User-centric product derivation in software product lines

Software Product Line (SPL) engineering aims at achieving efficient development of software products in a specific domain. New products are obtained via a process which entails creating a new configuration specifying the desired product’s features. This configuration must necessarily conform to a variability model, that describes the scope of the SPL, or else it is not viable. To ensure this, configuration tools are used that do not allow invalid configurations to be expressed. A different concern, however, is making sure that a product addresses the stakeholders’ needs as best as possible. The stakeholders may not be experts on the domain, so they may have unrealistic expectations. Also, the scope of the SPL is determined not only by the domain but also by limitations of the development platforms. It is therefore possible that the desired set of features goes beyond what is possible to currently create with the SPL. This means that configuration tools should provide support not only for creating valid products, but also for improving satisfaction of user concerns. We address this goal by providing a user-centric configuration process that offers suggestions during the configuration process, based on the use of soft constraints, and identifying and explaining potential conflicts that may arise. Suggestions help mitigating stakeholder uncertainty and poor domain knowledge, by helping them address well known and desirable domain-related concerns. On the other hand, automated conflict identification and explanation helps the stakeholders to understand the trade-offs required for realizing their vision, allowing informed resolution of conflicts. Additionally, we propose a prototype-based approach to configuration, that addresses the order-dependency issues by allowing the complete (or partial) specification of the features in a single step. A subsequent resolution process will then identify possible repairs, or trade-offs, that may be required for viabilization.

Implementation of membrane processes for improvement of the detection of food contaminants

The EM3E Master is an Education Programme supported by the European Commission, the European Membrane Society (EMS), the European Membrane House (EMH), and a large international network of industrial companies, research centres and universities (http://www.em3e.eu)

Customer service process optimization at Sonae e MC

Sonae MC is constantly innovating and keeping up with the new market trends, being increasingly focused on E-commerce due to its growing importance. In that area, a telephone line is available to support customers with their problems. However, rare were the cases in which those problems were solved in the first contact. Therefore, the goal of this work was to reengineer these processes to improve the service performance and consequently the customer’s satisfaction. Following an evolutionary approach, improvement opportunities were suggested and if correctly implemented the cases resolution time could decrease 1 day and Sonae MC will save €7.750 per month.

Thermal conditions affecting heat transfer in FDM/FFE: a contribution towards the numerical modelling of the process

The performance of parts produced by Free Form Extrusion (FFE), an increasingly popular additive manufacturing technique, depends mainly on their dimensional accuracy, surface quality and mechanical performance. These attributes are strongly influenced by the evolution of the filament temperature and deformation during deposition and solidification. Consequently, the availability of adequate process modelling software would offer a powerful tool to support efficient process set-up and optimisation. This work examines the contribution to the overall heat transfer of various thermal phenomena developing during the manufacturing sequence, including convection and radiation with the environment, conduction with support and between adjacent filaments, radiation between adjacent filaments and convection with entrapped air. The magnitude of the mechanical deformation is also studied. Once this exercise is completed, it is possible to select the material properties, process variables and thermal phenomena that should be taken in for effective numerical modelling of FFE.

Refinement and variability techniques in model transformation of software requirements

Tese de Doutoramento em Tecnologias e Sistemas de Informação

Ensino, aprendizagem e avaliação no Ensino Superior: Perspetivas e práticas

Tese de Doutoramento em Ciências da Educação - Especialidade de Desenvolvimento Curricular

A demonstration case on the derivation of process-level logical architectures for ambient assisted living ecosystems

When representing the requirements for an intended software solution during the development process, a logical architecture is a model that provides an organized vision of how functionalities behave regardless of the technologies to be implemented. If the logical architecture represents an ambient assisted living (AAL) ecosystem, such representation is a complex task due to the existence of interrelated multidomains, which, most of the time, results in incomplete and incoherent user requirements. In this chap- ter, we present the results obtained when applying process-level modeling techniques to the derivation of the logical architecture for a real industrial AAL project. We adopt a V-Model–based approach that expresses the AAL requirements in a process-level perspec- tive, instead of the traditional product-level view. Additionally, we ensure compliance of the derived logical architecture with the National Institute of Standards and Technology (NIST) reference architecture as nonfunctional requirements to support the implementa- tion of the AAL architecture in cloud contexts.

Narrative innovations predict symptom improvement: Studying innovative moments in narrative therapy of depression

Objective:Innovative moments (IMs) are moments in the therapeutic dialog that constitute exceptions toward the client's problems. These narrative markers of meaning transformation are associated with change in different models of therapy and diverse diagnoses. Our goal is to test if IMs precede symptoms change, or, on the contrary, are a mere consequence of symptomatic 15 change. Method: For this purpose, IMs and symptomatology (Outcome Questionnaire-10.2) were assessed at every session in a sample of 10 cases of narrative therapy for depression. Hierarchical linear modeling was conducted to explore whether (i) IMs in a given session predict patients' symptoms in the following session and/or (ii) symptoms in a given session predict IMs in the next session. Results: Results suggested that IMs are better predictors of symptoms than the reverse. Conclusions: These results are discussed considering the contribution of meanings and narrative processes' changes to symptomatic improvement.

Implementação de ferramentas Lean numa empresa de componentes para calçado

Dissertação de mestrado em Engenharia Industrial

Aplicação de princípios e técnicas de Lean Manufacturing para melhoria do desempenho de linhas de montagem

Dissertação de mestrado integrado em Engenharia e Gestão Industrial

Sistema de controlo de processo e de organização numa empresa metalomecânica

Dissertação de mestrado em Engenharia Mecatrónica (área de especialização de Tecnologia de Manufatura)

Utilização de modelos de simulação para a melhoria de um sistema de restauração: estudo de caso de uma cantina universitária

Dissertação de mestrado em Engenharia Industrial

Estudo e implementação de testes de software em desenvolvimento ágil

Dissertação de mestrado em Engenharia de Sistemas

Frameworks no desenvolvimento de software: o caso da Elevation da PRIMAVERA BSS

Dissertação de mestrado integrado em Engenharia e Gestão de Sistemas de Informação

Feature Nets: behavioural modelling of software product lines

Software product lines (SPL) are diverse systems that are developed using a dual engineering process: (a)family engineering defines the commonality and variability among all members of the SPL, and (b) application engineering derives specific products based on the common foundation combined with a variable selection of features. The number of derivable products in an SPL can thus be exponential in the number of features. This inherent complexity poses two main challenges when it comes to modelling: Firstly, the formalism used for modelling SPLs needs to be modular and scalable. Secondly, it should ensure that all products behave correctly by providing the ability to analyse and verify complex models efficiently. In this paper we propose to integrate an established modelling formalism (Petri nets) with the domain of software product line engineering. To this end we extend Petri nets to Feature Nets. While Petri nets provide a framework for formally modelling and verifying single software systems, Feature Nets offer the same sort of benefits for software product lines. We show how SPLs can be modelled in an incremental, modular fashion using Feature Nets, provide a Feature Nets variant that supports modelling dynamic SPLs, and propose an analysis method for SPL modelled as Feature Nets. By facilitating the construction of a single model that includes the various behaviours exhibited by the products in an SPL, we make a significant step towards efficient and practical quality assurance methods for software product lines.