The disc is able to mimic the wake and the effects that it can cause downstream. The results show that by properly selecting the porosity, it is possible to simulate drag coefficients similar to those developed by wind turbines; moreover the porous disk wake and its effects are similar to those measured on field.

A panel method free-wake code for aeroelastic rotor predictions

A panel method free-wake model to analyse the rotor flapping is presented. The aerodynamic model consists of a panel method, which takes into account the three-dimensional rotor geometry, and a free-wake model, to determine the wake shape. The main features of the model are the wake division into a near-wake sheet and a far wake represented by a single tip vortex, and the modification of the panel method formulation to take into account this particular wake description. The blades are considered rigid with a flap degree of freedom. The problem solution is approached using a relaxation method, which enforces periodic boundary conditions. Finally, several code validations against helicopter and wind turbine experimental data are performed, showing good agreement

Efeitos da soldagem por laser de fibra de Yb na microestrutura do compósito A356/SiCp

Materiais compósitos são projetados e fabricados para várias aplicações de alto desempenho, incluindo componentes para os segmentos automobilístico, aeroespacial, aeronáutico, naval, de defesa, de óleo e gás, energia eólica e até equipamentos esportivos. Porém, a união por soldagem de Compósitos de Matriz Metálica de Alumínio (Al-CMM) ainda é um grande obstáculo para a maior disseminação desta classe de materiais estruturais. As mudanças microestruturais decorrentes do ciclo de soldagem e/ou do tratamento térmico afetam sensivelmente as propriedades mecânicas e físico-químicas finais da junta e do metal base nas proximidades de mesma, daí a importância de se estudar a evolução microestrutural que prospera nestas etapas. O presente trabalho caracterizou a microestrutura do compósito liga-A356/SiCp soldado por laser de fibra de Itérbio, empregando-se nessa tarefa técnicas de microscopia óptica, radiografia e microscopia eletrônica de varredura, assim como difração de raios-X e de elétrons retroespalhados, ensaio instrumentado de dureza e microtomografia computadorizada. O foco das análises realizadas restringiu-se à geometria dos cordões de solda, à expulsão de SiC particulado da zona soldada, à volatilização de elementos químicos da poça de soldagem, à formação de precipitados fragilizantes de Al4SiC4 em formato de agulhas no cordão de solda e à determinação das regiões com concentração de poros, todos estes fenômenos tendo efeitos nocivos, em maior ou menor extensão, no desempenho global da junta do Al-CMM soldada a laser, notadamente em suas propriedades mecânicas e eletroquímicas.

A integração da indústria de energia elétrica na América do Sul: análise dos modelos técnicos e de regulamentação.

Os recursos energéticos naturais não estão distribuídos uniformemente pelo globo terrestre, e são raros os países que os têm na quantidade e na qualidade que necessitam para atender as suas necessidades. Ante a essa realidade, o comércio de energéticos tem sido a forma principal de acesso dos países que não os dispõem em relação as suas necessidades. Esse comércio, que muitas vezes é regido por tratados ou acordos firmados entre países ou blocos econômicos regionais, diversificou-se, traspassou fronteiras e, atualmente, tornou-se um item significativo nas pautas de exportações de vários países. A evolução desse comércio tem a favor a alternativa de integração por meio de interconexões estratégicas de redes e da constituição de mercados comuns, que viabilizam a exploração do potencial de complementariedade energética de forma mais racional. Diante desse contexto, esta dissertação apresenta um estudo exploratório que avalia o estado da arte da integração energética sul-americana e faz análises dos modelos técnicos, das regulamentações, das regulações regionais e multilaterais estabelecidas pelos blocos econômicos sul-americanos e pela Organização Mundial do Comércio. De forma complementar, o estudo verifica e apresenta os fatores que podem comprometer o avanço e a instituição de um futuro mercado comum de energia no continente, conclui pela viabilidade do prosseguimento de ações em prol da ampliação da integração da indústria de energia elétrica na América do Sul e tece recomendações. Os resultados e as recomendações deste trabalho oferecem um embasamento procedimental para a gestão e a atuação institucional dos envolvidos no processo de integração energética da indústria de energia elétrica da região sul americana.

The Superagency Solution

In many parts of the country, hydraulic fracturing has brought energy development onto people’s doorsteps. Efforts by local governments to employ traditional land use mechanisms to study and mitigate some of the impacts of these latest intrusions have erupted into battles over the scope of statewide agencies’ control. Forgotten in this fray are many renewable energy resources. As a general rule, they are not subject to statewide oversight, and consequently renewable energy providers must navigate the myriad of siting and permitting requirements of local jurisdictions. For several years, scholars have urged more statewide renewable energy siting procedures to level the playing field. California is the national leader in renewable energy deployment, yet its statewide energy commission does not have jurisdiction over the siting of photovoltaic solar or wind energy plants. This article explores when statewide siting is beneficial and when it may be contraindicated, making a case for consolidation of all large-scale siting under the purview of California’s “superagency,” the California Energy Commission.

Geothermal Electricity Generation in Colorado: Actual and Perceived Obstacles to Greater Implementation

The objective of this paper is to provide an analysis of the potential and obstacles to the development of geothermal energy resources in Colorado. Geothermal energy is the only renewable resource that can provide base-load electricity. While Colorado has significant geothermal energy potential, there are no such power plants. Layers of federal and state laws and regulations represent one barrier to further geothermal development. Transmission constraints represent another major barrier. High exploration and construction costs along with high-risk profiles for geothermal projects form another major barrier. Perceived barriers such as misunderstanding the impacts, risks, and benefits of geothermal energy hinder further development. Recommendations are provided to help overcome these obstacles.

The Composition of Holocene Aeolianites; Western Eyre Peninsula, Great Australian Bight, South Australia

The Australian southern continental margin is the world’s largest site of cool-water carbonate deposition, and the Great Australian Bight is its largest sector. The Eyre Peninsula is fringed by coastal beaches with aeolianites and marks the eastern edge of the Great Australian Bight. Five shoreline transects of varying lengths spanned a 150km longitudinal distance and at each the intertidal, beach, dune and secondary dune environments were sampled, for a total of 18 samples. Sediments are a mixture of modern, relict, and Cenozoic carbonates, and quartz grains. Carbonate aeolianites on the western Eyre Peninsula are mostly composed of modern carbonate grains: predominantly molluscs (23-33%) and benthic foraminifera (10-26%), locally abundant coralline algae (3-28%), echinoids (2-22%), and bryozoans (2-14%). Cenozoic grain abundance ranges from 1-6% whereas relict grain abundance ranges from 0-17%. A southward increase in bryozoan particles correlates with a nutrient element abundance and decrease in temperature due to a large seasonal coastal upwelling system that drives 2-3 major upwelling events per year, bringing cold, nutrient rich, Sub-Antarctic Surface Water (<12°C) onto the shelf. In southern, mostly wind protected locations, the beach and dune sediment compositions are similar, indicating that wind energy has successfully carried all sediment components of the beach into the adjacent dunes. In northern, exposed locations, the composition is not the same everywhere, and trends indicate that relative wind energy has the ability to impact grain composition through preferential wind transport. Aeolianite composition is therefore a function of both upwelling and the degree of coastal exposure.

Russia's best ally: The situation of the Russian oil sector and forecast for its future. OSW Study 39/2012

Oil is a strategic raw material for Russia and one of fundamental significance for the functioning of the state and its future. Taxes on oil production and exports are the most important source of state budget revenues which guarantee Russia maintains its political and economic stability. Russia is building its international position on the basis of its vast raw material and energy potential. While a great number of various publications have been devoted to Russian gas and Gazprom, surprisingly little research has been done into the present condition and possible future developments of the Russian oil sector, despite the fact that oil has and will have a much greater impact than gas on the functioning and the future of Russia. The main objective of this text is to describe the present situation of the Russian oil sector, its problems and the challenges it is posing, as well as the government’s policy towards this key branch of the Russian economy. This will be an introduction to an attempt to answer to the questions about the possible future production and the export levels of Russian oil, also broken down into the European and Asian directions.

Speakers and consultants : listing by area of expertise /

Cover title.

Resonant cavity Fibre Bragg grating sensor interrogation

This thesis presents a novel high-performance approach to time-division-multiplexing (TDM) fibre Bragg grating (FBG) optical sensors, known as the resonant cavity architecture. A background theory of FBG optical sensing includes several techniques for multiplexing sensors. The limitations of current wavelength-division-multiplexing (WDM) schemes are contrasted against the technological and commercial advantage of TDM. The author’s hypothesis that ‘it should be possible to achieve TDM FBG sensor interrogation using an electrically switched semiconductor optical amplifier (SOA)’ is then explained. Research and development of a commercially viable optical sensor interrogator based on the resonant cavity architecture forms the remainder of this thesis. A fully programmable SOA drive system allows interrogation of sensor arrays 10km long with a spatial resolution of 8cm and a variable gain system provides dynamic compensation for fluctuating system losses. Ratiometric filter- and diffractive-element spectrometer-based wavelength measurement systems are developed and analysed for different commercial applications. The ratiometric design provides a low-cost solution that has picometre resolution and low noise using 4% reflective sensors, but is less tolerant to variation in system loss. The spectrometer design is more expensive, but delivers exceptional performance with picometre resolution, low noise and tolerance to 13dB system loss variation. Finally, this thesis details the interrogator’s peripheral components, its compliance for operation in harsh industrial environments and several examples of commercial applications where it has been deployed. Applications include laboratory instruments, temperature monitoring systems for oil production, dynamic control for wind-energy and battery powered, self-contained sub-sea strain monitoring.

Thermochemical conversion of Brewers Spent Grain combined with catalytic reforming of pyrolysis vapours

The brewing process is an energy intensive process that uses large quantities of heat and electricity. To produce this energy requires a high, mainly fossil fuel consumption and the cost of this is increasing each year due to rising fuel costs. One of the main by-products from the brewing process is Brewers Spent Grain (BSG), an organic residue with very high moisture content. It is widely available each year and is often given away as cattle feed or disposed of to landfill as waste. Currently these methods of disposal are also costly to the brewing process. The focus of this work was to investigate the energy potential of BSG via pyrolysis, gasification and catalytic steam reforming, in order to produce a tar-free useable fuel gas that can be combusted in a CHP plant to develop heat and electricity. The heat and electricity can either be used on site or exported. The first stage of this work was the drying and pre-treatment of BSG followed by characterisation to determine its basic composition and structure so it can be evaluated for its usefulness as a fuel. A thorough analysis of the characterisation results helps to better understand the thermal behaviour of BSG feedstock so it can be evaluated as a fuel when subjected to thermal conversion processes either by pyrolysis or gasification. The second stage was thermochemical conversion of the feedstock. Gasification of BSG was explored in a fixed bed downdraft gasifier unit. The study investigated whether BSG can be successfully converted by fixed bed downdraft gasification operation and whether it can produce a product gas that can potentially run an engine for heat and power. In addition the pyrolysis of BSG was explored using a novel “Pyroformer” intermediate pyrolysis reactor to investigate the behaviour of BSG under these processing conditions. The physicochemical properties and compositions of the pyrolysis fractions obtained (bio-oil, char and permanent gases) were investigated for their applicability in a combined heat power (CHP) application.