Infrared spectroscopic investigation of the effects of titania photocatalyst on the degradation of linear low density polyethylene film for commercial applications

There is a need in industry for a commodity polyethylene film with controllable degradation properties that will degrade in an environmentally neutral way, for applications such as shopping bags and packaging film. Additives such as starch have been shown to accelerate the degradation of plastic films, however control of degradation is required so that the film will retain its mechanical properties during storage and use, and then degrade when no longer required. By the addition of a photocatalyst it is hoped that polymer film will breakdown with exposure to sunlight. Furthermore, it is desired that the polymer film will degrade in the dark, after a short initial exposure to sunlight. Research has been undertaken into the photo- and thermo-oxidative degradation processes of 25 ìm thick LLDPE (linear low density polyethylene) film containing titania from different manufacturers. Films were aged in a suntest or in an oven at 50 °C, and the oxidation product formation was followed using IR spectroscopy. Degussa P25, Kronos 1002, and various organic-modified and doped titanias of the types Satchleben Hombitan and Hunstsman Tioxide incorporated into LLDPE films were assessed for photoactivity. Degussa P25 was found to be the most photoactive with UVA and UVC exposure. Surface modification of titania was found to reduce photoactivity. Crystal phase is thought to be among the most important factors when assessing the photoactivity of titania as a photocatalyst for degradation. Pre-irradiation with UVA or UVC for 24 hours of the film containing 3% Degussa P25 titania prior to aging in an oven resulted in embrittlement in ca. 200 days. The multivariate data analysis technique PCA (principal component analysis) was used as an exploratory tool to investigate the IR spectral data. Oxidation products formed in similar relative concentrations across all samples, confirming that titania was catalysing the oxidation of the LLDPE film without changing the oxidation pathway. PCA was also employed to compare rates of degradation in different films. PCA enabled the discovery of water vapour trapped inside cavities formed by oxidation by titania particles. Imaging ATR/FTIR spectroscopy with high lateral resolution was used in a novel experiment to examine the heterogeneous nature of oxidation of a model polymer compound caused by the presence of titania particles. A model polymer containing Degussa P25 titania was solvent cast onto the internal reflection element of the imaging ATR/FTIR and the oxidation under UVC was examined over time. Sensitisation of 5 ìm domains by titania resulted in areas of relatively high oxidation product concentration. The suitability of transmission IR with a synchrotron light source to the study of polymer film oxidation was assessed as the Australian Synchrotron in Melbourne, Australia. Challenges such as interference fringes and poor signal-to-noise ratio need to be addressed before this can become a routine technique.

Film, cinema, screen

Screen industries around the globe are evolving. While technological change has been slower to take effect upon the Australian film industry than other creative sectors such as music and publishing, all indications suggest that local screen practices are in a process of fundamental change. Fragmenting audiences, the growth of digital video, distribution and exhibition, the potential for entirely new forms of cultural expression, the proliferation of multi-platforms, and the importance of social networking and viral marketing in promoting products, are challenging traditional approaches to ‘film making’. Moreover, there has been a marked transition in government policy rationales and funding models in recent years, resulting in the most significant overhaul of public finance structures for the film industry in almost 20 years. Film, Cinema, Screen evaluates the Australian film industry’s recent development – particularly in terms of Australian feature film and television series production; it also advocates new approaches to Australian film, and address critical issues around how screen production globally is changing, with implications for local screen industries.

Lateral shearing interferometry, dynamic wavefront sensing, and high-speed videokeratoscopy for noninvasive assessment of tear film surface characteristics : a comparitive study

There are several noninvasive techniques for assessing the kinetics of tear film, but no comparative studies have been conducted to evaluate their efficacies. Our aim is to test and compare techniques based on high-speed videokeratoscopy (HSV), dynamic wavefront sensing (DWS), and lateral shearing interferometry (LSI). Algorithms are developed to estimate the tear film build-up time TBLD, and the average tear film surface quality in the stable phase of the interblink interval TFSQAv. Moderate but significant correlations are found between TBLD measured with LSI and DWS based on vertical coma (Pearson's r2=0.34, p<0.01) and higher order rms (r2=0.31, p<0.01), as well as between TFSQAv measured with LSI and HSV (r2=0.35, p<0.01), and between LSI and DWS based on the rms fit error (r2=0.40, p<0.01). No significant correlation is found between HSV and DWS. All three techniques estimate tear film build-up time to be below 2.5 sec, and they achieve a remarkably close median value of 0.7 sec. HSV appears to be the most precise method for measuring tear film surface quality. LSI appears to be the most sensitive method for analyzing tear film build-up.

Remediation strategies of shaft and common mode voltages in adjustable speed drive systems

AC motors are largely used in a wide range of modern systems, from household appliances to automated industry applications such as: ventilations systems, fans, pumps, conveyors and machine tool drives. Inverters are widely used in industrial and commercial applications due to the growing need for speed control in ASD systems. Fast switching transients and the common mode voltage, in interaction with parasitic capacitive couplings, may cause many unwanted problems in the ASD applications. These include shaft voltage and leakage currents. One of the inherent characteristics of Pulse Width Modulation (PWM) techniques is the generation of the common mode voltage, which is defined as the voltage between the electrical neutral of the inverter output and the ground. Shaft voltage can cause bearing currents when it exceeds the amount of breakdown voltage level of the thin lubricant film between the inner and outer rings of the bearing. This phenomenon is the main reason for early bearing failures. A rapid development in power switches technology has lead to a drastic decrement of switching rise and fall times. Because there is considerable capacitance between the stator windings and the frame, there can be a significant capacitive current (ground current escaping to earth through stray capacitors inside a motor) if the common mode voltage has high frequency components. This current leads to noises and Electromagnetic Interferences (EMI) issues in motor drive systems. These problems have been dealt with using a variety of methods which have been reported in the literature. However, cost and maintenance issues have prevented these methods from being widely accepted. Extra cost or rating of the inverter switches is usually the price to pay for such approaches. Thus, the determination of cost-effective techniques for shaft and common mode voltage reduction in ASD systems, with the focus on the first step of the design process, is the targeted scope of this thesis. An introduction to this research – including a description of the research problem, the literature review and an account of the research progress linking the research papers – is presented in Chapter 1. Electrical power generation from renewable energy sources, such as wind energy systems, has become a crucial issue because of environmental problems and a predicted future shortage of traditional energy sources. Thus, Chapter 2 focuses on the shaft voltage analysis of stator-fed induction generators (IG) and Doubly Fed Induction Generators DFIGs in wind turbine applications. This shaft voltage analysis includes: topologies, high frequency modelling, calculation and mitigation techniques. A back-to-back AC-DC-AC converter is investigated in terms of shaft voltage generation in a DFIG. Different topologies of LC filter placement are analysed in an effort to eliminate the shaft voltage. Different capacitive couplings exist in the motor/generator structure and any change in design parameters affects the capacitive couplings. Thus, an appropriate design for AC motors should lead to the smallest possible shaft voltage. Calculation of the shaft voltage based on different capacitive couplings, and an investigation of the effects of different design parameters are discussed in Chapter 3. This is achieved through 2-D and 3-D finite element simulation and experimental analysis. End-winding parameters of the motor are also effective factors in the calculation of the shaft voltage and have not been taken into account in previous reported studies. Calculation of the end-winding capacitances is rather complex because of the diversity of end winding shapes and the complexity of their geometry. A comprehensive analysis of these capacitances has been carried out with 3-D finite element simulations and experimental studies to determine their effective design parameters. These are documented in Chapter 4. Results of this analysis show that, by choosing appropriate design parameters, it is possible to decrease the shaft voltage and resultant bearing current in the primary stage of generator/motor design without using any additional active and passive filter-based techniques. The common mode voltage is defined by a switching pattern and, by using the appropriate pattern; the common mode voltage level can be controlled. Therefore, any PWM pattern which eliminates or minimizes the common mode voltage will be an effective shaft voltage reduction technique. Thus, common mode voltage reduction of a three-phase AC motor supplied with a single-phase diode rectifier is the focus of Chapter 5. The proposed strategy is mainly based on proper utilization of the zero vectors. Multilevel inverters are also used in ASD systems which have more voltage levels and switching states, and can provide more possibilities to reduce common mode voltage. A description of common mode voltage of multilevel inverters is investigated in Chapter 6. Chapter 7 investigates the elimination techniques of the shaft voltage in a DFIG based on the methods presented in the literature by the use of simulation results. However, it could be shown that every solution to reduce the shaft voltage in DFIG systems has its own characteristics, and these have to be taken into account in determining the most effective strategy. Calculation of the capacitive coupling and electric fields between the outer and inner races and the balls at different motor speeds in symmetrical and asymmetrical shaft and balls positions is discussed in Chapter 8. The analysis is carried out using finite element simulations to determine the conditions which will increase the probability of high rates of bearing failure due to current discharges through the balls and races.

Lateral shearing interferometry for analysis of tear film surface kinetics

Purpose: To date, there have been no measuring techniques available that could clearly identify all phases of tear film surface kinetics in one interblink interval. ----- ----- Methods: Using a series of cases, we show that lateral shearing interferometry equipped with a set of robust parameter estimation techniques is able to characterize up to five different phases of tear film surface kinetics that include: (i) initial fast tear film build-up phase, (ii) further slower tear film build-up phase, (iii) tear film stability, (iv) tear film thinning, and (v), after a detected break-up, subsequent tear film deterioration. ----- ----- Results: Several representative examples are given for estimating tear film surface kinetics in measurements in which the subjects were asked to blink and keep their eyes open as long as they could. ----- ----- Conclusions: Lateral shearing interferometry is a noninvasive technique that provides means for temporal characterization of tear film surface kinetics and the opportunity for the analysis of the two-step tear film build-up process.

Managing creativity and its paradoxes in the film industry

Purpose: The purpose of this paper is to illustrate the various types of paradoxes underlying the nature of creativity, which in turn affect the foundations of organizations and organization change in the 21 st century. The film industry best illustrate the interaction of such paradoxes, creativity and organizational change. This paper examines how small and medium-sized finns in the emerging Singapore film industry stay competitive by managing or not managing these paradoxes. Design/methodology/approach: The study reported in this paper explores the opinions, attitudes and experiences of key decision-makers in the Singaporean film industry. Findings: This paper introduces the idea that an analysis of the various paradoxes driven by creativity in today's society provides hints on a deeper understanding of organizational change and development in the 21" century. Practical implications: The findings indicate that managers need practical tools that will enable them to comprehend and better manage these emerging contradictions and fully understand the implications of paradoxical situations and organizational change. Research limitations: The distinctive nature of the Singaporean firms means that certain factors examined may be more or less significant in the film industry in other countries. Originality/value: The value of this paper lies in the knowledge that paradox considerations are becoming significant in understanding pluralism and the processes of organizational change.

Diversity in action : minority group media and social change

This audio magazine, written by Melissa Giles, features three Brisbane-based media organisations: Radio 4RPH, Queensland Pride and 98.9FM. [#1 - INTRODUCTION - read by Sara Cowling]----- [#2 - RADIO 4RPH: SHARING THE WORD - read by Ellen-Maree Elliot (and Sara Cowling)]----- [#3 - QUEENSLAND PRIDE: OUT IN THE STREET - read by Dominique Wiehahn (and Sara Cowling)]----- [#4 - 98.9FM: BREAKING THE MOULD - read by Paige Ross (and Sara Cowling)]----- [#5 - CONCLUSION - read by Sara Cowling]

Non-invasive assessment of tear film surface quality

The tear film plays an important role preserving the health of the ocular surface and maintaining the optimal refractive power of the cornea. Moreover dry eye syndrome is one of the most commonly reported eye health problems. This syndrome is caused by abnormalities in the properties of the tear film. Current clinical tools to assess the tear film properties have shown certain limitations. The traditional invasive methods for the assessment of tear film quality, which are used by most clinicians, have been criticized for the lack of reliability and/or repeatability. A range of non-invasive methods of tear assessment have been investigated, but also present limitations. Hence no “gold standard” test is currently available to assess the tear film integrity. Therefore, improving techniques for the assessment of the tear film quality is of clinical significance and the main motivation for the work described in this thesis. In this study the tear film surface quality (TFSQ) changes were investigated by means of high-speed videokeratoscopy (HSV). In this technique, a set of concentric rings formed in an illuminated cone or a bowl is projected on the anterior cornea and their reflection from the ocular surface imaged on a charge-coupled device (CCD). The reflection of the light is produced in the outer most layer of the cornea, the tear film. Hence, when the tear film is smooth the reflected image presents a well structure pattern. In contrast, when the tear film surface presents irregularities, the pattern also becomes irregular due to the light scatter and deviation of the reflected light. The videokeratoscope provides an estimate of the corneal topography associated with each Placido disk image. Topographical estimates, which have been used in the past to quantify tear film changes, may not always be suitable for the evaluation of all the dynamic phases of the tear film. However the Placido disk image itself, which contains the reflected pattern, may be more appropriate to assess the tear film dynamics. A set of novel routines have been purposely developed to quantify the changes of the reflected pattern and to extract a time series estimate of the TFSQ from the video recording. The routine extracts from each frame of the video recording a maximized area of analysis. In this area a metric of the TFSQ is calculated. Initially two metrics based on the Gabor filter and Gaussian gradient-based techniques, were used to quantify the consistency of the pattern’s local orientation as a metric of TFSQ. These metrics have helped to demonstrate the applicability of HSV to assess the tear film, and the influence of contact lens wear on TFSQ. The results suggest that the dynamic-area analysis method of HSV was able to distinguish and quantify the subtle, but systematic degradation of tear film surface quality in the inter-blink interval in contact lens wear. It was also able to clearly show a difference between bare eye and contact lens wearing conditions. Thus, the HSV method appears to be a useful technique for quantitatively investigating the effects of contact lens wear on the TFSQ. Subsequently a larger clinical study was conducted to perform a comparison between HSV and two other non-invasive techniques, lateral shearing interferometry (LSI) and dynamic wavefront sensing (DWS). Of these non-invasive techniques, the HSV appeared to be the most precise method for measuring TFSQ, by virtue of its lower coefficient of variation. While the LSI appears to be the most sensitive method for analyzing the tear build-up time (TBUT). The capability of each of the non-invasive methods to discriminate dry eye from normal subjects was also investigated. The receiver operating characteristic (ROC) curves were calculated to assess the ability of each method to predict dry eye syndrome. The LSI technique gave the best results under both natural blinking conditions and in suppressed blinking conditions, which was closely followed by HSV. The DWS did not perform as well as LSI or HSV. The main limitation of the HSV technique, which was identified during the former clinical study, was the lack of the sensitivity to quantify the build-up/formation phase of the tear film cycle. For that reason an extra metric based on image transformation and block processing was proposed. In this metric, the area of analysis was transformed from Cartesian to Polar coordinates, converting the concentric circles pattern into a quasi-straight lines image in which a block statistics value was extracted. This metric has shown better sensitivity under low pattern disturbance as well as has improved the performance of the ROC curves. Additionally a theoretical study, based on ray-tracing techniques and topographical models of the tear film, was proposed to fully comprehend the HSV measurement and the instrument’s potential limitations. Of special interested was the assessment of the instrument’s sensitivity under subtle topographic changes. The theoretical simulations have helped to provide some understanding on the tear film dynamics, for instance the model extracted for the build-up phase has helped to provide some insight into the dynamics during this initial phase. Finally some aspects of the mathematical modeling of TFSQ time series have been reported in this thesis. Over the years, different functions have been used to model the time series as well as to extract the key clinical parameters (i.e., timing). Unfortunately those techniques to model the tear film time series do not simultaneously consider the underlying physiological mechanism and the parameter extraction methods. A set of guidelines are proposed to meet both criteria. Special attention was given to a commonly used fit, the polynomial function, and considerations to select the appropriate model order to ensure the true derivative of the signal is accurately represented. The work described in this thesis has shown the potential of using high-speed videokeratoscopy to assess tear film surface quality. A set of novel image and signal processing techniques have been proposed to quantify different aspects of the tear film assessment, analysis and modeling. The dynamic-area HSV has shown good performance in a broad range of conditions (i.e., contact lens, normal and dry eye subjects). As a result, this technique could be a useful clinical tool to assess tear film surface quality in the future.

Nurses driving change to improve access to education and quality in lcinical teaching : A partnership between Australia and Viet Nam

In Viet Nam, standards of nursing care fail to meet international competency standards. This increases risks to patient safety (eg. hospital acquired infection), consequently the Ministry of Health identified the need to strengthen nurse education in Viet Nam. This paper presents experiences of a piloted clinical teaching model developed in Ha Noi, to strengthen nurse led institutional capacity for in-service education and clinical teaching. Historically 90% of nursing education was conducted by physicians and professional development in hospitals for nurses was limited. There was minimal communication between hospitals and nursing schools about expectations of students and assessment and quality of the learning experience. As a result when students came to the clinical sites, no-one understood how to plan their learning objectives and utilise teaching and learning approaches appropriate to their level. Therefore student learning outcomes were variable. They focussed on procedures and techniques and “learning how to do” rather than learning how to plan, implement and evaluate patient care. This project is part of a multi-component capacity building program designed to improve nurse education in Viet Nam. The project was funded jointly by Queensland University of Technology (QUT) and the Australian Agency for International Development. Its aim was to develop a collaborative clinically-based model of teaching to create an environment that encourages evidence-based, student-centred clinical learning. Accordingly, strategies introduced promoted clinical teaching of competency based nursing practice utilising the regionally endorsed nurse core competency standards. Thirty nurse teachers from Viet Duc University Hospital and Hanoi Medical College participated in the program. These nurses and nurse teachers undertook face to face education in three workshops, and completed three assessment items. Assessment was applied, where participants integrated the concepts learned in each workshop and completed assessment tasks related to planning, implementing and evaluating teaching in the clinical area. Twenty of these participants were then selected to undertake a two week study tour in Brisbane, Australia where the clinical teaching model was refined and an action plan developed to integrate into both organisations with possible implementation across Viet Nam. Participants on this study tour also experienced clinical teaching and learning at QUT by attending classes held at the university, and were able to visit selected hospitals to experience clinical teaching in these settings as well. Effectiveness of the project was measured throughout the implementation phase and in follow up visits to the clinical site. To date changes have been noted on an individual and organisational level. There is also significant planning underway to incorporate the clinical teaching model developed across the organisation and how this may be implemented in other regions. Two participants have also been involved in disseminating aspects of this approach to clinical teaching in Ho Chi Minh, with further plans for more in-depth dissemination to occur throughout the country.

Documentary as history, memory, dream and film

A century ago, as the Western world embarked on a period of traumatic change, the visual realism of photography and documentary film brought print and radio news to life. The vision that these new mediums threw into stark relief was one of intense social and political upheaval: the birth of modernity fired and tempered in the crucible of the Great War. As millions died in this fiery chamber and the influenza pandemic that followed, lines of empires staggered to their fall, and new geo-political boundaries were scored in the raw, red flesh of Europe. The decade of 1910 to 1919 also heralded a prolific period of artistic experimentation. It marked the beginning of the social and artistic age of modernity and, with it, the nascent beginnings of a new art form: film. We still live in the shadow of this violent, traumatic and fertile age; haunted by the ghosts of Flanders and Gallipoli and its ripples of innovation and creativity. Something happened here, but to understand how and why is not easy; for the documentary images we carry with us in our collective cultural memory have become what Baudrillard refers to as simulacra. Detached from their referents, they have become referents themselves, to underscore other, grand narratives in television and Hollywood films. The personal histories of the individuals they represent so graphically–and their hope, love and loss–are folded into a national story that serves, like war memorials and national holidays, to buttress social myths and values. And, as filmic images cross-pollinate, with each iteration offering a new catharsis, events that must have been terrifying or wondrous are abstracted. In this paper we first discuss this transformation through reference to theories of documentary and memory–this will form a conceptual framework for a subsequent discussion of the short film Anmer. Produced by the first author in 2010, Anmer is a visual essay on documentary, simulacra and the symbolic narratives of history. Its form, structure and aesthetic speak of the confluence of documentary, history, memory and dream. Located in the first decade of the twentieth century, its non-linear narratives of personal tragedy and poetic dreamscapes are an evocative reminder of the distance between intimate experience, grand narratives, and the mythologies of popular films. This transformation of documentary sources not only played out in the processes of the film’s production, but also came to form its theme.

Dimensions of the third sector : comparative perspectives on structure and change

Cross-nationally, the introduction of New Public Management coincides with a significant growth phase of the nonprofit or third sector. This growth has disproportionately been an expansion of the economic dimensions (employment, turnover) and basically involved the greater use of third sector organisations as service providers. Such provision uses complex contract regimes, and typically takes place in some form of public-private partnership with either public or private funding agencies. Other parts of the third sector such as membership, volunteering and giving have generally grown less. The paper suggests that the sector is becoming qualitatively different, although the nature and strength of this change depends on the nonprofit regime type in a given country. Generally, however, third sector growth has led to differentiation processes that involve new organisational forms, and changes in activities and overall composition. The paper explores the measurement aspects of the quantitative-qualitative jump in third sector development by trying to "map" changes in core facts or dimensions over time. In closing, the paper suggests to examine recombination and refunctionality processes in the third sector.

Pt/ZnO/SiC thin film for hydrogen gas sensing

Zinc oxide (ZnO) is one of the most promising electronic and photonic materials to date. In this work, we present an enhanced ZnO Schottky gas sensor deposited on SiC substrates in comparison to those reported previously in literature. The performance of ZnO/SiC based Schottky thin film gas sensors produced a forward lateral voltage shift of 12.99mV and 111.87mV in response to concentrations of hydrogen gas at 0.06% and 1% in air at optimum temperature of 330 ºC. The maximum change in barrier height was calculated as 37.9 meV for 1% H2 sensing operation at the optimum temperature.

Children as change agents for sustainability : an action research case study in a kindergarten

At a time when global consumption and production levels are 25 percent higher than the Earth’s sustainable carrying capacity, there are worldwide calls to find ways to sustain the Earth for this and future generations. A central premise of this study is that education systems have an obligation to participate in this move towards sustainability and can respond by embedding education for sustainability into curricula. This study took early childhood education as its focus due to the teacherresearcher’s own concerns about the state of the planet, coupled with early childhood education’s established traditions of nature-based and child-centred pedagogy. The study explored the experiences of a class of kindergarten children as they undertook a Project Approach to learning about environmental sustainability. The Project Approach is an adaptation of Chard’s work which is situated within a constructivist theoretical framework (Chard, 2011). The Project Approach involves in-depth investigations around an identified topic of interest. It has three phases: introductory, synthesising and culminating phase. The study also investigated the learning journey of the classroom teacher/researcher who broadened her long-held co-constructivist teaching approaches to include transformative practices in order to facilitate curriculum which embedded education for sustainability. While coconstructivist approaches focus on the co-construction of knowledge, transformative practices are concerned with creating change. An action research case study was conducted. This involved twenty-two children who attended an Australian kindergarten. Data were collected and analysed over a seven week period. The study found that young children can be change agents for sustainability when a Project Approach is broadened to include transformative practices. The study also found that the child participants were able to think critically about environmental and sustainability issues, were able to create change in their local contexts, and took on the role of educators to influence others’ environmental behaviours. Another finding was that the teacher-researcher’s participation in the study caused a transformation of both her teaching philosophy and the culture at the kindergarten. An important outcome of the study was the development of a new curriculum model that integrates and has applicability for curriculum development and teacher practice.

Microstructure of an artificial grain boundary weak link in an YBa2Cu3O(7-δ) thin film grown on a (100)(110), [001]-tilt Y-ZrO2 bicrystal

The microstructure of an artificial grain boundary in an YBa2Cu3O7-δ (YBCO) thin film grown on a (100)(110), [001]-tilt yttria-stabilized-zirconia (YSZ) bicrystal substrate has been studied using transmission electron microscopy (TEM). The orientation relationship between the YBCO film and the YSZ substrate was [001]YBCO∥[001]YSZ and [110]YBCO∥[100]YSZ for each half of the bicrystal film. However, the exact boundary geometry of the bicrystal substrate was not transferred to the film. The substrate boundary was straight while the film boundary was wavy. In several cases there was bending of the lattice confined within a distance of a few basal-plane lattice spacings from the boundary plane and microfaceting. No intergranular secondary phase was observed but about 25% of the boundary was covered by c-axis-tilted YBCO grains and a-axis-oriented grains, both of which were typically adjacent to CuO grains or surrounded by a thin Cu-rich amorphous layer.

Characterisation of two distinctly different processes associated with the electrocrystallization of microcrystals of phase I CuTCNQ (TCNQ= 7, 7, 8, 8-tetracyanoquinodimethane)

Semi-conducting phase I CuTCNQ (TCNQ = 7,7,8,8-tetracyanoquinodimethane), which is of considerable interest as a switching device for memory storage materials, can be electrocrystallized from CH3CN via two distinctly different pathways when TCNQ is reduced to TCNQ˙− in the presence of [Cu(MeCN)4]+. The first pathway, identified in earlier studies, occurs at potentials where TCNQ is reduced to TCNQ˙− and involves a nucleation–growth mechanism at preferred sites on the electrode to produce arrays of well separated large branched needle-shaped phase I CuTCNQ crystals. The second pathway, now identified at more negative potentials, generates much smaller needle-shaped phase I CuTCNQ crystals. These electrocrystallize on parts of the surface not occupied in the initial process and give rise to film-like characteristics. This process is attributed to the reduction of Cu+[(TCNQ˙−)(TCNQ)] or a stabilised film of TCNQ via a solid–solid conversion process, which also involves ingress of Cu+via a nucleation–growth mechanism. The CuTCNQ surface area coverage is extensive since it occurs at all areas of the electrode and not just at defect sites that dominate the crystal formation sites for the first pathway. Infrared spectra, X-ray diffraction, surface plasmon resonance, quartz crystal microbalance, scanning electron microscopy and optical image data all confirm that two distinctly different pathways are available to produce the kinetically-favoured and more highly conducting phase I CuTCNQ solid, rather than the phase II material.